Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LOW DENSITY GAS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Electrospun Nanofiber Electrodes for High and Low Humidity PEMFC Operation

MEAs with nanofiber mat electrodes containing Pt/C catalyst and Nafion binder were fabricated and evaluated. The electrodes were prepared by electrospinning a solution of catalyst powder, salt-form Nafion (with Na + , Li + , or Cs + as the sulfonic acid counterion), and a carrier polymer of either polyethylene oxide or poly(acrylic acid). The carrier polymer was extracted prior to MEA testing by a hot water soaking step. The resulting fibers were 15%–17% porous, with a core–shell-like morphology (a coating of primarily Nafion on the fiber surface). MEAs with anode/cathode catalyst loadings of 0.1 mg Pt cm −2 each and a Nafion 211 membrane produced high power at both high and low relative humidity (RH) conditions in H 2 /air fuel cell tests, e.g., a maximum power density of 919 mW cm −2 at 100% RH and 832 mW cm −2 at 40% RH for a test at 80 °C and 200 kPa abs . The presence of nm-size pores within the fibers trapped water via capillary condensation during low RH feed gas testing, thus maintaining a high proton conductivity of the Nafion binder in the anode and cathode while minimizing/eliminating ionic isolation of catalyst particles in low water content, poorly conductive binder.

25 ENERGY STORAGE↗
DOE OSTI2025

Low Temperature CO 2 Hydrogenation on Unsupported Mo 2 C Catalysts

CO 2 hydrogenation to methanol, a key reaction for decarbonizing the fuel and chemical industries, requires catalyst formulations that hydrogenate CO 2 selectively to methanol at temperatures where methanol conversion is not significantly equilibrium limited (<423 K). Herein we report continuous CO 2 hydrogenation at low temperatures (348-408 K, H 2 /CO 2 = 0.1-50, 5-35 bar) with high selectivity to methanol (up to ca. 80%) over unsupported β-Mo 2 C catalysts. Active site density quantification via titration with trifluoroacetic acid at reaction temperatures enables an assessment of site-specific rates. Methanation and reverse water gas shift (RWGS) occur concurrently with methanol synthesis during CO 2 hydrogenation over Mo 2 C. Reaction pathway analysis, product cofeeds, and reversibility formalisms show that all products form through primary reaction pathways from CO 2 , but secondary reactions of CO contribute significantly to rates of methanation. Dependences of forward rates on reactant and product concentration determined by independently varying the CO 2 , H 2 , CO, H 2 O, CH 3 OH, and CH 4 pressure in conjunction with reversibility formalisms reveal that all products form through H-assisted CO 2 activation and involve partially hydrogenated CO 2 -derived intermediates. Here, these inferences were verified by quantitative agreement between measured site-time yields and site-time yields predicted by closed form kinetic rate expressions in an integral reactor model over widely varying conditions (85-2000 kPa H 2 , 80-1500 kPa CO 2 , 0-45 kPa H 2 O, 0-21 kPa CO, 0-25 kPa CH 3 OH, 0-75 kPa CH 4 , 5-87 mol Mo s s mol CO 2 -1 ). Coverages calculated based on the kinetic model reveal that the Mo 2 C surface is covered with bidentate CO- and CO 2 -derived intermediates of the stoichiometry H 2 CO 2 and H 2 CO, indicating that H 2 and CO x do not compete for surface occupancy but instead adsorb cooperatively to form partially hydrogenated intermediates. Hydrogenation of the CO-derived H 2 CO** intermediate favors methanation, while hydrogenation of CO 2 -derived H 2 CO 2 ** favors methanol synthesis. Together, these findings demonstrate the ability of unsupported Mo 2 C to catalyze the hydrogenation of CO 2 to methanol at low temperatures and provide insight into the reaction network and mechanisms involved in its formation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Experimental and numerical investigation of flame stabilization and pollutant formation in matrix stabilized ammonia-hydrogen combustion

Ammonia (NH 3 ) is a carbon-free fuel that offers an attractive alternative for reducing greenhouse gas emissions. However, the slow flame speed, low heating value, and emissions of nitrogen-containing pollutants present significant issues for practical combustion applications. To address these issues, we investigate the use of matrix stabilized combustion. In this type of burner, combustion is performed within an inert porous ceramic foam, heat is recirculated by solid conduction and radiation, which enhances flame speed and combustion stabilization, thereby permitting combustion over a wide range of equivalence ratio conditions. We present a new porous media burner (PMB) capable of stabilizing NH 3 /air flames at ambient conditions. An extensive experimental characterization of the stability of this burner is conducted with up to 30% by volume of hydrogen (H 2 ) in the fuel stream. A 15:1 turndown ratio is demonstrated, with a high thermal power density of 62 MW m -3 . Concentrations of NO, unburnt NH 3 , and H 2 in the exhaust stream are measured. Two regimes are identified for low NO operation: rich and very lean. For rich conditions, NO emissions decrease with increasing equivalence ratio and decreasing H 2 blending. Unburnt NH 3 emissions follow opposite trends. These measurements are complemented by simulations in which the burner is represented by a coupled solid-gas reactor network. In conclusion, this model captures the burner’s pollutant emissions to good accuracy and is used to analyze the mechanisms of pollutant formation.

42 ENGINEERING↗
DOE OSTI2024

Low Thermal Conductivity and Diffusivity at High Temperatures Using Stable High–Entropy Spinel Oxide Nanoparticles

The realization of low thermal conductivity at high temperatures (0.11 W m –1 K –1 800 °C) in ambient air in a porous solid thermal insulation material, using stable packed nanoparticles of high-entropy spinel oxide with 8 cations (HESO-8 NPs) with a relatively high packing density of ≈50%, is reported. The high-density HESO-8 NP pellets possess around 1000-fold lower thermal diffusivity than that of air, resulting in much slower heat propagation when subjected to a transient heat flux. The low thermal conductivity and diffusivity are realized by suppressing all three modes of heat transfer, namely solid conduction, gas conduction, and thermal radiation, via stable nanoconstriction and infrared-absorbing nature of the HESO-8 NPs, which are enabled by remarkable microstructural stability against coarsening at high temperatures due to the high entropy. Furthermore, this work can elucidate the design of the next-generation high-temperature thermal insulation materials using high-entropy ceramic nanostructures.

thermal insulation↗
DOE OSTI2021

Microemulsions in the driven Widom-Rowlinson lattice gas

An investigation of the two-dimensional Widom-Rowlinson lattice gas under an applied drive uncovered a remarkable nonequilibrium steady state in which uniform stripes (reminiscent of an equilibrium lamellar phase) form perpendicular to the drive direction [R. Dickman and R. K. P. Zia, Phys. Rev. E 97, 062126 (2018)]. Here we study this model at low particle densities in two and three dimensions, where we find a disordered phase with a characteristic length scale (a “microemulsion”) along the drive direction. Further we develop a continuum theory of this disordered phase to derive a coarse-grained field-theoretic action for the nonequilibrium dynamics. The action has the form of two coupled driven diffusive systems with different characteristic velocities, generated by an interplay between the particle repulsion and the drive. We then show how fluctuation corrections in the field theory may generate the characteristic features of the microemulsion phase, including a peak in the static structure factor corresponding to the characteristic length scale. This work lays the foundation for understanding the stripe phenomenon more generally.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Microstructure, stored energy, and stability of H/He-filled nanocavities in low temperature irradiated Inconel 718

The microstructure, trapped transmutation gases, stored energy, and mechanical behavior of samples from an irradiated Inconel 718 proton beam window were characterized using transmission electron microcopy, thermal desorption spectrometry (TDS), differential scanning calorimetry (DSC), and tensile testing. In the as-irradiated condition the microstructure contained a high number density of 1–3 nm gas-filled nanocavities. Emissions of trapped gases, H and He, during TDS correlated with peaks of the energy release curves from DSC examinations, which suggest these gases were likely stored in highly stable defect traps. The stored energy from radiation damage saturated at doses of a few dpa and did not increase with increasing radiation dose, but the amount of stored H and He increased with increasing dose. Effects of post-irradiation annealing were studied as well. After exposure to 700 °C, the nanocavities grew only slightly to 2–4 nm in diameter, but after exposure to 900 °C, the cavities grew to 10–20 nm in diameter and electron energy-loss spectroscopy showed these cavities contained a core of He surrounded by a shell of H. Further, this study demonstrated that the irradiation defect structures containing H and He were remarkably stable during irradiation and after exposure up to 700 °C. The effect of the irradiation temperature, defect mobility, and interaction of H, He, and irradiation defects on mechanical behavior provides insight into the processes responsible for the unusual recovery in ductility with increasing radiation dose observed in Inconel 718 after high energy proton and spallation neutron irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Study of a linear surface wave plasma source for tin removal in an extreme ultraviolet source

Tin deposition mitigation employs hydrogen radicals and ions, formed in a hydrogen plasma, to interact with tin to form tin hydride (SnH 4 ) in the gaseous state, which is then pumped away. Surface wave plasma (SWP) technology developed at Illinois generates hydrogen radicals and ions, resulting in tin etch rates that are high enough to keep extreme ultraviolet (EUV) lithographic tools clean. An advantage of an SWP antenna is the ability to generate a high density of hydrogen radicals and hydrogen ions directly at the desired etching location. In situ etching of tin enables high availability EUV tools by maintaining high reflectivity of the multilayer mirror of the collector. Additionally, the SWP is characterized with low ion energies and low electron temperature, such that the multilayer mirror does not suffer any damage from sputtering or implantation of hydrogen ions during operation. Here, experiments elucidating the fundamental processes of tin removal are conducted by varying pressure, power, surface temperature, and gas flow rate in order to observe the etch rate behavior. Our results have shown that the presence of hydrogen ions increases etch rates because ion bombardment weakens Sn–Sn bonds, which, in turn, allows for a higher rate of chemical etching by the radicals. The ion bombardment reduces the number of radicals needed to etch a single tin atom to the range of 10 2 –10 3 . The linear SWP antenna yields plasma densities on the order of 10 17 to 10 18 m -3 and radical densities on the order of 10 18 to 10 19 m -3 , allowing for greater utilization of ion etch enhancement. Etch rates of up to 200 nm/min have been achieved. The surface temperature of the samples is an important factor in the etching process such that the decrease in the surface temperature increases the etch rates and decreases the hydrogen desorption rates. In addition, a kinetic etch model is developed to explain the behavior of etch rates as a function of surface temperature. Furthermore, results from experiments performed in an Illinois NXE:3100 chamber will be discussed.

42 ENGINEERING↗
DOE OSTI2025

Computational Design of Cost-Effective High-Entropy Thermal/Environmental Barrier Coatings

Developing cost-effective thermal/environmental barrier coatings (TEBC) requires balance among various properties including low thermal conductivity, matching coefficient of thermal expansion (CTE), high thermal stability, high fracture toughness, and high recession resistance while being affordable. Low oxygen diffusivity is desirable as it can slow down oxygen transport to reach the underlying bond coating and hence delay oxidation of the bond coating. This project aims to design low-cost high-performance TEBC based on high entropy rare earth disilicates to protect SiC-based ceramic matrix composites from chemical and thermal attack for better performance of components in the hot section of gas turbine engines. To accelerate the TEBC design, we utilize first-principles density functional theory to predict key properties including phase stability, CTE, lattice thermal conductivity, temperature-dependent elastic constants, and oxygen diffusivity. Alloying elements including Yb, Y, Er, Eu, Gd, Lu, La, and Ce are considered, and modeling prediction are compared with available experimental results.

coefficient of thermal expansion↗
DOE OSTI2025

Relationship between microporous structure and light gas transport through glassy polymeric membranes revealed by molecular simulations

Microporous glassy polymers are attractive materials for gas separation membranes, due to their high permeability and tailorable selectivity, provided physical aging can be delayed. The archetypal microporous glassy polymer, PTMSP, can be blended with a hyper-crosslinked isatin–triptycene porous polymer network (PPN) to delay physical aging. However, while PPN is effective at reducing physical aging, it also affects the permeability of light gases through PTMSP. Molecular dynamics simulations were used here to shed fundamental light on the mechanisms responsible for these effects. Atomistic models are developed that satisfactorily reproduce experimental observations such as matrix density and cavity size distributions for neat PTMSP as well as for PTMSP–PPN blends. Analysis of the simulation results suggests that physical aging is delayed because the PPN inclusions slow down PTMSP relaxation while reducing the connectivity between free volume pockets. To understand how PPN inclusions affect light gas permeability, the atomistic models developed are used to probe CO 2 and CH 4 diffusion and sorption. These simulations are conducted for PTMSP matrices exhibiting varying density, towards reproducing experimental permeability data. Interrogating the simulation trajectories, it is discovered that while CH 4 travels preferentially through the free volume cavities, CO 2 preferentially interacts with the available surfaces, especially in the presence of PPN. These differences help interpret experimental observations. The transport of C 2 H 6 and H 2 S through PTMSP matrices was also investigated. These gases, and in particular H 2 S, were found to absorb within PTMSP, yielding very low diffusion coefficients. The ability to predict differences in diffusion pathways for various natural gas components unveils the possibility of engineering membranes to control permeability and selectivity towards large-scale applications.

Bao Le, Tran Thi [Univ. of Oklahoma, Norman, OK (U↗
DOE OSTI2022

High-density polarization-induced 2D electron gases in N-polar pseudomorphic undoped GaN/Al 0.85 Ga 0.15 N heterostructures on single-crystal AlN substrates

The polarization difference and band offset between Al(Ga)N and GaN induce two-dimensional (2D) free carriers in Al(Ga)N/GaN heterojunctions without any chemical doping. A high-density 2D electron gas (2DEG), analogous to the recently discovered 2D hole gas in a metal-polar structure, is predicted in a N-polar pseudomorphic GaN/Al(Ga)N heterostructure on unstrained AlN. We report the observation of such 2DEGs in N-polar undoped pseudomorphic GaN/AlGaN heterostructures on single-crystal AlN substrates by molecular beam epitaxy. With a high electron density of ~4.3 ×10 13 /cm 2 that maintains down to cryogenic temperatures and a room temperature electron mobility of ~450 cm 2 /V s, a sheet resistance as low as ~320 Ω/$\Box$ is achieved in a structure with an 8 nm GaN layer. Finally, these results indicate significant potential of AlN platform for future high-power RF electronics based on N-polar III-nitride high electron mobility transistors.

42 ENGINEERING↗
DOE OSTI2021

Construction of an Anion-Pillared MOF Database and the Screening of MOFs Suitable for Xe/Kr Separation

The separation of xenon/krypton (Xe/Kr) mixtures is a challenging process. Many porous materials allow the adsorption of both Xe and Kr but only with low selectivity. Anion-pillared metal–organic frameworks (MOFs), featuring the anion groups as structural pillars, show potential in gas separations, but only a limited number of them have been synthesized. Here, we describe a collection of 936 anion-pillared MOFs based on 22 experimentally available structures. We performed density functional theory (DFT) optimization and then assigned density-derived electrostatic and chemical (DDEC) charges for each MOF to make them well suited to molecular simulations. The structural properties of the MOFs vary more strongly with the choice of the organic ligand than with other aspects like fluorine groups and metal centers. We then screened the entire collection of MOFs in the context of Xe/Kr separation at room temperature. Compared with previously reported MOFs, the interpenetrated MOF SIFSIX-6-Cd-i is predicted to perform better for Xe/Kr separations, with a good balance between working capacity (1.62 mmol/g) and separation selectivity (16.4) at 298 K and 100 kPa. Here, we also found that the heterogeneity of fluorine groups within a MOF can help to enhance Xe working capacity without reducing the Xe/Kr selectivity, suggesting that synthesis of anion-pillared MOFs with mixed fluorine groups may lead to improved Xe/Kr separation performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Pressurized Gas-Driven Elemental Redistribution Enables Ultrastable PtNi Catalysts for Heavy-Duty Vehicles

Gas-driven element redistribution, characterized by the preferential enrichment of one element at the surface relative to the bulk, is frequently observed in multicomponent alloys. Using L1 0 -ordered PtNi as a model system, we reveal that gas pressure plays a critical role in governing adsorption-driven surface composition during annealing in reducing gases: low pressure favors Pt surface segregation, while high pressure facilitates Ni surface enrichment. In this study, we developed a high-pressure nitriding (HPN) strategy that modulates the surface structure and composition of PtNi catalysts. The resulting HPN-PtNi exhibits enhanced performance and durability in membrane electrode assemblies for heavy-duty fuel cell applications, maintaining a high current density of 1.19 A cm −2 at 0.7 V after 90,000 voltage cycles. Through a combination of experimental and theoretical analyses, we reveal that the HPN process forms additional stabilizing Ni−N bonds and induces elemental redistribution with Ni surface enrichment and a Ni-deficient Pt subsurface. These modifications alter the atomic coordination environment of the ordered PtNi phase. This work presents a generalizable strategy to design robust and high-performing Pt-based catalysts by controlling gas-pressure-driven elemental redistribution and dopant incorporation.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Low-Energy Ion Scattering Intensities from Supported Nanoparticles: The Spherical Cap Model

Supported nanoparticles are of great importance to many technologies like fuel processing and chemical synthesis using catalysts and electrocatalysts, energy storage and generation using fuel cells and batteries, electrochemistry, magnetic information storage, and more. Low-energy ion scattering spectroscopy (LEIS) with noble gas ions like He+ is a powerful tool for the characterization of nanoparticles dispersed across flat support surfaces due to its ability to probe the elemental composition in the topmost atomic layer of a surface, providing quantitative information regarding the size and number density of nanoparticles. In this work, we present a derivation of the LEIS intensities expected from nanoparticles and the support material as a function of the average particle size, their number per unit area, and their contact angle with the support when modeled as spherical caps of the nanoparticle material dispersed over the surface of a flat support. The model assumes that the ion intensities are determined only by the physical blocking of linear ion trajectories and independent of the tilt angle of the local surface relative to the incident and scattered ion directions, an assumption we support by quantitative modeling of published data which tested tilt-angle effects. The model is a generalization to arbitrary contact angles of the hemispherical cap model, which assumes 90° contact angle and has been widely used to model spectroscopic signals in LEIS (and also in Auger and photoelectron spectroscopies) during nanoparticle growth. Here, this new model quantitatively reveals how LEIS signals are sensitive not only to the diameter and number density of the nanoparticle but also to their contact angle (or height/diameter ratio). With the use of additional data (e.g., from microscopy or adsorption microcalorimetry), the model presented here will enable more accurate determination of the average size, shape, and number density of supported nanoparticles based on LEIS intensity measurements.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2022

Kinetic Control of Angstrom-Scale Porosity in 2D Lattices for Direct Scalable Synthesis of Atomically Thin Proton Exchange Membranes

Angstrom-scale pores introduced into atomically thin 2D materials offer transformative advances for proton exchange membranes in several energy applications. Here, we show that facile kinetic control of scalable chemical vapor deposition (CVD) can allow for direct formation of angstrom-scale proton-selective pores in monolayer graphene with significant hindrance to even small, hydrated ions (K + diameter ~6.6 Å) and gas molecules (H 2 kinetic diameter ~2.9 Å). We demonstrate centimeter-scale Nafion|Graphene|Nafion membranes with proton conductance ~3.3–3.8 S cm –2 (graphene ~12.7–24.6 S cm –2 ) and H + /K + selectivity ~6.2–44.2 with liquid electrolytes. The same membranes show proton conductance ~4.6–4.8 S cm –2 (graphene ~39.9–57.5 S cm –2 ) and extremely low H 2 crossover ~1.7 × 10 –1 – 2.2 × 10 –1 mA cm –2 (~0.4 V, ~25 °C) with H 2 gas feed. We rationalize our findings via a resistance-based transport model and introduce a stacking approach that leverages combinatorial effects of interdefect distance and interlayer transport to allow for Nafion|Graphene|Graphene|Nafion membranes with H + /K + selectivity ~86.1 (at 1 M) and record low H 2 crossover current density ~2.5 × 10 –2 mA cm –2 , up to ~90% lower than state-of-the-art ionomer Nafion membranes ~2.7 × 10 –1 mA cm –2 under identical conditions, while still maintaining proton conductance ~4.2 S cm –2 (graphene stack ~20.8 S cm –2 ) comparable to that for Nafion of ~5.2 S cm –2 . Furthermore, our experimental insights enable functional atomically thin high flux proton exchange membranes with minimal crossover.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Circular Reprocessing of Thermoset Polyurethane Foams

Thermoset polyurethane (PU) foams are widely used in industrial applications, but they cannot be recycled by conventional melt reprocessing because of their cross-linked structures. The introduction of carbamate exchange catalysts converts thermoset PU into covalent adaptable networks (CANs), which are amenable to reprocessing at elevated temperatures. However, this approach has produced solid PU films, which have fewer uses and lower commercial demand. In this work, simultaneous reprocessing and refoaming of thermoset PU foams is demonstrated by leveraging the melt-processability of PU CANs and allowing cell growth by gas generation in a twin-screw extruder. The optimal operating temperature of the refoaming process is determined through chemical, thermal, and structural analysis of PU foam extrudates. The foam-to-foam extrusion process produces controllable, continuous, and uniform foam structures, as characterized by cell diameter and cell number density. Low-density PU foams are obtained through a process simulating injection molding. The compression properties of reprocessed PU foam are compared with as-synthesized PU foam to demonstrate efficacy of the refoaming processes. These results demonstrate that PU foams can be prepared through recycling while maintaining microstructural and chemical integrity. In the future, this strategy may be applied to thermoset PU foams of various chemical compositions and shows promise for scalability.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Hydrogen from low-density polyethylene via nonthermal plasma: Effects of energy density and process parameters

Nonthermal plasma processes are promising for the modular valorization of plastic waste, especially into hydrogen and carbon materials, due to their high intensity, lack of reliance on catalysts or consumables, and suitability to be directly powered by electricity. We investigate the production of hydrogen from low-density polyethylene (LDPE) as a plastic waste model using streamer Dielectric Barrier Discharge (sDBD) plasma in nitrogen at atmospheric pressure. Here, we examine the effects of process energy density (energy input per unit of feedstock mass), feedstock mass, and plasma intensity (electric voltage) on plasma properties, hydrogen yield and energy efficiency via gas chromatography, optical emission spectroscopy, and electrical diagnostics, together with reactor-scale and nonlinear electric circuit modeling. The characteristic temperature of free electrons in the sDBD plasma is approximately 15000 K (1.3 eV), and that of gas species 10 times lower, demonstrating strong thermal non-equilibrium that can lead to molecular bond scission via charged species impact rather than direct heating. Experimental results show that higher energy density leads to greater hydrogen production and diminishing energy efficiency, and that higher plasma intensity and larger feedstock mass lead to greater hydrogen yield due to higher plasma temperatures and enhanced energy fluxes to the feedstock.

08 HYDROGEN↗
DOE OSTI2025

Spatial profile of argon (1s 5 ) metastables in an electron beam generated plasma

Electron beams with an applied magnetic field generate a secondary cold plasma with a selective chemical composition, featuring low-energy ions and metastable species in the discharge periphery, ideal for low-damage plasma treatment of material substrates. In this work, we studied the plasma generated by an e-beam using a 4 kV voltage in a pure argon gas environment under a magnetic field of 150 G and in the pressure range of 25–90 mTorr. We measured the absolute spatial density profile of argon (1 s 5 ) metastables in an electron beam generated plasma by laser-induced fluorescence and found it to be of the order of 10 16 m −3 . The electron temperature and the electron density measured by a Langmuir probe were of the order of 10 16 m −3 and less than an eV respectively. Electron-impact quenching was identified as a significant loss mechanism for the Ar(1s 5 ) state, leading to the saturation of the metastable density at higher pressures. Outside the primary ionization region, the spatial distribution of argon metastables followed a linear diffusion profile, indicating negligible additional production in those regions.

EEDF↗
DOE OSTI2024

Impact of reactor architecture and design parameters on the performance of microbial electrolysis cells revealed by the electrode potential slope analysis

Microbial electrolysis cells (MECs) are appealing for recovering the chemical energy contained in domestic and industrial liquid wastes as hydrogen gas. Despite several years of research in the field, there is still a lack of critical analysis of how the reactor architecture dictates the electrochemical performance of the cell. In this study, internal resistance and onset voltage from the electrode potential slope analysis (EPS) were used in combination with current density, hydrogen production rate, reactor packing density, electrode spacing, membrane type and composition from 23 different studies to identify the reactor design parameters that primarily govern electrochemical performance of MECs. Using anion exchange membranes resulted in smaller internal resistances (AEM R int = 41± 40 mΩ m 2 ) and larger current density (18 ± 14 A m −2 ) compared to single chamber reactors (SC R int = 68 ± 58 mΩ m 2 ; 22 ± 16 A m −2 ) or MECs with cation exchange membranes (CEM R int = 376 ± 280 mΩ m 2 ; 3.0 ± 2.1 A m −2 ). Higher electrochemical performance for AEM- and SC-MECs translated in larger hydrogen gas production rates (0.122 mL H 2 C −1 for AEM vs 0.117 mL H 2 C −1 for SC), but only when inhibitors against hydrogen scavengers were added in single chamber systems (0.080 mL H 2 C −1 for SC without inhibitors). Following membrane type and composition, maintaining a small electrode spacing was the most critical parameter to improve MEC performance, indicating that the low conductivity of the media primarily limit performance by increasing ohmic resistance. Here, reactor volume and electrode surface area negatively correlated with internal resistance and current density, indicating that better performance of scaled-up reactors can likely be obtained by stacking multiple smaller units rather than just increasing reactor size. Although challenges remain in the implementation of MECs for hydrogen production from liquid wastes, advances in electrochemical engineering of the reactors can facilitate scale up and performance prediction at scale.

Electrochemistry↗