Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “High Efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

High-Efficiency, Medium-Voltage-Input, Solid-State-Transformer-Based 400-kW/1000V/400A Extreme Fast Charger for Electric Vehicles

Range anxiety and long battery charging time continue to be critical challenges to mass adaptation of EVs. A major identified gap to wider adoption of BEVs is the ability and availability to refuel quickly or to fast charge. Studies have shown that in areas where drivers have access to 50-kW or 120-kW fast charge stations, annual electric vehicle (EV) miles traveled (i.e., eVMT) increased by over 25%, even in cases where fast charging was used for 1% to 5% of total charging events. Charge stations of higher power not only alleviate the “range anxiety” and reduce the driver’s waiting time, but also requires less investment. Michigan Energy Office completed a study in early 2019 titled “Electric Vehicle Charger Placement Optimization in Michigan: Phase I – Highways”. This study finds a system with 150kW chargers, though more expensive individually, actually has lower total system cost when compared to a 50kW charging system when serving the same battery size EV. To be truly competitive to the ICEV refueling experience, even higher power stations are necessary. However, high power charge stations would create large power draws from the grid. If this occurs during peak demand periods, grid capacity could be overloaded. This problem needs to be addressed to reduce the impact on the electric utility infrastructure. The main goal of this project is to develop a 400-kW/400-A XFC system targeting total efficiency of 96.5 percent from the MVAC grid to a vehicle. The novel SST power cell topology, combined with a new silicon carbide (SiC) MOSFET device, enables a 3.5 percent improvement in system efficiency, a 50-percent smaller equipment footprint, and four times less weight than today’s DCFC systems. The SST technology would directly utilize MVAC at 4.8-kV or 13.2-kV. This would eliminate the line frequency transformer (LFT), which steps down medium-voltage AC to 3-Phase 480-V line-to-line voltage in current DCFC systems.

42 ENGINEERING↗
DOE OSTI2025

Slippery liquid infused porous surface (SLIPS) condensers for high efficiency air gap membrane distillation

Abstract To address growing water scarcity, we must improve the energy efficiency of thermal desalination technologies such as air gap membrane distillation. However, promising functional materials such as slippery liquid infused porous surfaces have not yet implemented for any desalination technology. Here, we fabricate and test slippery liquid infused porous surfaces (using Krytox 16,256 lubricant and CuO nanostructures) in an air gap membrane distillation apparatus. System-level transport models, validated by experimental data, establish a framework for improving performance through enhanced condensation surfaces. Results are obtained across a range of temperatures (50–80 °C), salinities (5–105 g/kg), and module lengths. We find that small air gap thickness and efficient droplet shedding significantly improves performance. The CuO Krytox process achieves these with a conductive-self-limiting coating, high nanostructure rugosity, strong covalent and metallic bonding, high hydrophobicity, minimal droplet pinning sites, and ultra-low contact angle hysteresis. The greatest efficiency enhancement from SLIPS is derived from the improved droplet shedding, which allows for reduced gap sizes without flooding, and is further augmented by the increased permeate flux.

Yogi, Yashwant S.↗
DOE OSTI2022

Highly efficient removal and sequestration of Cr(VI) in confined MoS 2 interlayer Nanochannels: Performance and mechanism

Environmental contamination by Cr(VI) is of particular concern because of its severe toxicity and high mobility. In this study, we employed two-dimensional MoS 2 nanosheets in the removal of Cr(VI), with an emphasis on revealing the removal mechanisms, and how the compositional and structural uniqueness of 2D MoS 2 nanomaterials intrinsically impact the Cr removal efficiency. Through batch experiments with dispersed nanosheets, we found that MoS 2 nanosheets exhibited a high Cr(VI) removal capacity at ~1100 mg/g via a phase-dependent mechanism. Particularly, the 1T polymorph in the MoS 2 nanosheets removed Cr(VI) through a redox-reaction mechanism, which was different from the adsorptive removal of Cr(VI) by MoS 2 reported previously, highlighting the compositional effects on the removal mechanism and performance. More importantly, the reduced product Cr(III) was concurrently removed via precipitation and adsorption onto the MoS 2 nanosheets, which could avoid the additional pH-elevation step that is typically needed in the conventional treatment. The unique 2D flake-like structure of MoS 2 nanosheets enabled the formation of aligned and ion-accessible nanochannels, where Cr(VI) species were accommodated, reduced and sequestered. The irreversible shrinking of the nanochannels under drying modified the interior of the layer-stacked structure into confined compartments preventing the release and re-oxidation of the immobilized Cr(III). In conclusion, the compiled results highlight the effects of MoS 2 composition and structure on the Cr removal efficiency and mechanism, which has substantial implications on future studies tailoring these unique features of 2D nanomaterials for various remediation scenarios.

42 ENGINEERING↗
DOE OSTI2022

Highly Efficient Organosulfur and Lithium‐Metal Hosts Enabled by C@Fe 3 N Sponge

Abstract Lithium‐organosulfur (Li‐OS) batteries, despite possessing high theoretical specific capacity, encounter a few practical challenges, including unsatisfactory lifespan and low active material utilization under realistic conditions. Here, diisoropyl xanthogen polysulfide (DIXPS) has been selected as a model organosulfur compound to investigate the practical feasibility of Li‐OS batteries under realistic conditions. A well‐designed freestanding carbon sponge decorated with Fe 3 N nanoparticles (C@Fe 3 N) is introduced into the Li‐OS cells as a scaffold for both Li and DIXPS. The lithiophilic property of the C@Fe 3 N host guides uniform lithium deposition at the anode, and the catalysis of the DIXPS conversion reaction promotes the kinetics at the cathode. Impressively, the synergistic effect of C@Fe 3 N leads to an extremely stable cycling performance over 1 000 cycles in a Li‐OS full cell under realistic conditions.

He, Jiarui↗
DOE OSTI2025

Late-Stage Oxidation of C( sp 3 )─H Bonds with High Efficiency and Alkyl Group Dihydroxylation of Complex Molecules

Here, the late-stage oxidation of C(sp 3 )─H bonds is highly valuable for modulating the solubility and binding of bioactive compounds and for diversification of complex molecules. Undirected methods for C(sp 3 )─H oxidation are valuable for the installation of hydroxyl groups at sites remote from other functional groups present in the molecule, but existing catalysts are limited by low turnover numbers and lengthy ligand syntheses. Perfluorinated ruthenium porphyrins are highly active catalysts for the oxidation of alkyl C─H bonds, but the scope of the transformation with complex molecules under conditions of limiting substrate has not been investigated. We report that carbonylruthenium(II) tetrakis(pentafluorophenyl)porphyrin [Ru(TPFPP)(CO)] catalyzes the selective oxidation of tertiary C(sp 3 )─H bonds in a broad range of complex natural products and drugs, with turnover numbers as high as 1000, and the tolerance of the reaction to various functional groups was rapidly assessed by performing a model reaction in the presence of additives. We show how the combination of this undirected C(sp 3 )─H oxidation and a directed C(sp 3 )─H silylation and oxidation provides rapid access to highly oxidized, 1,2-diol derivatives of natural products by a formal dihydroxylation of an alkyl group.

Alcohols↗
DOE OSTI2023

CHEETAH: Compact High Efficiency Electrically Tunable Amplifier (Abbreviated Final Report)

The goal of this project was to develop a new type of optically triggered, high speed and high power switch for radiofrequency applications with potential to exceed current state-of-the-art power and bandwidth. This device operates under a new operation principle, where discrete packets of charge carriers are generated with defined size. These are then swept out of the device at high enough fields to prevent diffusion and expansion of these packets. Individual pulse width are determined by the spatial extent of these packets and their drift velocity, which would enable control over both amplitude and frequency by control of the initial packet size, illumination intensity, and applied voltage. This effort demonstrated this new mode of operation, while uncovering a new regime of pulse compression using negative differential mobility (NDM) semiconductors such as GaAs, where the output electrical pulse is substantially shorter than the input optical pulse.

42 ENGINEERING↗
DOE OSTI2026

Aqueous electrolyte solutions with anion-bridged secondary solvation sheaths for highly efficient zinc metal batteries

Aqueous zinc metal batteries are low-cost electrochemical devices suitable for safe grid energy storage. However, water decomposition and Zn dendrite formation detrimentally affect their coulombic efficiency. Conventional aqueous electrolyte solutions, with a concentration around 1 M, are cost-effective and exhibit high bulk ionic conductivity but cannot form a stable solid electrolyte interphase. Water-in-salt and aqueous-organic hybrid electrolyte solutions can form robust solid electrolyte interphases, but they are not kinetically efficient and cost-effective. Here, to circumvent these issues, we design variously concentrated aqueous electrolyte solutions using several salts with different donor numbers to extend anion coordination into the secondary solvation sheath. We show that salt-derived anions with donor number > 18 enter the Zn2+ first solvation sheath, and ensure a strong binding energy between the Zn2+(H2O)5-anion nanometric clusters and water molecules in the secondary solvation sheath. In particular, 2 M aqueous electrolyte solutions containing fluorinated anions exhibit bulk ionic conductivities of 26-35 mS cm−1 at 25 °C and form a ZnF2-rich solid electrolyte interphase. When tested in Zn||NaV3O8·1.5H2O Swagelok cells, the best-performing electrolyte solution enables an average coulombic efficiency of 99.99% for 1,000 cycles at 1.5 mA cm−2, corresponding to an initial specific energy of 130 Wh kg−1 (based on the combined weight of the positive and negative electrodes).

25 ENERGY STORAGE↗
DOE OSTI2025

Hydrophobic Carbon Nanosheets as Passivation Layer for Perovskite Solar Cells with High Efficiency and Stability (Final Technical Report)

Hybrid organic-inorganic metal halide perovskites have continually demonstrated competitive advantages for photovoltaic applications due to their high light absorption coefficient, tunable bandgaps, ambipolar charge mobility and high tolerance of defects. However, there are many challenges yet to overcome to bring this technology to the market. For instance, bridging the ‘scaling gap’ and transitioning PSCs from a lab scale to an industrial scale is a serious challenge. This project developed a high stability and inexpensive perovskite solar cell (PSC) by incorporating hydrophobic carbon nanosheets as counter electrodes (CEs). We demonstrated that the hydrogenated carbon nanosheets with tunable hydrophobic properties as CEs can improve life-time stability of PSCs in operating conditions (i.e. humid air) while achieving impressive power conversion efficiency (PCE).

14 SOLAR ENERGY↗
DOE OSTI2022

Hydrogen generation via ammonia decomposition on highly efficient and stable Ru-free catalysts: approaching complete conversion at 450 °C

We report Hydrogen (H 2 ) is a prospective zero-carbon and high-energy-density fuel alternative to fossil fuels for generating power and clean energy. Ammonia (NH 3 ) is a promising H 2 (17.7%) carrier, which can easily overcome the challenges associated with H 2 storage and transportation. Thermocatalytic ammonia decomposition reaction (ADR) is an effective way to produce clean H 2 but it relies on the use of expensive and rare ruthenium (Ru)-based catalysts at elevated temperatures (>500 °C), hence is not sustainable and economically feasible. Herein, we report a synergistic strategy to design a heterostructured Ru-free catalyst, consisting of CoNi alloy nanoparticles well-dispersed on a MgO–CeO 2 –SrO mixed oxide support with potassium promotion. The resulting K–CoNi alloy –MgO–CeO 2 –SrO catalyst presents 97.7% and 87.5% NH 3 conversion efficiency at 450 °C at gas hourly space velocities (GHSVs) of 6000- and 12 000-mL h -1 g cat -1 , respectively. At 500 °C, the H 2 production rate (57.75 mmol g cat -1 min -1 ) becomes comparable to that of most of the reported Ru-based catalysts. The catalyst stability has been successfully demonstrated in both a fixed-bed reactor under high pressure (120 h at 5.0 bar) and a membrane reactor prototype (600 h at 1.5 bar) at 500 °C. High-temperature in situ XPS analysis, temperature-programmed desorption/reduction, and density functional theory calculations have been carried out to elucidate the possible active sites and performance enhancement mechanisms. This work highlights the importance of constructing optimal interfaces between active metal nanoparticles and oxide support for boosting the NH 3 to H 2 conversion efficiency and long-term stability.

25 ENERGY STORAGE↗
DOE OSTI2021

Highly efficient terahertz photoconductive metasurface detectors operating at microwatt-level gate powers

Despite their wide use in terahertz (THz) research and technology, the application spectra of photoconductive antenna (PCA) THz detectors are severely limited due to the relatively high optical gating power requirement. This originates from poor conversion efficiency of optical gate beam photons to photocurrent in materials with sub-picosecond carrier lifetimes. Here we show that using an ultra-thin (160 nm), perfectly absorbing low-temperature grown GaAs metasurface as the photoconductive channel drastically improves the efficiency of THz PCA detectors. This is achieved through perfect absorption of the gate beam in a significantly reduced photoconductive volume, enabled by the metasurface. This Letter demonstrates that sensitive THz PCA detection is possible using optical gate powers as low as 5 µW—three orders of magnitude lower than gating powers used for conventional PCA detectors. We show that significantly higher optical gate powers are not necessary for optimal operation, as they do not improve the sensitivity to the THz field. This class of efficient PCA THz detectors opens doors for THz applications with low gate power requirements.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Highly Efficient Organosulfur and Lithium-Metal Hosts Enabled by C@Fe 3 N Sponge

Lithium-organosulfur (Li-OS) batteries, despite possessing high theoretical specific capacity, encounter a few practical challenges, including unsatisfactory lifespan and low active material utilization under realistic conditions. Here, diisoropyl xanthogen polysulfide (DIXPS) has been selected as a model organosulfur compound to investigate the practical feasibility of Li-OS batteries under realistic conditions. A well-designed freestanding carbon sponge decorated with Fe 3 N nanoparticles (C@Fe 3 N) is introduced into the Li-OS cells as a scaffold for both Li and DIXPS. The lithiophilic property of the C@Fe 3 N host guides uniform lithium deposition at the anode, and the catalysis of the DIXPS conversion reaction promotes the kinetics at the cathode. Impressively, the synergistic effect of C@Fe 3 N leads to an extremely stable cycling performance over 1000 cycles in a Li-OS full cell under realistic conditions.

25 ENERGY STORAGE↗
DOE OSTI2022

Amorphous silicon carbide high contrast gratings as highly efficient spectrally selective visible reflectors

We report spectrally selective visible wavelength reflectors using hydrogenated amorphous silicon carbide (a-SiC:H) as a high index contrast material. Beyond 610nm and through the near infrared spectrum, a-SiC:H exhibits very low loss and exhibits an wavelength averaged index of refraction of n = 3.1. Here we design, fabricate, and characterize such visible reflectors using a hexagonal array of a-SiC:H nanopillars as wavelength-selective mirrors with a stop-band of approximately 40 nm full-width at half maximum. The fabricated high contrast grating exhibits reflectivity R >94% at a resonance wavelength of 642nm with a single layer of a-SiC:H nanopillars. The resonance wavelength is tunable by adjusting the geometrical parameters of the a-SiC:H nanopillar array, and we observe a stop-band spectral center shift from 635 nm up to 642 nm. High contrast gratings formed from a-SiC:H nanopillars are a promising platform for various visible wavelength nanophotonics applications.

Bauser, Haley C.↗
DOE OSTI2025

High-energy ion beams generated with high efficiency using laser-driven 3D microstructures

Laser-driven ion acceleration in plasma is being proposed as a source of ion beams with a high peak current that can be useful in many fields of science and medicine. Using this method, high proton energies have been achieved by increasing the laser power and by using ultrathin (≤ 200 nm) foils. However, this approach is limited by survivability of the nanotargets to laser prepulses and by difficulty in controlling the plasma acceleration properties. Here, we introduce a new target platform using two-photon polymerization, 3D laser-printed “clone” microstructures with average densities lower than solid that are relatively insensitive to the laser prepulse. Two types of microstructured targets consisting of either a multilayered log-pile or a stochastic arrangement of one micron diameter wires are used. Both demonstrate a higher energy and higher yield proton acceleration compared to thin solid-density foil targets by the robust target normal sheath acceleration (TNSA) mechanism. We find that when such 10–20 μm thick structures are irradiated with a petawatt laser, protons with energies up to 110 MeV and a laser-to-proton conversion efficiency of ~ 10% are obtained. Our work suggests that such microstructures optimized for 60–200 MeV compact proton accelerators are promising for future radiotherapy and other applications.

Physics - Plasma physics↗
DOE OSTI2022

Temperature-Following Thermal Barrier Coatings for High Efficiency Engines (Final Report)

HRL Laboratories and General Motors (GM), pursued this effort to increase the efficiency of internal combustion engines (ICEs) by developing and implementing temperature-following thermal barrier coatings (TBCs) to decrease heat loss from the combustion chamber. HRL developed microsphere TBCs based on hollow high-temperature alloy spheres with average diameter of 50 μm and wall thickness ~1 μm (microspheres) that achieve unprecedented low thermal conductivity and heat capacity (10X lower than the state of the art) while offering exceptional environmental and mechanical resistance.> In current ICEs, approximately 29% of the fuel’s energy is lost to the cooling system and about 22% goes into moving the car. By limiting heat losses from the combustion chamber with insulating coatings, fuel energy can be redirected into additional piston work and into the exhaust stream. The additional energy that goes into the exhaust stream can be turned into useful work through the use of an exhaust energy recovery device, such as turbocompounding and/or through driving a turbocharger to increase the power density of the engine allowing downsizing. Insulating coatings for piston crowns have been pursued in the past, but previous materials—typically ceramics—exhibited low thermal conductivity but retained high heat capacity. Such materials reduce heat losses but stabilize at a high surface temperature. The high surface temperature heats the incoming gases, which lowers volumetric efficiency and increases propensity for knock, resulting in degraded engine performance. This program developed an innovative new material that combines low thermal conductivity with low heat capacity. These unique properties allow it to follow rapid changes in gas temperature during each combustion cycle. A metallic microsphere TBC has been demonstrated that exhibits increased surface temperature during the combustion period, resulting in reduced heat transfer losses, while still returning to a low surface temperature during the gas exchange period. A 10X lower thermal conductivity and heat capacity than state-of-the-art thermal barrier coatings has been demonstrated. These unprecedented thermal properties are achieved through the coating architecture, which consists of closed pores on the microscale and exhibits a total porosity of 90% to 95%. By selecting a high-temperature nickel alloy as the coating material, the ductility and strength of metals can be harnessed to achieve much better durability and damage tolerance than brittle ceramic coatings can achieve.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

High-efficiency and durable optoelectronic devices using layered 2D perovskites

A thin film for an optoelectronic device includes a layered 2D perovskite material. The thin film including the layered 2D perovskite material forms a substantially or nearly single-crystalline highly uniform thin film with strongly preferential out-of-plane alignment of the inorganic perovskite layers. This single-crystalline, highly uniform, and highly aligned thin film of the layered 2D perovskite material may thereby facilitate efficient charge transport in an optoelectronic device.

14 SOLAR ENERGY↗
DOE OSTI2022

Quantum-Cutting Luminescent Coatings for High-Efficiency, Low-Cost Solar Cells (Final Technical Report)

The objective of the project is to optimize the deposition and post-deposition annealing conditions of quantum-cutting materials to enable coatings with high photoluminescence quantum yields and optimal absorption onset. These coatings will be integrated with commercial solar photovoltaic cells to enable improved power conversion efficiency, and the quantum-cutting cell stability will be ensured using industry-standard packaging methods.

14 SOLAR ENERGY↗
DOE OSTI2022

Highly efficient interface stabilization for ambient-temperature quasi-solid-state sodium metal batteries

Solid-state sodium (Na) batteries (SSSBs) using sulfide-based solid electrolytes (SSEs) hold tremendous promise due to their high theoretical specific capacity, enhanced safety and abundant resources. However, detrimental interfacial issues between SSEs and Na metal present a major challenge to the advancement of sulfide-based SSSBs. To address interfacial issues, we demonstrate an efficient approach by incorporating an ionic liquid electrolyte ((PYR/Na)TFSI) as interlayer to stabilize the Na metal/SSE interface. The presence of the (PYR/Na)TFSI interlayer enables the formation of a stable solid electrolyte interphase (SEI) to prevent the harmful reactions and inhibit Na dendrites. Combination of ab initio molecular dynamics simulations and X-ray photoelectron spectroscopy revealed that this stable SEI is largely composed of reduced products of TFSI -, such as NaF and CF 3 . As a result, the symmetric cells exhibited stable Na plating/striping cycling for 300 h at 0.1 mA cm -2 . In addition, FeS2||Na quasi-solid-state batteries delivered an impressive specific capacity of over 300 mAh g -1 under the current density of 20 mA g -1 at room temperature. Under a higher current density (100 mA g -1 ), such batteries performed with long-term cycling stability and maintained a specific capacity of around 103 mAh g -1 after 330 cycles. This work demonstrates the novel perspective of using an ionic liquid interlayer to address interfacial issues, contributing to the advancement of high-performance SSSBs for the next-generation energy storage systems.

25 ENERGY STORAGE↗
DOE OSTI2020

Highly efficient non-fullerene organic solar cells enabled by a delayed processing method using a non-halogenated solvent

The use of non-halogenated solvents is one of the important requirements for large-scale industry production of polymer solar cells (PSCs). However, the current high-performance PSCs are mostly obtained using halogenated solvents to ensure good solubility and morphology. In this work, we report high-performance PSCs processed using a halogen-free solvent (toluene), reaching an efficiency of 17.33%, which, to the best of our knowledge, is the highest value reported for PSCs processed from non-halogenated solvents. Importantly, we show a novel aggregation or “aging” process of the non-fullerene acceptor in the toluene solvent, which can be used to fine-tune the crystal size of the non-fullerene acceptor. As a result, we achieve an optimized nano-fibril like morphology of PM6:BTP-BO-4Cl by delaying the processing time. Furthermore ,this is conducive to charge dissociation and transport, and thus greatly improved device performance. This method is expected to be investigated further and applied to other PSC systems toward precise morphology optimization and performance improvements in the future.

36 MATERIALS SCIENCE↗