Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EVAPORATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2012

Desiccant Enhanced Evaporative Air Conditioning: Parametric Analysis and Design; Preprint

This paper presents a parametric analysis using a numerical model of a new concept in desiccant and evaporative air conditioning. The concept consists of two stages: a liquid desiccant dehumidifier and a dew-point evaporative cooler. Each stage consists of stacked air channel pairs separated by a plastic sheet. In the first stage, a liquid desiccant film removes moisture from the process(supply-side) air through a membrane. An evaporatively-cooled exhaust airstream on the other side of the plastic sheet cools the desiccant. The second-stage indirect evaporative cooler sensibly cools the dried process air. We analyze the tradeoff between device size and energy efficiency. This tradeoff depends strongly on process air channel thicknesses, the ratio of first-stage to second-stagearea, and the second-stage exhaust air flow rate. A sensitivity analysis reiterates the importance of the process air boundary layers and suggests a need for increasing airside heat and mass transfer enhancements.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Monitoring Warm Wastewater and Evaporation Fans - A Brilliant Duo

The Advanced Test Reactor (ATR) generates warm wastewater which must be stored in warm wastewater ponds. The goal is to evaporate the water from the ponds and using evaporation fans may help to accomplish this. This project explores how much water has been accumulated into the ponds along with how much water has been entering and leaving the ponds over the past 5 years. Furthermore, the implementation of the evaporation fans into the ponds is evaluated to see if they are helpful for improving evaporation rates or not.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Mixed-state entanglement and information recovery in thermalized states and evaporating black holes

We study the universal behavior of quantum information-theoretic quantities in thermalized isolated quantum many-body systems and evaporating black holes. In particular, we study a genuine mixed-state entanglement measure called the logarithmic negativity, other correlation measures including the Renyi negativities and the mutual information, and a signature of multipartite entanglement called the reflected entropy. We also probe the feasibility of recovering quantum information from subsystems of a thermalized quantum many-body system or from the radiation of an evaporating black hole, using quantities such as relative entropy and Petz map fidelity. A recently developed technique called the equilibrium approximation allows us to probe these quantities at finite temperature. We find striking qualitative differences from the infinite temperature case, which has been the topic of previous studies using Haar-random states. In particular, we find regimes where the logarithmic negativity is extensive but the mutual information is sub-extensive, indicating a large amount of undistillable, bound entanglement in thermalized states. For evaporating black holes at finite temperature, both the logarithmic negativity and the Petz map fidelity reveal an important new time scale t b , which is earlier than the Page time t p by a finite fraction of the total evaporation time. We find that t b , as opposed to t p , is the time scale at which quantum entanglement between different parts of the radiation becomes extensive, and the fidelity of information recovery for a large diary thrown into the black hole starts to grow.

2D Gravity↗
DOE OSTI2021

Replica wormholes for an evaporating 2D black hole

Quantum extremal islands reproduce the unitary Page curve of an evaporating black hole. This has been derived by including replica wormholes in the gravitational path integral, but for the transient, evaporating black holes most relevant to Hawking’s paradox, these wormholes have not been analyzed in any detail. In this paper we study replica wormholes for black holes formed by gravitational collapse in Jackiw-Teitelboim gravity, and confirm that they lead to the island rule for the entropy. The main technical challenge is that replica wormholes rely on a Euclidean path integral, while the quantum extremal islands of an evaporating black hole exist only in Lorentzian signature. Furthermore, the Euclidean equations for the Schwarzian mode are non-local, so it is unclear how to connect to the local, Lorentzian dynamics of an evaporating black hole. We address these issues with Schwinger-Keldysh techniques and show how the non-local equations reduce to the local ‘boundary particle’ description in special cases.

2D gravity↗
DOE OSTI2020

Simple holographic models of black hole evaporation

Several recent papers have shown a close relationship between entanglement wedge reconstruction and the unitarity of black hole evaporation in AdS/CFT. The analysis of these papers however has a rather puzzling feature: all calculations are done using bulk dynamics which are essentially those Hawking used to predict information loss, but applying ideas from entanglement wedge reconstruction seems to suggest a Page curve which is consistent with information conservation. Why should two different calculations in the same model give different answers for the Page curve? In this note we present a new pair of models which clarify this situation. Our first model gives a holographic illustration of unitary black hole evaporation, in which the analogue of the Hawking radiation purifies itself as expected, and this purification is reproduced by the entanglement wedge analysis. Moreover a smooth black hole interior persists until the last stages the evaporation process. Our second model gives an alternative holographic interpretation of the situation where the bulk evolution leads to information loss: unlike in the models proposed so far, this bulk information loss is correctly reproduced by the entanglement wedge analysis. This serves as an illustration that quantum extremal surfaces are in some sense kinematic: the time-dependence of the entropy they compute depends on the choice of bulk dynamics. In both models no bulk quantum corrections need to be considered: classical extremal surfaces are enough to do the job. We argue that our first model is the one which gives the right analogy for what actually happens to evaporating black holes, but we also emphasize that any complete resolution of the information problem will require an understanding of non-perturbative bulk dynamics.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2018

Effect of Rotary Evaporator Water Bath Temperature on Recovery Rate of Phthalate Esters

To clarify the influence of water bath temperature on the decompression and concentration efficiency of a rotary evaporator, accurate control of the water bath temperature is required. Therefore, the water bath temperature control system of a rotary evaporator was studied using the recovery rate of phthalate esters (PAEs) as the indicator. The results showed that when the temperature of the rotary evaporator was set at 40°C, the actual temperature range of the concentrated liquid would change from 26–41 to 39–41°C. By modifying the water bath temperature control system, the recovery rate of PAEs could be increased from 72.4% to 85.6% to 93.2%–98.5%. This test indicates that temperature has a great influence on vacuum concentration, and the recovery rate of PAEs can be improved by modifying the water bath temperature control system used in the rotary evaporator.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2019

Characterization and numerical simulation of liquid refrigerant R-134a flow emerging from a flooded evaporator tube bundle

The distribution of liquid droplets emerging from an evaporator tube bundle is characterized for refrigerant R-134a with a triangular tube arrangement with a pitch of 1.167. The purpose of this research was to improve understanding of the droplet ejection process to aid in design of evaporators typically used in larger chiller systems. A laser and camera system captured images of the evaporator headspace at varying conditions. Conventional shadowgraphy techniques were applied to recognize and match droplets for velocity calculations. The evaporator conditions varied with bundle mass fluxes of 20.3 and 40.7 kg s -1 m -2 , top-rows heat fluxes of 15.8 and 31.5 kWm -2 , and outlet saturation temperatures of 4.4 and 12.8 °C. Conditions ranged from flooded to dryout of the top rows. Droplet number, size distribution, velocity, and liquid volume fraction are presented in the headspace above the bundle. A method to numerically duplicate the droplet loading in the headspace using CFD with a Lagrangian discrete-phase model is also presented and verified, providing a powerful design tool. Liquid distribution in the headspace is found to be a strong function of all varied properties, particularly mass flux, liquid level, and saturation temperature

42 ENGINEERING↗
DOE OSTI2019

Quarkonium Production and Polarization in an Improved Color Evaporation Model

An improved version of the color evaporation model (ICEM) has been introduced to describe heavy quarkonium production. In contrast to the traditional color evaporation model, the constraint was imposed that the invariant mass of the intermediate heavy quark-antiquark pair must be larger than the mass of produced quarkonium. A momentum shift between heavy quark-antiquark pair and the quarkonium was also introduced. Calculations show that the model can describe the charmonium yields as well as ratio of $\psi$' over $J$/$\psi$ better than the traditional color evaporation model. The ICEM has been extended to calculate the polarization of prompt $J$/$\psi$ and $Υ$($1S$) production for the first time in the color evaporation approach. The first calculations were made at leading order. The polarization parameter λ$_\vartheta$ was calculated as a function of center of mass energy and rapidity in p + p collisions. The x F dependence of the polarization was also calculated and compred to experimental results in p+Cu and π+W collisions. The next step of calculating the p T dependence of the polarization has been taken, with a calculation in the k T -factorization approach. We compare the unpolarized p T distributions for the $J$/$\psi$ and $\psi$, as well as the $\psi$ to $J$/$\psi$ ratio, in p + p collisions at RHIC and the LHC for several energies. We also present the polarization results and make comparison to polarization data.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

Thin-Film Solar Cells with 19% Efficiency by Thermal Evaporation of CdSe and CdTe

CdTe-based solar cells exhibiting 19% power conversion efficiency were produced using widely available thermal evaporation deposition of the absorber layers on SnO2-coated glass with or without a transparent MgZnO buffer layer. Evaporating CdSe and CdTe sequentially by thermal evaporation and subsequent CdCl2 annealing establishes efffective CdSeTe band grading as well as dense, large-grain films. These results show that high-performance II-VI photovoltaics can be made by inexpensive, commercially available evaporation systems without the need to build customized equipment, enabling CdTe photovoltaics research and manufacturing to be more accessible to the broader photovoltaics community.

14 SOLAR ENERGY↗
DOE OSTI2018

Experimental Testing Scale Considerations for the Investigation of Bare‐Soil Evaporation Dynamics in the Presence of Sustained Above‐Ground Airflow

Abstract At the fundamental process level, many of the concepts that form the foundation of our understanding of bare‐soil evaporation dynamics have advanced little since their initial formation. This investigation explores experimental scaling issues that should be considered during the study of bare‐soil evaporation dynamics under conditions of sustained above‐ground airflow. Results are presented from a series of large‐scale laboratory experiments conducted for various soil conditions (i.e., heterogeneity and surface roughness). Fundamental experimental research of this nature is not feasible in the field or small laboratory columns that are limited by system control and scale. All experimentation was therefore conducted in a test facility that couples a climate‐controlled, low‐speed wind tunnel with a 7.15‐m‐long soil tank—allowing for control over soil properties and initial and boundary conditions. Measured flow phenomena supported, and agreed well with, existing wind tunnel and field study literature. These data were in turn, used to explain observed evaporative water loss and soil moisture distribution spatiotemporal trends and patterns. Results demonstrated that relatively large length scales are required for the impacts of atmospheric feedbacks on the subsurface hydrodynamics to manifest themselves and become quantifiable. Airflow had the greatest impact in the case of a flat homogeneous soil; the strength of this feedback was significantly weaker in the presence of soil heterogeneities and surface undulations that were dominated by other transport phenomena. Comparison of these results with those of past studies furthermore cautions against the use of column scale data to make generalizations about bare‐soil evaporation dynamic upscaling.

Trautz, Andrew C.↗
DOE OSTI2020

Climate change will affect global water availability through compounding changes in seasonal precipitation and evaporation

Both seasonal and annual mean precipitation and evaporation influence patterns of water availability impacting society and ecosystems. Existing global climate studies rarely consider such patterns from non-parametric statistical standpoint. Here, we employ a non-parametric analysis framework to analyze seasonal hydroclimatic regimes by classifying global land regions into nine regimes using late 20th century precipitation means and seasonality. These regimes are used to assess implications for water availability due to concomitant changes in mean and seasonal precipitation and evaporation changes using CMIP5 model future climate projections. Out of 9 regimes, 4 show increased precipitation variation, while 5 show decreased evaporation variation coupled with increasing mean precipitation and evaporation. Increases in projected seasonal precipitation variation in already highly variable precipitation regimes gives rise to a pattern of “seasonally variable regimes becoming more variable”. Regimes with low seasonality in precipitation, instead, experience increased wet season precipitation.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2018

Modeling solvent evaporation during thin film formation in phase separating polymer mixtures

Preparation of thin films by dissolving polymers in a common solvent followed by evaporation of the solvent has become a routine processing procedure. However, modeling of thin film formation in an evaporating solvent has been challenging due to a need to simulate processes at multiple length and time scales. In this paper, we present a methodology based on the principles of linear non-equilibrium thermodynamics, which allows systematic study of various effects such as the changes in the solvent properties due to phase transformation from liquid to vapor and polymer thermodynamics resulting from such solvent transformations. The methodology allows for the derivation of evaporative flux and boundary conditions near each surface for simulations of systems close to the equilibrium. We apply it to study thin film microstructural evolution in phase segregating polymer blends dissolved in a common volatile solvent and deposited on a planar substrate. Finally, effects of the evaporation rates, interactions of the polymers with the underlying substrate and concentration dependent mobilities on the kinetics of thin film formation are studied.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Solar-driven evaporators for water treatment: challenges and opportunities

Solar-driven evaporation is an emerging process to acquire freshwater from saline water or wastewater, in which photothermal materials play a crucial role. Additionally, significant effort has been devoted to promoting energy conversion efficiency by material and device design. In the current review, we discuss the major factors affecting evaporator efficiency and long-term performance, including selection of photothermal materials, promotion of evaporation efficiency, and solutions to the problem of scaling. Both the material components and structure will affect the absorption and reflection of the incident light, and the evaporation efficiency can be enhanced by reducing heat loss, enlarging surface area, and recycling latent heat. Scaling can be addressed by tailoring surface properties and structure.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Mass spectral molecular mapping shows benefits of thermal evaporation in prelithiated silicon-based electrodes

Silicon based composites have become increasingly popular as potential anodes for lithium-ion batteries due to their large storage capacity and potential ability to generate batteries with energy densities greater than 350 Wh kg −1 . These anodes often see reduced initial columbic efficiency (ICE) due to disruptive volume expansionup to 300% and continuous solid electrolyte interphase (SEI) layer formation. Prelithiation, where an excess reservoir of Li is added to the electrode to compensate for irreversible SEI formation losses during their sample preparation, has proven to solve the issue of immediate capacity loss. Thermal evaporation is a prelithiation technique with limited studies on its effectiveness. In this study, time-of-flight secondary ion mass spectrometry (ToF-SIMS) is used to highlight the benefits of prelithiation via thermal evaporation. ToF-SIMS provides chemical mapping and spatial information in 2D and 3D visualizing the deposition of lithium, identifying Li x Si y alloy and Li x Si y O z silicate formation, and the distribution of lithium passivation into the electrodes. Passivation under different atmospheric conditions, such as inert Argon (Ar) and Ar/ carbon dioxide (CO 2 ), highlights the impact of the environment on the passivation effectiveness and formation of Li x Si y alloy and Li x Si y O z silicate. The ToF-SIMS molecular imaging and depth profiling results indicate that prelithiation via thermal evaporation effectively distributes lithium throughout the depth profile thickness of several hundred nanometers. It induces a greater degree of Li x Si y O z silicate formation over Li x Si y alloy. Our ToF-SIMS characterization results show the effectiveness of thermal evaporation in producing a more stable electrode and an electrode with an effective lithium reserve that can preserve its capacity.

Parker, Gabriel D. [Oak Ridge National Laboratory ↗
DOE OSTI2013

Molecular dynamics simulations of evaporation-induced nanoparticle assembly

While evaporating solvent is a widely used technique to assemble nano-sized objects into desired superstructures, there has been limited work on how the assembled structures are affected by the physical aspects of the process. We present large scale molecular dynamics simulations of the evaporation-induced assembly of nanoparticles suspended in a liquid that evaporates in a controlled fashion. The quality of the nanoparticle crystal formed just below the liquid/vapor interface is found to be better at relatively slower evaporation rates, as less defects and grain boundaries appear. This trend is understood as the result of the competition between the accumulation and diffusion times of nanoparticles at the liquid/vapor interface. When the former is smaller, nanoparticles are deposited so fast at the interface that they do not have sufficient time to arrange through diffusion, which leads to the prevalence of defects and grain boundaries. Our results have important implications in understanding assembly of nanoparticles and colloids in non-equilibrium liquid environments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2015

Field evaporation of ZnO: A first-principles study

With recent advances in atom probe tomography of insulators and semiconductors, there is a need to understand high electrostatic field effects in these materials as well as the details of field evaporation. We use density functional theory to study field effects in ZnO clusters calculating the potential energy curves, the local field distribution, the polarizability, and the dielectric constant as a function of field strength. We confirm that, as in MgO, the HOMO-LUMO gap of a ZnO cluster closes at the evaporation field strength signaling field-induced metallization of the insulator. Following the structural changes in the cluster at the evaporation field strength, we can identify the field evaporated species, in particular, we show that the most abundant ion, Zn{sup 2+}, is NOT post-ionized but leaves the surface as 2+ largely confirming the experimental observations. Our results also help to explain problems related to stoichiometry in the mass spectra measured in atom probe tomography.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Transmission interference fringe ( TIF ) technique for the dynamic visualization of evaporating droplet

Here, the transmission interference fringe (TIF) technique was developed to visualize the dynamics of evaporating droplets based on the Reflection Interference Fringe (RIF) technique for micro-sized droplets. The geometric formulation was conducted to determine the contact angle (CA) and height of macro-sized droplets without the need for the prism used in RIF. The TIF characteristics were analyzed through experiments and simulations to demonstrate a wider range of contact angles from 0 to 90°, in contrast to RIF's limited range of 0–30°. TIF was utilized to visualize the dynamic evaporation of droplets in the constant contact radius (CCR) mode, observing the droplet profile change from convex-only to convex-concave at the end of dry-out from the interference fringe formation. The TIF also observed the contact angle increase from the fringe radius increase. This observation is uniquely reported as the interference fringe (IF) technique can detect the formation of interference fringe between the reflection from the center convex profile and the reflection from the edge concave profile on the far-field screen. Unlike general microscopy techniques, TIF can detect far-field interference fringes as it focuses beyond the droplet-substrate interface. The formation of the convex-concave profile during CCR evaporation is believed to be influenced by the non-uniform evaporative flux along the droplet surface.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Evaporation barrier for dark matter in celestial bodies

The minimum testable dark matter (DM) mass for almost all DM signatures in celestial bodies is determined by the rate at which DM evaporates. DM evaporation has previously been calculated assuming a competition between the gravitational potential of the object, and thermal kicks from the celestial-body matter. We point out a new effect, where mediators with a range larger than the interparticle spacing induce a force proportional to the density gradient of celestial objects, forming an evaporation barrier for the DM. This effect can be so significant that evaporation does not occur even for sub-MeV DM, in stark contrast to previous calculations. This opens up a wide range of new light DM searches, many orders of magnitude in DM mass below the sensitivity of direct detection.

79 ASTRONOMY AND ASTROPHYSICS↗