Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Modelling the deployment of CO₂ storage in U.S. gas-bearing shales

The proliferation of commercial development in U.S. gas-bearing shales helped to drive a twelve-fold increase in domestic gas production between 2000 and 2010, and the nation's gas production rates continue to grow. While shales have long been regarded as a desirable caprock for CCS operations because of their low permeability and porosity, there is increasing interest in the feasibility of injecting CO₂ into shales to enhance methane recovery and augment CO₂ storage. Laboratory work published in recent years observes that shales with adsorbed methane appear to exhibit a stronger affinity for CO₂ adsorption, offering the potential to drive additional CH₄ recovery beyond primary production and perhaps the potential to store a larger volume of CO₂ than the volume of methane displaced. Recent research by the authors on the revenues associated with CO₂-enhanced gas recovery (CO₂-EGR) in gas-bearing shales estimates that, based on a range of EGR response rates, the average revenue per ton of CO₂ for projects managed over both EGR and subsequent storage-only phases could range from $0.50 to $18/tCO₂. While perhaps not as profitable as EOR, for regions where lower-cost storage options may be limited, shales could represent another “early opportunity” storage option if proven feasible for reliable EGR and CO₂ storage. Significant storage potential exists in gas shales, with theoretical CO₂ storage resources estimated at approximately 30-50 GtCO₂. However, an analysis of the comprehensive cost competitiveness of these various options is necessary to understand the degree to which they might meaningfully impact U.S. CCS deployment or costs. This preliminary analysis shows that the degree to which EGR-based CO₂ storage could play a role in commercial-scale deployment is heavily dependent upon the offsetting revenues associated with incremental recovery; modeling the low revenue case resulted in only five shale-based projects, while under the high revenue case, shales accounted for as much as 20 percent of total U.S. storage in the first 20 years of deployment. Interestingly, even in this highest revenue case, there appear to be no negative-cost projects that would be profitable in a no-policy environment as modeled under the assumptions employed. While this reflects a very first look at the potential for shales, it is clear that more laboratory and experimental work are needed to reduce uncertainty in key variables and begin to differentiate and identify high-potential shales for early pilot study.

54 ENVIRONMENTAL SCIENCES↗

Early opportunities of CO₂ geological storage deployment in coal chemical industry in China

Carbon dioxide capture and geological storage (CCS) is regarded as a promising option for climate change mitigation; however, the high capture cost is the major barrier to large-scale deployment of CCS technologies. High-purity CO₂ emission sources can reduce or even avoid the capture requirements and costs. Among these high-purity CO₂ sources, certain coal chemical industry processes are very important, especially in China. In this paper, the basic characteristics of coal chemical industries in China is investigated and analyzed. As of 2013 there were more than 100 coal chemical plants in operation. These emission sources together emit 430 million tons CO₂ per year, of which about 30% are emit high-purity and pure CO₂ (CO₂ concentration >80% and >98.5% respectively). Four typical source-sink pairs are chosen for techno-economic evaluation, including site screening and selection, source-sink matching, concept design, and economic evaluation. The technical-economic evaluation shows that the levelized cost of a CO₂ capture and aquifer storage project in the coal chemistry industry ranges from 14 USD/t to 17 USD/t CO₂. When a 15USD/t CO₂ tax and 20USD/t for CO₂ sold to EOR are considered, the levelized cost of CCS project are negative, which suggests a benefit from some of these CCS projects. This might provide China early opportunities to deploy and scale-up CCS projects in the near future.

54 ENVIRONMENTAL SCIENCES↗

Interpretation of Tracer Experiments on Inverted Five-spot Well-patterns within the Western Half of the Farnsworth Unit Oil Field

The Southwest Carbon Partnership (SWP), one of the U.S. Department of Energy (U.S. DOE) seven Regional Carbon Sequestration Partnerships, is currently working to demonstrate the utilization and storage of CO 2 in the Farnsworth Unit (FWU) Enhanced Oil Recovery (EOR) site under the final development phase of this U.S. DOE initiative. A component of the research is to use fluid tracers to understand the multifluid flow patterns that develop between injection and production wells via collected field data and supporting numerical reservoir models. The FWU, located in the Anadarko Basin, Ochiltree County, Texas, and being operated by Chaparral Energy, is a mature EOR water-flood field, which is currently being converted to a CO 2 flow, with inverted 5-spot patterns transitioning from pure water to alternating CO 2 and water floods (i.e., water alternating gas (WAG)) at an approximate rate of one every 6 to 10 months. The SWP tracer program is conducting a suite of tracer injections into the active 5-spot patterns at the FWU. Tracers have been selected to be nonreactive and either principally soluble in CO 2 (gas soluble) or water (aqueous soluble). In addition to characterizing the multifluid flow behaviour within reservoir, the gas and aqueous tracers have roles in detecting any leakage from the reservoir. A total of seven unique perfluorocarbon tracer (PFT) compounds make up the suite of gas soluble tracers and eight unique naphthalene sulfonate tracer (NPT) compounds comprise the aqueous soluble tracers. Lastly, all selected tracers are significantly detectable below the parts per billion concentrations, allowing for high resolution for the inter-well tests at relatively low injection volumes.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

CO 2 Sequestration and Enhanced Oil Recovery at Depleted Oil/Gas Reservoirs

This study presents a quantitative evaluation of the operational and technical risks of an active CO 2 -EOR project. A set of risk factor metrics is defined to post-process the Monte Carlo (MC) simulations for statistical analysis. The risk factors are expressed as measurable quantities that can be used to gain insight into project risk (e.g. environmental and economic risks) without the need to generate a rigorous consequence structure, which include (a) CO 2 injection rate, (b) net CO 2 injection rate, (c) cumulative CO 2 storage, (d) cumulative water injection, (e) oil production rate, (f) cumulative oil production, (g) cumulative CH 4 production, and (h) CO 2 breakthrough time. The Morrow reservoir at the Farnsworth Unit (FWU) site, Texas, is used as an example for studying the multi-scale statistical approach for CO 2 accounting and risk analysis. A set of geostatistical-based MC simulations of CO 2 -oil/gas-water flow and transport in the Morrow formation are conducted for evaluating the risk metrics. A response-surface-based economic model has been derived to calculate the CO 2 -EOR profitability for the FWU site with a current oil price, which suggests that approximately 31% of the 1000 realizations can be profitable. If government carbon-tax credits are available, or the oil price goes up or CO 2 capture and operating expenses reduce, more realizations would be profitable.

02 PETROLEUM↗

Pore-scale flow characterization of low-interfacial tension flow through mixed-wet porous media with different pore geometries

The low-interfacial tension flow through porous media occurs in surfactant-based enhanced oil recovery (EOR), soil clean-up, underground removal of the non-aqueous phase liquid and dense non-aqueous phase liquid, etc. In surfactant-based EOR processes, numerous works have been carried out to characterize - either qualitatively or quantitatively - the micro- and macro-scale flow behavior. What has been lacking is to link the statistics of oil blobs population (e.g., distribution of blob length and diameter) to the pore-scale phenomena and macro-scale quantities. In particular, no work has been reported to elucidate the effect of the ratio of pore body to throat diameter (i.e., aspect ratio) on the pore-scale characterization based on the blobs population statistics. The significance of the aspect ratio lies in that it describes the geometry of a porous medium and is one of the foremost morphological features. The aspect ratio is also one of the fundamental factors governing the pore-level events. This study presents the effect of aspect ratio on the statistical distribution of the blob length and equivalent diameter and links the blobs population statistics to the observed pore-level events. The pore-scale variation of the ratio of viscous-to-capillary forces acted on the oil blobs at the threshold of displacement is utilized to characterize the effect of blob length distribution at different aspect ratios. It also provides some insight into correlating the change in oil recovery efficiency and capillary number, by change in aspect ratio, with the change in blobs population statistics. (author)

02 PETROLEUM↗

Application of mixed kernels function (MKF) based support vector regression model (SVR) for CO 2 – Reservoir oil minimum miscibility pressure prediction

Carbon dioxide (CO 2 ) injection into oil reservoirs is considered a mature enhanced oil recovery (EOR) technique for conventional reservoirs. The local displacement efficiency of the CO 2 -EOR process is highly dependent on the minimum miscibility pressure (MMP), estimating this parameter is critical to design of the CO 2 injection process. Traditional empirical methods to test the CO 2 -oil MMP are time consuming and expensive; derived correlations are fast but not accurate. Therefore, an efficient and reliable method to determine MMP is beneficial. Here in this study, a mixed kernels function (MKF) based support vector regression (SVR) model was developed and used to predict the MMP for both pure and impure CO 2 injection cases. Four parameters were chosen as input parameters: (1) reservoir temperature; (2) average critical temperature; (3) molecular weight of pentane plus (C 5+ ) fraction of crude oil, and; (4) the ratio of volatile components to intermediate components in crude oil. MMP was selected as the desired output parameter to train and test this newly developed model. The performance of basic kernels function based SVR model is compared with that of this newly developed MKF-SVR model. The well-trained MFK-SVR was compared with three well-established published correlations, demonstrated the highest correlation coefficient (R of 0.9381), lowest root mean square error (RMSE of 1.9151), smallest average absolute error (AAE of 1.1406) and maximum absolute error (MAE of 4.6291). We believe that the proposed MFK-SVM model is a more reliable and stable regression model to predict MMP. In addition, a sensitivity analysis was conducted to evaluate the physical correctness. It indicates that the predicted results from the newly developed model are in excellent agreement with previous empirical work.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Differential retention and release of CO 2 and CH 4 in kerogen nanopores: Implications for gas extraction and carbon sequestration

Methane (CH 4 ) and carbon dioxide (CO 2 ), the two major components generated from kerogen maturation, are stored dominantly in nanometer-sized pores in shale matrix as (1) a compressed gas, (2) an adsorbed surface species and/or (3) a species dissolved in pore water (H 2 O). In addition, supercritical CO 2 has been proposed as a fracturing fluid for simultaneous enhanced oil/gas recovery (EOR) and carbon sequestration. A mechanistic understanding of CH 4 -CO 2 -H 2 O interactions in shale nanopores is critical for designing effective operational processes. Using molecular simulations, we show that kerogen preferentially retains CO 2 over CH 4 and that the majority of CO 2 either generated during kerogen maturation or injected in EOR will remain trapped in the kerogen matrix. The trapped CO 2 may be released only if the reservoir pressure drops below the supercritical CO 2 pressure. When water is present in the kerogen matrix, it may block CH 4 release. Furthermore, the addition of CO 2 may enhance CH 4 release because CO 2 can diffuse through water and exchange for adsorbed methane in the kerogen nanopores.

03 NATURAL GAS↗

A multi-criteria CCUS screening evaluation of the Gulf of Mexico, USA

Continued research into reservoir characterization along with offshore carbon dioxide (CO 2 ) transportation and infrastructure assets is needed to facilitate development of safe and successful carbon capture, utilization, and storage (CCUS) projects. This paper outlines a multi-criteria evaluation methodology that incorporates disparate sets of quantitative, spatially variable data into a decision-making framework for screening the Gulf of Mexico (GOM) outer continental shelf (OCS) for potentially viable CO 2 storage and enhanced oil recovery (EOR) sites. Criteria categories include favorable geologic characteristics, logistics, and potential risks. Data compiled for 14 criteria from several publicly available geographic information system (GIS) layers was aggregated over 2559 spatially balanced points across the study area using the National Energy Technology Laboratory (NETL)-developed Cumulative Spatial Impact Layers™ (CSIL) GIS tool. Criteria are weighted by qualitative expert opinion relative to their perceived importance to given scenarios— the output of combined criteria values and weights enables regional CO 2 storage suitability differentiation. The methodology considers both technical and non-technical factors impacting CCUS decision-making. The flexible methodology enables a systematic approach to regional ranking at high spatial resolution over a large study domain. Additionally, the framework enables high-grading of priority sites that warrant further characterization and follow-on analysis. Areas along the Louisiana coast and Mississippi River Delta consistently rank high for all scenarios largely a result of the favorable geology with the potential for stacked storage, as well as the density of existing pipelines and platforms, and proximity to several onshore CO 2 sources. High-graded regions for the CO 2 EOR-related scenarios are typically located further offshore towards the middle and edge of the OCS compared to higher priority regions for the geologic storage scenarios which fall closer to the Louisiana coastline.

54 ENVIRONMENTAL SCIENCES↗

Nuclear reaction analysis of helium migration in silicon carbide

4H-SiC and 6H-SiC single crystals were implanted at room temperature with 3-MeV 3He ions at a fluence of 1x1016 cm-2. Analysis of helium migration was carried out with the 3He(d, p)4He nuclear reaction. No clear thermally-activated migration in the end-of-range (EOR) region is found below 1100 C, meaning that helium is strongly trapped probably in helium-vacancy clusters. At 1100 C and above, a fraction of 3He atoms remains trapped in the clusters, but a significant fraction is detrapped into a broad distribution, which is slightly shifted towards the sample surface. Helium detrapping from the EOR region increases with increasing annealing time and temperature. Moreover, the helium content is not conserved, since a significant fraction of 3He atoms is released out of the sample. Helium out-gassing actually increases with increasing annealing time and temperature, up to about 40% at 1150 C. No clear difference is found between the 4H-SiC and 6H-SiC polytypes.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Rational design of septenary high-entropy alloy for direct ethanol fuel cells

Promoting C–C bond cleavage of ethanol by a complete 12-electron (12e) ethanol oxidation reaction (EOR) is a grand challenge for the development of highly efficient direct ethanol fuel cells (DEFCs). Most state-of-the-art catalysts only implement the EOR in an incomplete 4e or 2e pathway because of the poisoning of the catalysts by strongly adsorbed CO, leading to the poor output performance and low cell efficiency of DEFCs. Herein, a septenary PtPdFeCoNiSnMn high-entropy alloy (PtPd HEA) with a PtPd-rich surface but super-low platinum group metals loading was developed. We identified and proved the functions of each element in the PtPd HEA. The DEFCs assembled with the PtPd HEA (0.12 mg PtPd ∙cm -2 ) achieved a maximum power density of 0.72 W cm -2 and a durable operation for 1,200 h, which outperforms state-of-the-art catalysts for DEFCs. This work will be a design principle for nanostructured alloy development for renewable energy and sustainability applications.

25 ENERGY STORAGE↗

Capacity assessment and co-optimization of CO 2 storage and enhanced oil recovery in residual oil zones

Residual oil zones (ROZs) are increasingly being commercially exploited using CO 2 -enhanced oil recovery (CO 2 -EOR) method. In this study, CO 2 storage potential, long-term CO 2 fate and oil recovery potential in ROZs are characterized based on a reservoir model for Goldsmith-Landreth San Andres Unit in the Permian Basin. The effects of CO 2 injection rates, well patterns (five-spot and line-drive), well spacings, injection modes (continuous CO 2 injection and water-alternatinggas injection) on the CO 2 retention in the reservoir and the oil production are investigated. After the preliminary assessment of CO 2 storage and EOR potentials in ROZs, we next develop a novel approach based on a newly developed optimization algorithm-Stochastic Simplex Approximate Gradient (StoSAG) and predictive empirical models constructed using machine learning technique to co-optimize CO 2 storage and oil recovery in ROZs. The performance of co-optimization of CO 2 storage and oil recovery is compared with the performance of optimization of only CO 2 storage.

58 GEOSCIENCES↗

Ultrathin Pt x Sn 1–x Nanowires for Methanol and Ethanol Oxidation Reactions: Tuning Performance by Varying Chemical Composition

Pt-based alloys denote promising catalysts for the methanol oxidation reaction (MOR) and the ethanol oxidation reaction (EOR), due to their enhanced activity toward alcohol-oxidation reactions and reduced cost as compared with Pt alone. Among all of these binary systems, PtSn has been reported to exhibit superior methanol/ethanol oxidation activity. In this paper, we deliberatively tailor chemical composition, reduce size, and optimize morphology of the catalyst in an effort to understand structure–property correlations that can be used to improve upon the electrocatalytic activity of these systems. Previous work performed by our group suggested that Pt-based catalysts, possessing an ultrathin one-dimensional (1D) structure, dramatically promote both cathodic and anodic reactions with respect to their zero-dimensional (0D) counterparts. Herein, a novel set of ultrathin binary Pt–Sn 1D nanowire (NW) catalysts with rationally controlled chemical compositions, i.e., Pt 9 Sn 1 , Pt 8 Sn 2 , and Pt 7 Sn 3 , has been synthesized using a facile, room-temperature, wet-solution-based method. The crystallinity and chemical composition of these as-prepared samples were initially characterized using XRD, XPS, and EDX. Results revealed that this synthetic protocol could successfully generate PtSn alloys with purposely tunable chemical compositions. TEM and HRTEM verified the structural integrity of our ultrathin 1D NW morphology for our Pt 9 Sn 1 , Pt 8 Sn 2 , and Pt 7 Sn 3 samples. The effects of varying Sn content within these alloy samples toward the electro-oxidation reaction of methanol and ethanol were probed using cyclic voltammetry (CV) in acidic media. Finally, within this series, we find that the optimized chemical composition for both the MOR and the EOR is Pt 7 Sn 3 .

36 MATERIALS SCIENCE↗

Platinum Supported on NbRuyOz as Electrocatalyst for Ethanol Oxidation in Acid and Alkaline Fuel Cells

Platinum supported on a mixed metal oxide, NbRu{sub y}O{sub z} (8Nb:1Ru), was evaluated as an electrocatalyst for the ethanol oxidation reaction (EOR) in 0.1 M HClO{sub 4} and 1 M KOH. The support was synthesized from a liquid precursor solution of metal chlorides that was aerosolized and thermally decomposed into a powder via the spray pyrolysis (SP) process. Two samples were of primary interest: 30%Pt deposited onto the support by dry impregnation and 60%Pt as part of the precursor solution that underwent in situ SP Pt dispersion. TEM, SEM, and XRD were used to confirm morphology and deposition of Pt. XPS and XAS studies confirmed elemental distribution and oxidation state of Pt catalyst. In situ IRRAS studies in 0.1 M HClO{sub 4} show that these electrocatalysts are capable of facilitating the complete oxidation pathway of EOR, involving scission of the C-C bond and CO oxidation.

30 DIRECT ENERGY CONVERSION↗

Benefits of Damage Engineering for PMOS Junction Stability

As CMOS devices continue to shrink, the formation of ultra shallow junction (USJ) in the source/drain extension remains to be a key challenge requiring high dopant activation, shallow dopant profile and abrupt junctions. The next generations of sub nano-CMOS devices impose a new set of challenges such as elimination of residual defects resulting in higher leakage, difficulty to control lateral diffusion, junction stability post anneal and junction formation in new materials. To address these challenges for advanced technological nodes beyond 32 nm, it is imperative to explore novel species and techniques. Molecular species such as Carborane (C{sub 2}B{sub 10}H{sub 12}), a novel doping species and a promising alternative to monomer Boron is of considerable interest due to the performance boost for 22 nm low power and high performance devices. Also, to reduce residual defects, damage engineering methodologies have generated a lot of attention as it has demonstrated significant benefits in device performance. Varian proprietary techniques to perform implants at cold temperatures (PTC II) have demonstrated lower junction leakage, enhanced activation, reduced dopant diffusion and less dopant deactivation due to the reduction of self-interstitial atoms present at the end-of-range (EOR) with low implant temperatures. In this paper, for the first time, there is a comprehensive study of the effect of implant temperature on defect engineering affecting deactivation/reactivation, and it is well established in this paper that colder the implant temperature the better it is for damage engineering with reduced EOR defects and better amorphization. The effect has been studied over a wide range of implant temperature. To understand any difference in deactivation between molecular and monomer Boron and to provide direct comparison equivalent Boron implants, co-implanted with Carbon were also studied. Implants with wide range of temperatures are implemented using PTC II. This paper will also show how damage reduction correlates with optimum junction formation and stability.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

BF{sub 3} PIII modeling: Implantation, amorphisation and diffusion

In the race for highly doped ultra-shallow junctions (USJs) in complementary metal oxide semi-conductor (CMOS) technologies, plasma immersion ion implantation (PIII) is a promising alternative to traditional beamline implantation. Currently, no commercial technology computer aided design (TCAD) process simulator allows modeling the complete USJ fabrication process by PIII, including as-implanted dopant profiles, damage formation, dopant diffusion and activation. In this work, a full simulation of a p-type BF{sub 3} PIII USJ has been carried out. In order to investigate the various physical phenomena mentioned above, process conditions included a high energy/high dose case (10 kV, 5 Multiplication-Sign 10{sup 15} cm{sup -2}), specifically designed to increase damage formation, as well as more technology relevant implant conditions (0.5 kV) for comparison. All implanted samples were annealed at different temperatures and times. As implanted profiles for both boron and fluorine in BF{sub 3} implants were modeled and compared to Secondary Ion Mass Spectrometry (SIMS) measurements. Amorphous/crystalline (a/c) interface depths were measured by transmission electron microscopy (TEM) and successfully simulated. Diffused profiles simulations agreed with SIMS data at low thermal budgets. A boron peak behind the a/c interface was observed in all annealed SIMS profiles for the 10 kV case, indicating boron trapping from EOR defects in this region even after high thermal budgets. TEM measurements on the annealed samples showed an end of range (EOR) defects survival behind the a/c interface, including large dislocation loops (DLs) lying on (001) plane parallel to the surface. In the last part of this work, activation simulations were compared to Hall measurements and confirmed the need to develop a (001) large BICs model.

36 MATERIALS SCIENCE↗

Studies on dispersive stabilization of porous media flows

Motivated by a need to improve the performance of chemical enhanced oil recovery (EOR) processes, we investigate dispersive effects on the linear stability of three-layer porous media flow models of EOR for two different types of interfaces: permeable and impermeable interfaces. Results presented are relevant for the design of smarter interfaces in the available parameter space of capillary number, Peclet number, longitudinal and transverse dispersion, and the viscous profile of the middle layer. The stabilization capacity of each of these two interfaces is explored numerically and conditions for complete dispersive stabilization are identified for each of these two types of interfaces. Key results obtained are (i) three-layer porous media flows with permeable interfaces can be almost completely stabilized by diffusion if the optimal viscous profile is chosen, (ii) flows with impermeable interfaces can also be almost completely stabilized for short time, but become more unstable at later times because diffusion flattens out the basic viscous profile, (iii) diffusion stabilizes short waves more than long waves which leads to a “turning point” Peclet number at which short and long waves have the same growth rate, and (iv) mechanical dispersion further stabilizes flows with permeable interfaces but in some cases has a destabilizing effect for flows with impermeable interfaces, which is a surprising result. These results are then used to give a comparison of the two types of interfaces. It is found that for most values of the flow parameters, permeable interfaces suppress flow instability more than impermeable interfaces.

42 ENGINEERING↗

INTENSITY MAPPING WITH CARBON MONOXIDE EMISSION LINES AND THE REDSHIFTED 21 cm LINE

We quantify the prospects for using emission lines from rotational transitions of the CO molecule to perform an 'intensity mapping' observation at high redshift during the Epoch of Reionization (EoR). The aim of CO intensity mapping is to observe the combined CO emission from many unresolved galaxies, to measure the spatial fluctuations in this emission, and to use this as a tracer of large-scale structure at very early times in the history of our universe. This measurement would help determine the properties of molecular clouds-the sites of star formation-in the very galaxies that reionize the universe. We further consider the possibility of cross-correlating CO intensity maps with future observations of the redshifted 21 cm line. The cross spectrum is less sensitive to foreground contamination than the auto power spectra, and can therefore help confirm the high-redshift origin of each signal. Furthermore, the cross spectrum measurement would help extract key information about the EoR, especially regarding the size distribution of ionized regions. We discuss uncertainties in predicting the CO signal at high redshift, and discuss strategies for improving these predictions. Under favorable assumptions and feasible specifications for a CO survey mapping the CO(2-1) and CO(1-0) lines, the power spectrum of CO emission fluctuations and its cross spectrum with future 21 cm measurements from the Murchison Widefield Array are detectable at high significance.

79 ASTRONOMY AND ASTROPHYSICS↗

FOUR FUNDAMENTAL FOREGROUND POWER SPECTRUM SHAPES FOR 21 cm COSMOLOGY OBSERVATIONS

Contamination from instrumental effects interacting with bright astrophysical sources is the primary impediment to measuring Epoch of Reionization (EoR) and Baryon Acoustic Oscillations (BAO) 21 cm power spectra-an effect called mode mixing. In this paper, we identify four fundamental power spectrum shapes produced by mode mixing that will affect all upcoming observations. We are able, for the first time, to explain the wedge-like structure seen in advanced simulations and to forecast the shape of an 'EoR window' that is mostly free of contamination. Understanding the origins of these contaminations also enables us to identify calibration and foreground subtraction errors below the imaging limit, providing a powerful new tool for precision observations.

79 ASTRONOMY AND ASTROPHYSICS↗