Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Drag coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Aero-assisted orbital plane change using an elliptic drag polar

A three-impulse, aero-assisted maneuver is used to change the plane of a circular orbit. The guidance law used during the atmospheric phase is based on the repetitive use of an approximate optimal control law. The approximations include Loh's term being constant, an exponential atmosphere, and a constant-coefficient drag polar. Whereas the true optimal trajectory is flown at maximum lift-to-drag ratio, simulation results for a parabolic drag polar show the angle of attack becoming large near the end of the trajectory. Here, the approximate optimal control rule is developed for an elliptic polar which has maximum lift coefficient and higher values of the drag coefficient at high values of the lift coefficient than the parabolic polar. Simulation results show that the angle of attack still increases to high values near the end of the trajectory and that, overall, the parabolic drag polar produces better results. Finally, it is shown that Loh's term is not constant over the ascent portion of the atmospheric turn and is the probable cause of high angles of attack. However, the guidance laws developed by assuming Loh's term to be constant work well.

Hull, D. G.↗
NASA NTRS1947

Effects of Compressibility on the Flow Past Thick Airfoil Sections

Six, 3-inch-chord symmetrical airfoil sections having systematic variations in thickness and thickness location were tested at Mach numbers near flight values for propeller-shank sections. The tests, the results of which are presented in the form of schlieren photographs of the flow past each model and pressure-distribution charts for two of the model, were performed to illustrate the effects of compressibility on the flow past thick symmetrical airfoil sections. Representative flow photographs indicated that at Mach numbers approximately 0.05 above the critical Mach number a speed region was reached in which the flow oscillated rapidly and the separation point and the location of the shock wave were unstable. Fixing the transition on both surfaces of the airfoil was effective in reducing these rapid oscillations. The pressure distributions showed that the section normal-force coefficients for thick airfoils were very erratic at subcritical speeds; at supercritical speeds the section normal-force coefficients for the thick airfoils became more regular. Drag coefficients showed that considerable drag decreases can be expected by decreasing the model thickness ratio.

Daley, Bernard N.↗
NASA NTRS1944

Wind-Tunnel Investigation of an NACA 23021 Airfoil with a 0.32-Airfoil-Chord Double Slotted Flap

An investigation was made in the LMAL 7- by 10-foot wind tunnel of a NACA 23021 airfoil with a double slotted flap having a chord 32 percent of the airfoil chord (0.32c) to determine the aerodynamic section characteristics with the flaps deflected at various positions. The effects of moving the fore flap and rear flap as a unit and of deflecting or removing the lower lip of the slot were also determined. Three positions were selected for the fore flap and at each position the maximum lift of the airfoil was obtained with the rear flap at the maximum deflection used at that fore-flap position. The section lift of the airfoil increased as the fore flap was extended and maximum lift was obtained with the fore flap deflected 30 deg in the most extended position. This arrangement provided a maximum section lift coefficient of 3.31, which was higher than the value obtained with either a 0.2566c or a 0.40c single-slotted-flap arrangement and 0.25 less than the value obtained with a 0.4c double-slotted-flap arrangement on the same airfoil. The values of the profile-drag coefficient obtained with the 0.32c double slotted flap were larger than those for the 0.2566c or 0.40c single slotted flaps for section lift coefficients between 1.0 and approximately 2.7. At all values of the section lift coefficient above 1.0, the 0.40c double slotted flap had a lower profile drag than the 0.32c double slotted flap. At various values of the maximum section lift coefficient produced by various flap defections, the 0.32c double slotted flap gave negative section pitching-moment coefficients that were higher than those of other slotted flaps on the same airfoil. The 0.32c double slotted flap gave approximately the same maximum section lift coefficient as, but higher profile-drag coefficients over the entire lift range than, a similar arrangement of a 0.30c double slotted flap on an NACA 23012 airfoil.

SLOTTED↗
NASA NTRS1975

Propulsive effects due to flight through turbulence

A simple and straightforward analysis is presented for evaluating the approximate magnitude of the propulsive effect for various types of airplane (soaring glider, light airplane, fighter, and transport). The airplane, subject to vertical gust disturbances, is assumed to be constrained to fly at constant airspeed and constant pitch angle. Changes in the magnitude and direction of the lift vector are taken into account. It is shown that the thrust effects due to turbulence vary as the square of the turbulence intensity and are quite small for moderate turbulence. Only for rather severe turbulence are the effects large enough to be given any consideration. The thrust coefficient is 10-20% of the drag coefficient of a soaring glider.

Phillips, W. H.↗
NASA NTRS1989

Effect of milling machine roughness and wing dihedral on the supersonic aerodynamic characteristics of a highly swept wing

An experimental investigation was conducted to assess the effect of surface finish on the longitudinal and lateral aerodynamic characteristics of a highly-swept wing at supersonic speeds. A study of the effects of wing dihedral was also made. Included in the tests were four wing models: three models having 22.5 degrees of outboard dihedral, identical except for surface finish, and a zero-dihedral, smooth model of the same planform for reference. Of the three dihedral models, two were taken directly from the milling machine without smoothing: one having a maximum scallop height of 0.002 inches and the other a maximum scallop height of 0.005 inches. The third dihedral model was handfinished to a smooth surface. Tests were conducted in Test Section 1 of the Unitary Plan Wind Tunnel at NASA-Langley over a range of Mach numbers from 1.8 to 2.8, a range of angle of attack from -5 to 8 degrees, and at a Reynolds numbers per foot of 2 x 10(6). Selected data were also taken at a Reynolds number per foot of 6 x 10(6). Drag coefficient increases, with corresponding lift-drag ratio decreases were the primary aerodynamic effects attributed to increased surface roughness due to milling machine grooves. These drag and lift-drag ratio increments due to roughness increased as Reynolds number increased.

Darden, Christine M.↗
NASA NTRS1991

A two-dimensional Euler solution for an unbladed jet engine configuration

A two dimensional nonaxisymmetric Euler solution in a geometric representation of a jet engine configuration without blades is presented. The domain, including internal and external flow, is covered with a multiblock grid. To construct the grid, a domain decomposition technique is used to subdivide the domain and smooth grids are dimensioned and placed in each block. The grid contains 44 blocks which cover the external field, the inlet, bypass duct, core duct and nozzle of the nonaxisymmetric engine configuration. The geometry is symmetric about the meanline of the hub, but the grid is not since there is no symmetry condition applied to the grid between the two halves. With a symmetric grid at zero angle of attack, the measures of the solution would cancel exactly. With an asymmetric grid, the solution will not necessarily be symmetric and the lift coefficient will not necessarily be zero. Thus, grid asymmetry can be exploited to verify the resolution of the solution. The solution may be verified on the basis of five theoretical quantities: conservation of mass and energy, deviation of the lift coefficient from zero, deviation of the drag coefficient from zero, deviations from constant entropy, and deviations in the pressure distributions over the symmetric surfaces of the components. This technique is suitable for obtaining numerical solutions in complex geometries and provides a foundation for complete engine throughflow calculations.

Stewart, Mark E. M.↗
NASA NTRS1931

Experiments with an Airfoil Model on which the Boundary Layers are Controlled Without the Use of Supplementary Equipment

This report describes test made in the Variable Density Wind Tunnel of the NACA to determine the possibility of controlling the boundary layer on the upper surface of an airfoil by use of the low pressure existing near the leading edge. The low pressure was used to induce flow through slots in the upper surface of the wing. The tests showed that the angle of attack for maximum lift was increased at the expense of a reduction in the maximum lift coefficient and an increase in the drag coefficient.

Abbott, I H↗
NASA NTRS1998

Aerothermodynamics of the Mars Global Surveyor Spacecraft

The aerothermodynamics characteristics of the Mars Global Surveyor spacecraft are investigated and reported. These results have been used by the Mars Global Surveyor mission planners to design the aerobraking phase of the mission. Analytical and Direct Simulation Monte Carlo computer codes were used with a detailed, three dimensional model of the spacecraft to evaluate spacecraft aerobraking characteristics for flight in free molecular and transitional flow regimes. The spacecraft is found to be aerodynamically stable in aerobraking and planned contingency configurations. Aerodynamic forces, moments, and heating are found to be highly dependent on atmospheric density. Accommodation coefficient. is seen to strongly influence drag coefficient. Transitional flow effects are found to reduce overall solar panel heating. Attitude control thruster plumes are shown to interact with the freestream, diminishing the effectiveness of the attitude control system and even leading to thrust reversal. These plume-freestream interaction effects are found to be highly dependent on freestream density.

Shane, Russell W.↗
NASA NTRS1960

Effect of Afterbody Terminal Fairings on the Performance of a Pylon-Mounted Turbojet-Nacelle Model

An investigation of the effect of afterbody terminal fairings on the performance of a pylon-mounted turbojet-nacelle model has been conducted in the Langley 16-foot transonic tunnel. A basic afterbody having a boattail angle of 16 deg was investigated with and without terminal fairings. The equivalent boattail angle, based on the cross-sectional area of the afterbody and terminal fairings, was 8 deg. Therefore, a simple body of revolution with a boattail angle of 8 deg was included for comparison. The tests were made at an angle of attack of 0 deg, Mach numbers of 0.80 to 1.05, jet total-pressure ratio of 1 to approximately 5, and an average Reynolds number per foot of 4.1 x 10(exp 6). A hydrogen peroxide jet simulator was used to supply the hot-jet exhaust. The results indicate that addition of terminal fairings to a 16 deg boattail afterbody increased the thrust-minus-drag coefficients and provided the lowest effective drag of the three configurations tested.

Willis, Conrad M.↗
NASA NTRS1994

Comment on 'Guidance for an Aerocapture Maneuver

It is stated that the aerodynamic forces on the vehicle being aerocaptured are controlled by "altering the angle of attack" and thereby controlling the lift coefficient. Furthermore, the resulting variation of drag coefficient with angle of attack was ignored. The purpose of this Comment is to point out that an aerodynamic control method that is much more effective than the pitch modulation has been studied and utilized during entries for many years. During aerocapture, it is desirable to have a large range of lift coefficients available, while keeping the vehicle's ballistic coefficients constant. This is accomplished by modulating the vehicle's bank angle, i.e., by rolling the vehicle about its velocity vector. By this method, the angle of attack can be held constant (at the trim angle, if desired), and the C(sub D) and the ballistic coefficient remain constant. Furthermore, the vertical component of the normal force vector (essentially the lift) can be varied over its entire range, from maximum positive to maximum negative values. Reaction controls, rather than aerodynamic ones, are usually utilized to change the bank angle of the vehicle, thus requiring the use of fuel. However, the fuel expenditure that is required to change the bank angle is far less than the amount that would have to be used to continuously hold the vehicle at pitch angles that differ significantly from its trim angle of attack. Also, it has been shown that bank angle modulation to vary the lift can enlarge the entry corridor by increasing the entry angle for the undershoot boundary, where both the heating rate and deceleration reach a maximum. Finally, the crew's deceleration tolerance can be increased somewhat when the bank angle is varied, as opposed to the pitch angle. For bank modulation, the deceleration force vector can be kept at a constant angle with respect to the occupants whose tolerance to g loads is highest when the force is applied in a direction normal to the upper torso. The advantages of bank angle variation to modulate the lift vector were recognized long ago, and this method of control was used successfully on the Apollo command module during lunar return' and, more recently, for the Space Shuttle Orbiter.

Tauber, Michael E.↗
NASA NTRSDate not supplied

Machine Learning Approach for Aircraft Performance Model Parameter Estimation for Trajectory Prediction Applications

Inaccurate prediction of aircraft trajectory by ground-based decision support tools (DST) is a major concern in air traffic management (ATM). Aircraft trajectory prediction tools rely on a simplified point-mass aircraft performance model (APM) to make their predictions. Even though the performance coefficients and weight of an aircraft are a vital part of the APM’s predictions and accuracy, these coefficients are proprietary in nature and therefore, unavailable to DSTs. Current ATM research focuses on improving the estimate of some APM parameters by freezing all other coefficients. This simplified approach introduces unwanted sources of bias and negatively impacts the accuracy of the performance model. In this paper, we apply machine learning (ML) techniques for the simultaneous prediction of three key APM parameters (two drag coefficients and the initial aircraft weight). To accomplish this, we employ an ordinary differential equation (ODE) fitting approach to generate optimized APM parameter labels customized to each individual flight record. Subsequently, we train ML models to capture the relationship between the historical data and the optimized APM parameters. Two different ML model solutions are applied and APM coefficients are predicted for unseen flights. The results indicate that the ML models are able to capture the relationship between APM parameters and flight-related features with good accuracy.

trajectory prediction, machine learning, aircraft ↗
NASA NTRS1957

Comparison of Experimental and Theoretical Zero-Lift Wave-Drag Results for Various Wing-Body-Tail Combinations at Mach Numbers up to 1.9

Comparisons are made of experimental and theoretical zero-lift wave drag for several nose shapes, wing-body combinations, and models of current airplanes at Mach numbers up to 1.0. The experimental data were obtained from tests in the Ames 6- by6-foot supersonic wind tunnel and at the NACA Wallops Island facility. The theoretical drag was found by use of linear theory utilizing model area distributions. The agreement between theoretical and experimental zero-lift wave-drag coefficients was generally very good, especially for a fuselage or for fuselage-wing combinations that were vertically symmetrical. For other models that had rapid changes in body shape and/or were not vertically symmetrical, the agreement of theory with experiment ranged from fair to poor, depending on the severity of the change in shape.

DRAG COEFFICIENT↗
NASA NTRS1992

Computation of three-dimensional effects on two dimensional wings

A 2-D numerical investigation was performed to determine the effect of a Gurney flap on a NACA 4412 airfoil. A Gurney flap is a flat plate on the order of 1 to 3 percent of the airfoil chord length, oriented perpendicular to the airfoil chord line and located at the trailing edge of the airfoil. An incompressible Navier Stokes code, INS2D, was used to calculate the flow field about the airfoil. The fully turbulent results were obtained using the Baldwin-Barth one-equation turbulence model. Gurney flap sizes of 0.5, 1, 1.25, 1.5, 2, and 3 percent of the airfoil chord were studied. Computational results were compared with experimental results where possible. The numerical solutions show that the Gurney flap increases airfoil lift coefficient with only a slight increase in drag coefficient. Use of a 1.5 percent chord Gurney flap increases the maximum lift coefficient by approximately 0.3 and decreases the angle of attack for a given lift coefficient by more than 3 degrees. The numerical solutions exhibit detailed flow structures at the trailing edge and provide a possible explanation for the increased aerodynamic performance.

Cummings, Russell M.↗