Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Toward Low-Cost, High-Energy Density, and High-Power Density Lithium-Ion Batteries

Reducing cost and increasing energy density are two barriers for widespread application of lithium-ion batteries in electric vehicles. Although the cost of electric vehicle batteries has been reduced by ~70% from 2008 to 2015, the current battery pack cost (268/kWh in 2015) is still >2 times what the USABC targets (125/kWh). Even though many advancements in cell chemistry have been realized since the lithium-ion battery was first commercialized in 1991, few major breakthroughs have occurred in the past decade. Therefore, future cost reduction will rely on cell manufacturing and broader market acceptance. Here, this article discusses three major aspects for cost reduction: (1) quality control to minimize scrap rate in cell manufacturing; (2) novel electrode processing and engineering to reduce processing cost and increase energy density and throughputs; and (3) material development and optimization for lithium-ion batteries with high-energy density. Insights on increasing energy and power densities of lithium-ion batteries are also addressed.

25 ENERGY STORAGE↗

Two-layer cathode architecture for high-energy density and high-power density solid state batteries

Solid state batteries with high-energy density and high-power density require the development of thick and energy dense cathodes. Structured cathode electrodes with a double-layer configuration were enabled using a freeze tape casting technique. A bottom dense layer was utilized to enhance the energy density whereas a top porous layer with vertically aligned walls was utilized to enhance the power density. The porous structure of the power layer was achieved by ice templating this layer on top of the densified energy layer of the cathode. This configuration was found to better utilize the active material of the cathodes and was optimized using numerical simulation and computer modeling. Cells with Li metal anode and LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) at approximately 5 and 20 mg/cm 2 were cycled at 70 °C at different C-rates. Poly(ethylene oxide) (PEO) with lithium bis-trifluoromethanesulfonimide (LiTFSI) was used for the catholyte and the solid-state electrolyte. The structured cathodes exhibited more than double capacity values as well as better Coulombic efficiency compared to non-structured (single-layer) thick cathodes. In conclusion, synchrotron X-ray tomography and scanning electron microscopy were used to characterize the microstructure of the cathodes.

25 ENERGY STORAGE↗

Simulations of a high-density, highly-radiating lithium divertor

Results are presented for one- and two-dimensional (2D) edge plasma transport simulations for strong injection of lithium (Li) in the divertor region of a tokamak. The model includes the scrape-off layer and divertor regions, and, for 2D, a small region inside the magnetic separtrix. Equations are solved for the density and momentum of a deuterium/tritium (DT) species and all three charge states of Li, in addition to separate ion and electron energy equations via the UEDGE code. Equations are also included for the DT and Li gas species. Lithium gas is injected from the side walls or divertor plate, implying that these surfaces are evaporating liquid Li. For a range of Li gas input, steady-state, detached-plasma solutions are shown where greater than 90% of the exhaust power is radiated by Li, resulting in peak surface heat fluxes ~2 MW/m 2 on the divertor plate, outer wall, and private-flux wall. While Li ions dominate in the divertor leg, their density is in the range of 10% of the DT density at the midplane. The collisional parallel thermal force plays a key role in determining the midplane ion Li density, and sensitivity of results to different model assumptions are discussed. Here the key issue is possible dilution of the core DT fuel. A brief comparison of the Li neutral solution is made with that from the Direct Simulation Monte-Carlo (DSMC) SPARTA code.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Characterizing Density and Spatial Distribution of Trap States in Ta 3 N 5 Thin Films for Rational Defect Passivation

Tantalum nitride (Ta 3 N 5 ) has gained significant attention as a potential photoanode material, yet it has been challenged by material quality issues. Defect-induced trap states are detrimental to the performance of any semiconductor material. Beyond influencing the performance of Ta 3 N 5 films, defects can also accelerate the degradation in water during desired electrochemical applications. Defect passivation has provided an enormous boost to the development of many semiconductor materials but is currently in its infancy for Ta 3 N 5 . This is in part due to a lack of experimental understanding regarding the spatial and energetic distribution of trap states throughout Ta 3 N 5 thin films. Here, we employ drive-level capacitance profiling (DLCP) to experimentally resolve the spatial and energetic distribution of trap states throughout Ta 3 N 5 thin films. The density of deeper energetic traps is found to reach ∼2.5 to 6 × 10 22 cm –3 at the interfaces of neat Ta 3 N 5 thin films, over an order of magnitude greater than the bulk. In addition to the spatial profile of deep trap states, we report neat Ta 3 N 5 thin films to be highly n-type in nature, owning a free carrier density of ∼9.74 × 10 17 cm –3 . This information, coupled with the present understanding of native oxide layers on Ta 3 N 5 , has facilitated the rational design of a targeted passivation strategy that simultaneously provides a means for catalyst immobilization. Loading catalyst via silatrane moieties suppresses the density of defects at the surface of Ta 3 N 5 thin films by two orders of magnitude, while also reducing the free carrier density of films by over one order of magnitude, effectively dedoping the films to ∼2.40 × 10 16 cm –3 . The surface passivation of Ta 3 N 5 films translates to suppressed defect-induced trapping and recombination of photoexcited carriers, as determined through absorption, photoluminescence, and transient photovoltage. Here, this illustrates how developing a deeper understanding of the distribution and influence of defects in Ta 3 N 5 thin films has the potential to guide future works and ultimately accelerate the integration and development of high-performance Ta 3 N 5 thin film devices.

defect passivation↗

Uncertainties in turbulent statistics and fluxes of CO2 associated with density effect corrections

Density effect corrections (DEC) are applied to adjust raw CO2 fluxes measured by eddy covariance (EC) systems with open-path gas analyzers. DEC is also required for adjusting the measured CO2 concentration fluctuations to obtain the adjusted CO2 for analyzing turbulent statistics or quantifying fluxes. However, our data show that the power spectra of the DEC-adjusted CO2 are distorted in the high frequency range, as compared with the corresponding spectra of temperature and water vapor density. This contradicts the similarity behavior of scalars, as suggested by Monin-Obukhov similarity theory. It is demonstrated that such a distortion is caused by the DEC-induced spikes in the DEC-adjusted CO2, altering turbulent statistics of CO2 and scalar similarity between CO2 and other scalars. Our results suggest that CO2 fluxes are overestimated by applying DEC especially under high Bowen ratio conditions, potentially leading to substantial uncertainties in long-term ecosystem carbon exchange in dry regions.

Gao, Zhongming↗

Can Kohn–Sham density functional theory predict accurate charge distributions for both single-reference and multi-reference molecules?

Dipole moments are the first moment of electron density and are fundamental quantities that are often available from experiments. An exchange–correlation functional that leads to an accurate representation of the charge distribution of a molecule should accurately predict the dipole moments of the molecule. It is well known that Kohn–Sham density functional theory (DFT) is more accurate for the energetics of single-reference systems than for the energetics of multi-reference ones, but there has been less study of charge distributions. Here, in this work, we benchmark 48 density functionals chosen with various combinations of ingredients, against accurate experimental data for dipole moments of 78 molecules, in particular 55 single-reference molecules and 23 multi-reference ones. We chose both organic and inorganic molecules, and within the category of inorganic molecules there are both main-group and transition-metal-containing molecules, with some of them being multi-reference. As one would expect, the multi-reference molecules are not as well described by single-reference DFT, and the functionals tested in this work do show larger mean unsigned errors (MUEs) for the 23 multi-reference molecules than the single-reference ones. Five of the 78 molecules have relatively large experimental error bars and were therefore not included in calculating the overall MUEs. For the 73 molecules not excluded, we find that three of the hybrid functionals, B97-1, PBE0, and TPSSh (each with less than or equal to 25% Hartree–Fock (HF) exchange), the range-separated hybrid functional, HSE06 (with HF exchange decreasing from 25% to 0 as interelectronic distance increases), and the hybrid functional, PW6B95 (with 28% HF exchange) are the best performing functionals with each yielding an MUE of 0.18 D. Perhaps the most significant finding of this study is that there exists great similarity among the success rate of various functionals in predicting dipole moments. In particular, of 39 functionals designed as general-purpose functionals and that do not have a global value of 100% HF exchange, the average MUE is 0.23 D, with a standard deviation of only 0.04 D. Among gradient approximations, which are especially interesting because of their speed and portability, the best overall performance is by PBE, HCTH/407, OLYP, OreLYP, and GAM, each with MUE of 0.22 D.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Coupled-cluster, Möller Plesset (MP2), Density Fitted Local MP2, and Density Functional Theory Examination of the Energetic and Structural Features of Hydrophobic Solvation: Water and Pentane

The interaction potentials between immiscible polar and non-polar solvents are a major driving force behind the formation of liquid:liquid interfaces. In this work, the interaction energy of water–pentane dimer has been determined using coupled-cluster theory with single double (triple) excitations [CCSD(T)], 2nd order Möller Plesset perturbation theory (MP2), density fitted local MP2 (DF-LMP2), as well as density functional theory using a wide variety of density functionals and several different basis sets. The M05-2X exchange correlation functionals exhibit excellent agreement with CCSD(T) and DF-LMP2 after taking into account basis set superposition error. The gas phase water–pentane interaction energy is found to be quite sensitive to the specific pentane isomer (2,2- dimethylpropane vs. n-pentane) and relative orientation of the monomeric constituents. Subsequent solution phase cluster calculations of 2,2-dimethylpropane and n-pentane solvated by water indicate a positive free energy of solvation that is in good agreement with available experimental data. Structural parameters are quite sensitive to the density functional employed and reflect differences in the two-body interaction energy calculated by each method. In contrast, cluster calculations of pentane solvation of H2O solute are found to be inadequate for describing the organic solvent, likely due to limitations associated with the functionals employed (B3LYP, BHandH, and M05-2X).

Environmental Molecular Sciences Laboratory↗

Cryogenic tritium-hydrogen-deuterium and deuterium-tritium layer implosions with high density carbon ablators in near-vacuum hohlraums

High Density Carbon (or diamond) is a promising ablator material for use in near-vacuum hohlraums, as its high density allows for ignition designs with laser pulse durations of <10 ns. A series of Inertial Confinement Fusion (ICF) experiments in 2013 on the National Ignition Facility [Moses et al., Phys. Plasmas 16, 041006 (2009)] culminated in a deuterium-tritium (DT) layered implosion driven by a 6.8 ns, 2-shock laser pulse. This paper describes these experiments and comparisons with ICF design code simulations. Backlit radiography of a tritium-hydrogen-deuterium (THD) layered capsule demonstrated an ablator implosion velocity of 385 km/s with a slightly oblate hot spot shape. Other diagnostics suggested an asymmetric compressed fuel layer. A streak camera-based hot spot self-emission diagnostic (SPIDER) showed a double-peaked history of the capsule self-emission. Simulations suggest that this is a signature of low quality hot spot formation. Changes to the laser pulse and pointing for a subsequent DT implosion resulted in a higher temperature, prolate hot spot and a thermonuclear yield of 1.8 × 10{sup 15} neutrons, 40% of the 1D simulated yield.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

An x-ray backlit Talbot-Lau deflectometer for high-energy-density electron density diagnostics

X-ray phase-contrast techniques can measure electron density gradients in high-energy-density plasmas through refraction induced phase shifts. An 8 keV Talbot-Lau interferometer consisting of free standing ultrathin gratings was deployed at an ultra-short, high-intensity laser system using K-shell emission from a 1-30 J, 8 ps laser pulse focused on thin Cu foil targets. Grating survival was demonstrated for 30 J, 8 ps laser pulses. The first x-ray deflectometry images obtained under laser backlighting showed up to 25% image contrast and thus enabled detection of electron areal density gradients with a maximum value of 8.1 ± 0.5 × 10 23 cm ₋3 in a low-Z millimeter sized sample. An electron density profile was obtained from refraction measurements with an error of <8%. We found the 50 ± 15 μm spatial resolution achieved across the full field of view was limited by the x-ray source-size, similar to conventional radiography.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Effect of strain rate and dislocation density on the twinning behavior in tantalum

The conditions which affect twinning in tantalum have been investigated across a range of strain rates and initial dislocation densities. Tantalum samples were subjected to a range of strain rates, from 10{sup −4}/s to 10{sup 3}/s under uniaxial stress conditions, and under laser-induced shock-loading conditions. In this study, twinning was observed at 77 K at strain rates from 1/s to 10{sup 3}/s, and during laser-induced shock experiments. The effect of the initial dislocation density, which was imparted by deforming the material to different amounts of pre-strain, was also studied, and it was shown that twinning is suppressed after a given amount of pre-strain, even as the global stress continues to increase. These results indicate that the conditions for twinning cannot be represented solely by a critical global stress value, but are also dependent on the evolution of the dislocation density. In addition, the analysis shows that if twinning is initiated, the nucleated twins may continue to grow as a function of strain, even as the dislocation density continues to increase.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Spatially resolved density and ionization measurements of shocked foams using x-ray fluorescence

We present experiments at the Trident laser facility demonstrating the use of x-ray fluorescence (XRF) to simultaneously measure density, ionization state populations, and electron temperature in shocked foams. An imaging x-ray spectrometer obtained spatially resolved measurements of Ti K-α emission. Density profiles were measured from K-α intensity. Ti ionization state distributions and electron temperatures were inferred by fitting K-α spectra to spectra from CRETIN simulations. This work shows that XRF provides a powerful tool to complement other diagnostics to make equation of state measurements of shocked materials containing a suitable tracer element.

36 MATERIALS SCIENCE↗

Perspective: Kohn-Sham density functional theory descending a staircase

This article presents a perspective on Kohn-Sham density functional theory (KS-DFT) for electronic structure calculations in chemical physics. This theory is in widespread use for applications to both molecules and solids. We pay special attention to several aspects where there are both concerns and progress toward solutions. These include: The treatment of open-shell and inherently multiconfigurational systems (the latter are often called multireference systems and are variously classified as having strong correlation, near-degeneracy correlation, or high static correlation; KS-DFT must treat these systems with broken-symmetry determinants). The treatment of noncovalent interactions. The choice between developing new functionals by parametrization, by theoretical constraints, or by a combination. The ingredients of the exchange-correlation functionals used by KS-DFT, including spin densities, the magnitudes of their gradients, spin-specific kinetic energy densities, nonlocal exchange (Hartree-Fock exchange), nonlocal correlation, and subshell-dependent corrections (DFT+U). The quest for a universal functional, where we summarize some of the success of the latest Minnesota functionals, namely MN15-L and MN15, which were obtained by optimization against diverse databases. Time-dependent density functional theory, which is an extension of DFT to treat time-dependent problems and excited states. Furthermore, the review is a snapshot of a rapidly moving field, and—like Marcel Duchamp—we hope to convey progress in a stimulating way.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Rethinking the magnetic properties of lepidocrocite: A density functional theory and cluster expansion study

The iron oxyhydroxide lepidocrocite (g-FeOOH) is an abundant mineral critical to a number of chemical and technological applications. Of particular interest is the ground state and nite temperature magnetic order, and the subsequent impact this has upon crystal properties. The magnetic properties, investigated in this work are governed primarily through superexchange interactions, and have been calculated using density functional theory and cluster expansion methods. Quantication of these exchange terms has facilitated the determination of the ground state magneto-crystalline structure and subsequent calculation of its lattice constants, elastic moduli, cohesive enthalpy, and electronic density of states. Further, using a collinear magnetic conguration model, the magnetic heat capacity versus temperature has been studied and the Neel temperature obtained.

Pope, Daniel J.↗

Gauge-invariant perturbation expansion in powers of electric charge for the density-of-states of a network model for charged-particle motion in a uniform background magnetic flux density

An explicitly gauge-invariant expansion in powers of e/$\hbar$ times the magnetic flux density is formally obtained for the density of states [as characterized by the trace of the resolvent $\hat{G}$ = (ω-$\hat{ℎ}$)-1] of a charged particle moving on a Hermitian quantum network that is embedded in a Euclidean background that supports a uniform magnetic flux density. The explicit expressions, given here up to third order in the flux density, are also valid for the “local trace” (the trace of $\hat{P}_i\hat{G}$ , where $\hat{P}_i$ is the projector on a network node) and do not appear to have been previously given.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Reflection-asymmetric nuclear deformations within the Density Functional Theory

Within the nuclear density functional theory (DFT) we study the effect of reflection-asymmetric shapes on ground-state binding energies and binding energy differences. To this end, we developed the new DFT solver AXIALHFB that uses an approximate second-order gradient to solve the Hartree-Fock-Bogoliubov equations of superconducting DFT with the quasi-local Skyrme energy density functionals. Illustrative calculations are carried out for even-even isotopes of radium and thorium.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Imaging of transition charge densities involving carbon core excitations by all X-ray sum-frequency generation

X-ray diffraction signals from the time-evolving molecular charge density induced by selective core excitation of chemically inequivalent carbon atoms are calculated. A narrowband X-ray pulse selectively excites the carbon K-edge of the –CH 3 or –CH 2 F groups in fluoroethane (CH 3 –CH 2 F). Each excitation creates a distinct core coherence which depends on the character of the electronic transition. Direct propagation of the reduced single-electron density matrix, using real-time time-dependent density functional theory, provides the time-evolving charge density following interactions with external fields. Here, the interplay between partially filled valence molecular orbitals upon core excitation induces characteristic femtosecond charge migration which depends on the core–valence coherence, and is monitored by the sum-frequency generation diffraction signal.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Unconventional electronic reconstruction in undoped ( Ba , Sr ) Fe 2 As 2 across the spin density wave transition

Through a systematic high-resolution angle-resolved photoemission study of the iron pnictide compounds ( Ba , Sr ) Fe 2 As 2 , we show that the electronic structures of these compounds are significantly reconstructed across the spin density wave transition, which cannot be described by a simple folding scenario of conventional density wave ordering. Furthermore, we find that LDA calculations with an incorporated suppressed magnetic moment of 0.5μ B can match well the details in the reconstructed electronic structure, suggesting that the nature of magnetism in the pnictides is more migratory than local, while the origin of suppressed magnetic moment remains an important issue for future investigations.

36 MATERIALS SCIENCE↗