Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Data Flow Reversal”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Microtopographic evolution of lava flows at Cima volcanic field, Mojave Desert, California

Microtopographic profiles were measured and power spectra calculated for dated lava flow surfaces at Cima volcanic field in the eastern Mojave Desert of California in order to quantify changes in centimeter- to meter-scale roughness as a function of age. For lava flows younger than about 0.8 m.y., roughness over all spatial scales decreases with age, with meter-scale roughness decreasing slightly more than centimeter scales. Flows older than about 0.8 m.y. show a reversal of this trend, becoming as rough as young flows at these scales. Modeling indicates that eolian deposition can explain most of the change observed in the offset, or roughness amplitude, of power spectra of flow surface profiles up to 0.8 m.y. Other processes, such as rubbing and stone pavement development, appear to have a minor effect in this age range. Changes in power spectra of surfaces older than about 0.8 m.y. are consistent with roughening due to fluvial dissection. These results agree qualitatively with a process-response model that attributes systematic changes in flow surface morphology to cyclic changes in the rates of eolian, soil formation, and fluvial processes. Identification of active surficial processes and estimation of the extent of their effects, or stage of surficial evolution, through measurement of surface roughness will help put the correlation of surficial units on a quantitative basis. This may form the basis for the use of radar remote sensing data to help in regional correlations of surficial units.

Farr, Tom G.↗
NASA NTRS2018

Hybrid Reduced Order Model for N2-N2 Interactions for Application to Dissociation and Energy Transfer Processes

Recent work in the aerothermodynamics community has focused on the development of reduced-order models for thermo-chemical non-equilibrium which avoid the restrictive assumptions of multi-temperature models and the prohibitive cost associated with State-to-State (StS) models. In the present work, this is accomplished by lumping energy states together and assuming groups of states are roughly in equilibrium. As a result, the non-equilibrium behavior of a gas can be captured at a reduced computational cost from a full StS simulation. In this work, we present a hybrid grouping model for studying energy transfer and dissociation in a mixture of nitrogen molecules due to N2-N2 reactions. This is accomplished by making use of a grouping strategy informed by data from the N2-N StS kinetic data. However, due to the massive computational cost associated with constructing StS data for the N2-N2 system, the kinetic data for the hybrid grouping model are calculated using the quasi-classical trajectory (QCT) method by sampling states for trajectory within the groups. This general framework is called the Maximum-Entropy Quasi-Classical Trajectory (ME-QCT) method. The primary challenge associated with this method is that rates for reverse grouped reactions cannot be obtained through detailed balance at a group level, due to the variation of group internal temperatures. To construct the full model for N2-N2 grouped kinetics using the ME-QCT method, detailed balance is invoked at the microscopic level, allowing for the calculation of the full kinetic data from QCT. Results will be presented using the full ME-QCT model for the N2-N2 system in an isothermal and isochoric reactor simulation. In addition, simple CFD test cases for a one-dimensional standing shock and for a quasi-one-dimensional nozzle will be used for demonstration of the ME-QCT method. This method allows for the calculation of non-equilibrium behavior for the N2-N2 system without the prohibitive cost of a full StS simulation. Moreover, it enables the construction of a unified model for the dissociating and recombining non-equilibrium flows.

nonequilibrium modeling↗
NASA NTRS1979

Reduction of rotor-turbulence interaction noise in static fan noise testing

Three effective inlet cleanup methods are described. A flared reverse cone inlet is used to eliminate wakes from the fan casings and/or probe supports. Boundary layer suction is employed ahead of the fan rotor and on the outer flare of the cone to reduce the boundary layer turbulence and remove any residual wakes. To reduce the midstream turbulent intensity and length scales, a turbulence control structure is used which is constructed with both a layer of honeycomb and a fine mesh screen. The effects of these cleanup methods are quantified by measuring the far-field noise in an anechoic chamber, using a high-speed 20-in.-diam fan of the current high passband type. The changes in the turbulent field impinging on this rotor are quantified by mapping the streamwise and transverse turbulent properties (spectra, intensity and length scale) with crossed hot film probes. It is convincingly shown that it is possible to clean up the inlet flow of a static fan noise test facility to a point where the static acoustic data simulate flight data.

Kantola, R. A.↗
NASA NTRS1998

Seasonal Cycles of Meridional Overturning and Heat Transport of the Indian Ocean

A general circulation model of the Indian Ocean is fitted to monthly averaged climatological temperatures, salinities, and surface fluxes using the adjoint method. Interannual variability is minimized by penalizing the temporal drift from one seasonal cycle to another during a two-year integration. The resultant meridional overturning and heat transport display large seasonal variations, with maximum amplitudes of 18 and 22 (x 10(exp 6) cubic m/s) for the overturning and 1.8 and 1.4 (x 10(exp 15) W) for heat transport near 10 S and 10 N, respectively. A dynamical decomposition of the overturning and heat transport shows that the time-varying Ekman How plus its barotropic compensation can explain a large part of the seasonal variations in overturning and heat transport. The maximum variations at 10 deg N and 10 deg S are associated with monsoon reversal over the northern Indian Ocean and changes of the easterlies over the southern Indian Ocean. An external mode with variable topography has a moderate contribution where the Somali Current and the corresponding gyre reverse direction seasonally. Contribution front vertical shear (thermal wind and ageostrophic shear) is dominant near the southern boundary and large near the Somali Current latitudes. The dominant balance in the zonally integrated heat budget is between heat storage change and heat transport convergence except south of 15 S. Optimization with seasonal forcings improves estimates of sea surface temperatures, but the annual average overturning and heat transport are very similar to previous results with annual mean forcings. The annual average heat transport consists of roughly equal contributions from time-mean and time-varying fields of meridional velocities and temperatures in the northern Indian Ocean. indicating a significant rectification to the heat transport due to the time-varying fields. The time-mean and time-varying contributions are primarily due to the overturning and horizontal gyre, respectively. Inclusion of TOPEX data enhances the seasonal cycles of the estimated overturning and heat transport in the central Indian Ocean significantly and improves the estimated equatorial zonal flows but leads 10 unrealistic estimates of the velocity structure near the Indonesian Throughflow region, most likely owing to the deficiencies in the lateral boundary conditions.

Lee, Tong↗
NASA NTRS1989

Seven hole probe measurement of leading edge vortex flows

This paper discusses the use of a seven-hole probe on measurements of leading edge vortices of highly sweep delta wing planforms. Intrusive probe data taken with the pressure probe were compared with nonintrusive measurements made with laser Doppler anemometry system. In addition to probe size, the natural position of breakdown and the sweep angle of the wing are also factors in determining sensitivity of the flow to probe interference. At low angles of attach vortex breakdown does not occur in the vicinity of the model and the seven hole probe was found to yield reasonably accurate measurements. When the angle of attack of the model was increased so that vortex breakdown was near the trailing edge, introducing the probe over the wing would cause the breakdown position to move ahead of the probe. However, when breakdown naturally occurred ahead of the mid-chord of the wing the vortices were found to be less sensitive to a probe placed behind the breakdown point. Vortex breakdown on a lower swept wing is found to be more sensitive to interference. Near the breakdown region, seven hole probe measurement is less accurate due to a combination of probe interference and flow reversal.

Payne, F. M.↗
NASA NTRS2001

Electro-Thermal Simulation Studies of SiC Junction Diodes Containing Screw Dislocations Under High Reverse-Bias Operation

The objective of this work was to conduct a modeling study of SiC P-N junction diodes operating under high reverse biased conditions. Analytical models and numerical simulation capabilities were to be developed for self-consistent electro-thermal analysis of the diode current-voltage (I-V) characteristics. Data from GRC indicate that screw dislocations are unavoidable in large area SiC devices, and lead to changes in the SiC diode electrical response characteristics under high field conditions. For example, device instability and failures linked to internal current filamentation have been observed. The physical origin of these processes is not well understood, and quantitative projections of the electrical behavior under high field and temperature conditions are lacking. Thermal calculations for SiC devices have not been reported in the literature either. So estimates or projections of peak device temperatures and power limitations do not exist. This numerical study and simulation analysis was aimed at resolving some of the above issues. The following tasks were successfully accomplished: (1) Development of physically based models using one- and two-dimensional drift-diffusion theory for the transport behavior and I-V characteristics; (2) One- and two-dimensional heat flow to account for internal device heating. This led to calculations of the internal temperature profiles, which in turn, were used to update the electrical transport parameters for a self-consistent analysis. The temperature profiles and the peak values were thus obtainable for a given device operating condition; (3) Inclusion of traps assumed to model the presence of internal screw dislocations running along the longitudinal direction; (4) Predictions of the operating characteristics with and without heating as a function of applied bias with and without traps. Both one and two-dimensional cases were implemented; (5) Assessment of device stability based on the operating characteristics. The presence of internal non-uniformities, particularly filamentary structures, was probed and demonstrated; (6) Cause and physical origins of filamentary behavior and unstable I-V characteristics were made transparent; (7) It was demonstrated that diodes containing defects would be more prone to thermal breakdown associated with the temperature dependent decrease in the thermal conductivity; and (8) Finally, negative differential resistance (S-shaped NDR) which can potential lead to device instability and filamentary behavior was shown to occur for diodes containing a line of defects such as could be associated with a screw dislocation line.

Joshi, R. P.↗
NASA NTRS2006

Jet Noise Diagnostics Supporting Statistical Noise Prediction Methods

The primary focus of my presentation is the development of the jet noise prediction code JeNo with most examples coming from the experimental work that drove the theoretical development and validation. JeNo is a statistical jet noise prediction code, based upon the Lilley acoustic analogy. Our approach uses time-average 2-D or 3-D mean and turbulent statistics of the flow as input. The output is source distributions and spectral directivity. NASA has been investing in development of statistical jet noise prediction tools because these seem to fit the middle ground that allows enough flexibility and fidelity for jet noise source diagnostics while having reasonable computational requirements. These tools rely on Reynolds-averaged Navier-Stokes (RANS) computational fluid dynamics (CFD) solutions as input for computing far-field spectral directivity using an acoustic analogy. There are many ways acoustic analogies can be created, each with a series of assumptions and models, many often taken unknowingly. And the resulting prediction can be easily reverse-engineered by altering the models contained within. However, only an approach which is mathematically sound, with assumptions validated and modeled quantities checked against direct measurement will give consistently correct answers. Many quantities are modeled in acoustic analogies precisely because they have been impossible to measure or calculate, making this requirement a difficult task. The NASA team has spent considerable effort identifying all the assumptions and models used to take the Navier-Stokes equations to the point of a statistical calculation via an acoustic analogy very similar to that proposed by Lilley. Assumptions have been identified and experiments have been developed to test these assumptions. In some cases this has resulted in assumptions being changed. Beginning with the CFD used as input to the acoustic analogy, models for turbulence closure used in RANS CFD codes have been explored and compared against measurements of mean and rms velocity statistics over a range of jet speeds and temperatures. Models for flow parameters used in the acoustic analogy, most notably the space-time correlations of velocity, have been compared against direct measurements, and modified to better fit the observed data. These measurements have been extremely challenging for hot, high speed jets, and represent a sizeable investment in instrumentation development. As an intermediate check that the analysis is predicting the physics intended, phased arrays have been employed to measure source distributions for a wide range of jet cases. And finally, careful far-field spectral directivity measurements have been taken for final validation of the prediction code. Examples of each of these experimental efforts will be presented. The main result of these efforts is a noise prediction code, named JeNo, which is in middevelopment. JeNo is able to consistently predict spectral directivity, including aft angle directivity, for subsonic cold jets of most geometries. Current development on JeNo is focused on extending its capability to hot jets, requiring inclusion of a previously neglected second source associated with thermal fluctuations. A secondary result of the intensive experimentation is the archiving of various flow statistics applicable to other acoustic analogies and to development of time-resolved prediction methods. These will be of lasting value as we look ahead at future challenges to the aeroacoustic experimentalist.

Bridges, James E.↗
NASA NTRS2016

Aerosol Meteorology of Maritime Continent for the 2012 7SEAS Southwest Monsoon Intensive Study - Part 2: Philippine Receptor Observations of Fine-Scale Aerosol Behavior

The largest 7 Southeast Asian Studies (7SEAS) operations period within the Maritime Continent (MC) occurred in the August-September 2012 biomass burning season. Data included were observations aboard the MY Vasco, dispatched to the Palawan Archipelago and Sulu Sea of the Philippines for September 2012. At these locations, the Vasco observed MC smoke and pollution entering the southwest monsoon (SWM) monsoonal trough. Here we describe the research cruise findings and the finer-scale aerosol meteorology of this convectively active region. This 2012 cruise complemented a 2-week cruise in 2011 and was generally consistent with previous findings in terms of how smoke emission and transport related to monsoonal flows, tropical cyclones (TC), and the covariance between smoke transport events and the atmosphere's thermodynamic structure. Biomass burning plumes were usually mixed with significant amounts of anthropogenic pollution. Also key to aerosol behavior were squall lines and cold pools propagating across the South China Sea (SCS) and scavenging aerosol particles in their path. However, the 2012 cruise showed much higher modulation in aerosol frequency than its 2011 counterpart. Whereas in 2011 large synoptic-scale aerosol events transported high concentrations of smoke into the Philippines over days, in 2012 measured aerosol events exhibited a much shorter-term variation, sometimes only 312h. Strong monsoonal flow reversals were also experienced in 2012. Nucleation events in cleaner and polluted conditions, as well as in urban plumes, were observed. Perhaps most interestingly, several cases of squall lines preceding major aerosol events were observed, as opposed to 2011 observations where these lines largely scavenged aerosol particles from the marine boundary layer. Combined, these observations indicate pockets of high and low particle counts that are not uncommon in the region. These perturbations are difficult to observe by satellite and very difficult to model. Indeed, the Navy Aerosol Analysis and Prediction System (NAAPS) simulations captured longer period aerosol events quite well but largely failed to capture the timing of high-frequency phenomena. Ultimately, the research findings of these cruises demonstrate the real world challenges of satellite-based missions, significant aerosol life cycle questions such as those the future Aerosol/Clouds/Ecosystems (ACE) will investigate, and the importance of small-scale phenomena such as sea breezes, squall lines, and nucleation events embedded within SWM patterns in dominating aerosol life cycle and potential relationships to clouds.

Reid, Jeffrey S.↗
NASA NTRSDate not supplied

Propulsion-Airframe Integration for Conceptual Redesign of a Low-Boom Supersonic Transport

A low-boom supersonic transport was designed for a cruise Mach of 1.7 and 40 passengers. This low-boom aircraft, referred to as the Mach 1.7 40-PAX concept, was generated using computational fluid dynamics (CFD) based sonic boom analysis at the start of overland cruise (SOC). The engine for the Mach 1.7 40-PAX concept was designed using the Numerical Propulsion System Simulation (NPSS) and modeled as a flow-through nacelle for CFD analysis. To understand how the engine plume affects the undertrack ground signature, the Mach 1.7 40-PAX concept is redesigned using an aeropropulsive CFD simulation. A process is developed for approximation of the NPSS engine at SOC by a CFD engine for aeropropulsive CFD simulation. The generated CFD engine has the identical nozzle boundary conditions and approximately the same mass flow and thrust as those of the NPSS engine at SOC. Then, the configuration with the CFD engines is optimized to approximately restore the low-boom characteristics of the Mach 1.7 40-PAX concept. Finally, the CFD simulation data for the optimized concept with the CFD engines is used to calibrate the low-fidelity aerodynamic analyses for mission analysis of this concept. The cyclic dependency of the involved disciplinary analyses is resolved using an iteration method for a consistent coupling of the mission analysis, NPSS engine analysis, and low-boom redesign using the aeropropulsive CFD simulation. This low-boom redesign study is used as an example to demonstrate how the propulsion-airframe integration could be implemented for conceptual design of low-boom supersonic transports.

Low-boom supersonic transport↗
NASA NTRSDate not supplied

Propulsion-Airframe Integration for Conceptual Redesign of a Low-Boom Supersonic Transport

A low-boom supersonic transport was designed for a cruise Mach of 1.7 and 40 passengers. This low-boom aircraft, referred to as the Mach 1.7 40-PAX concept, was generated using computational fluid dynamics (CFD) based sonic boom analysis at the start of overland cruise (SOC). The engine for the Mach 1.7 40-PAX concept was designed using the Numerical Propulsion System Simulation (NPSS) and modeled as a flow-through nacelle for CFD analysis. To understand how the engine plume affects the undertrack ground signature, the Mach 1.7 40-PAX concept is redesigned using an aeropropulsive CFD simulation. A process for approximation of the NPSS engine at SOC by a CFD engine is developed. The generated CFD engine has the identical nozzle boundary conditions and approximately the same mass flow and thrust as those of the NPSS engine at SOC. Then, the configuration with the CFD engines is optimized to approximately restore the low-boom characteristics of the Mach 1.7 40-PAX concept. Finally, the CFD simulation data for the optimized concept with the CFD engines is used to calibrate the low-fidelity aerodynamic analyses for mission analysis of this concept. The cyclic dependency of the involved disciplinary analyses is resolved using an iteration method for a consistent coupling of the mission analysis, NPSS engine analysis, and low-boom redesign using the aeropropulsive CFD simulation. This low-boom redesign study is used as an example to demonstrate how the propulsion-airframe integration could be implemented for conceptual design of low-boom supersonic transports.

Low-boom supersonic transport↗
NASA NTRS1951

Viscous Effects on Impact Probes in a Subsonic Rarified Gas Flow

The problem of time response of pressure gaging systems used with low density flows has been discussed in Ref ]4, and the effect of outgassing on pressure magnitudes was indicated in the same reference. Briefly, gases or vapors adhering to the internal walls of the pressure gaging system behave like gas sources and produce a pressure rise in the gage system which has no relation to the external flow. The effect can also occur in the reverse direction, with "in-gassing" or the action of an effective sink in the gage system as gases entering through the probe orifice are adsorbed to the walls. For given surface conditions, the magnitude of the pressure error to be expected due to out-gassing depends on the dimensions of the probe system. In the present tests, it was desirable to use the smallest possible probe to yield the lowest possible Reynolds number. The lower limit on size was fixed by outgassing effects, evaluated by the following procedure. 2.0 PROCEDURE The pumping system was adjusted to give a pressure, measured at the reservoir, of 9 microns Hg with no flow into the wind tunnel. The upstream metering valve was then opened and the air flow rate adjusted to give a pressure of 100 microns in the reservoir under steady flow conditions, The pressure read by one of the impact tubes, inserted into the flow, was measured. The upstream metering valve was then closed rapid)y, and the reservoir pressure, p0, and the impact probe pressure, Pj, were measured simultaneously at definite time intervals. Another probe was inserted into the flow and the procedure repeated, until the pressure-time data had been obtained for each probe investigated. The results for a series of tests Involving probe Nos.l, 2 and 3 are shown on HYD 2616 300 RESULTS From HYD 2616, It is clear that the smallest probe (No.3) requires the longest time to reach equilibrium. After a sufficient time has elapsed (about 180 seconds), this probe read the same, within the accuracy of measurement, as the other two, When a similar experiment was performed utilizing a probe which was one-half the size of probe No.2, it indicated a pressure, after 180 seconds, which was almost 10 microns Hg higher than the other probes. Accordingly, only probe Nos. 1, 2, 3 and 4 were employed in the experiments, and a time of at least 180 seconds was allowed to elapse between a change of setting and the reading of the instruments0

Kane, E. D.↗
NASA NTRS1998

Prediction of Transitional Flows in the Low Pressure Turbine

Current turbulence models tend to give too early and too short a length of flow transition to turbulence, and hence fail to predict flow separation induced by the adverse pressure gradients and streamline flow curvatures. Our discussion will focus on the development and validation of transition models. The baseline data for model comparisons are the T3 series, which include a range of free-stream turbulence intensity and cover zero-pressure gradient to aft-loaded turbine pressure gradient flows. The method will be based on the conditioned N-S equations and a transport equation for the intermittency factor. First, several of the most popular 2-equation models in predicting flow transition are examined: k-e [Launder-Sharina], k-w [Wilcox], Lien-Leschiziner and SST [Menter] models. All models fail to predict the onset and the length of transition, even for the simplest flat plate with zero-pressure gradient(T3A). Although the predicted onset position of transition can be varied by providing different inlet turbulent energy dissipation rates, the appropriate inlet conditions for turbulence quantities should be adjusted to match the decay of the free-stream turbulence. Arguably, one may adjust the low-Reynolds-number part of the model to predict transition. This approach has so far not been very successful. However, we have found that the low-Reynolds-number model of Launder and Sharma [1974], which is an improved version of Jones and Launder [1972] gave the best overall performance. The Launder and Sharma model was designed to capture flow re-laminarization (a reverse of flow transition), but tends to give rise to a too early and too fast transition in comparison with the physical transition. The three test cases were for flows with zero pressure gradient but with different free-stream turbulent intensities. The same can be said about the model when considering flows subject to pressure gradient(T3C1). To capture the effects of transition using existing turbulence models, one approach is to make use of the concept of the intermittency to predict the flow transition. It was originally based on the intermittency distribution of Narasimha [1957], and then gradually evolved into a transport equation for the intermittency factor. Gostelow and associates [1994,1995] have made some improvements to Narasimha's method in an attempt to account for both favorable and adverse pressure gradients. Their approach is based on a linear, explicit combination of laminar and turbulent solutions. This approach fails to predict the overshoot of the skin friction on a flat plate near the end of transition zone, even though the length of transition is well predicted. The major flaw of Gostelow's approach is that it assumes the non-turbulent part being the laminar solution and the turbulent part being the turbulent solution and they do not interact across the transitional region. The technique in condition averaging the flow equations in intermittent flows was first introduced by Libby [1975] and Dopazo [1977] and further refined by Dick and associates [1988, 1996]. This approach employs two sets of transport equations for the non-turbulent part and the other for the turbulent part. The advantage of this approach is that it allows the interaction of non-turbulent and turbulent velocities through the introduction of additional source terms in the continuity and momentum equations for the non-turbulent and turbulent velocities. However, the strong coupling of the two sets of equations has caused some numerical difficulties, which requires special attention. The prediction of the skin friction can be improved by this approach via the implicit coupling of non-turbulent and turbulent velocity flelds. Another improvement of the interrmittency model can be further made by allowing the intermittency to vary in the cross-stream direction. This is one step prior to testing any proposal for the transport equation for the intermittency factor. Instead of solving the transport equation for the intermittency factor, the distribution for the intermittency factor is prescribed by Klebanoff's empirical formula [1955]. The skin friction is very well predicted by this new modification, including the overshoot of the profile near the end of the transition zone. The outcome of this study is very encouraging since it indicates that the proper description of the intermittency distribution is the key to the success of the model prediction. This study will be used to guide us on the modelling of the intermittency transport equation.

Huang, George↗
NASA NTRS2023

Propulsion-Airframe Integration for Conceptual Redesign of a Low-Boom Supersonic Transport

A low-boom supersonic transport was generated in a previous low-boom multidisciplinary optimization (MDO) study that used computational fluid dynamics (CFD) off-body pressure to compute the undertrack sonic boom ground signature and calibrated low-fidelity aerodynamics analyses to compute the mission performance metrics. This low-boom aircraft, referred to as the Mach 1.7 40-PAX concept, can carry 40 passengers for a low-boom overland mission with cruise Mach 1.7 for the airport pairs over the continental US and has the potential to achieve an undertrack sonic boom ground noise level below 70 perceived level of decibels at the start of overland cruise (SOC). The engine for the Mach 1.7 40-PAX concept was designed using the Numerical Propulsion System Simulation (NPSS) for the mission analysis and modeled as a flow-through nacelle for CFD-based sonic boom analysis. To understand how the engine plume affects the undertrack ground signature, the Mach 1.7 40-PAX concept is redesigned in this paper after replacing the flow-through nacelles by CFD engines for sonic boom analysis using aeropropulsive CFD simulation. A process is developed for approximation of the NPSS engine at SOC by a CFD engine for aeropropulsive CFD simulation. The generated CFD engine has the identical nozzle boundary conditions and approximately the same mass flow and thrust as those of the NPSS engine at SOC. Then, the outer mold line of the configuration with the CFD engines is redesigned to approximately restore the low-boom characteristics of the Mach 1.7 40-PAX concept at SOC. Finally, the CFD simulation data for the redesigned concept with the CFD engines is used to calibrate the low-fidelity aerodynamic analyses for mission analysis of this concept. The cyclic dependency of the involved disciplinary analyses is resolved using an iteration method for a consistent coupling of the mission analysis, NPSS engine analysis, and low-boom redesign using the aeropropulsive CFD simulation. This low-boom redesign study is used as an example to demonstrate how the propulsion-airframe integration could be implemented for conceptual design of supersonic transports that satisfy both the low-boom and mission performance requirements.

Low-boom supersonic transport↗
NASA NTRS2016

Fluid Shifts

NASA is focusing on long-duration missions on the International Space Station (ISS) and future exploration-class missions beyond low-Earth orbit. Visual acuity changes observed after short-duration missions were largely transient, but more than 50% of ISS astronauts experienced more profound, chronic changes with objective structural and functional findings such as papilledema and choroidal folds. Globe flattening, optic nerve sheath dilation, and optic nerve tortuosity also are apparent. This pattern is referred to as the visual impairment and intracranial pressure (VIIP) syndrome. VIIP signs and symptoms, as well as postflight lumbar puncture data, suggest that elevated intracranial pressure (ICP) may be associated with the spaceflight-induced cephalad fluid shifts, but this hypothesis has not been tested. The purpose of this study is to characterize fluid distribution and compartmentalization associated with long-duration spaceflight, and to correlate these findings with vision changes and other elements of the VIIP syndrome. We also seek to determine whether the magnitude of fluid shifts during spaceflight, as well as the VIIP-related effects of those shifts, is predicted by the crewmember's preflight conditions and responses to acute hemodynamic manipulations (such as head-down tilt). Lastly, we will evaluate the patterns of fluid distribution in ISS astronauts during acute reversal of fluid shifts through application of lower body negative pressure (LBNP) interventions to characterize and explain general and individual responses. METHODS: We will examine a variety of physiologic variables in 10 long-duration ISS crewmembers using the test conditions and timeline presented in the Figure below. Measures include: (1) fluid compartmentalization (total body water by D2O, extracellular fluid by NaBr, intracellular fluid by calculation, plasma volume by CO rebreathe, interstitial fluid by calculation); (2) forehead/eyelids, tibia, calcaneus tissue thickness (by ultrasound); (3) vascular dimensions by ultrasound (jugular veins, cerebral and carotid arteries, vertebral arteries and veins, portal vein); (4) vascular dynamics by MRI (head/neck blood flow, cerebrospinal fluid pulsatility); (5) ocular measures (optical coherence tomography, intraocular pressure, 2-dimensional ultrasound including optic nerve sheath diameter, globe flattening, and retina-choroid thickness, Doppler ultrasound of ophthalmic and retinal arteries, and veins); (6) cardiac variables by ultrasound (inferior vena cava, tricuspid flow and tissue Doppler, pulmonic valve, stroke volume, right heart dimensions and function, four-chamber views); and (7) ICP measures (tympanic membrane displacement, distortion-product otoacoustic emissions, and ICP calculated by MRI). On the ground, acute head-down tilt will induce cephalad fluid shifts, whereas LBNP will oppose these shifts. Controlled Mueller maneuvers will manipulate cardiovascular variables. Through interventions applied before, during, and after flight, we intend to fully evaluate the relationship between fluid shifts and the VIIP syndrome.

Stenger, M.↗
NASA NTRS1998

The Local ISM and its Interaction with the Winds of Nearby Late-type Stars

We present new Goddard High-Resolution Spectrograph (GHRS) observations of the Ly-alpha and Mg II absorption lines seen toward the nearby stars 61 Cyg A and 40 Eri A. We use these data to measure interstellar properties along these lines of sight and to search for evidence of circumstellar hydrogen walls, which are produced by collisions between the stellar winds and the Local InterStellar Medium (LISM). We were able to model the Ly-alpha lines of both stars without hydrogen-wall absorption components, but for 61 Cyg A the fit required a stellar Ly-alpha, line profile with an improbably deep self-reversal, and for 40 Eri A the fit required a very low deuterium-to-hydrogen ratio that is inconsistent with previous GHRS measurements. Since these problems could be rectified simply by including stellar hydrogen-wall components with reasonable attributes, our preferred fits to the data include these components. We have explored several ways in which the hydrogen-wall properties measured here and in previous work can be used to study stellar winds and the LISM. We argue that the existence of a hydrogen wall around 40 Eri A and a low H I column density along that line of sight imply that either the interstellar density must decrease toward 40 Eri A or the hydrogen ionization fraction (chi) must increase. We find that hydrogen-wall temperatures are larger for stars with faster velocities through the LISM. The observed temperature-velocity relation is consistent with the predictions of hydromagnetic shock jump conditions. More precise comparison of the data and the jump conditions suggests crude upper limits for both chi and the ratio of magnetic to thermal pressure in the LISM (alpha): chi less than 0.6 and alpha less than 2. The latter upper limit corresponds to a limit on the LISM magnetic field of B less than 5 micro G. These results imply that the plasma Mach number of the interstellar wind flowing into the heliosphere is M(sub A) greater than 1.3, which indicates that the collision is supersonic and that there should therefore be a bow shock outside the heliopause in the upwind direction. Finally, we estimate stellar wind pressures (P sub wind) from the measured hydrogen-wall column densities. These estimates represent the first empirical measurements of wind properties for late-type main-sequence stars. The wind pressures appear to be correlated with stellar X-ray surface fluxes, F(x), in a manner consistent with the relation P(wind) varies as F(x)(exp -1/2), a relation that is also consistent with the variations of P(sub wind) and F(sub x) observed during the solar activity cycle. If this relation can in fact be generalized to solar-like stars, as is suggested by our data, then it is possible to estimate stellar wind properties simply by measuring stellar X-rays. One implication of this is that stellar wind pressures and mass-loss rates are then predicted to increase with time, since F(sub x) is known to decrease with stellar age.

Wood, Brian E.↗
NASA NTRS2000

Does Warming a Lysozyme Solution Cook Ones Data?

Chicken egg white lysozyme has a well characterized thermally driven phase transition. Between pH 4.0 and 5.2, the transition temperature, as defined by the point where the tetragonal and orthorhombic solubility are equal, is a function of the pH, salt (precipitant) type and concentration, and most likely of the buffer concentration as well. This phase transition can be carried out with protein solution alone, prior to the initiation of the crystallization process. We have now measured the kinetics of this process and investigated its reversibility. An aliquot of a stock protein solution is held at a given temperature, and at periodic intervals used to set up batch crystallization experiments. The batch solutions were incubated at 20 C until macroscopic crystals were obtained, at which point the number of crystals in each well were counted. The transition effects increased with temperature, slowly falling off at 30 C with a half time (time to approx. 1/2 the t = 0 number of crystals) of approx. 5 hours, and an estimated half time of approx. 0.5 hours at 43 C. Further, the process was not reversible by simple cooling. After holding a lysozyme solution at 37 C (prior to addition of precipitant) for 16 hours, then cooling and holding it at 4 C, no return to the pre-warmed nucleation kinetics are observed after at least 4 weeks. Thus every thermal excursion above the phase transition point results in a further decrease in the nucleation rate of that solution, the extent being a function of the time and temperature. Orthorhombic lysozyme crystals apparently do not undergo the flow-induced growth cessation of tetragonal lysozyme crystals. We have previously shown that putting the protein in the orthorhombic form does not affect the averaged face growth kinetics, only nucleation, for tetragonal crystals. We may be able to use this differential behavior to elucidate how flow affects tile lysozyme crystal growth process.

Pusey, Marc↗
NASA NTRS2014

Fluid Shifts

NASA is focusing on long-duration missions on the International Space Station (ISS) and future exploration-class missions beyond low Earth orbit. Visual acuity changes observed after short-duration missions were largely transient, but more than 30% of ISS astronauts experience more profound, chronic changes with objective structural and functional findings such as papilledema and choroidal folds. Globe flattening, optic nerve sheath dilation, and optic nerve tortuosity also are apparent. This pattern is referred to as the visual impairment and intracranial pressure (VIIP) syndrome. VIIP signs and symptoms, as well as postflight lumbar puncture data, suggest that elevated intracranial pressure (ICP) may be associated with the space flight-induced cephalad fluid shifts, but this hypothesis has not been tested. The purpose of this study is to characterize fluid distribution and compartmentalization associated with long-duration space flight, and to correlate these findings with vision changes and other elements of the VIIP syndrome. We also seek to determine whether the magnitude of fluid shifts during space flight, as well as the VIIP-related effects of those shifts, is predicted by the crewmember's pre-flight condition and responses to acute hemodynamic manipulations (such as head-down tilt). Lastly, we will evaluate the patterns of fluid distribution in ISS astronauts during acute reversal of fluid shifts through application of lower body negative pressure (LBNP) interventions to characterize and explain general and individual responses. We will examine a variety of physiologic variables in 10 long-duration ISS crewmembers using the test conditions and timeline presented in the Figure below. Measures include: (1) fluid compartmentalization (total body water by D2O, extracellular fluid by NaBr, intracellular fluid by calculation, plasma volume by CO rebreathe, interstitial fluid by calculation); (2) forehead/eyelids, tibia, calcaneus tissue thickness (by ultrasound); (3) vascular dimensions by ultrasound (jugular veins, cerebral and carotid arteries, vertebral arteries and veins, portal vein); (4) vascular dynamics by MRI (head/neck blood flow, cerebrospinal fluid pulsatility); (5) ocular measures (optical coherence tomography, intraocular pressure, 2-dimensional ultrasound including optic nerve sheath diameter, globe flattening, and retina-choroid thickness, Doppler ultrasound of ophthalmic and retinal arteries, and veins); (6) cardiac variables by ultrasound (inferior vena cava, tricuspid flow and tissue Doppler, pulmonic valve, stroke volume, right heart dimensions and function, four-chamber views); and (7) ICP measures (tympanic membrane displacement, distortion-product otoacoustic emissions, and ICP calculated by MRI). On the ground, acute head-down tilt will induce cephalad fluid shifts, whereas LBNP will oppose these shifts. Controlled Mueller maneuvers will manipulate cardiovascular variables. Through interventions applied before, during, and after flight, we intend to fully evaluate the relationship between fluid shifts and the VIIP syndrome. This study has been selected for flight implementation and is one of the candidate investigations being considered for the one year mission.

Stenger, Michael↗
NASA NTRSDate not supplied

Enhancements to Linear Stability-Based, CFD-integrated Transition Prediction for High-Speed Flows

Combining linear stability calculations with computational fluid dynamics (CFD) simulations has great potential for the automated modeling of high-speed flows, especially when adequate information about the configuration and the disturbance environment is available. However, a significant impediment to the applicability of this technique is the lack of an efficient method to calculate the crucial amplification ratio corresponding to the onset of transition in hypersonic flows. This ratio, also known as the "transition N-factor," is dependent upon the freestream disturbance environment as well as the surface properties of the test article. In response to the need for an engineering solution to predict the transition N-factor within conventional hypersonic wind tunnels, this paper presents a data-driven correlation that expands the existing correlations from straight circular cones with a narrow range of half angles to a broader array of axisymmetric configurations. Furthermore, when tested against a chosen dataset that was not used in its calibration, the suggested correlation shows good predictive accuracy with an RMS error of only 6.9%. Although similar accuracy may also be achieved via existing correlations based on similar datasets, predictions based on the proposed correlation have the advantage of not requiring an extensive amount of configuration-specific data. Practical applications often have access to the input parameters needed for this correlation, such as the freestream disturbance intensity, Mach number, and body-based slenderness Reynolds number. Additionally, this correlation outperforms the traditional assumption of a constant N-factor, particularly for configurations with blunted nose geometries. The development of this correlation is grounded in an extensive dataset encompassing conical models with body half-angles varying between 5 degrees and 16 degrees, Mach numbers ranging from 5 to 14, and nosetip-based Reynolds numbers approaching the transition reversal limit for blunt-nosed cones.

CFD↗