SEARCH · Engineering Papers

Results for “Cross Section generation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS2001

Supersonic Wind Tunnel Tests of a Half-axisymmetric 12 Deg-spike Inlet to a Rocket-based Combined-cycle Propulsion System

Results of an isolated inlet test for NASA's GTX air-breathing launch vehicle concept are presented. The GTX is a Vertical Take-off/ Horizontal Landing reusable single-stage-to-orbit system powered by a rocket-based combined-cycle propulsion system. Tests were conducted in the NASA Glenn 1- by 1-Foot Supersonic Wind Tunnel during two entries in October 1998 and February 1999. Tests were run from Mach 2.8 to 6. Integrated performance parameters and static pressure distributions are reported. The maximum contraction ratios achieved in the tests were lower than predicted by axisymmetric Reynolds-averaged Navier-Stokes computational fluid dynamics (CFD). At Mach 6, the maximum contraction ratio was roughly one-half of the CFD value of 16. The addition of either boundary-layer trip strips or vortex generators had a negligible effect on the maximum contraction ratio. A shock boundary-layer interaction was also evident on the end-walls that terminate the annular flowpath cross section. Cut-back end-walls, designed to reduce the boundary-layer growth upstream of the shock and minimize the interaction, also had negligible effect on the maximum contraction ratio. Both the excessive turning of low-momentum comer flows and local over-contraction due to asymmetric end-walls were identified as possible reasons for the discrepancy between the CFD predictions and the experiment. It is recommended that the centerbody spike and throat angles be reduced in order to lessen the induced pressure rise. The addition of a step on the cowl surface, and planar end-walls more closely approximating a plane of symmetry are also recommended. Provisions for end-wall boundary-layer bleed should be incorporated.

DeBonis, J. R.↗

NASA NTRS1993

Investigation of High-alpha Lateral-directional Control Power Requirements for High-performance Aircraft

Designers of the next-generation fighter and attack airplanes are faced with the requirements of good high-angle-of-attack maneuverability as well as efficient high speed cruise capability with low radar cross section (RCS) characteristics. As a result, they are challenged with the task of making critical design trades to achieve the desired levels of maneuverability and performance. This task has highlighted the need for comprehensive, flight-validated lateral-directional control power design guidelines for high angles of attack. A joint NASA/U.S. Navy study has been initiated to address this need and to investigate the complex flight dynamics characteristics and controls requirements for high-angle-of-attack lateral-directional maneuvering. A multi-year research program is underway which includes ground-based piloted simulation and flight validation. This paper will give a status update of this program that will include a program overview, description of test methodology and preliminary results.

Foster, John V.↗

NASA NTRS2017

Fabrication of the HIAD Large-Scale Demonstration Assembly and Upcoming Mission Applications

Over a decade of work has been conducted in the development of NASAs Hypersonic Inflatable Aerodynamic Decelerator (HIAD) technology. This effort has included multiple ground test campaigns and flight tests culminating in the HIAD projects second generation (Gen-2) deployable aeroshell system and associated analytical tools. NASAs HIAD project team has developed, fabricated, and tested inflatable structures (IS) integrated with flexible thermal protection system (F-TPS), ranging in diameters from 3-6m, with cone angles of 60 and 70 deg.In 2015, United Launch Alliance (ULA) announced that they will use a HIAD (10-12m) as part of their Sensible, Modular, Autonomous Return Technology (SMART) for their upcoming Vulcan rocket. ULA expects SMART reusability, coupled with other advancements for Vulcan, will substantially reduce the cost of access to space. The first booster engine recovery via HIAD is scheduled for 2024. To meet this near-term need, as well as future NASA applications, the HIAD team is investigating taking the technology to the 10-15m diameter scale.In the last year, many significant development and fabrication efforts have been accomplished, culminating in the construction of a large-scale inflatable structure demonstration assembly. This assembly incorporated the first three tori for a 12m Mars Human-Scale Pathfinder HIAD conceptual design that was constructed with the current state of the art material set. Numerous design trades and torus fabrication demonstrations preceded this effort. In 2016, three large-scale tori (0.61m cross-section) and six subscale tori (0.25m cross-section) were manufactured to demonstrate fabrication techniques using the newest candidate material sets. These tori were tested to evaluate durability and load capacity. This work led to the selection of the inflatable structures third generation (Gen-3) structural liner. In late 2016, the three tori required for the large-scale demonstration assembly were fabricated, and then integrated in early 2017. The design includes provisions to add the remaining four tori necessary to complete the assembly of the 12m Human-Scale Pathfinder HIAD in the event future project funding becomes available.This presentation will discuss the HIAD large-scale demonstration assembly design and fabrication per-formed in the last year including the precursor tori development and the partial-stack fabrication. Potential near-term and future 10-15m HIAD applications will also be discussed.

Swanson, G. T.↗

NASA NTRS2017

Fabrication of the HIAD Large-Scale Demonstration Assembly

Over a decade of work has been conducted in the development of NASA's Hypersonic Inflatable Aerodynamic Decelerator (HIAD) technology. This effort has included multiple ground test campaigns and flight tests culminating in the HIAD projects second generation (Gen-2) deployable aeroshell system and associated analytical tools. NASAs HIAD project team has developed, fabricated, and tested inflatable structures (IS) integrated with flexible thermal protection system (F-TPS), ranging in diameters from 3-6m, with cone angles of 60 and 70 deg.In 2015, United Launch Alliance (ULA) announced that they will use a HIAD (10-12m) as part of their Sensible, Modular, Autonomous Return Technology (SMART) for their upcoming Vulcan rocket. ULA expects SMART reusability, coupled with other advancements for Vulcan, will substantially reduce the cost of access to space. The first booster engine recovery via HIAD is scheduled for 2024. To meet this near-term need, as well as future NASA applications, the HIAD team is investigating taking the technology to the 10-15m diameter scale. In the last year, many significant development and fabrication efforts have been accomplished, culminating in the construction of a large-scale inflatable structure demonstration assembly. This assembly incorporated the first three tori for a 12m Mars Human-Scale Pathfinder HIAD conceptual design that was constructed with the current state of the art material set. Numerous design trades and torus fabrication demonstrations preceded this effort. In 2016, three large-scale tori (0.61m cross-section) and six subscale tori (0.25m cross-section) were manufactured to demonstrate fabrication techniques using the newest candidate material sets. These tori were tested to evaluate durability and load capacity. This work led to the selection of the inflatable structures third generation (Gen-3) structural liner. In late 2016, the three tori required for the large-scale demonstration assembly were fabricated, and then integrated in early 2017. The design includes provisions to add the remaining four tori necessary to complete the assembly of the 12m Human-Scale Pathfinder HIAD in the event future project funding becomes available.This presentation will discuss the HIAD large-scale demonstration assembly design and fabrication per-formed in the last year including the precursor tori development and the partial-stack fabrication. Potential near-term and future 10-15m HIAD applications will also be discussed.

Swanson, G. T.↗

NASA NTRS2021

Magnetic Reconnection in a Sheared Magnetic Flux Tube: Slippage Versus Tearing

The process of magnetic reconnection in a flux tube can occur in a time-stationary fashion as slippage reconnection or in a time-dependent manner based on, for example, the tearing instability. However, it is not well known under which conditions a system can sustain slippage reconnection. Likewise, it is unclear whether systems can exhibit slippage reconnection and time-dependent reconnection simultaneously. In order to investigate these questions, we employ a set of 3D magnetohydrodynamic simulation. Using these simulations, we model a twisted flux tube with a spatially localized resistive region in the center of the simulation box, and an applied driver on one end plane of the simulation box. As a result, the Poynting flux injected at the boundary propagates to the resistive region and dissipates there. If the driver is nearly circular, we find a predominance of slippage reconnection, which decouples the applied driver entirely from one half of the flux tube. Second, a tearing-like instability occurs with slippage reconnection in the resistive region when the resistivity is strong enough and the cross section of the flux tube, as defined by the shape of the applied velocity perturbation, is elliptical enough. In this case we find the surprising feature that magnetic field perturbation generated by the tearing-like instability radiates away from the resistive region to influence the entire flux tube shape.

Hidetaka Kuniyoshi↗

NASA NTRS1980

An ultrasonic plethysmograph for space flight applications

The development of an ultrasonic plethysmograph based on the transit time measurement principle is reported, which meets the space-imposed requirements for evaluating cardiovascular deconditioning. It consists of a pulse generator, pulse receiver amplifier, voltage comparator, synchronous pulse generator, elapsed time counter, and transmit and receive piezoelectric crystals resonant at 2 MHz and of 3 mm diameter. The transit time for an ultrasonic pulse to propagate across a limb cross section is computed in a digital fashion using a 32 MHz clock, and resolution is 0.049 mm with the range being approximately 200 mm. Experimental results regarding dynamic system response were found comparable in both accuracy and sensitivity to those of a Whitney strain gage using a 50 torr venous occlusion.

Bhagat, P. K.↗

NASA NTRS1984

A current generation by Compton scattering in a relativistic plasma with velocity shear and temperature gradient

Current generation by Thomson scattering in a non-relativistic plasma with the velocity shear and the temperature gradient (Hinata and Daneshvar, 1983) is extended to a relativistic plasma by replacing Thomson cross section by the Klein-Nishina formula. Because of the energy dependence of the cross-section, a numerical rather than analytic result is presented. The present calculation may be applied to a supernova implosion where the temperature may reach several MeV and a strong differential rotation is expected. It may also find applications in the early universe, and laser-pellet interaction.

Hinata, S.↗

NASA NTRSDate not supplied

Alignment and Verification Testing of the GPS LRA Test Bed

The LRCTF (Laser Ranging Characterization and Test Facility) is a unique facility built at NASA GSFC to provide thermal-optical testing of the next generation GPS LRA (Global Positioning Satellite’s Laser Retroreflector Array) laser ranging target. The 400mm diameter target is an array consisting of 48 total internal reflection retroreflectors and has an optical cross section requirement of 100 MSM (million square meters). To verify that the array meets this requirement during on-orbit conditions, the LRCTF is equipped with a 400mm test beam, a data product output consisting of full aperture FFDPs (Far Field Diffraction Patterns) and a thermal chamber. The FFDPs are used to calculate the OCS. This paper will describe the facility design, alignment approach, and verification process.

Patricia Lyons↗

NASA NTRSDate not supplied

Fluidic Fence Flow Control on A 30° Swept Wing in Compressible Freestreams

A 30° swept wing with a NACA 64(3)-618 airfoil cross-section was evaluated in four different freestream conditions with Mach numbers increasing from 0.05 to 0.7 using computational fluid dynamics simulations. Active flow control (AFC) through a streamwise row of vortex generating jets was applied at 70% span, blowing inboard to obstruct the development of spanwise flow and increase lift outboard of the control location. The effectiveness of the AFC was evaluated at α = 5° and 10° as freestream Mach number increased and the AFC mass flow coefficient was held constant. Increases to lift coefficient were reduced at higher Mach numbers, but the ratio of change in lift coefficient and the AFC momentum coefficient remained roughly constant. The fluidic fence caused decreased pressure coefficients on the outboard wing sections, but this region of decreased pressure coefficient moved aft on the chord with increasing Mach number. Mach 0.7 is higher than the critical Mach number of the wing and produced interesting interplay with the AFC, as the suction surface shock moved forward on the inboard wing section but moved aft on the outboard wing section.

Evan J McFadden↗

NASA NTRSDate not supplied

Fluidic Fence Flow Control on A 30° Swept Wing in Compressible Freestreams

Evan J McFadden↗

NASA NTRS1994

The Monostatic/Bistatic Approximation

Many Radar Cross Section (RCS) prediction codes are limited to one monostatic return per run. However, such codes can calculate multiple bistatic returns per incident angle for a relatively small amount of additional computer resources. This note describes a method of using bistatic returns to generate multiple monostatic predictions for each incident angle computed. Typical results are presented and show the accuracy is initially good and then degrades as the separation angle between the incident and viewing angles becomes large. Introduction Since 1990, the monostatic/bistatic approximation has been used to reduce the number of runs required by finite-volume time-domain (FVTD) codes for making RCS versus azimuth plots. This approximation was spawned by the observation of a range test where the transmit and receive antennas were separated by a few degrees to prevent cross talk between the antennas. The measurements from this range are presented as monostatic RCS rather than bistatic: RCS. The procedure of reporting experimental bistatic RCS as the monostatic RCS at the angle bisecting the transmit and receive antennas was extended to FVTD codes and produces excellent results.

Schuh, Michael J.↗

NASA NTRS1991

Interaction of two glancing, crossing shock waves with a turbulent boundary-layer at various Mach numbers

A preliminary experimental investigation was conducted to study two crossing, glancing shock waves of equal strengths, interacting with the boundary-layer developed on a supersonic wind tunnel wall. This study was performed at several Mach numbers between 2.5 and 4.0. The shock waves were created by fins (shock generators), spanning the tunnel test section, that were set at angles varying from 4 to 12 degrees. The data acquired are wall static pressure measurements, and qualitative information in the form of oil flow and schlieren visualizations. The principle aim is two-fold. First, a fundamental understanding of the physics underlying this flow phenomena is desired. Also, a comprehensive data set is needed for computational fluid dynamic code validation. Results indicate that for small shock generator angles, the boundary-layer remains attached throughout the flow field. However, with increasing shock strengths (increasing generator angles), boundary layer separation does occur and becomes progressively more severe as the generator angles are increased further. The location of the separation, which starts well downstream of the shock crossing point, moves upstream as shock strengths are increased. At the highest generator angles, the separation appears to begin coincident with the generator leading edges and engulfs most of the area between the generators. This phenomena occurs very near the 'unstart' limit for the generators. The wall pressures at the lower generator angles are nominally consistent with the flow geometries (i.e. shock patterns) although significantly affected by the boundary-layer upstream influence. As separation occurs, the wall pressures exhibit a gradient that is mainly axial in direction in the vicinity of the separation. At the limiting conditions the wall pressure gradients are primarily in the axial direction throughout.

Hingst, Warren R.↗

NASA NTRS1992

Finite difference time domain grid generation from AMC helicopter models

A simple technique is presented which forms a cubic grid model of a helicopter from an Aircraft Modeling Code (AMC) input file. The AMC input file defines the helicopter fuselage as a series of polygonal cross sections. The cubic grid model is used as an input to a Finite Difference Time Domain (FDTD) code to obtain predictions of antenna performance on a generic helicopter model. The predictions compare reasonably well with measured data.

Cravey, Robin L.↗

NASA NTRS1995

Designing A Mode Converter For Use With A Gyrotron

Report describes process of designing corrugated, circular-cross-section length of waveguide converting input electromagnetic radiation at frequency of 34.5 GHz in TM(11) mode to output radiation in HE(11) mode. TM(11)-mode input radiation supplied by gyrotron generating continuous-wave power of 200 kW at 34.5 GHz in TE(01) mode followed by TE(01)-to-TM(11) mode converter. Together, gyrotron and mode converters constitute prototype high-power transmitter for long-distance free-space communication.

Hoppe, Daniel J.↗

NASA NTRS2018

Titan's Cold Case Files - Outstanding Questions After Cassini-Huygens

The entry of the Cassini-Huygens spacecraft into orbit around Saturn in July 2004 marked the start of a golden era in the exploration of Titan, Saturn's giant moon. During the prime mission (2004-2008), ground-breaking discoveries were made by the Cassini orbiter including the equatorial dune fields (flyby T3, 2005), northern lakes and seas (T16, 2006), and the large positive and negative ions (T16 & T18, 2006), to name a few. In 2005 the Huygens probe descended through Titan's atmosphere, taking the first close-up pictures of the surface, including large networks of dendritic channels leading to a dried-up seabed, and also obtaining detailed profiles of temperature and gas composition during the atmospheric descent. The discoveries continued through the Equinox mission (2008-2010) and Solstice mission (2010-2017) totaling 127 targeted flybys of Titan in all. Now at the end of the mission, we are able to look back on the high-level scientific questions from the start of the mission, and assess the progress that has been made towards answering these. At the same time, new scientific questions regarding Titan have emerged from the new discoveries that have been made. In this paper we review a cross-section of important scientific questions that remain partially or completely unanswered, ranging from Titan's deep interior to the exosphere. Our intention is to help formulate the science goals for the next generation of planetary missions to Saturn and Titan, and to stimulate new experimental, observation and theoretical investigations in the interim, before such missions arrive again at Titan.

Nixon, C. A.↗

NASA NTRS1986

Beam-plasma instabilities and the beam-plasma discharge

Using a new waves on magnetized beams and turbulence (WOMBAT) 0-450 eV electron gun, measurements bearing on the generation of beam-plasma discharge (BPD) are made. The new gun has a narrower divergence angle than the old, and the BPD ignition current is found to be proportional to the cross-sectional area of the plasma. The high-frequency instabilities are identified with the two Trivelpiece-Gould modes, (1959). The upper frequency is identified as a Cerenkov resonance with the upper Trivelpiece-Gould mode, and the lower frequency with a cyclotron resonance with the lower mode, in agreement with theoretical expectations. Convective growth rates are found to be small. A mechanism involving the conversion of a convective instability to an absolute one by trapping of the unstable waves in the density perturbations of the low-frequency waves, is suggested for the low-frequency wave control of the onset of the high frequency precursors to the BPD.

Kellogg, P. J.↗

NASA NTRS2003

Autotrophic Ecosystems on the Early Earth

Ophiolite sequences, sections of lower oceanic crust and upper mantle that have been thrust onto continental craton, are located in northern and central California and provide easily accessible areas that serve as good analogs for similar, more extensive areas of the early Earth. We have begun investigating and characterizing these sites in order to understand better the processes that may be responsible for the water chemistry, mineralogy and biology of similar environments on the early Earth. The geophysical and geochemical processes in these terranes provide niches for unique communities of extremeophiles and likely provide a good analog to the location that first gave rise to life on Earth. The ophiolites found in northern and central California include the Trinity, Josephine, Coast Range and Point Sal, all of which are approximately 160 million years old. Fluids from serpentinizing springs are generally alkaline with high pH and H2 contents, indicating that the mafic rock compositions control the fluid composition through water-rock reactions during relatively low-grade hydrothermal processes. There are significant amounts of primary mineralogy remaining in the rocks, meaning that substantial alteration processes are still occurring in these terranes. The general reaction for serpentinization of olivine is given by one of the authors. olivine + H2O = serpentine + brucite + magnetite + H2. We have analyzed the mineralogical composition of several rock samples collected from the Coast Range Ophiolite near Clear Lake, CA by electron microprobe. The remnant primary mineralogy is fairly urnform in composition, with an olivine composition of Fo(sub 90), and with pyroxene compositions of En(sub 90) for orthopyroxene and En(sub 49)Wo(sub 48)Fs(sub 03) for the clinopyroxene. Other primary phases observed include chromites and other spinels. Examination of petrographic thin sections reveals that serpentinization reactions have occurred in these locations. The serpentine resulting from aqueous alteration of olivine resides in veins that are see to cross cut the primary mineral grains. There are several generations of alteration products, comprised mostly of serpentines that are magnesium rich, with magnetite, brucite and carbonates observed as accessory minerals. The formation of carbonates can be taken to indicate the presence of CO2 in the altering fluids. We collected samples from a spring in the Coast Range Ophiolite in order to determine whether the geochemical environment serves as a habitat for chemotrophic microorganisms. DNA was extracted from the sediment samples and the 16s rRNA gene was PCR amplified using universal Archaeal primers. Denaturing gradient gel electrophoresis (DGGE) was used to determine the community of Archaea thriving in these samples. Our results indicate that there were 8 different genera of Archaea from a single sample. A sequence was obtained from one of these eight. The sequence is of an organism similar to Halorubrum tibetense, and alkalophilic Archaeon. This result suggests that these environments are likely hosts for communities of organisms that are adapted for the unique chemistry provided by the alkaline spring.

Schulte, M.↗

NASA NTRS2005

An Algorithm for the Transport of Anisotropic Neutrons

One major obstacle to human space exploration is the possible limitations imposed by the adverse effect of long-term exposure to the space environment. Even before human spaceflight began, the potentially brief exposure of astronauts to the very intense random solar particle events (SPE) were of great concern. A new challenge appears in deep space exploration from exposure to the low-intensity heavy-ion flux of the galactic cosmic rays (GCR) since the missions are of long duration and the accumulated GCR exposures can be high. Because cancer induction rates increase behind low to rather large thicknesses of aluminum shielding, according to available biological data on mammalian exposures to GCR like ions, the shield requirements for a Mars mission are prohibitively expensive in terms of mission launch costs. Therefore, a critical issue in the Human Exploration and Development of Space enterprise is cost effective mitigation of risk associated with ionizing radiation exposure. In order to estimate astronaut risk to GCR exposure and associated cancer risks and health hazards, it is necessary to do shield material studies. To determine an optimum radiation shield material it is necessary to understand nuclear interaction processes such as fragmentation and secondary particle production which is a function of energy dependent cross sections. This requires knowledge of material transmission characteristics either through laboratory testing or improved theoretical modeling. Here ion beam transport theory is of importance in that testing of materials in the laboratory environment generated by particle accelerators is a necessary step in materials development and evaluation for space use. The approximations used in solving the Boltzmann transport equation for the space setting are often not sufficient for laboratory work and those issues are a major emphasis of the present work.

Tweed, J.↗