SEARCH · Engineering Papers

Results for “Configurations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Effects of deflected thrust on the longitudinal aerodynamic characteristics of a close-coupled wing-canard configuration

The effects of power on the longitudinal aerodynamic characteristics of a close-coupled wing-canard fighter configuration with partial-span rectangular nozzles at the trailing edge of the wing were investigated. Data were obtained on a basic wing-strake configuration for nozzle and flap deflections from 0 deg to 30 deg and for nominal thrust coefficients from 0 to 0.30. The model was tested over an angle-of-attack range from -2 deg to 40 deg at Mach numbers of 0.15 and 0.18. Results show substantial improvements in lift-curve slope, in maximum lift, and in drag-due-to-lift efficiency when the canard and strakes have been added to the basic wing-fuselage (wing-alone) configuration. Addition of power increased both lift-curve slope and maximum lift, improved longitudinal stability, and reduced drag due to lift on both the wing-canard and wing-canard-strake configurations. These beneficial effects are primarily derived from boundary-layer control due to moderate thrust coefficients which delay flow separation on the nozzle and inboard portion of the wing flaps.

Yip, L. P.↗

NASA NTRS1978

Investigation of the burning configuration of a coaxial injector in a combustion chamber

An analytical investigation was made into the stability of the burning configuration of a single coaxial injector surrounded by similar injectors. The stability criteria was based on an average pressure difference along the boundaries of the adjacent stream tubes as calculated using Spaulding's numerical method. The results indicate qualitatively that there is a tendency for the injectors to have different burning configurations. It is believed that the configuration achieved is random, however once the burning configuration is established, it is believed to persist.

Ohara, J.↗

NASA NTRS1978

Wind tunnel tests on a tail-less swept wing span-distributed cargo aircraft configuration

The configuration consisted of a 30 deg -swept, untapered, untwisted wing utilizing a low-moment cambered airfoil of 20 percent streamwise thickness designed for low wave drag at M = 0.6, C sub L = 0.4. The tests covered a range of Mach numbers 0.3 to 0.725 and chord Reynolds number 1,100,000 to 2,040,000, angles of attack up to model buffet and sideslip angles + or - 4 deg. Configuration build up, wing pod filleting, airfoil modification and trailing edge control deflection effects were briefly investigated. Three wing tip vertical tail designs were also tested. Wing body filleting and a simple airfoil modification both produced increments to maximum lift/drag ratio. Addition of pods eliminated pitch instability of the basic wing. While the magnitude of these benefits probably was Reynolds number sensitive, they underline the potential for improving the aerodynamics of the present configuration. The cruise parameter (product of Mach number and lift/drag ratio) attained a maximum close to the airfoil design point. The configuration was found to be positively stable with normal control effectiveness about all three axes in the Mach number and C sub L range of interest.

Rao, D. M.↗

NASA NTRS1979

Low speed wind tunnel test of ground proximity and deck edge effects on a lift cruise fan V/STOL configuration, volume 1

The characteristics were determined of a lift cruise fan V/STOL multi-mission configuration in the near proximity to the edge of a small flat surface representation of a ship deck. Tests were conducted at both static and forward speed test conditions. The model (0.12 scale) tested was a four fan configuration with modifications to represent a three fan configuration. Analysis of data showed that the deck edge effects were in general less critical in terms of differences from free air than a full deck (in ground effect) configuration. The one exception to this was when the aft edge of the deck was located under the center of gravity. This condition, representative of an approach from the rear, showed a significant lift loss. Induced moments were generally small compared to the single axis control power requirements, but will likely add to the pilot work load.

Stewart, V. R.↗

NASA NTRS1980

Complex configuration analysis at transonic speeds

Advanced performance requirements of new combat and transport aircraft together with design time constraints intensify the development and application of three dimensional computational analyses. A computational method which was developed for the specific purpose of providing an engineering analysis of complex aircraft configurations at transonic speeds. Particular attention is given to the recently incorporated wing viscous interaction and canard capabilities. The treatment of fuselage fairings, nacelles, and pylons is reviewed. The means for keeping computing resources at reasonable levels are identified. Three configurations were selected for correlations with experimental data. Taken together, the comparisons illustrate the full extent of current analysis capabilities. The configurations include: (1) a wing fuselage canard fighter; (2) a transport with fuselage fairings, four nacelles, four pylons; and (3) a space vehicle which includes an external fuel tank and rocket boosters (transonic launch configuration).

Boppe, C. W.↗

NASA NTRS1981

SEPAC software configuration control plan and procedures, revision 1

SEPAC Software Configuration Control Plan and Procedures are presented. The objective of the software configuration control is to establish the process for maintaining configuration control of the SEPAC software beginning with the baselining of SEPAC Flight Software Version 1 and encompass the integration and verification tests through Spacelab Level IV Integration. They are designed to provide a simplified but complete configuration control process. The intent is to require a minimum amount of paperwork but provide total traceability of SEPAC software.

Source record↗

NASA NTRS1982

Blockage and flow studies of a generalized test apparatus including various wing configurations in the Langley 7-inch Mach 7 Pilot Tunnel

A 1/12th scale model of the Curved Surface Test Apparatus (CSTA), which will be used to study aerothermal loads and evaluate Thermal Protection Systems (TPS) on a fuselage-type configuration in the Langley 8-Foot High Temperature Structures Tunnel (8 ft HTST), was tested in the Langley 7-Inch Mach 7 Pilot Tunnel. The purpose of the tests was to study the overall flow characteristics and define an envelope for testing the CSTA in the 8 ft HTST. Wings were tested on the scaled CSTA model to select a wing configuration with the most favorable characteristics for conducting TPS evaluations for curved and intersecting surfaces. The results indicate that the CSTA and selected wing configuration can be tested at angles of attack up to 15.5 and 10.5 degrees, respectively. The base pressure for both models was at the expected low level for most test conditions. Results generally indicate that the CSTA and wing configuration will provide a useful test bed for aerothermal pads and thermal structural concept evaluation over a broad range of flow conditions in the 8 ft HTST.

Albertson, C. W.↗

NASA NTRS1979

Application of an optimized winglet configuration to an advanced commercial transport

The design is presented of an aircraft which employs an integrated wing and winglet lift system. Comparison was made with a conventional baseline configuration employing a high-aspect-ratio supercritical wing. An optimized wing-winglet combination was selected from four proposed configurations for which aerodynamic, structural, and weight characteristics were evaluated. Each candidate wing-winglet configuration was constrained to the same induced drag coefficient as the baseline aircraft. The selected wing-winglet configuration was resized for a specific medium-range mission requirement, and operating costs were estimated for a typical mission. Study results indicated that the wing-winglet aircraft was lighter and could complete the specified mission at less cost than the conventional wing aircraft. These indications were sensitive to the impact of flutter characteristics and, to a lesser extent, to the performance of the high-lift system. Further study in these areas is recommended to reduce uncertainty in future development.

Shollenberger, C. A.↗

NASA NTRS1980

Integrated application of active controls (IAAC) technology to an advanced subsonic transport project. Initial ACT configuration design study

The initial ACT configuration design task of the integrated application of active controls (IAAC) technology project within the Energy Efficient Transport Program is summarized. A constrained application of active controls technology (ACT) resulted in significant improvements over a conventional baseline configuration previously established. The configuration uses the same levels of technology, takeoff gross weight, payload, and design requirements/objectives as the baseline, except for flying qualities, flutter, and ACT. The baseline wing is moved forward 1.68 m. The configuration incorporates pitch-augmented stability (which enabled an approximately 10% aft shift in cruise center of gravity and a 45% reduction in horizontal tail size), lateral/directional-augmented stability, an angle of attack limiter, wing load alleviation, and flutter mode control. This resulted in a 930 kg reduction in airplane operating empty weight and a 3.6% improvement in cruise efficiency, yielding a 13% range increase. Adjusted to the 3590 km baseline mission range, this amounts to 6% block fuel reduction and a 15.7% higher incremental return on investment, using 1978 dollars and fuel cost.

Source record↗

NASA NTRS1982

Wind-tunnel investigation of a full-scale canard-configured general aviation aircraft

As part of a broad research program to provide a data base on advanced airplane configurations, a wind-tunnel investigation was conducted in the Langley 30-by 60-Foot Wind Tunnel to determine the aerodynamic characteristics of an advanced canard-configured general aviation airplane. The investigation included measurements of forces and moments of the complete configuration, isolated canard loads, and pressure distributions on the wing, winglet, and canard. Flow visualization was obtained by using surface tufts to determine regions of flow separation and by using a chemical sublimation technique to determine boundary-layer transition locations. Additionally, other tests were conducted to determine simulated rain effects on boundary layer transition. Investigation of configuration effects included variations of canard locations, canard airfoil section, winglet size, and use of a leading-edge droop on the out-board section of the wing.

Yip, L. P.↗

NASA NTRS1974

Low-speed aerodynamic characteristics of a transport configuration having a 42 deg swept supercritical airfoil wing and three tail height positions

A low speed investigation was conducted in the Langley V/STOL tunnel to define the static stability characteristics of an advanced high subsonic speed transport aircraft model in the cruise configuration (no high lift system). The wing of the model had 42 deg sweep of the quarter chord line, an aspect ratio of 6.78, and supercritical airfoil sections. Three different horizontal tail configurations (high, mid, and low) were investigated on the complete model and for the model with the wing removed in order to assess effects of the wing flow field on the tail contributions to both longitudinal and lateral stability characteristics. All the model configurations investigated were tested over an angle of attack range from approximately -5 to 23 deg. Some model configurations were also tested over an angle of attack range from about 11 to 38 deg in order to explore the aerodynamic characteristics in the deep stall region.

Fournier, P. G.↗

NASA NTRS1983

Numerical simulation of the leading-edge separation vortex for a wing and strake-wing configuration

In the present investigation, the 'thin layer' Navier-Stokes equations are used to compute the flow about a delta wing and a strake-delta wing configuration. Both configurations possess blunt noses and rounded leading edges. The computational grid about these configurations is generated using a newly developed three-dimensional grid-generation code which solves a set of Poisson equations with spherical coordinate variables using an alternating direction implicit (ADI) scheme. Computational results are obtained for an isolated wing with 60 deg sweep and a strake-wing configuration with 80-60 deg sweep. Computations for angles of attack in the range from 6 to 30 deg are presented. Attention is given to the effect of the angle of attack, the Mach number, and the Reynolds number. Theoretical results are compared with experimental data.

Fujii, K.↗

NASA NTRS1984

Wind-Tunnel Investigation of an Advanced General Aviation Canard Configuration

Wind-tunnel tests of a model of an advanced canard configuration designed for general aviation were conducted in the Langley 30- by 60-Foot Tunnel. The objective of the tests was to determine the aerodynamic stability and control characteristics of the configuration for a large range of angles of attack and sideslip at several power conditions. Analysis of the aerodynamic data indicates significant effects of power and of center-of-gravity location. For forward center-of-gravity locations, the configuration had extremely stall-resistant stability and control characteristics. For aft center-of-gravity locations and high-power conditions, the combined effects of increased pitch control and reduced longitudinal stability overpowered the stall resistance provided by the canard, which led to a high-angle-of-attack, deep-stall trim condition. Other aspects of the aerodynamic characteristics studied include the following: flow-visualization study, effect of negative angles of attack, lateral-directional characteristics, and comparison of the stall characteristics with another canard configuration.

Chambers, J. R.↗

NASA NTRS1984

The computation of mesh configurations for three-dimensional flow analysis

A geometry modeling method was developed to define three-dimensional mesh configurations, which were expressed by the set of surface intersections with a coordinate mesh. These configurations define bodies for transonic potential-flow computation in simple physical coordinates. Various configurations were prepared for 3-D potential flow analysis, including many bare inlet models in cylindrical coordinates. Trimmed surface models were used to prepare nacelle installation configurations. A variety of ducts and mixers were represented. Analytically defined mesh/surface intersections were compared with similar data obtained from the corresponding surface model. Parameters for an analytic surface definition from mesh-surface intersections obtained from a model of the surface were produced. In both studies the modeling accuracy was shown to be compatible with the flow analysis requirements. This technique fulfills the requirements of the associated three-dimensional potential-flow analysis. It preserves the flow analysis method's superior flexibility for adapting to unusual geometries. The geometry modeling technique is supported by a sufficient set of tools for effective use by general users, and sufficient accuracy was demonstrated.

Gibson, S. G.↗

NASA NTRS1984

Software control and system configuration management: A systems-wide approach

A comprehensive software control and system configuration management process for flight-crucial digital control systems of advanced aircraft has been developed and refined to insure efficient flight system development and safe flight operations. Because of the highly complex interactions among the hardware, software, and system elements of state-of-the-art digital flight control system designs, a systems-wide approach to configuration control and management has been used. Specific procedures are implemented to govern discrepancy reporting and reconciliation, software and hardware change control, systems verification and validation testing, and formal documentation requirements. An active and knowledgeable configuration control board reviews and approves all flight system configuration modifications and revalidation tests. This flexible process has proved effective during the development and flight testing of several research aircraft and remotely piloted research vehicles with digital flight control systems that ranged from relatively simple to highly complex, integrated mechanizations.

Petersen, K. L.↗

NASA NTRS1983

Software control and system configuration management - A process that works

Petersen, K. L.↗

NASA NTRS1985

Detailed pressure distribution measurements obtained on several configurations of an aspect-ratio-7 variable twist wing

Detailed pressure distribution measurements were made for 11 twist configurations of a unique, multisegmented wing model having an aspect ratio of 7 and a taper ratio of 1. These configurations encompassed span loads ranging from that of an untwisted wing to simple flapped wings both with and without upper-surface spoilers attached. For each of the wing twist configurations, electronic scanning pressure transducers were used to obtain 580 surface pressure measurements over the wing in about 0.1 sec. Integrated pressure distribution measurements compared favorably with force-balance measurements of lift on the model when the model centerbody lift was included. Complete plots and tabulations of the pressure distribution data for each wing twist configuration are provided.

Holbrook, G. T.↗

NASA NTRS1985

Attitude Control Tradeoff Study Between the Use of a Flexible Beam and a Tether Configuration for the Connection of Two Bodies in Orbit

Sometimes it is necessary to mount a payload remotely from the main body of a spacecraft or space station. The reasons for this vary from vibration isolation to avoidance of measurement contamination. For example the SP-100 project, which grew out of the increased interest in nuclear power in space for space stations and for deep space explorations, requires separation of the nuclear reactor from the user because of vibration, heat and radiation. The different attitude control problems for beam and tether configurations are discussed. The beam configuration uses a conservative design approach. The vibration, beam flexibility and deployment concerns are analyzed. The tether configuration offers some very attractive design features, but not without several thorny problems. These problems are analyzed. One configuration will be recommended for the main thrust of the SP-100 design effort based on attitude control considerations.

Graff, S. H.↗