Results for “Computational Fluid Dynamics Conduction” — Page 15

NASA NTRS1999

An Inviscid Computational Study of an X-33 Configuration at Hypersonic Speeds

This report documents the results of a study conducted to compute the inviscid longitudinal aerodynamic characteristics of a simplified X-33 configuration. The major components of the X-33 vehicle, namely the body, the canted fin, the vertical fin, and the body-flap, were simulated in the CFD (Computational Fluid Dynamic) model. The rear-ward facing surfaces at the base including the aerospike engine surfaces were not simulated. The FELISA software package consisting of an unstructured surface and volume grid generator and two inviscid flow solvers was used for this study. Computations were made for Mach 4.96, 6.0, and 10.0 with perfect gas air option, and for Mach 10 with equilibrium air option with flow condition of a typical point on the X-33 flight trajectory. Computations were also made with CF4 gas option at Mach 6.0 to simulate the CF4 tunnel flow condition. An angle of attack range of 12 to 48 deg was covered. The CFD results were compared with available wind tunnel data. Comparison was good at low angles of attack; at higher angles of attack (beyond 25 deg) some differences were found in the pitching moment. These differences progressively increased with increase in angle of attack, and are attributed to the viscous effects. However, the computed results showed the trends exhibited by the wind tunnel data.

Prabhu, Ramadas K.↗

NASA NTRS1992

NASP and SDI Spearhead CFD Developments

The National Aerospace Plane (NASP) program's purpose, as stated by the National Space Council, is to "develop and demonstrate hypersonic technologies with the ultimate goal of single stage to orbit." The council has also directed that "performance of the experimental flight vehicle will be constrained to the minimum necessary to meet the highest priority research, as opposed to operational objectives .... The program will be conducted in such a way as to minimize technical and cost uncertainty associated with the experimental vehicle." The purpose of the Strategic Defense Initiative (SDI), as defined by President Bush, is "...protection from limited ballistic missile strikes, whatever their source." Computational fluid dynamics (CFD) plays a vital role in both endeavors.

Mehta, Unmeel B.↗

NASA NTRS1990

The development and evaluation of numerical algorithms for MIMD computers

Two activities were pursued under this grant. The first was a visitor program to conduct research on numerical algorithms for MIMD computers. The program is summarized in the following attachments. Attachment A - List of Researchers Supported; Attachment B - List of Reports Completed; and Attachment C - Reports. The second activity was a workshop on the Control of fluid Dynamic Systems held on March 28 to 29, 1989. The workshop is summarized in attachments. Attachment D - Workshop Summary; and Attachment E - List of Workshop Participants.

Voigt, Robert G.↗

NASA NTRS1993

Computational analysis of Variable Thrust Engine (VTE) performance

The Variable Thrust Engine (VTE) of the Orbital Maneuvering Vehicle (OMV) uses a hypergolic propellant combination of Monomethyl Hydrazine (MMH) and Nitrogen Tetroxide (NTO) as fuel and oxidizer, respectively. The performance of the VTE depends on a number of complex interacting phenomena such as atomization, spray dynamics, vaporization, turbulent mixing, convective/radiative heat transfer, and hypergolic combustion. This study involved the development of a comprehensive numerical methodology to facilitate detailed analysis of the VTE. An existing Computational Fluid Dynamics (CFD) code was extensively modified to include the following models: a two-liquid, two-phase Eulerian-Lagrangian spray model; a chemical equilibrium model; and a discrete ordinate radiation heat transfer model. The modified code was used to conduct a series of simulations to assess the effects of various physical phenomena and boundary conditions on the VTE performance. The details of the models and the results of the simulations are presented.

Giridharan, M. G.↗

NASA NTRS2013

Long Penetration Mode Counterflowing Jets for Supersonic Slender Configurations - A Numerical Study

A novel approach of using counterflowing jets positioned strategically on the aircraft and exploiting its long penetration mode (LPM) of interaction towards sonic-boom mitigation forms the motivation for this study. Given that most previous studies on the counterflowing LPM jet have all been on blunt bodies and at high supersonic or hypersonic flow conditions, exploring the feasibility to obtain a LPM jet issuing from a slender body against low supersonic freestream conditions is the main focus of this study. Computational fluid dynamics computations of axisymmetric models (cone-cylinder and quartic geometry), of relevance to NASA's High Speed project, are carried out using the space-time conservation element solution element viscous flow solver with unstructured meshes. A systematic parametric study is conducted to determine the optimum combination of counterflowing jet size, mass flow rate, and nozzle geometry for obtaining LPM jets. Details from these computations will be used to assess the potential of the LPM counterflowing supersonic jet as a means of active flow control for enabling supersonic flight over land and to establish the knowledge base for possible future implementation of such technologies.

Venkatachari, Balaji Shankar↗

NASA NTRS2023

CFD Modeling of Bi-Directional PMD inside Cryogenic Propellant Tanks Onboard Parabolic Flights

Future cryogenic propulsion systems will require efficient methods with which to transfer cryogenic propellants from a depot storage tank to a customer receiver tank to minimize cost and maximize reusability. The Reduced Gravity Cryogenic Transfer project is currently developing advanced cryogenic fluid management technology and developing and validating new numerical models for three phases of transfer: line chilldown, tank chilldown, and tank fill. Additionally, multiple liquid nitrogen (LN 2 ) parabolic flight transfer rigs are being designed by universities and NASA to investigate the gravitational sensitivities that exist in these three technologies. In order to maximize the collection of low-g data during flights, it is required to extract as much (LN 2 as possible from the supply tank, despite variable gravity levels. The purpose of this paper is to present computational fluid dynamics (CFD) volume of fluid simulations of (LN 2 behavior in the supply tank onboard parabolic flights to validate the optimal design of a bi-directional propellant management device (PMD) using the commercial software FLOW-3D. A parametric study is conducted on the effects of gravity level, fill level, pore size, open area, thickness, and type of baffle on PMD performance. Based on results, the PMD as designed exceeds the targeted expulsion efficiency.

Jason Hartwig↗

NASA NTRS1999

Aeroservoelastic and Flight Dynamics Analysis Using Computational Fluid Dynamics

This document in large part is based on the Masters Thesis of Cole Stephens. The document encompasses a variety of technical and practical issues involved when using the STARS codes for Aeroservoelastic analysis of vehicles. The document covers in great detail a number of technical issues and step-by-step details involved in the simulation of a system where aerodynamics, structures and controls are tightly coupled. Comparisons are made to a benchmark experimental program conducted at NASA Langley. One of the significant advantages of the methodology detailed is that as a result of the technique used to accelerate the CFD-based simulation, a systems model is produced which is very useful for developing the control law strategy, and subsequent high-speed simulations.

Arena, Andrew S., Jr.↗

NASA NTRS1992

Postflight aerothermodynamic analysis of Pegasus(tm) using computational fluid dynamic techniques

The objective was to validate the computational capability of the NASA Ames Navier-Stokes code, F3D, for flows at high Mach numbers using comparison flight test data from the Pegasus (tm) air launched, winged space booster. Comparisons were made with temperature and heat fluxes estimated from measurements on the wing surfaces and wing-fuselage fairings. Tests were conducted for solution convergence, sensitivity to grid density, and effects of distributing grid points to provide high density near temperature and heat flux sensors. The measured temperatures were from sensors embedded in the ablating thermal protection system. Surface heat fluxes were from plugs fabricated of highly insulative, nonablating material, and mounted level with the surface of the surrounding ablative material. As a preflight design tool, the F3D code produces accurate predictions of heat transfer and other aerodynamic properties, and it can provide detailed data for assessment of boundary layer separation, shock waves, and vortex formation. As a postflight analysis tool, the code provides a way to clarify and interpret the measured results.

Kuhn, Gary D.↗

NASA NTRS2010

Slot Nozzle Effects for Reduced Sonic Boom on a Generic Supersonic Wing Section

NASA has conducted research programs to reduce or eliminate the operational restrictions of supersonic aircraft over populated areas. Restrictions are due to the disturbance from the sonic boom, caused by the coalescence of shock waves formed off the aircraft. Results from two-dimensional computational fluid dynamic (CFD) analyses (performed on a baseline Mach 2.0 nozzle in a simulated Mach 2.2 flow) indicate that over-expanded and under-expanded operation of the nozzle has an effect on the N-wave boom signature. Analyses demonstrate the feasibility of reducing the magnitude of the sonic boom N-wave by controlling the nozzle plume interaction with the nozzle boat tail shock structure. This work was extended to study the impact of integrating a high aspect ratio exhaust nozzle or long slot nozzle on the trailing edge of a supersonic wing. The nozzle is operated in a highly under-expanded condition, creating a large exhaust plume and a shock at the trailing edge of the wing. This shock interacts with and suppresses the expansion wave caused by the wing, a major contributor to the sonic boom signature. The goal was to reduce the near field pressures caused by the expansion using a slot nozzle located at the wing trailing edge. Results from CFD analysis on a simulated wing cross-section and a slot nozzle indicate potential reductions in sonic boom signature compared to a baseline wing with no propulsion or trailing edge exhaust. Future studies could investigate if this effect could be useful on a supersonic aircraft for main propulsion, auxiliary propulsion, or flow control.

Castner, Raymond S.↗

NASA NTRS2010

Slot Nozzle Effects for Reduced Sonic Boom on a Generic Supersonic Wing Section

NASA has conducted research programs to reduce or eliminate the operational restrictions of supersonic aircraft over populated areas. Restrictions are due to the disturbance from the sonic boom, caused by the coalescence of shock waves formed off the aircraft. Results from two-dimensional computational fluid dynamic (CFD) analyses (performed on a baseline Mach 2.0 nozzle in a simulated Mach 2.2 flow) indicate that over-expanded and under-expanded operation of the nozzle has an effect on the N-wave boom signature. Analyses demonstrate the feasibility of reducing the magnitude of the sonic boom N-wave by controlling the nozzle plume interaction with the nozzle boat tail shock structure. This work was extended to study the impact of integrating a high aspect ratio exhaust nozzle or long slot nozzle on the trailing edge of a supersonic wing. The nozzle is operated in a highly under-expanded condition, creating a large exhaust plume and a shock at the trailing edge of the wing. This shock interacts with and suppresses the expansion wave caused by the wing, a major contributor to the sonic boom signature. The goal was to reduce the near field pressures caused by the expansion using a slot nozzle located at the wing trailing edge. Results from CFD analysis on a simulated wing cross-section and a slot nozzle indicate potential reductions in sonic boom signature compared to a baseline wing with no propulsion or trailing edge exhaust. Future studies could investigate if this effect could be useful on a supersonic aircraft for main propulsion, auxiliary propulsion, or flow control.

Caster, Raymond S.↗

NASA NTRS2013

Aerodynamic Reconstruction Applied to Parachute Test Vehicle Flight Data Analysis

The aerodynamics, both static and dynamic, of a test vehicle are critical to determining the performance of the parachute cluster in a drop test and for conducting a successful test. The Capsule Parachute Assembly System (CPAS) project is conducting tests of NASA's Orion Multi-Purpose Crew Vehicle (MPCV) parachutes at the Army Yuma Proving Ground utilizing the Parachute Test Vehicle (PTV). The PTV shape is based on the MPCV, but the height has been reduced in order to fit within the C-17 aircraft for extraction. Therefore, the aerodynamics of the PTV are similar, but not the same as, the MPCV. A small series of wind tunnel tests and computational fluid dynamics cases were run to modify the MPCV aerodynamic database for the PTV, but aerodynamic reconstruction of the flights has proven an effective source for further improvements to the database. The acceleration and rotational rates measured during free flight, before parachute inflation but during deployment, were used to con rm vehicle static aerodynamics. A multibody simulation is utilized to reconstruct the parachute portions of the flight. Aerodynamic or parachute parameters are adjusted in the simulation until the prediction reasonably matches the flight trajectory. Knowledge of the static aerodynamics is critical in the CPAS project because the parachute riser load measurements are scaled based on forebody drag. PTV dynamic damping is critical because the vehicle has no reaction control system to maintain attitude - the vehicle dynamics must be understood and modeled correctly before flight. It will be shown here that aerodynamic reconstruction has successfully contributed to the CPAS project.

Cassady, Leonard D.↗

NASA NTRS1996

Experimental Investigation of Crossing Shock Wave-Turbulent Boundary Layer-Bleed Interaction

Results of an experimental investigation of a symmetric crossing shock wave/turbulent boundary layer/bleed interaction are presented for a freestream unit Reynolds number of 1.68 x 10(exp 7)/m, a Mach number of 2.81, and deflection angles of 8 degrees. The data obtained in this study are bleed mass flow rate using a trace gas technique, qualitative information in the form of oil flow visualization, flow field Pitot pressures, and static pressure measurements using pressure sensitive paint. The main objective of this test is two-fold. First, this study is conducted to explore boundary layer control through mass flow removal near a large region of separated flow caused by the interaction of a double fin-induced shock wave and an incoming turbulent boundary layer. Also, a comprehensive data set is needed for computational fluid dynamics code validation.

Kim, Hyun↗

NASA NTRS2016

NASA ERA Integrated CFD for Wind Tunnel Testing of Hybrid Wing-Body Configuration

NASAs Environmentally Responsible Aviation (ERA) Project explores enabling technologies to reduce aviations impact on the environment. One research challenge area for the project has been to study advanced airframe and engine integration concepts to reduce community noise and fuel burn. In order to achieve this, complex wind tunnel experiments at both the NASA Langley Research Centers (LaRC) 14x22 and the Ames Research Centers 40x80 low-speed wind tunnel facilities were conducted on a Boeing Hybrid Wing Body (HWB) configuration. These wind tunnel tests entailed various entries to evaluate the propulsion airframe interference effects including aerodynamic performance and aeroacoustics. In order to assist these tests in producing high quality data with minimal hardware interference, extensive Computational Fluid Dynamic (CFD) simulations were performed for everything from sting design and placement for both the wing body and powered ejector nacelle systems to the placement of aeroacoustic arrays to minimize its impact on the vehicles aerodynamics. This paper will provide a high level summary of the CFD simulations that NASA performed in support of the model integration hardware design as well as some simulation guideline development based on post-test aerodynamic data. In addition, the paper includes details on how multiple CFD codes (OVERFLOW, STAR-CCM+, USM3D, and FUN3D) were efficiently used to provide timely insight into the wind tunnel experimental setup and execution.

Computational Fluid Dynamics↗

NASA NTRS2000

Advanced Methods for Aircraft Engine Thrust and Noise Benefits: Nozzle-Inlet Flow Analysis

In this project, we continue to develop the previous joint research between the Fluid Mechanics and Acoustics Laboratory (FM&AL) at Hampton University (HU) and the Jet Noise Team (JNT) at the NASA Langley Research Center (NASA LaRC). The FM&AL was established at Hampton University in June of 1996 and has conducted research under two NASA grants: NAG-1-1835 (1996-99), and NAG-1-1936 (1997-00). In addition, the FM&AL has jointly conducted research with the Central AeroHydrodynamics Institute (TsAGI, Moscow) in Russia under a Civilian Research and Development Foundation (CRDF) grant #RE2-136 (1996-99). The goals of the FM&AL programs are twofold: (1) to improve the working efficiency of the FM&AUs team in generating new innovative ideas and in conducting research in the field of fluid dynamics and acoustics, basically for improvement of supersonic and subsonic aircraft engines, and (2) to attract promising minority students to this research and training and, in cooperation with other HU departments, to teach them basic knowledge in Aerodynamics, Gas Dynamics, and Theoretical and Experimental Methods in Aeroacoustics and Computational Fluid Dynamics (CFD). The research at the HU FM&AL supports reduction schemes associated with the emission of engine pollutants for commercial aircraft and concepts for reduction of observables for military aircraft. These research endeavors relate to the goals of the NASA Strategic Enterprise in Aeronautics concerning the development of environmentally acceptable aircraft. It is in this precise area, where the US aircraft industry, academia, and Government are in great need of trained professionals and which is a high priority goal of the Minority University Research and Education (MUREP) Program, that the HU FM&AL can make its most important contribution. The main achievements for the reporting period in the development of concepts for noise reduction and improvement in efficiency for jet exhaust nozzles and inlets for aircraft engines are as follows: (1) Publications- The AIAA Paper #99-1924 has been presented at the 5th AIAA/CEAS Aeroacoustics Conference, May 10-12, 1999, Seattle, WA; the AIAA Paper #00-3315 has been accepted for the 36th AIAA/ASME/ SAE/ASEE Joint Propulsion Conference, 17-19 July, 2000, Huntsville, AL; and another paper has been accepted for the International Environmental Congress, 14-16 June, 2000, St.-Petersburg, Russia. (2) Two patents were granted on July 20, 1999, and January 12, 2000. (3) Three reports/presentations at the NASA LaRC and GRC (06/22199, 09/26/ 99, and 06/25/00). (4) Grants and Proposals: Four proposals were submitted to the NASA and CRDF; a NASA Faculty Award was granted on January, 2000. A CRDF Young Investigator Program Award was granted for a 3 months visit of the Russian scientist to the HU FM&AL (03/99-05/99). (5) Theory and Numerical Simulations- Analytical theory, numerical simulation, comparison of theoretical with experimental results, and modification of theoretical approaches, models, grids etc. have been conducted for several complicated 2D and 3D nozzle and inlet designs using NASA codes based on full Euler and Navier-Stokes solvers: CFL3D, CRAFT, GODUNOV, and others. New approach for environmental monitoring via infrasound. (6) Experimental Tests: Experimental acoustic tests at the TsAGI, Moscow, with nozzles having Screwdriver or Axisymmetric Plug and Permeable Shells. A small scale working model of the NASA Low Speed Wind Tunnel (LSWT) has been installed in the Experimental Hall of the HU FM&AL (June, 1999). Preliminary preparations for experimental tests were made. (7) Students Research Activity: Involvement of the two graduate students as research assistants in the current research project.

Gilinsky, Mikhail↗

NASA NTRSDate not supplied

Automated Unstructured Grid Adaptation on a Strut Fuel Injector at Hypervelocity Flow Conditions

Computational fluid dynamics (CFD) analysis is presented with the use of an automated unstructured grid adaptation tool on a strut fuel injector at hypervelocity flow conditions. The analysis was carried out with the VULCAN-CFD solver using Reynolds-averaged simulations (RAS). The hypervelocity flow conditions match the high Mach number flow of the experiments conducted as part of the Enhanced Injection and Mixing Project (EIMP) at the NASA Langley Research Center (LaRC). The current work uses an automated grid adaptation tool recently implemented in VULCAN-CFD, and explores this tool’s ability to solve highspeed mixing problems. Simulation results obtained using the unstructured adaptive grid approach are compared to those on a user-generated structured grid. These results are evaluated by analyzing how efficiently comparable fidelity results are obtained from both adapted and structured simulations. In addition, two adaptation strategies were used to explore the impact on the final solution. In the current work, the unstructured grid adaptation tool automatically generates unstructured grids and performs adaptation of the grid based on a Hessian error estimate of a specified flowfield parameter. Multiple adaptations were executed using each run strategy with the one-dimensional values of the mixing efficiency used to determine grid convergence and for comparison with the structured grid simulation results. It was found that the unstructured adaptive grid simulations were able to produce results that matched closely with those on structured grids using far fewer grid cells, and thus, requiring far less computational time to reach the solution. It was also discovered that the adaptation run strategy influenced the total number of grid cells and the efficiency with which a final grid-adapted solution was reached. Furthermore, motivated by the grid convergence index (GCI) used for structured grid simulations, a grid convergence estimate (GCE) was developed and demonstrated for the grid adaptation. Overall, the investigation demonstrated that the automated unstructured grid adaptation tool implemented in VULCAN-CFD is capable of accurately and efficiently solving complex high-speed mixing problems with only a fraction of the grid cells required to obtain comparable results on a user-generated structured grid.

hypersonics↗

NASA NTRSDate not supplied

Automated Unstructured Grid Adaptation on a Strut Fuel Injector at Hypervelocity Flow Conditions

Computational fluid dynamics (CFD) analysis is presented with the use of an automated unstructured grid adaptation tool on a strut fuel injector at hypervelocity flow conditions. The analysis was carried out with the VULCAN-CFD solver using Reynolds-averaged simulations (RAS). The hypervelocity flow conditions match the high Mach number flow of the experiments conducted as part of the Enhanced Injection and Mixing Project (EIMP) at the NASA Langley Research Center (LaRC). The current work uses an automated grid adaptation tool recently implemented in VULCAN-CFD, and explores this tool’s ability to solve highspeed mixing problems. Simulation results obtained using the unstructured adaptive grid approach are compared to those on a user-generated structured grid. These results are evaluated by analyzing how efficiently comparable fidelity results are obtained from both adapted and structured simulations. In addition, two adaptation strategies were used to explore the impact on the final solution. In the current work, the unstructured grid adaptation tool automatically generates unstructured grids and performs adaptation of the grid based on a Hessian error estimate of a specified flowfield parameter. Multiple adaptations were executed using each run strategy with the one-dimensional values of the mixing efficiency used to determine grid convergence and for comparison with the structured grid simulation results. It was found that the unstructured adaptive grid simulations were able to produce results that matched closely with those on structured grids using far fewer grid cells, and thus, requiring far less computational time to reach the solution. It was also discovered that the adaptation run strategy influenced the total number of grid cells and the efficiency with which a final grid-adapted solution was reached. Furthermore, motivated by the grid convergence index (GCI) used for structured grid simulations, a grid convergence estimate (GCE) was developed and demonstrated for the grid adaptation. Overall, the investigation demonstrated that the automated unstructured grid adaptation tool implemented in VULCAN-CFD is capable of accurately and efficiently solving complex high-speed mixing problems with only a fraction of the grid cells required to obtain comparable results on a user-generated structured grid.

hypersonics↗

NASA NTRSDate not supplied

Automated Unstructured Grid Adaptation on a Strut Fuel Injector at Hypervelocity Flow Conditions

Computational fluid dynamics (CFD) analysis is presented with the use of an automated unstructured grid adaptation tool on a strut fuel injector at hypervelocity flow conditions. The analysis was carried out with the VULCAN-CFD solver using Reynolds-averaged simulations (RAS). The hypervelocity flow conditions match the high Mach number flow of the experiments conducted as part of the Enhanced Injection and Mixing Project (EIMP) at the NASA Langley Research Center (LaRC). The current work utilizes an automated grid adaptation tool recently implemented into VULCAN-CFD, and explores this tool’s ability to solve high-speed mixing problems. Simulation results obtained using the unstructured adaptive grid approach are compared to those on a user generated structured grid. These results are evaluated by analyzing how efficiently comparable fidelity results are obtained from both adapted and structured simulations. In addition, two adaptation strategies were used to explore the impact on the final solution. In the current work, the unstructured grid adaptation tool automatically generates unstructured grids and performs adaptation of the grid based on a Hessian error estimate of a specified flow field parameter. Multiple adaptations were executed using each run strategy with the one-dimensional values of the mixing efficiency used to determine grid convergence and for comparison with the structured grid simulation results. It was found that the unstructured adaptive grid simulations were able to produce results that matched closely with those on structured grids using far fewer grid cells, and thus, requiring far less computational time to reach the solution. It was also discovered that the adaptation run strategy influenced the total number of grid cells and the efficiency with which a final grid-adapted solution was reached. Overall, the investigation demonstrated that the automated unstructured grid adaptation tool implemented in VULCAN-CFD is capable of accurately and efficiently solving complex highspeed mixing problems using only a fraction of the grid cells required to obtain comparable results using a user-generated structured grid.

grid adaptation↗

NASA NTRS1987

Study of non-equilibrium transport phenomena

Nonequilibrium phenomena due to real gas effects are very important features of low density hypersonic flows. The shock shape and emitted nonequilibrium radiation are identified as the bulk flow behavior parameters which are very sensitive to the nonequilibrium phenomena. These parameters can be measured in shock tubes, shock tunnels, and ballistic ranges and used to test the accuracy of computational fluid dynamic (CFD) codes. Since the CDF codes, by necessity, are based on multi-temperature models, it is also desirable to measure various temperatures, most importantly, the vibrational temperature. The CFD codes would require high temperature rate constants, which are not available at present. Experiments conducted at the NASA Electric Arc-driven Shock Tube (EAST) facility reveal that radiation from steel contaminants overwhelm the radiation from the test gas. For the measurement of radiation and the chemical parameters, further investigation and then appropriate modifications of the EAST facility are required.

Sharma, Surendra P.↗