Results for “Commercial Building” — Page 15

NASA NTRS1998

The Successful Transfer of Space Derived Convergent Spray: An Application for Industrial Roof Coatings and Interstate Bridge Repair

A partnership was formed between the National Aeronautics and Space Administration (NASA), the Environmental Protection Agency (EPA), and United Technologies USBI Company to develop, demonstrate, and evaluate a technology that uses a solventless spray process for depositing a lightweight, highly filled roof coating on low-sloped commercial roofs. Although the levels of volatile organic compound (VOC) emissions from industrial roof coating's and paint operations have been reduced in recent years, this partnership,was an effort to further reduce VOC emission levels and to also demonstrate the use of reclaimed automobile tire rubber as a filler material in roof coating systems. Different materials and coatings were evaluated and tested before the final selection used to coat the roofs of two small buildings at NASA's Marshall Space Flight Center during fiscal year 1997. The project successfully leveraged the investment of EPA, NASA and private sector resources to demonstrate a pre-commercial roofing coating process. This process utilizes the Convergent Spray Technologies process, which was initially developed by USBI to apply highly-filled, thermal protection coatings to the Space Shuttle Solid Rocket Boosters. A second partnership between the NASA, Federal Highway Administration, Alabama Department of Transportation and USBI Company was formed to develop and demonstrate the Convergent Spray Technology as a method of applying a skid resistant coating to interstate roads and concrete bridge decking's. Again, different materials and coatings were evaluated and tested before the final selection of ground flint and resin. Two field demonstrations were performed during fiscal year 1997 for the purpose of evaluating the coating system under actual highway conditions. These coatings were applied on Interstate 65 near Huntsville Alabama, and in the Mobile Bankhead tunnel. The system performed this task without the use of harmful solvents, and accomplished the process in a single application. This project successfully leveraged the investment of NASA, Federal Highway Administration, the Alabama Department of Transportation, and private sector funding.

McMillan, Vernotto C.↗

NASA NTRSDate not supplied

NASA’s Interest in 3GPP Mobile Telecommunications Protocols for Near Earth Space and the Lunar Surface

In the next several years, NASA intends to return astronauts to the Moon through the Artemis Program. Under Artemis, NASA plans to collaborate with commercial and international partners to establish a long-term presence on the Moon. Near-term Artemis missions will be analogous but much more sophisticated versions of the last couple of Apollo missions. For example, the first area expected to be explored by an Artemis mission is near the south pole as opposed to the mid-latitudes visited by the Apollo astronauts, which makes direct communications with Earth more complicated. Lunar infrastructure will eventually be built over time by many organizations, public and private, to support sustained human exploration, science, and industrial activities on the Moon. A robust lunar communications and navigation infrastructure will be essential to realizing this long-term vision. Meanwhile, on Earth, major advances are being made as5G mobile telecommunications rollout across the globe. Furthermore, the 3rdGeneration Partnership Project (3GPP) is beginning to define future 6G capabilities. NASA envisions a lunar communications and navigation network with capabilities similar to those of communication networks we enjoy here on Earth. Building such a network will require participation by many organizations. NASA’s Tipping Point program seeks industry-developed space technologies that can both foster commercial space capabilities and benefit future NASA missions. This paper provides an overview of NASA’s interest in 3GPPanddescribescurrent work based on 3GPP standards within NASA or funded by NASA, such as Nokia’s upcoming Tipping Point demonstration of 4G/LTE on the lunar surface in early 2023.

Bernard L Edwards↗

NASA NTRS1975

Building a computer-aided design capability using a standard time share operating system

The paper describes how an integrated system of engineering computer programs can be built using a standard commercially available operating system. The discussion opens with an outline of the auxiliary functions that an operating system can perform for a team of engineers involved in a large and complex task. An example of a specific integrated system is provided to explain how the standard operating system features can be used to organize the programs into a simple and inexpensive but effective system. Applications to an aircraft structural design study are discussed to illustrate the use of an integrated system as a flexible and efficient engineering tool. The discussion concludes with an engineer's assessment of an operating system's capabilities and desirable improvements.

Sobieszczanski, J.↗

NASA NTRS2017

Quantum Computation: Entangling with the Future

Commercial applications of quantum computation have become viable due to the rapid progress of the field in the recent years. Efficient quantum algorithms are discovered to cope with the most challenging real-world problems that are too hard for classical computers. Manufactured quantum hardware has reached unprecedented precision and controllability, enabling fault-tolerant quantum computation. Here, I give a brief introduction on what principles in quantum mechanics promise its unparalleled computational power. I will discuss several important quantum algorithms that achieve exponential or polynomial speedup over any classical algorithm. Building a quantum computer is a daunting task, and I will talk about the criteria and various implementations of quantum computers. I conclude the talk with near-future commercial applications of a quantum computer.

Jiang, Zhang↗

NASA NTRS1978

Utilization requirements. A southern California Gas Company project SAGE report: Utilization requirements

Utilization requirements are given and comparisons made of two phase III SAGE (solar assisted gas energy) installations in California: (1) a retrofit installation in an existing apartment building in El Toro, and (2) an installation in a new apartment building in Upland. Such testing in the field revealed the requirements to be met if SAGE-type installations are to become commercially practical on a widespread basis in electric and gas energy usage.

Barbieri, R. H.↗

NASA NTRS1998

Computational Modeling of Semiconductor Dynamics at Femtosecond Time Scales

The Interchange No. NCC2-5149 deals with the emerging technology of photonic (or optoelectronic) integrated circuits (PICs or OEICs). In PICs, optical and electronic components are grown together on the same chip. To build such devices and subsystems, one needs to model the entire chip. PICs are useful for building components for integrated optical transmitters, integrated optical receivers, optical data storage systems, optical interconnects, and optical computers. For example, the current commercial rate for optical data transmission is 2.5 gigabits per second, whereas the use of shorter pulses to improve optical transmission rates would yield an increase of 400 to 1000 times. The improved optical data transmitters would be used in telecommunications networks and computer local-area networks. Also, these components can be applied to activities in space, such as satellite to satellite communications, when the data transmissions are made at optical frequencies. The research project consisted of developing accurate computer modeling of electromagnetic wave propagation in semiconductors. Such modeling is necessary for the successful development of PICs. More specifically, these computer codes would enable the modeling of such devices, including their subsystems, such as semiconductor lasers and semiconductor amplifiers in which there is femtosecond pulse propagation. Presently, there are no computer codes that could provide this modeling. Current codes do not solve the full vector, nonlinear, Maxwell's equations, which are required for these short pulses and also current codes do not solve the semiconductor Bloch equations, which are required to accurately describe the material's interaction with femtosecond pulses. The research performed under NCC2-5149 solves the combined Maxwell's and Bloch's equations.

Agrawal, Govind P.↗

NASA NTRS2010

Adaptation of the Camera Link Interface for Flight-Instrument Applications

COTS (commercial-off-the-shelf) hard ware using an industry-standard Camera Link interface is proposed to accomplish the task of designing, building, assembling, and testing electronics for an airborne spectrometer that would be low-cost, but sustain the required data speed and volume. The focal plane electronics were designed to support that hardware standard. Analysis was done to determine how these COTS electronics could be interfaced with space-qualified camera electronics. Interfaces available for spaceflight application do not support the industry standard Camera Link interface, but with careful design, COTS EGSE (electronics ground support equipment), including camera interfaces and camera simulators, can still be used.

Randall, David P.↗

NASA NTRS2014

Fall 2014 Marketing Internship Final Report

The function of Kennedy Space Center's Center Planning and Development (CPD) directorate is to develop partnerships with the commercial space industry, academia, and other non-NASA government agencies to use KSC's facilities, technical capabilities, technologies and expertise, while building on existing partnerships. As an intern for the Spaceport Planning Office within the CPD, I played an essential part in promoting these opportunities by assisting the Marketing Specialist with organizing CPD's multi-booth exhibit for KSC's 2014 Innovation Expo. I was also responsible for gathering/reviewing video clips of interviews from existing partners to be used as potential footage for video testimonials that would be used to educate the public on KSC. My last project was to develop a standard presentation highlighting the benefits and potential of partnering with KSC, which would be used by KSC partnership development managers (PDMs) when presenting externally to potential partners. With these various projects and limited timeframe to complete each, learning to effectively manage my time and actively multitask was imperative.

Marketing↗

NASA NTRSDate not supplied

NASA’S Current Efforts and Applications of NDE to Improve Space Flight Safety

National Aeronautics and Space Administration (NASA) continues to push the boundary of manned flight. Current mission profiles include flights to the moon and mars. Many of these missions require advance manufacturing and planned off planet resource utilization. As NASA continues to develop highly advance materials and manufacturing techniques to meet these mission profiles, inspection of these increasingly complex parts has had to evolve as well. Additive manufacturing is coming to the forefront as a primary manufacturing technique but offers unique challenges when inspection and certification are required. NASA has been working diligently to be a leader in developing and utilizing inspection techniques capable of inspecting these highly advanced parts. Additionally additive manufacturing techniques can also be used to build parts in space and provides a vehicle for in-situ resource utilization for off world missions. As NASA and its commercial crew partners move forward inspection techniques will need to continue to advance to ensure safe manned space flight. In this talk NASA will highlight many of the advanced nondestructive evaluation efforts going on across the agency. As well as highlights for points of infusion for helping NASA meet it’s future missions.

NDE↗

NASA NTRSDate not supplied

NASA's Office Safety Mission Assurance Efforts to Improve Non-destructive Evaluation Methods for Additive Manufacturing and In-Space Inspection

National Aeronautics and Space Administration (NASA) continues to push the boundary of manned flight. Current mission profiles include flights to the Moon and Mars. Many of these missions require advance manufacturing and planned off planet resource utilization. As NASA continues to develop highly advance materials and manufacturing techniques to meet these mission profiles, inspection of these increasingly complex parts has had to evolve as well. Additive manufacturing is coming to the forefront as a primary manufacturing technique but offers unique challenges when inspection and certification are required. NASA has been working diligently to be a leader in developing and utilizing inspection techniques capable of inspecting these highly advanced parts. Additionally additive manufacturing techniques can also be used to build parts in space and provides a vehicle for in-situ resource utilization for off world missions. As NASA and its commercial crew partners move forward, inspection techniques will need to continue to advance to ensure safe manned space flight. In this talk NASA will highlight many of the advanced nondestructive evaluation efforts going on across the agency, as well as providing highlights for points of infusion for helping NASA meet its future mission goals.

NDE↗

NASA NTRSDate not supplied

Process Modeling of Woven Textiles

Woven polymer matrix composites offer numerous advantages over traditional unidirectional laminates. Processing conditions affect residual stress that builds up during manufacturing. This work proposes the analysis of three curing parameters on the local residual stress distribution of a plain weave textile architecture, including chemical shrinkage, the temperature cool down, and the evolution of matrix properties as a function of curing. Virtual curing is applied to the inter-tow matrix material of the plain weave Repeating Unit Cell (RUC) modeled in TexGen. Curing is implemented through user-written subroutines within the commercial software suite Abaqus. Results from process modeling are compared with a linear-elastic thermal cool down in Abaqus. A boundary conditions study is also conducted to compare the residual stress build up predicted by Flat(FBCs) and Periodic Boundary Conditions (PBCs). Preliminary results indicate that a thermal cool down over-estimates the end-of-cure stresses in the matrix. Process modeling is conducted with and without chemical shrinkage, then compared with a thermal cool down. Results show that 11.32% of the final stress state is due to chemical shrinkage. Material property evolution during curing also has a non-negligible effect on the end stress.

woven composites↗

NASA NTRS1979

Estimation of economic losses

If the concentration of carbon fibers (CF) is high after their dispersion due to an aircraft fire, there is a significant possibility that a number of residential, commercial, and industrial establishments might be affected by electronic equipment failure. Estimating economic losses from CF release involves characterizing an entire spectrum of buildings and electronic equipment within a given community. A number of simplified assumptions were made to reduce the data collection requirements to manageable proportions. A limited number of facility categories were identified, and assumed to be relatively homogeneous. The detailed examination of potential losses on an industry-by-industry basis is an important area for future investigation.

Source record↗

NASA NTRS1989

Manufacturing Aids

During a research program, MMTC/Textron invented a computer-aided automatic robotic system for spraying hot plasma onto a turbine blade. The need to control the thickness of the plasma deposit led to the development of advanced optical gaging techniques to monitor and control plasma spray build-up on blade surfaces. The techniques led to computerized optical gages for inspecting aircraft, industrial turbine blades, etc. MMTC offers 10 standard commercial robotic gages. The system also generates two dimensional profiles for assessing status and specifying repairs to the electromechanical cathodes used to make the parts. It is capable of accuracies to a ten-thousandth of an inch. An expanded product line is currently marketed. The gages offer multiple improvements in quality control and significant savings.

Source record↗

NASA NTRS2008

The Next Giant Leap: NASA's Ares Launch Vehicles Overview

The next chapter in NASA's history also promises to write the next chapter in America's history, as the Agency makes measurable strides toward developing new space transportation capabilities that wi!! put astronauts on course to explore the Moon as the next giant leap toward the first human footprint on Mars. This paper will present top-level plans and progress being made toward fielding the Ares I crew launch vehicle in the 2013 timeframe and the Ares V cargo launch vehicle in the 2018 timeframe. It also gives insight into the objectives for the first test flight, known as the Ares I-X, which is scheduled for April 2009. The U.S. strategy to scientifically explore space will fuel innovations such as solar power and water recycling, as well as yield new knowledge that directly benefits life on Earth. For the Ares launch vehicles, NASA is building on heritage hardware and unique capabilities; as well as almost 50 years of lessons learned from the Apollo Saturn, Space Shuttle, and commercial launch vehicle programs. In the Ares I Project's inaugural year, extensive trade studies and evaluations were conducted to improve upon the designs initially recommended by the Exploration Systems Architecture Study, resulting in significant reduction of near-term and long-range technical and programmatic risks; conceptual designs were analyzed for fitness against requirements; and the contractual framework was assembled to enable a development effort unparalleled in American space flight since the Space Shuttle. The Exploration Launch Projects team completed the Ares I System Requirements Review (SRR) at the end of 2006--the first such engineering milestone for a human-rated space transportation system in over 30 years.

Cook, Stephen A.↗

NASA NTRSDate not supplied

Containerized GEOS: Toward a Portable Climate Model

The NASA Goddard Earth Observing System (GEOS) is an Earth system model used for weather, climate, and other scientific applications. GEOS consists of linked components that can run in various configurations such as atmosphere-only and coupled atmosphere-ocean. Running this model on any new supercomputing system depends on operating systems, compilers, MPI stacks, and libraries being present and correctly configured. To remove that burden from users, our project explores building and running GEOS using Singularity containers – files containing all the needed software dependencies – on both NASA high-end computing systems and commercial cloud computing environments. Ultimately, the goal is for containerized GEOS to make it easier for users outside of NASA to deploy and run the model on any machine.

Matthew Thompson↗

NASA NTRS2015

Biomaterials Out of Thin Air: in Situ, On-Demand Printing of Advanced Biocomposites

Upmass is the single most significant limitation of our current space mission capability. Although biomaterials and biocomposites have mass, strength, flexibility, and self-healing properties that could significantly reduce upmass, their use is limited by the following drawbacks: Expensive, specific production. Many biomaterials can only be produced as part of significant support ecosystem; Inaccessible functional customization. The grain of wood, the porosity of bone, and so on are an integral part of the materials' desired mechanical properties, but are not deterministic when the material is naturally grown; Limited compositions. Most biomaterials (unlike metal, plastic, etc.) cannot be easily combined or modified to produce new materials. This project builds on recent advances in: Synthetic biology. Libraries of standardized genetic parts which can be used for controlled cellular material production, delivery, and binding; 3D printing. Commercial off-the-shelf components which can be used to make of a pico- to nanoliter cell deposition system; Tissue engineering. Proven cell-compatible support hydrogels and scaffolds can be modified to bind the deposited biomaterials of interest. Objectives: Feasibility and benefit analysis. Two mission contexts span the concept's scope (see below); Proof-of-concept demonstration. A simple grid of two proteins, fluorescent for easy detection, to validate the core technology concept; Proposed implementations for follow-on work. Avenues for future work on each core component (host cell, production control, material delivery, material binding, etc.); Complementary studies exploration. A survey of other emerging areas (in situ resource utilization, protein engineering, etc.) with the potential to multiply our technology's impact. Potential Impacts: This application could dramatically expand manufacturing capabilities on Earth and in space: In situ resource utilization. A far greater range of materials and products will be available from the limited palette offered by in situ resource extraction techniques; Reduced equipment and material upmass for off-Earth habitats. Ready- to-use highly specialized construction materials (radiation hardened, compressive/tensile, light or dense) from an extremely low starting mass; Structured biomaterial production. New ready-to-use macro, micro, and molecular manufacturing techniques for traditional biomaterials such as wood, bone and shell; New and novel biocomposite creation. The ability to create completely novel material composites from any base material that cells can be engineered to produce. Suggested Mission Contexts: ISS part manufacturing. A 'minimal working example' making a finished biomaterial part aboard the International Space Station; A long-term Mars habitat. 'Cradle-to-grave' use at a hypothetical Mars habitat, covering everything from tools to construction materials. Alternate Abstract: Imagine being able to print anything from tools and composite building materials to food and human tissues. Imagine being on Mars with the ability to replace any broken part, whether it's a part of your spacesuit, your habitat, or your own body. We propose a technique that would allow just that. By printing 3D arrays of cells engineered to secrete the necessary materials, the abundant in situ resources of atmosphere and regolith become organic, inorganic, or organic-inorganic composite materials. Such materials include novel, biologically derived materials not previously possible to fabricate.

habitats↗

NASA NTRS2015

Biomaterials Out of Thin Air: in Situ, On-demand Printing of Advanced Biocomposites

Upmass is the single most significant limitation of our current space mission capability. Although biomaterials and biocomposites have mass, strength, flexibility, and self-healing properties that could significantly reduce upmass, their use is limited by the following drawbacks: Expensive, specific production. Many biomaterials can only be produced as part of significant support ecosystem; Inaccessible functional customization. The grain of wood, the porosity of bone, and so on are an integral part of the materials' desired mechanical properties, but are not deterministic when the material is naturally grown; Limited compositions. Most biomaterials (unlike metal, plastic, etc.) cannot be easily combined or modified to produce new materials. This project builds on recent advances in: Synthetic biology. Libraries of standardized genetic parts which can be used for controlled cellular material production, delivery, and binding; 3D printing. Commercial off-the-shelf components which can be used to make of a pico- to nanoliter cell deposition system; Tissue engineering. Proven cell-compatible support hydrogels and scaffolds can be modified to bind the deposited biomaterials of interest. Objectives: Feasibility and benefit analysis. Two mission contexts span the concept's scope (see below); Proof-of-concept demonstration. A simple grid of two proteins, fluorescent for easy detection, to validate the core technology concept; Proposed implementations for follow-on work. Avenues for future work on each core component (host cell, production control, material delivery, material binding, etc.); Complementary studies exploration. A survey of other emerging areas (in situ resource utilization, protein engineering, etc.) with the potential to multiply our technology's impact. Potential Impacts: This application could dramatically expand manufacturing capabilities on Earth and in space: In situ resource utilization. A far greater range of materials and products will be available from the limited palette offered by in situ resource extraction techniques; Reduced equipment and material upmass for off-Earth habitats. Ready- to-use highly specialized construction materials (radiation hardened, compressive/tensile, light or dense) from an extremely low starting mass; Structured biomaterial production. New ready-to-use macro, micro, and molecular manufacturing techniques for traditional biomaterials such as wood, bone and shell; New and novel biocomposite creation. The ability to create completely novel material composites from any base material that cells can be engineered to produce. Suggested Mission Contexts: ISS part manufacturing. A 'minimal working example' making a finished biomaterial part aboard the International Space Station; A long-term Mars habitat. 'Cradle-to-grave' use at a hypothetical Mars habitat, covering everything from tools to construction materials. Alternate Abstract: Imagine being able to print anything from tools and composite building materials to food and human tissues. Imagine being on Mars with the ability to replace any broken part, whether it's a part of your spacesuit, your habitat, or your own body. We propose a technique that would allow just that. By printing 3D arrays of cells engineered to secrete the necessary materials, the abundant in situ resources of atmosphere and regolith become organic, inorganic, or organic-inorganic composite materials. Such materials include novel, biologically derived materials not previously possible to fabricate.

habitats↗

NASA NTRS1979

Performance verification of an air solar collector

Procedures and results of battery of qualification tests performed by independent certification agency on commercial solar collector are presented in report. Reported results were used as basis in judging collector suitable for field installation in residential and commerical buildings.

Miller, D. C.↗