Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Carbide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Amorphous silicon carbide high contrast gratings as highly efficient spectrally selective visible reflectors

We report spectrally selective visible wavelength reflectors using hydrogenated amorphous silicon carbide (a-SiC:H) as a high index contrast material. Beyond 610nm and through the near infrared spectrum, a-SiC:H exhibits very low loss and exhibits an wavelength averaged index of refraction of n = 3.1. Here we design, fabricate, and characterize such visible reflectors using a hexagonal array of a-SiC:H nanopillars as wavelength-selective mirrors with a stop-band of approximately 40 nm full-width at half maximum. The fabricated high contrast grating exhibits reflectivity R >94% at a resonance wavelength of 642nm with a single layer of a-SiC:H nanopillars. The resonance wavelength is tunable by adjusting the geometrical parameters of the a-SiC:H nanopillar array, and we observe a stop-band spectral center shift from 635 nm up to 642 nm. High contrast gratings formed from a-SiC:H nanopillars are a promising platform for various visible wavelength nanophotonics applications.

Bauser, Haley C.↗
DOE OSTI2020

Dynamically controlled random lasing with colloidal titanium carbide MXene

Control of lasing properties through tailorable and dynamically tunable materials and reconfigurable compositions can augment the performance of random lasers for a wide range of applications. Here, a colloid of randomly dispersed weakly scattering single-layer titanium carbide (Ti 3 C 2 T x ) MXene flakes embedded within rhodamine 101 gain medium is experimentally shown to provide feedback for random lasing. Additionally, in contrast to previously reported random laser systems where the optical properties of scatterers are static, the relative permittivity of Ti 3 C 2 T x MXene flakes can be varied under optical pumping due to the saturable absorption properties. Numerical simulations indicate that the observed nonlinear response of Ti 3 C 2 T x MXene flakes enables dynamically tunable random lasing. Thus, pumping the Ti 3 C 2 T x MXene flakes with a second optical source decreases the gain threshold required to obtain random lasing. Also, using numerical simulations, it is shown that the control over the intensity of the second pump enables tuning the field distribution of the random lasing modes. Considering the diversity of the MXenes family, the proposed MXene colloidal metamaterial design opens up a new avenue to advanced control of lasing properties for photonic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Triangular cross-section beam splitters in silicon carbide for quantum information processing

Abstract Triangular cross-section color center photonics in silicon carbide is a leading candidate for scalable implementation of quantum hardware. Within this geometry, we model low-loss beam splitters for applications in key quantum optical operations such as entanglement and single-photon interferometry. We consider triangular cross-section single-mode waveguides for the design of a directional coupler. We optimize parameters for a 50:50 beam splitter. Finally, we test the experimental feasibility of the designs by fabricating triangular waveguides in an ion beam etching process and identify suitable designs for short-term implementation.

42 ENGINEERING↗
DOE OSTI2022

Synthesis and Characterization of Silicon Carbide Ceramic Composites with CeO 2 Powder

This study pioneers the fabrication and characterization of silicon carbide (SiC) containing cerium dioxide (CeO 2 ). CeO 2 powder was tested as a surrogate for actinide oxide waste forms such as uranium dioxide (UO 2 ) and plutonium dioxide (PuO 2 ). Several syntheses were evaluated with varying amounts of preceramic polymer (SMP-10 resin) and CeO 2 containing either SiC fiber, carbon fiber, or no fibers. Scanning electron microscopy (SEM) was used to characterize morphology and compositional differences, and energy-dispersive x-ray spectroscopy (EDS) was used to provide semiquantitative elemental analysis. In addition, each sample was characterized by density, powder x-ray diffraction (pXRD), and Raman spectroscopy. Samples containing nearly more than four times CeO 2 powder than SMP-10 resin by mass had the best properties. This research establishes a unique synthesis for SiC containing high concentrations of CeO 2 powder to illustrate how it may be managed as a potential waste form.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Large-Scale Additive Manufacturing of Silicon Carbide with Process Monitoring

This report summarizes new capabilities in additive manufacturing (AM) of large-scale silicon carbide (SiC) components under the Advanced Materials and Manufacturing Technologies (AMMT) program. SiC is a promising material that is being considered for many advanced reactor designs due to its high temperature strength, radiation tolerance, minimal neutron absorption, and oxidation resistance [1-8]. One of the primary limitations to using SiC as an in-core structural material is the inability to fabricate large SiC components with complex geometries. While under the former Transformational Challenge Reactor (TCR) program, ceramic AM systems at the Oak Ridge National Laboratory (ORNL) were limited in the quantity and overall size achievable for producing ceramic AM components. To address this, ORNL has improved its infrastructure for binder jet and chemical vapor infiltration (CVI) processes with cutting-edge equipment coming online in a newly renovated laboratory space capable of producing larger components and higher throughput without compromise on part size. This report details the laboratory renovation progress, focusing specifically on the DesktopMetal (formerly ExOne) X25Pro binder jet, a large scale CVI furnace, and the added functionality of a software tool called Peregrine for quality assurance and control purposes.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Preshot Report for Carbonara: Dynamics of a Boron Carbide Sandwich

The main purpose of the Carbonara experiment is to provide much-needed data to inform physics modeling of boron carbide (B 4 C) subjected to a sweeping high explosive (HE) detonation. The proposed experiment will include three separate shots, each employing a rectangular slab of HE (4” × 3” × 1”) sandwiched between two wedges of B 4 C, see Fig.1. In each case the top B 4 C wedge tapers from a height of 2.5 cm to 0.5 cm, while the bottom wedge tapers from 1.5 cm to 0.5 cm. The wedges are 4” in the direction of the proton beam, and 3” in the direction transverse to the beam. Three shots are currently planned, each one using a different HE: PBX 9501, PBX 9502, and PBX 9701. The HE will be initiated using a line wave generator (LWG) to preserve planar symmetry, in conjunction with a Comp. B booster to smooth out the profile for the initial condition on the main charge and to aid in initiation of the PBX 9502 shot. In each case the booster spans the entire length and height of the main HE slab and extends 0.5” in toward the LWG.

36 MATERIALS SCIENCE↗
DOE OSTI2023

An ICME Modeling Framework for Metal Matrix Composites Focusing on Ultrahigh Temperature Matrix Material and Tungsten Carbide Reinforcement Particulate (Final CRADA Report)

Ultra High Temperature Metal Matrix Composites (UHT-MMCs) are of interest to the due to their potential defense and aerospace applications. These materials consist of a metal matrix reinforced with a stiff ceramic or cermet. Based on a preliminary literature survey, this project will focused on a pure titanium (Ti) matrix reinforced with tungsten carbide-cobalt (WC-Co). UHT-MMC technology is still at a nascent stage of development and requires extensive experimental work to optimize the structure and resulting material properties of a particular UHT-MMC material system. An accurate and complete high-performance computing (HPC) model of the Ti/WC-Co material system could greatly accelerate the development and deployment Ti/WC-Co materials by connecting processing parameters to material properties. This type of model could then be used in an integrated computational materials engineering approach to optimize the material structure to achieve a targeted level of performance.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Development of Binder Jet Compatible Silicon Carbide Mixtures for Increased Sintered Density

Binder jet additive manufacturing can process a variety of ceramic powder feedstocks to manufacture near net shape green parts that are subsequently sintered to achieve densification. In particular, silicon carbide (SiC) is a promising ceramic material for heat exchangers in energy storage applications and binder jet is a well-suited process for manufacturing these heat exchangers due to the often geometrically complex designs. However, the need for good powder flowability in binder jet printing often limits the feedstock powder to be larger particles rather than that of ultra fine submicron powders used in conventional ceramic processing, which are more readily densified during sintering. The present work explores the use of various powder mixtures and sintering settings to identify strategies for achieving high density sintered parts in binder jet compatible systems without the use of infiltration. Liquid-phase sintering additives and bimodal powder mixtures are explored alongside different sintering temperatures, rates, atmospheres, and hold times. Two mixtures were found to be good candidates for further exploration: 1) 90 wt% 0.6 µm SiC + 6.25 wt% Al 2 O 3 + 3.75 wt% Y 2 O 3 mixture achieved the highest sintered relative density of 91.2%; and 2) a bimodal mixture comprised of 45 wt% 10 µm SiC + 45 wt% 0.6 µm SiC + 6.25 wt% Al 2 O 3 + 3.75 wt% Y 2 O 3 had the best powder flowability of the powders measured and a 75.1% sintered relative density.

25 ENERGY STORAGE↗
DOE OSTI2023

Investigation of Carbide Inclusions in Cast Uranium [Slides]

Outline - Introduction: The motivations for the project, and some background on inclusions in uranium, and about the samples; Lath Inclusion Morphology: Looking at the morphology of a specific family of carbide inclusions in casting 20; Clustering of Lath Inclusions: Investigating the group behavior of these lath shaped inclusions from the inner to outer edges; Conclusions: Final thoughts on the lath inclusions and future work ideas.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Qualification of Commercially Available Silicon Carbide for Passive Thermometry in Reactor Experiments – FY23 Status Report

Silicon carbide (SiC) is often used as a passive temperature indicator for uninstrumented in-core nuclear experiments. For the past several decades, Oak Ridge National Laboratory has relied primarily on SiC thermometry manufactured by Dow Chemical Company, formerly Rohm and Haas because of the material’s high density and reduced grain boundary elements. Although Dow SiC has performed well in this application, this material is no longer commercially available, and a new supplier is needed for future experiments. To determine a suitable replacement, a study was initiated on five types of SiC from four commercial vendors. Several critical properties, including density, electrical resistivity, chemical purity, grain structure, crystal structure, and strength were measured in samples from each material. Additionally, thermometry specimens were manufactured for irradiation in the High Flux Isotope Reactor at nominal temperatures of 300°C, 600°C, and 900°C, which will be measured using continuous dilatometry at a later date. This report provides an update of commercially available SiC material characterization and the irradiation capsule design.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Distributed Temperature Profiles of Silicon Carbide Catalyst Bed in a Microwave Reactor using Fiber-optic Sensor

Microwave heating is of great interest for reducing greenhouse gas emissions of catalytic chemical conversion processes because it can heat up the reactants rapidly and efficiently and accelerate reaction rates. In microwave-assisted catalytic thermochemical conversion processes, accurate internal temperature measurement would help facilitate effective process control. Metallic thermocouples interfere and spark in the microwave heating environment, so they are not an option. Infrared pyrometers typically provide a single temperature value by averaging over a finite surface area of the catalyst bed. In this work, we use fiber-optic sensors passing through the catalyst bed to provide more accurate temperatures along the height of the catalyst bed. The fiber optic sensors are immune to the electromagnetic microwave radiation and provide temperature profiles along their length. Here, custom fiber-optic sensors were coupled to the optical distributed temperature sensing devices to measure the temperature profiles along the height of the catalyst bed at high temperatures with ~1 mm spatial resolution. The sensing devices use optical frequency domain reflectometry (OFDR) technique for distributed temperature measurement. This work shows the temperature profiles along the height of the silicon carbide powder catalyst bed in the variable and fixed frequency microwave reactors.

Thapa, Juddha↗
DOE OSTI2024

Lower length scale model for palladium attack of silicon carbide in TRISO fuel

TRistructural ISOtropic (TRISO) particle fuels rely on silicon carbide (SiC) as the primary barrier for metallic fission product (FP) release. Palladium (Pd) generated by fission degrades the SiC layer, resulting in the formation of lamellar layers of palladium silicides (PdxSi) and carbon (C) perpendicular to the direction of attack. The Pd attack has been hypothesized to be responsible for failure of the SiC layer and enhance FP release. To better understand and quantify Pd attack of SiC in TRISO particles, a multiscale, mechanistic model of Pd transport is being developed by the NEAMS program. Previous work provided an initial hypothesis for modeling lamellar microstructure formation in SiC due to Pd attack using a phase-field model. The work described in this report builds on the previous model by using molecular dynamics (MD) simulations to parameterize the phase-field model kinetics, and build a reduced order model in BISON using the improved mesoscale Pd penetration model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Binder Jet Additive Manufacturing of Silicon Carbide Solar Reactor (CRADA Report)

Achieving high powder packing density is critical in binder jet additive manufacturing (BJAM), as it directly influences the final part density, mechanical properties, and sintering behavior. Multi-modal powder blends, which combine particles of different sizes, have been explored as a strategy to optimize packing efficiency and minimize defects. In this study, bimodal and trimodal powder blends were obtained by mixing silicon carbide powder in three different sizes. These results show that increased powder density is achievable with bimodal powder blends but is reduced in trimodal blends, and it was found that a 13% increase in the powder tap density was achieved using a bimodal blend of powder. The powder size distribution of the bimodal blend was measured at various stages during binder jet additive manufacturing and, no measurable powder separation occurred even after eight prints. Overall, this study shows limited advantage to trimodal powder blends but good promise for trimodal blends for increasing printed density while maintaining reusability in the binder jet process.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2025

Binder jet additive manufacturing of silicon carbide solar reactor

Achieving high powder packing density is critical in binder jet additive manufacturing (BJAM), as it directly influences the final part density, mechanical properties, and sintering behavior. Multi-modal powder blends, which combine particles of different sizes, have been explored as a strategy to optimize packing efficiency and minimize defects. In this study, bimodal and trimodal powder blends were obtained by mixing silicon carbide powder in three different sizes. These results show that increased powder density is achievable with bimodal powder blends but is reduced in trimodal blends, and it was found that a 13% increase in the powder tap density was achieved using a bimodal blend of powder. The powder size distribution of the bimodal blend was measured at various stages during binder jet additive manufacturing and, no measurable powder separation occurred even after eight prints. Overall, this study shows limited advantage to trimodal powder blends but good promise for trimodal blends for increasing printed density while maintaining reusability in the binder jet process.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Automated Segmentation of Twin Boundaries in TRISO Silicon Carbide Using Deep Neural Networks

Coated particle fuels, such as the tristructural isotropic (TRISO) fuel particle, are essential for high-temperature gas reactor (HTGR) applications due to their efficiency and stability under normal and off-normal conditions. However, widespread commercialization and deployment of this technology for next-generation nuclear applications require robust quality assurance and quality control (QA/QC) methods linking fabrication, properties, and performance. Of the many important metrics for TRISO QA/QC, quantification of the silicon carbide (SiC) microstructure is critical because it correlates with fission product retention during irradiation. Previous work has shown extensive twinning of the SiC microstructure, which strongly affects microstructural metrics; however, twin grain boundaries are not expected play a significant role in fission product diffusion. This report summarizes the initial development, training, and testing of a machine learning image processing algorithm to detect twin grain boundaries in a backscattered electron image, which can be removed so that microstructural metrics can be recalculated for legacy data. Further development and deployment of this model will provide automated, scalable improvement of potential QA/QC methods for the SiC layer of TRISO particles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Optimization of boron carbide density using direct current sintering for use as sputtering sources at the National Ignition Facility

Several experimental trials were conducted to determine optimal sintering parameters and compositions for purchased boron carbide powder using spark plasma sintering/direct current sintering. Sputtering targets used to create ablators for the National Ignition Facility have been unable to survive post processing procedures suggesting that in-house fabrication may yield better results due to extended control.

36 MATERIALS SCIENCE↗