Results for “CFD simulations” — Page 15

NASA NTRS2022

Low-Speed Performance Enhancement using Localized Active Flow Control: Simulations, Scaling and Design of Localized Active Flow Control on the Common Research Model (4/4)

This report is dedicated to the application of localized AFC on the NASA CRM-HL wind tunnel model, with focus on the aileron application discussed in the CFD study (final report document #2). The experience developed for the Reference Aircraft guided the implementation on the CRM model. CFD evaluations are performed on a representative high-lift configuration, for a set of aileron deflections, and at relevant flow conditions. Alternative flow control actuator layouts are proposed and design consideration for practical integration into the existing CRM-HL model are set forth. The CFD simulations indicate that the aerodynamic performance improvements due to AFC obtained for the CRM-HL are consistent with those achieved for the Reference Aircraft. The observed changes in L/D are smaller than for the Reference Aircraft because the CRM has a higher leading edge sweep angle and a different relative aileron size. Conceptual design studies confirmed that the integration of an AFC equipped aileron into the existing wind tunnel model is feasible.

AFC↗

NASA NTRS1998

Virtual and Experimental Visualization of Flows in Packed Beds of Spheres Simulating Porous Media Flows

A videotape presentation of flow in a packed bed of spheres is provided. The flow experiment consisted of three principal elements: (1) an oil tunnel 76.2 mm by 76.2 mm in cross section, (2) a packed bed of spheres in regular and irregular arrays, and (3) a flow characterization methodology, either (a) full flow field tracking (FFFT) or (b) computational fluid dynamic (CFD) simulation. The refraction indices of the oil and the test array of spheres were closely matched, and the flow was seeded with aluminum oxide particles. Planar laser light provided a two-dimensional projection of the flow field, and a traverse simulated a three-dimensional image of the entire flow field. Light focusing and reflection rendered the spheres black, permitting visualization of the planar circular interfaces in both the axial and transverse directions. Flows were observed near the wall-sphere interface and within the set of spheres. The CFD model required that a representative section of a packed bed be formed and gridded, enclosing and cutting six spheres so that symmetry conditions could be imposed at all cross-boundaries. Simulations had to be made with the flow direction at right angles to that used in the experiments, however, to take advantage of flow symmetry. Careful attention to detail was required for proper gridding. The flow field was three-dimensional and complex to describe, yet the most prominent finding was flow threads, as computed in the representative 'cube' of spheres with face symmetry and conclusively demonstrated experimentally herein. Random packing and bed voids tended to disrupt the laminar flow, creating vortices.

Hendricks, R. C.↗

NASA NTRS2011

CFD-CAA Coupled Calculations of a Tandem Cylinder Configuration to Assess Facility Installation Effects

This paper presents a numerical assessment of acoustic installation effects in the tandem cylinder (TC) experiments conducted in the NASA Langley Quiet Flow Facility (QFF), an open-jet, anechoic wind tunnel. Calculations that couple the Computational Fluid Dynamics (CFD) and Computational Aeroacoustics (CAA) of the TC configuration within the QFF are conducted using the CFD simulation results previously obtained at NASA LaRC. The coupled simulations enable the assessment of installation effects associated with several specific features in the QFF facility that may have impacted the measured acoustic signature during the experiment. The CFD-CAA coupling is based on CFD data along a suitably chosen surface, and employs a technique that was recently improved to account for installed configurations involving acoustic backscatter into the CFD domain. First, a CFD-CAA calculation is conducted for an isolated TC configuration to assess the coupling approach, as well as to generate a reference solution for subsequent assessments of QFF installation effects. Direct comparisons between the CFD-CAA calculations associated with the various installed configurations allow the assessment of the effects of each component (nozzle, collector, etc.) or feature (confined vs. free jet flow, etc.) characterizing the NASA LaRC QFF facility.

Redonnet, Stephane↗

NASA NTRS2003

Large-Eddy Simulation Code Developed for Propulsion Applications

A large-eddy simulation (LES) code was developed at the NASA Glenn Research Center to provide more accurate and detailed computational analyses of propulsion flow fields. The accuracy of current computational fluid dynamics (CFD) methods is limited primarily by their inability to properly account for the turbulent motion present in virtually all propulsion flows. Because the efficiency and performance of a propulsion system are highly dependent on the details of this turbulent motion, it is critical for CFD to accurately model it. The LES code promises to give new CFD simulations an advantage over older methods by directly computing the large turbulent eddies, to correctly predict their effect on a propulsion system. Turbulent motion is a random, unsteady process whose behavior is difficult to predict through computer simulations. Current methods are based on Reynolds-Averaged Navier- Stokes (RANS) analyses that rely on models to represent the effect of turbulence within a flow field. The quality of the results depends on the quality of the model and its applicability to the type of flow field being studied. LES promises to be more accurate because it drastically reduces the amount of modeling necessary. It is the logical step toward improving turbulent flow predictions. In LES, the large-scale dominant turbulent motion is computed directly, leaving only the less significant small turbulent scales to be modeled. As part of the prediction, the LES method generates detailed information on the turbulence itself, providing important information for other applications, such as aeroacoustics. The LES code developed at Glenn for propulsion flow fields is being used to both analyze propulsion system components and test improved LES algorithms (subgrid-scale models, filters, and numerical schemes). The code solves the compressible Favre-filtered Navier- Stokes equations using an explicit fourth-order accurate numerical scheme, it incorporates a compressible form of Smagorinsky s model for the subgrid-scale turbulence, and it uses generalized curvilinear coordinates to allow analysis of a wide range of geometries. The code runs in parallel on shared memory multiprocessor computers and is written in Fortran 90 with dynamic memory allocation. A sample result for a Mach-1.4 round jet is presented in the figure. Instantaneous Mach number contours in several cross-planes downstream of the nozzle exit are shown, illustrating how an LES captures the large unsteady three-dimensional turbulent structures present in the jet.

DeBonis, James R.↗

NASA NTRS1999

A Design Tool for Liquid Rocket Engine Injectors

A practical design tool for the analysis of flowfields near the injector face has been developed and used to analyze the Fastrac engine. The objective was to produce a computational design tool which was detailed enough to predict the interactive effects of injector element impingement angles and points and the momenta of the individual orifice flows. To obtain a model which could be used to simulate a significant number of individual orifices, a homogeneous computational fluid dynamics model was developed. To describe liquid and vapor sub- and super-critical flows, the model included thermal and caloric equations of state which were valid over a wide range of pressures and temperatures. A homogeneous model was constructed such that the local state of the flow was determined directly, i.e. the quality of the flow was calculated. Such a model does not identify drops or their distribution, but it does allow the flow along the injector face and into the acoustic cavity to be predicted. It also allows the film coolant flow to be accurately described. The initial evaluation of the injector code was made by simulating cold flow from an unlike injector element and from a like-on-like overlapping fan (LOL) injector element. The predicted mass flux distributions of these injector elements compared well to cold flow test results. These are the same cold flow tests which serve as the data base for the JANNAF performance prediction codes. The flux distributions 1 inch downstream of the injector face are very similar; the differences were somewhat larger at further distances from the faceplate. Since the cold flow testing did not achieve good mass balances when integrations across the entire fan were made, the CFD simulation appears to be reasonable alternative to future cold flow testing. To simulate the Fastrac, an RP-1/LOX combustion model must be chosen. This submodel must be relatively simple to accomplish three-dimensional, multiphase flow simulations. Single RP-1 pyrolysis and partial oxidation steps were chosen and the combustion was completed with the wet CO mechanism. Soot was also formed with a single global reaction. To validate the combustion submodel, global data from gas generator tests and from subscale motor test were used to predict qualitatively correct mean molecular weights, temperature, and soot levels. Because such tests do not provide general kinetics rates, the methodology is not necessarily appropriate for other than rocket type flows conditions. Soot predictions were made so that radiation heating to the motor walls can be made. These initial studies of the Fastrac were for a small region close to the injector face and chamber wall which included a segment of the acoustic cavity. The region analyzed includes 11 individual orifice holes to represent the LOL elements and the H2 film coolant holes. Typical results of this simulation are shown in Figure 1. At this point the only available test data to verify the predictions are temperatures measured in the acoustic cavity. These temperatures are in reasonable agreement at about 2000R (1111 K). Future work is expected to include improving the computational efficiency or the CFD model and/or using more computer capacity than the single Pentium PC with which these simulations were made.

Farmer, Richard C.↗

NASA NTRS2017

MiniWall Tool for Analyzing CFD and Wind Tunnel Large Data Sets

It is challenging to review and assimilate large data sets created by Computational Fluid Dynamics (CFD) simulations and wind tunnel tests. Over the past 10 years, NASA Ames Research Center has developed and refined a software tool dubbed the "MiniWall" to increase productivity in reviewing and understanding large CFD‐generated data sets. Under the recent NASA ERA project, the application of the tool expanded to enable rapid comparison of experimental and computational data. The MiniWall software is browser based so that it runs on any computer or device that can display a web page. It can also be used remotely and securely by using web server software such as the Apache HTTP Server. The MiniWall software has recently been rewritten and enhanced to make it even easier for analysts to review large data sets and extract knowledge and understanding from these data sets. This paper describes the MiniWall software and demonstrates how the different features are used to review and assimilate large data sets.

Data Analysis↗

NASA NTRSDate not supplied

Multiscale Mesh Adaptation for Transonic Aeroelastic Flutter Problems

This work applies multiscale mesh adaptation with refine to reduce spatial discretization error of aeroelastic computational fluid dynamics (CFD) simulations. Benchmark flutter models, such as the pitch and plunge NACA64A-010 airfoil and the benchmark supercritical wing, are studied with both a linearized frequency-domain solver and time-marching CFD coupled to a modal structural solver in FUN3D. The undeformed NASA Common Research Model (CRM), an aeroelastic jig shape variant of the CRM, is also studied with the linearized frequency-domain approach. For these cases, the adaptation process converges to comparable flutter predictions to hand-generated meshes but with smaller node counts. However the additional disciplines of the linearized frequency-domain analysis, the mesh deformation, and the unsteady finite-volume solver create robustness challenges that need to be addressed before it can be applied as a fully automated process for complex transonic aeroelastic problems. In particular, negative volumes are observed to be an issue for FUN3D’s linear elasticity mesh deformation solver when moving the adapted meshes.

Aeroelasticity↗

NASA NTRS2017

MiniWall Tool for Analyzing CFD and Wind Tunnel Large Data Sets

It is challenging to review and assimilate large data sets created by Computational Fluid Dynamics (CFD) simulations and wind tunnel tests. Over the past 10 years, NASA Ames Research Center has developed and refined a software tool dubbed the MiniWall to increase productivity in reviewing and understanding large CFD-generated data sets. Under the recent NASA ERA project, the application of the tool expanded to enable rapid comparison of experimental and computational data. The MiniWall software is browser based so that it runs on any computer or device that can display a web page. It can also be used remotely and securely by using web server software such as the Apache HTTP server. The MiniWall software has recently been rewritten and enhanced to make it even easier for analysts to review large data sets and extract knowledge and understanding from these data sets. This paper describes the MiniWall software and demonstrates how the different features are used to review and assimilate large data sets.

Computational Fluid Dyanmics↗

NASA NTRS1996

Performance Improvement Through Indexing of Turbine Airfoils: Numerical Simulation - Part 2

An experimental/analytical study has been conducted to determine the performance improvements achievable by circumferentially indexing succeeding rows of turbine stator airfoils. A series of tests was conducted to experimentally investigate stator wake clocking effects on the performance of the space shuttle main engine (SSME) alternate turbopump development (ATD) fuel turbine test article (TTA). The results from this study indicate that significant increases in stage efficiency can be attained through application of this airfoil clocking concept. Details of the experiment and its results are documented in part 1 of this paper. In order to gain insight into the mechanisms of the performance improvement, extensive computational fluid dynamics (CFD) simulations were executed. The subject of the present paper is the initial results from the CFD investigation of the configurations and conditions detailed in part 1 of the paper. To characterize the aerodynamic environments in the experimental test series, two-dimensional (2D), time accurate, multistage, viscous analyses were performed at the TTA midspan. Computational analyses for five different circumferential positions of the first stage stator have been completed. Details of the computational procedure and the results are presented. The analytical results verify the experimentally demonstrated performance improvement and are compared with data whenever possible. Predictions of time-averaged turbine efficiencies as well as gas conditions throughout the flow field are presented. An initial understanding of the turbine performance improvement mechanism based on the results from this investigation is described.

Griffin, Lisa W.↗

NASA NTRS2006

Aerothermodynamic Analyses of Towed Ballutes

A ballute (balloon-parachute) is an inflatable, aerodynamic drag device for application to planetary entry vehicles. Two challenging aspects of aerothermal simulation of towed ballutes are considered. The first challenge, simulation of a complete system including inflatable tethers and a trailing toroidal ballute, is addressed using the unstructured-grid, Navier-Stokes solver FUN3D. Auxiliary simulations of a semi-infinite cylinder using the rarefied flow, Direct Simulation Monte Carlo solver, DSV2, provide additional insight into limiting behavior of the aerothermal environment around tethers directly exposed to the free stream. Simulations reveal pressures higher than stagnation and corresponding large heating rates on the tether as it emerges from the spacecraft base flow and passes through the spacecraft bow shock. The footprint of the tether shock on the toroidal ballute is also subject to heating amplification. Design options to accommodate or reduce these environments are discussed. The second challenge addresses time-accurate simulation to detect the onset of unsteady flow interactions as a function of geometry and Reynolds number. Video of unsteady interactions measured in the Langley Aerothermodynamic Laboratory 20-Inch Mach 6 Air Tunnel and CFD simulations using the structured grid, Navier-Stokes solver LAURA are compared for flow over a rigid spacecraft-sting-toroid system. The experimental data provides qualitative information on the amplitude and onset of unsteady motion which is captured in the numerical simulations. The presence of severe unsteady fluid - structure interactions is undesirable and numerical simulation must be able to predict the onset of such motion.

Gnoffo, Peter A.↗

NASA NTRSDate not supplied

Attitude Reconstruction of Free-Flight CFD Generated Trajectories Using Non-Linear Pitch Damping Coefficient Curves

Attitude history reconstruction of Free-flight CFD generated trajectories with non-linear pitch damping coefficient curves is investigated. Free-flight CFD simulations of the capsule shape used for the Genesis sample return mission and the upcoming Dragonfly mission to Titan are conducted for 1-, 2-, and 3-degree-of-freedom cases. Two different data reduction methodologies are employed to derive a pitch damping curve as a function of instantaneous angle of attack. These curves are then used to reconstruct the attitude history of the body which is compared to the raw simulation results. While both data reduction methods produce pitch damping curves that can generally reconstruct the motion seen in the Free-flight simulations, it is found that optimization of the pitch damping curve using an inverse estimation process yields superior and more generalizable results. Further refinement of this technique could allow pitch damping curves derived using CFD to serve as a capability complementary to existing techniques for dynamic stability characterization.

entry↗

NASA NTRSDate not supplied

Attitude Reconstruction of Free-Flight CFD Generated Trajectories Using Non-Linear Pitch Damping Coefficient Curves

Attitude history reconstruction of Free-flight CFD generated trajectories with non-linear pitch damping coefficient curves is investigated. Free-flight CFD simulations of the capsule shape used for the Genesis sample return mission and the upcoming Dragonfly mission to Titan are conducted for 1-, 2-, and 3-degree-of-freedom cases. Two different data reduction methodologies are employed to derive a pitch damping curve as a function of instantaneous angle of attack. These curves are then used to reconstruct the attitude history of the body which is compared to the raw simulation results. While both data reduction methods produce pitch damping curves that can generally reconstruct the motion seen in the Free-flight simulations, it is found that optimization of the pitch damping curve using an inverse estimation process yields superior and more generalizable results. Further refinement of this technique could allow pitch damping curves derived using CFD to serve as a capability complementary to existing techniques for dynamic stability characterization.

entry↗

NASA NTRS2017

Two-Pendulum Model of Propellant Slosh in Europa Clipper PMD Tank

The objective of this fluids analysis is to model propellant slosh for the Europa Clipper mission using a two-pendulum model, such that controls engineers can predict slosh behavior during the mission. Propellant slosh causes shifts in center of mass and exerts forces and torques on the spacecraft which, if not adequately controlled, can lead to mission failure. The two-pendulum model provides a computationally simple model that can be used to predict slosh for the Europa Clipper tank geometry. The Europa Clipper tank is cylindrical with a domed top and bottom and includes a propellant management device (PMD). Due to the lack of experimental data in low gravity environments, computational fluid dynamics (CFD) simulation results were used as 'real' slosh behavior for two propellants at three fill fractions. Key pendulum parameters were derived that allow the pendulum model's center of mass, forces, and moments to closely match the CFD data. The parameter trends were examined as a function of tank fill fraction and compared with solutions to analytic equations that describe the frequency of slosh in tanks with simple geometries. The trends were monotonic as expected, and parameters resembled analytical predictions; any differences could be explained by the specific differences in the geometry of the tank. This paper summarizes the new method developed at Goddard Space Flight Center (GSFC) for deriving pendulum parameters for two-pendulum equivalent sloshing models. It presents the results of this method and discusses the validity of the results. This analysis is at a completed stage and will be applied in the immediate future to the evolving tank geometry as Europa Clipper moves past its preliminary design review (PDR) phase.

Propellant Slosh↗

NASA NTRS2020

Optimizing Performance and Accuracy with LIFQWIK

For the 2020 Summer Internship period, optimization and analysis was performed of a new iteration of the LIFQWIK PLIF model, used to evaluate the accuracy of CFD simulations of fuel injector performance. This presentation details the accuracy and performance optimization steps taken and presents the results of that optimization.

CFD↗

NASA NTRSDate not supplied

Boundary-Layer Flow Simulations Over Ablating Woven Thermal Protection System Material

Spallation is the mechanical removal of small chunks of material gets removed typically due to high shear conditions of the flow field. This reduces the ability of the thermal protection system (TPS) material to protect the spacecraft as well as cause turbulence in the flow causing higher heating rates. In this work, we focus on the material removal through ablation and high shear flow within the boundary layer region of woven TPS material. Woven TPS (WTPS) material is the latest class of material developed by NASA, to be used within the next generation of space flights. They are complex interlocked weaves designed to create a rigid structure that is highly resistant to heat and can be easily designed and tailored for a wide variety of entry environments. Due to material removal resulting from chemical degradation, the structural integrity of TPS material is affected. Spallation occurs when this structurally compromised material is exposed to the high shear flow conditions within the boundary layer. In order to understand the spallation mechanism within WTPS material, we first perform the material removal simulations which occur primarily through oxidation to obtain the microstructure at various stages of degradation. These simulations are performed using the Porous Microstructure Analysis (PuMA) software developed at NASA Ames. The micro-structure geometry used within these simulations were generated artificially to be similar to the 3D weave architecture of MSR-EEV (Mars Sample Return - Earth Entry Vehicle). The various eroded TPS micro-structures are then subjected to the boundary layer flow conditions to obtain critical surface quantities which contribute to the structural failure mechanism such as heat flux, pressure, and shear stress. The direct simulation Monte Carlo (DSMC) methodology is used to perform these simulations in order to accurately capture the strong gradients within the high-temperature boundary layer flow over the intricate geometry of WTPS material. The boundary layer profile is directly taken from the Computational Fluid Dynamics (CFD) simulation and provided as boundary conditions to the DSMC inlet and outlet. Further, the variation of these properties as the microstructure undergoes changes due to oxidation is also investigated. Finally, these quantities are used as input in PuMA to understand the material expansion/compression and strain within the woven TPS geometry and help in developing a comprehensive spallation and structure failure model.

microstructure↗

NASA NTRSDate not supplied

Boundary-Layer Flow Simulations Over Ablating Woven Thermal Protection System Material

Spallation is the mechanical removal of small chunks of material gets removed typically due to high shear conditions of the flow field. This reduces the ability of the thermal protection system (TPS) material to protect the spacecraft as well as cause turbulence in the flow causing higher heating rates. In this work, we focus on the material removal through ablation and high shear flow within the boundary layer region of woven TPS material. Woven TPS (WTPS) material is the latest class of material developed by NASA, to be used within the next generation of space flights. They are complex interlocked weaves designed to create a rigid structure that is highly resistant to heat and can be easily designed and tailored for a wide variety of entry environments. Due to material removal resulting from chemical degradation, the structural integrity of TPS material is affected. Spallation occurs when this structurally compromised material is exposed to the high shear flow conditions within the boundary layer. In order to understand the spallation mechanism within WTPS material, we first perform the material removal simulations which occur primarily through oxidation to obtain the microstructure at various stages of degradation. These simulations are performed using the Porous Microstructure Analysis (PuMA) software developed at NASA Ames. The micro-structure geometry used within these simulations were generated artificially to be similar to the 3D weave architecture of MSR-EEV (Mars Sample Return - Earth Entry Vehicle). The various eroded TPS micro-structures are then subjected to the boundary layer flow conditions to obtain critical surface quantities which contribute to the structural failure mechanism such as heat flux, pressure, and shear stress. The direct simulation Monte Carlo (DSMC) methodology is used to perform these simulations in order to accurately capture the strong gradients within the high-temperature boundary layer flow over the intricate geometry of WTPS material. The boundary layer profile is directly taken from the Computational Fluid Dynamics (CFD) simulation and provided as boundary conditions to the DSMC inlet and outlet. Further, the variation of these properties as the microstructure undergoes changes due to oxidation is also investigated. Finally, these quantities are used as input in PuMA to understand the material expansion/compression and strain within the woven TPS geometry and help in developing a comprehensive spallation and structure failure model.

microstructure↗

NASA NTRS2017

Pressurization of a Flightweight, Liquid Hydrogen Tank: Evaporation & Condensation at a Liquid/Vapor Interface

This paper presents an analysis and simulation of evaporation and condensation at a motionless liquid/vapor interface. A 1-D model equation, emphasizing heat and mass transfer at the interface, is solved in two ways, and incorporated into a subgrid interface model within a CFD simulation. Simulation predictions are compared with experimental data from the CPST Engineering Design Unit tank, a cryogenic fluid management test tank in 1-g. The numerical challenge here is the physics of the liquid/vapor interface; pressurizing the ullage heats it by several degrees, and sets up an interfacial temperature gradient that transfers heat to the liquid phase-the rate limiting step of condensation is heat conducted through the liquid and vapor. This physics occurs in thin thermal layers O(1 mm) on either side of the interface which is resolved by the subgrid interface model. An accommodation coefficient of 1.0 is used in the simulations which is consistent with theory and measurements. This model is predictive of evaporation/condensation rates, that is, there is no parameter tuning.

Stewart, Mark E. M.↗

NASA NTRS2013

A Computational Fluid Dynamics Study of Swirling Flow Reduction by using Anti-vortex Baffle

An anti-vortex baffle is a liquid propellant management device placed adjacent to an outlet of the propellant tank. Its purpose is to substantially reduce or eliminate the formation of free surface dip and vortex, as well as prevent vapor ingestion into the outlet, as the liquid drains out through the flight. To design an effective anti-vortex baffle, Computational Fluid Dynamic (CFD) simulations were undertaken for the NASA Ares I vehicle LOX tank subjected to the simulated flight loads with and without the anti-vortex baffle. The Six Degree-Of-Freedom (6- DOF) dynamics experienced by the Crew Launch Vehicle (CLV) during ascent were modeled by modifying the momentum equations in a CFD code to accommodate the extra body forces from the maneuvering in a non-inertial frame. The present analysis found that due to large moments, the CLV maneuvering has significant impact on the vortical flow generation inside the tank. Roll maneuvering and side loading due to pitch and yaw are shown to induce swirling flow. The vortical flow due to roll is symmetrical with respect to the tank centerline, while those induced by pitch and yaw maneuverings showed two vortices side by side. The study found that without the anti-vortex baffle, the swirling flow caused surface dip during the late stage of drainage and hence early vapor ingestion. The flow can also be non-uniform in the drainage pipe as the secondary swirling flow velocity component can be as high as 10% of the draining velocity. An analysis of the vortex dynamics shows that the swirling flow in the drainage pipe during the Upper Stage burn is mainly the result of residual vortices inside the tank due to conservation of angular momentum. The study demonstrated that the swirling flow in the drainage pipe can be effectively suppressed by employing the anti-vortex baffle.

Yang, H. Q.↗