Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ascent”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

A real-time guidance algorithm for aerospace plane optimal ascent to low earth orbit

Problems of onboard trajectory optimization and synthesis of suitable guidance laws for ascent to low Earth orbit of an air-breathing, single-stage-to-orbit vehicle are addressed. A multimode propulsion system is assumed which incorporates turbojet, ramjet, Scramjet, and rocket engines. An algorithm for generating fuel-optimal climb profiles is presented. This algorithm results from the application of the minimum principle to a low-order dynamic model that includes angle-of-attack effects and the normal component of thrust. Maximum dynamic pressure and maximum aerodynamic heating rate constraints are considered. Switching conditions are derived which, under appropriate assumptions, govern optimal transition from one propulsion mode to another. A nonlinear transformation technique is employed to derived a feedback controller for tracking the computed trajectory. Numerical results illustrate the nature of the resulting fuel-optimal climb paths.

Calise, A. J.↗

Independent Orbiter Assessment (IOA): Assessment of the ascent thrust vector control actuator subsystem FMEA/CIL

The results of the Independent Orbiter Assessment (IOA) of the Failure Modes and Effects Analysis (FMEA) and Critical Items List (CIL) are presented. The IOA effort first completed an analysis of the Ascent Thrust Vector Control Actuator (ATVD) hardware, generating draft failure modes and potential critical items. To preserve independence, this analysis was accomplished without reliance upon the results contained within the NASA FMEA/CIL documentation. The IOA results were then compared to the NASA FMEA/CIL baseline with proposed Post 51-L updates included. A resolution of each discrepancy from the comparison is provided through additional analysis as required. This report documents the results of that comparison for the Orbiter ATVC hardware. The IOA product for the ATVC actuator analysis consisted of 25 failure mode worksheets that resulted in 16 potential critical items being identified. Comparison was made to the NASA baseline which consisted of 21 FMEAs and 13 CIL items. This comparison produced agreement on all CIL items. Based on the Pre 51-L baseline, all non-CIL FMEAs were also in agreement.

Wilson, R. E.↗

The engineering of a nuclear thermal landing and ascent vehicle utilizing indigenous Martian propellant

A design study of a novel space transportation concept called NIMF (Nuclear rocket using Indigenous Martian Fuel) is reported. In this concept, Martian CO2 gas, which constitutes 95 percent of the atmosphere, is liquified by simple compression to about 100 psi and remains stable without refrigeration. When heated and exhausted out of a rocket nozzle, a specific impulse of about 264 s can be achieved, sufficient for flights from the surface to highly energetic orbits or from one point on the surface to any other point. The propellant acquisition system can travel with the vehicle, allowing it to refuel itself each time it lands. The concept offers unequalled potential to achieve planetwide mobility, allowing complete global access for the exploration of Mars. By eliminating the necessity of transporting ascent propellant to Mars, the NIMF can also significantly reduce the initial mass in LEO and of a manned Mars mission.

Zubrin, Robert M.↗

Research and development for Onboard Navigation (ONAV) ground based expert/trainer system: Preliminary ascent knowledge requirements

The preliminary version of expert knowledge for the Onboard Navigation (ONAV) Ground Based Expert Trainer Ascent system for the space shuttle is presented. Included is some brief background information along with the information describing the knowledge the system will contain. Information is given on rules and heuristics, telemetry status, landing sites, inertial measurement units, and a high speed trajectory determinator (HSTD) state vector.

Bochsler, Daniel C.↗

Operational efficiency: Automatic ascent flight design

Major objectives, milestones, key contacts, major accomplishments, technology issues, and candidate programs of the automatic ascent flight design are outlined. Topics discussed include: advanced avionics concepts; advanced training concepts; telerobotics/telepresence; integrated command and control; advanced software integration; atmospheric adaptive guidance; and health status and monitoring concept. This presentation is represented by viewgraphs only.

Source record↗

Flow computations for the Space Shuttle in ascent mode using thin-layer Navier-Stokes equations

The application of CFD techniques to the Space Shuttle ascent environment was aggressively undertaken in the wake of the Challenger accident in order to secure a major new source of aerodynamic information for both the nominal and mission-abort conditions, using Cray 2 and Cray YMP supercomputers. Due to the integrated vehicle's complexity, the 'chimera' composite grid approach, in which an overset body-conforming grid is used to represent each geometric component as well as special flow regions, was employed for the discretization process. Calculation results exhibit general agreement in both flow structure and surface pressure with the available wind tunnel and flight-test results.

Martin, F. W., Jr.↗

Ascent performance of an air-breathing horizontal-takeoff launch vehicle

Simulations are conducted to investigate a proposed NASA launch vehicle that is fully reusable, takes off horizontally, and uses airbreathing propulsion in a single stage. The propulsion model is based on a cycle analysis method, and the vehicle is assumed to be a rigid structure with distributed fuel, operating under a range of atmospheric conditions. The program to optimize simulated trajectories (POST) is modified to include a predictor-corrector guidance capability and then used to generate the trajectories. Significant errors are encountered during the unpowered coast phase due to uncertainty in the atmospheric density profile. The amount of ascent propellant needed is shown to be directly related to the thrust-vector angle and the location of the center of gravity of the vehicle because of the importance of aim-drag losses to total ideal velocity.

Powell, Richard W.↗

Results of the space shuttle vehicle ascent air data system probe calibration test using a 0.07-scale external tank forebody model (68T) in the AEDC 16-foot transonic wind tunnel (IA-310), volume 1

A recalibration of the Space Shuttle Vehicle Ascent Air Data System probe was conducted in the Arnold Engineering Development Center (AEDC) transonic wind tunnel. The purpose was to improve on the accuracy of the previous calibration in order to reduce the existing uncertainties in the system. A probe tip attached to a 0.07-scale External Tank Forebody model was tested at angles of attack of -8 to +4 degrees and sideslip angles of -4 to +4 degrees. High precision instrumentation was used to acquire pressure data at discrete Mach numbers ranging from 0.6 to 1.55. Pressure coefficient uncertainties were estimated at less than 0.0020. Data is given in graphical and tabular form.

Collette, J. G. R.↗

Results of the space shuttle vehicle ascent air data system probe calibration test using a 0.07-scale external tank forebody model (68T) in the AEDC 16-foot transonic wind tunnel (IA-310), volume 2

A recalibration of the Space Shuttle Vehicle Ascent Air Data System probe was conducted in the Arnold Engineering and Development Center (AEDC) transonic wind tunnel. The purpose was to improve on the accuracy of the previous calibration in order to reduce the existing uncertainties in the system. A probe tip attached to a 0.07-scale External Tank Forebody model was tested at angles of attack of -8 to +4 degrees and sideslip angles of -4 to +4 degrees. High precision instrumentation was used to acquire pressure data at discrete Mach numbers ranging from 0.6 to 1.55. Pressure coefficient uncertainties were estimated at less than 0.0020. Additional information is given in tabular form.

Collette, J. G. R.↗

Propulsion systems using in situ propellants for a Mars ascent vehicle

The indigenous propellants of oxygen and carbon monoxide were studied for use in a Mars Ascent Vehicle (MAV). Both the oxygen and carbon monoxide were evaluated as turbine working fluids for a full expander engine cycle used in the MAV. Two oxygen working fluid engines and four carbon monoxide engines were investigated. The maximum hot-gas-side wall temperature was limited to either 445 K (800 R) or 556 K (1000 R) over a range of working fluid mass flows. An engine thrust of 44.5 kN (1,000 lb(sub f)) was assumed. The engine characteristics of coolant inlet pressure, total engine length, specific impulse, pump efficiencies, and turbine power required were optimized. Of the six engines evaluated, the study showed that either type of working fluid was feasible for a MAV engine. Using carbon monoxide as the working fluid resulted in the best engine characteristics.

Wadel, Mary F.↗

Propulsion systems using in situ propellants for a Mars Ascent Vehicle

The indigenous propellants of oxygen and carbon monoxide were studied for use in a Mars Ascent Vehicle (MAV). Both the oxygen and carbon monoxide were evaluated as turbine working fluids for a full expander engine cycle used in the MAV. Two oxygen working fluid engines and four carbon monoxide engines were investigated. The maximum hot-gas-side wall temperature was limited to either 445 K (800R) or 556 K (1000 R) over a range of working fluid mass flows. An engine thrust of 44.5 kN (1,000 lb(sub f)) was assumed. The engine characteristics of coolant inlet pressure, total engine length, specific impulse, pump efficiencies, and turbine power required were optimized. Of the six engines evaluated, the study showed that either type of working fluid was feasible for a MAV engine. Using carbon monoxide as the working fluid resulted in the best engine characteristics.

Wadel, Mary F.↗

Effect of inert propellant injection on Mars ascent vehicle performance

A Mars ascent vehicle is limited in performance by the amount of propellant which can be brought from earth. In some cases the vehicle performance can be improved by injecting inert gas into the engine, if the inert gas is available as an in situ resource. CO2, N2 and Ar are constituents of the Martian atmosphere which are available at every point on the Martian surface and could be produced by a very simple processing technique, consisting essentially of compressing the atmosphere. The effect of inert gas injection on rocket engine performance was analyzed with a numerical code calculating chemical equilibrium in the engine, for engines of varying combustion chamber pressure, expansion ratio, oxidizer/fuel ratio, and inert injection fraction. Results of this analysis were applied to several candidate missions to determine how the required mass of return propellant needed in LEO could be decreased using inert propellant injection.

Colvin, James E.↗

Effect of inert propellant injection on Mars ascent vehicle performance

A Mars ascent vehicle is limited in performance by the propellant which can be brought from Earth. In some cases the vehicle performance can be improved by injecting inert gas into the engine, if the inert gas is available as an in-situ resource and does not have to be brought from Earth. Carbon dioxide, nitrogen, and argon are constituents of the Martian atmosphere which could be separated by compressing the atmosphere, without any chemical processing step. The effect of inert gas injection on rocket engine performance was analyzed with a numerical combustion code that calculated chemical equilibrium for engines of varying combustion chamber pressure, expansion ratio, oxidizer/fuel ratio, and inert injection fraction. Results of this analysis were applied to several candidate missions to determine how the required mass of return propellant needed in low Earth orbit could be decreased using inert propellant injection.

Colvin, James E.↗

Minimum Hamiltonian ascent trajectory evaluation (MASTRE) program (update to automatic flight trajectory design, performance prediction, and vehicle sizing for support of shuttle and shuttle derived vehicles) users manual

Documentation for the User Interface Program for the Minimum Hamiltonian Ascent Trajectory Evaluation (MASTRE) is provided. The User Interface Program is a separate software package designed to ease the user input requirements when using the MASTRE Trajectory Program. This document supplements documentation on the MASTRE Program that consists of the MASTRE Engineering Manual and the MASTRE Programmers Guide. The User Interface Program provides a series of menus and tables using the VAX Screen Management Guideline (SMG) software. These menus and tables allow the user to modify the MASTRE Program input without the need for learning the various program dependent mnemonics. In addition, the User Interface Program allows the user to modify and/or review additional input Namelist and data files, to build and review command files, to formulate and calculate mass properties related data, and to have a plotting capability.

Lyons, J. T.↗

The engineering of a nuclear thermal landing and ascent vehicle utilizing indigenous Martian propellant

The following paper reports on a design study of a novel space transportation concept known as a 'NIMF' (Nuclear rocket using Indigenous Martian Fuel). The NIMF is a ballistic vehicle which obtains its propellant out of the Martian air by compression and liquefaction of atmospheric CO2. This propellant is subsequently used to generate rocket thrust at a specific impulse of 264 s by being heated to high temperature (2800 K) gas in the NIMFs' nuclear thermal rocket engines. The vehicle is designed to provide surface to orbit and surface to surface transportation, as well as housing, for a crew of three astronauts. It is capable of refueling itself for a flight to its maximum orbit in less than 50 days. The ballistic NIMF has a mass of 44.7 tonnes and, with the assumed 2800 K propellant temperature, is capable of attaining highly energetic (250 km by 34,000 km elliptical) orbits. This allows it to rendezvous with interplanetary transfer vehicles which are only very loosely bound into orbit around Mars. If a propellant temperature of 2000 K is assumed, then low Mars orbit can be attained; while if 3100 K is assumed, then the ballistic NIMF is capable of injecting itself onto a minimum energy transfer orbit to Earth in a direct ascent from the Martian surface.

Zubrin, Robert M.↗

Autonomous Mars ascent and orbit rendezvous for earth return missions

The details of tha assessment of autonomous Mars ascent and orbit rendezvous for earth return missions are presented. Analyses addressing navigation system assessments, trajectory planning, targeting approaches, flight control guidance strategies, and performance sensitivities are included. Tradeoffs in the analysis and design process are discussed.

Edwards, H. C.↗

Closed form solutions of constrained trajectories - Application in optimal ascent of aerospace plane

The present consideration of the flight trajectory of hypersonic aerospace vehicles subject to a class of path constraints notes the constrained dynamics to constitute a natural two-timescale system, so that problems of trajectory optimization and guidance can be dramatically simplified by means of the asymptotic analytical solutions thus obtained. An illustrative application in ascent trajectory optimization for an aerospace vehicle is presented.

Lu, Ping↗