Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Angle of Attack”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1933

Wind-tunnel research comparing lateral control devices, particularly at high angles of attack V : spoilers and ailerons on rectangular wings

This report covers the fifth of a series of systematic investigations in which lateral control devices are compared with particular reference to their effectiveness at high angles of attack. The present report deals with tests of spoilers and ordinary ailerons on rectangular Clark y wing models. In an effort to obtain satisfactory control throughout the entire angle-of-attack range that can be maintained in flight, various spoilers were tested in combination with two sizes of previously tested ordinary ailerons - one of average proportions and the other short and wide. In addition, one large spoiler was tested alone. It was found that when ailerons and spoilers are used together the full effect of both is not obtained if the spoilers are located directly in front of the ailerons. With the proper combination of spoiler and aileron, however, it is possible to obtain satisfactory rolling control up to high angles of attack (15 degrees to 20 degrees), together with favorable yawing moments and small control forces. A moderate amount of rolling control with favorable yawing moments and small control forces was obtained with the large spoiler alone.

Weick, Fred E↗
NASA NTRS1955

Impingement of Water Droplets on NACA 65A004 Airfoil at 0 Deg Angle of Attack

The trajectories of water droplets in the air flowing past an NACA 6511004 airfoil at a n angle of attack of 0 deg were determined. The amount of water in droplet form impinging on the airfoil , the area of droplet impingement, and the rate of droplet impingement per unit area on the airfoil surface were calculated from the trajectories and presented t o cover a large range of flight and atmospheric conditions. These impingement characteristics are compared briefly with those previously reported for the same airfoil at angles of attack of 4 deg and 8 deg.

Brun, Rinaldo J.↗
NASA NTRS1977

Low Reynolds number flow past a blunt axisymmetric body at angle of attack

Low Reynolds number flow of an ideal gas over a blunt axisymmetric body of large half-angle at small angles of attack is investigated, for the case of laminar hypersonic flow. Time-varying viscous shock layer equations describing the flowfield are obtained from the full Navier-Stokes system by keeping terms to second order in the inverse square root of Re in both viscous and inviscid regions; the equations are valid for moderate to high Re. Drag, skin friction, and heating rates were obtained at small (or zero) angles of attack. Conditions experienced by planetary entry probes during the high-altitude (early) legs of an atmospheric entry trajectory are pertinent to the problem.

Kumar, A.↗
NASA NTRS1981

Hinged strakes for enhanced maneuverability at high angles of attack

A controllable-strake concept for alleviating the adverse effects of strake vortex breakdown and asymmetry on the longitudinal and lateral aerodynamics of strake-wing configurations at high angles of attack is presented. The concept aims to control the strake load independently of angle of attack and sideslip by varying the anhedral angle of strakes hinged along the root chord. The strakes may be deflected in a symmetrical or nonsymmetrical mode for a variety of control functions. Results are presented of an exploratory wind-tunnel investigation to evaluate the potential of the hinged-strake concept for enhancing the three-axis controllability in post-stall flight.

Rao, D. M.↗
NASA NTRS1980

Mathematical modeling of the aerodynamics of high-angle-of-attack maneuvers

This paper is a review of the current state of aerodynamic mathematical modeling for aircraft motions at high angles of attack. The mathematical model serves to define a set of characteristic motions from whose known aerodynamic responses the aerodynamic response to an arbitrary high angle-of-attack flight maneuver can be predicted. Means are explored of obtaining stability parameter information in terms of the characteristic motions, whether by wind-tunnel experiments, computational methods, or by parameter-identification methods applied to flight-test data. A rationale is presented for selecting and verifying the aerodynamic mathematical model at the lowest necessary level of complexity. Experimental results describing the wing-rock phenomenon are shown to be accommodated within the most recent mathematical model by admitting the existence of aerodynamic hysteresis in the steady-state variation of the rolling moment with roll angle. Interpretation of the experimental results in terms of bifurcation theory reveals the general conditions under which aerodynamic hysteresis must exist.

Schiff, L. B.↗
NASA NTRS1975

Calculation of the flow on a blunted cone at high angle of attack

A new technique for calculating the entire flow-field on spherically blunted circular cones at high angles of attack and high Reynolds numbers is described. The calculations are based on a single-layer system of three-dimensional parabolic equations which are approximations to the full steady Navier-Stokes equations. Initial conditions at the sphere-cone tangency plane are provided by using an inviscid time-dependent solution added to a viscous nonsimilar boundary layer solution. Calculated results are compared with experimental heat transfer and pressure data for a 15 deg half-angle cone with a 1-in. spherical nose at 15 deg angle of attack. The free-stream Mach number is 10.6, and the free-stream Reynolds number is 1,200,000 per foot. Excellent agreement between the calculated and experimental data for both pressure and heat transfer is obtained.

Lubard, S. C.↗
NASA NTRS1977

Aerodynamic characteristics at high angles of attack

An overview is presented of the aerodynamic inputs required for analysis of flight dynamics in the high-angle-of-attack regime wherein large-disturbance, nonlinear effects predominate. An outline of the presentation is presented. The discussion includes: (1) some important fundamental phenomena which determine to a large extent the aerodynamic characteristics of airplanes at high angles of attack; (2) static and dynamic aerodynamic characteristics near the stall; (3) aerodynamics of the spin; (4) test techniques used in stall/spin studies; (5) applications of aerodynamic data to problems in flight dynamics in the stall/spin area; and (6) the outlook for future research in the area.

Chambers, J. R.↗
NASA NTRS1978

Results of piloted simulator studies of fighter aircraft at high angles of attack

The experience gained at the NASA Langley Research Center during the application of simulator techniques to high angle of attack flight conditions for several current fighters is discussed. The discussion includes (1) the simulator hardware, (2) requirements for static and dynamic aerodynamic data inputs, (3) evaluation procedures, (4) correlation with flight, and (5) the effects of dynamic stability parameters. Results obtained with the simulator technique have correlated well with flight test experience, resulting in early identification of potential problems, identification of critical flight conditions, and solutions to various deficiencies in stability and control characteristics. Dynamic stability parameters, results indicate that certain parameters can have a large influence on the flying qualities and tactical effectiveness of fighters at high angles of attack.

Chambers, J. R.↗
NASA NTRS1990

Experimental investigation of a new device to control the asymmetric flowfield on forebodies at large angles of attack

An exploratory experimental investigation of a new device to control the asymmetric flowfield on forebodies at large angles of attack has been conducted. The device is a rotatable forebody tip, which varies in cross section from circular at its base to elliptic at its tip. The device itself extends over a small portion of the aircraft or missile forebody. The device provides two important improvements. First, it replaced the normally random behavior of the nose side force as a function of nose tip orientation with a predictable and generally sinusoidal distribution and, second, the device showed promise for use as part of a vehicle control system, to be deflected in a prescribed manner to provide additional directional control for the vehicle. The device was tested on a cone/cylinder model having a 10 deg semiapex angle and on a 3.0 caliber tangent ogive model, each with a base diameter of 3.5 in, for angles of attack from 30 to 60 deg. Data were taken from 3 circumferential rows of pressure taps on each model at a Reynolds number of 84,000 based on cylinder diameter and by a helium-bubble flow visualization technique at a Reynolds number of 24,000.

Moskovitz, Cary A.↗
NASA NTRS1989

Low-speed wind tunnel performance of high-speed counterrotation propellers at angle-of-attack

The low-speed aerodynamic performance characteristics of two advanced counterrotation pusher-propeller configurations with cruise design Mach numbers of 0.72 were investigated in the NASA Lewis 9- by 15-Foot Low-Speed Wind Tunnel. The tests were conducted at Mach number 0.20, which is representative of the aircraft take/off/landing flight regime. The investigation determined the effect of nonuniform inflow on the propeller performance characteristics for several blade angle settings and a range of rotational speeds. The inflow was varied by yawing the propeller mode to angle-of-attack by as much as plus or minus 16 degrees and by installing on the counterrotation propeller test rig near the propeller rotors a model simulator of an aircraft engine support pylon and fuselage. The results of the investigation indicated that the low-speed performance of the counterrotation propeller configurations near the take-off target operating points were reasonable and were fairly insensitive to changes in model angle-of-attack without the aircraft pylon/fuselage simulators installed on the propeller test rig. When the aircraft pylon/fuselage simulators were installed, small changes in propeller performance were seen at zero angle-of-attack, but fairly large changes in total power coefficient and very large changes of aft-to-forward-rotor torque ratio were produced when the propeller model was taken to angle-of-attack. The propeller net efficiency, though, was fairly insensitive to any changes in the propeller flowfield conditions near the take-off target operating points.

Hughes, Christopher E.↗
NASA NTRS1999

Flight-Determined, Subsonic, Lateral-Directional Stability and Control Derivatives of the Thrust-Vectoring F-18 High Angle of Attack Research Vehicle (HARV), and Comparisons to the Basic F-18 and Predicted Derivatives

The subsonic, lateral-directional, stability and control derivatives of the thrust-vectoring F-1 8 High Angle of Attack Research Vehicle (HARV) are extracted from flight data using a maximum likelihood parameter identification technique. State noise is accounted for in the identification formulation and is used to model the uncommanded forcing functions caused by unsteady aerodynamics. Preprogrammed maneuvers provided independent control surface inputs, eliminating problems of identifiability related to correlations between the aircraft controls and states. The HARV derivatives are plotted as functions of angles of attack between 10deg and 70deg and compared to flight estimates from the basic F-18 aircraft and to predictions from ground and wind tunnel tests. Unlike maneuvers of the basic F-18 aircraft, the HARV maneuvers were very precise and repeatable, resulting in tightly clustered estimates with small uncertainty levels. Significant differences were found between flight and prediction; however, some of these differences may be attributed to differences in the range of sideslip or input amplitude over which a given derivative was evaluated, and to differences between the HARV external configuration and that of the basic F-18 aircraft, upon which most of the prediction was based. Some HARV derivative fairings have been adjusted using basic F-18 derivatives (with low uncertainties) to help account for differences in variable ranges and the lack of HARV maneuvers at certain angles of attack.

Iliff, Kenneth W.↗
NASA NTRS2009

Angle of Attack Modulation for Mars Entry Terminal State Optimization

From the perspective of atmospheric entry, descent, and landing (EDL), one of the most foreboding destinations in the solar system is Mars due in part to its exceedingly thin atmosphere. To benchmark best possible scenarios for evaluation of potential Mars EDL system designs, a study is conducted to optimize the entry-to-terminal-state portion of EDL for a variety of entry velocities and vehicle masses, focusing on the identification of potential benefits of enabling angle of attack modulation. The terminal state is envisioned as one appropriate for the initiation of terminal descent via parachute or other means. A particle swarm optimizer varies entry flight path angle, ten bank profile points, and ten angle of attack profile points to find maximum-final-altitude trajectories for a 10 30 m ellipsled at 180 different combinations of values for entry mass, entry velocity, terminal Mach number, and minimum allowable altitude. Parametric plots of maximum achievable altitude are shown, as are examples of optimized trajectories. It is shown that appreciable terminal state altitude gains (2.5-4.0 km) over pure bank angle control may be possible if angle of attack modulation is enabled for Mars entry vehicles. Gains of this magnitude could prove to be enabling for missions requiring high-altitude landing sites. Conclusions are also drawn regarding trends in the bank and angle of attack profiles that produce the optimal trajectories in this study, and directions for future work are identified.

Lafleur, Jarret M.↗
NASA NTRS1988

Eigenstructure assignment for a thrust-vectored high angle-of-attack aircraft

Eigenstructure assignment is utilized to design flight control laws for a thrust-vectored aircraft at several different angles of attack. An interesting characteristic of the aircraft model is that the control distribution matrix is rank-deficient. Also, the effectiveness of the control inputs varies with the angle of attack. A pseudocontrol strategy is used to reduce the control space to two dimensions. After the eigenstructure assignment design is complete, the controller is mapped back to the original five-dimensional control space. The designs are shown to exhibit acceptable multivariable stability margins at the aircraft inputs.

Sobel, Kenneth M.↗
NASA NTRS1989

Low-speed wind tunnel performance of high-speed counterrotation propellers at angle-of-attack

The low-speed aerodynamic performance characteristics of two advanced counterrotation pusher-propeller configurations with cruise design Mach numbers of 0.72 were investigated in the NASA Lewis 9- by 15-Foot Low-Speed Wind Tunnel. The tests were conducted at Mach number 0.20, which is representative of the aircraft take-off/landing flight regime. The investigation determined the effect of nonuniform inflow on the propeller performance characteristics for several blade angle settings and a range of rotational speeds. The inflow was varied by yawing the propeller model to angle-of-attack by as much as plus or minus 16 degrees and by installing on the counterrotation propeller test rig near the propeller rotors a model simulator of an aircraft engine support pylon and fuselage. The results of the investigation indicated that the low-speed performance of the counterrotation propeller configurations near the take-off target operating points were reasonable and were fairly insensitive to changes in model angle-of-attack without the aircraft pylon/fuselage simulators installed on the propeller test rig. When the aircraft pylon/fuselage simulators were installed, small changes in propeller performance were seen at zero angle-of-attack, but fairly large changes in total power coefficient and very large changes of aft-to-forward-rotor torque ratio were produced when the propeller model was taken to angle-of-attack. The propeller net efficiency, though, was fairly insensitive to any changes in the propeller flowfield conditions near the take-off target operating points.

Hughes, Christopher E.↗
NASA NTRS1954

Airfoil section characteristics at high angles of attack

Information from the literature and from recent investigations is used herein to summarize briefly the effects of airfoil section parameters and flow variables on the aerodynamic characteristics of two-dimensional symmetrical airfoils at high angles of attack. The results presented indicate that airfoil thickness ratio, Reynolds number, Mach number, and surface roughness can all have an important effect on the maximum lift coefficient. The effect of surface roughness seems to be particularly important. Not only can surface roughness cause large decreases in maximum lift coefficient, but also the magnitudes of the effects of Reynolds number, Mach number, and airfoil thickness ratio are much reduced by surface roughness. Beyond the stall, changes in section thickness ratio appear to have little effect on the aerodynamic characteristics of airfoil sections. An investigation of one section through an angle-of-attack range of from 0° to 360° shows that the drag coefficient reaches a value of 2 at an angle of attack of 90°.

Laurence K Loftin, Jr↗
NASA NTRS2004

Effects of Angle of Attack and Velocity on Trailing Edge Noise

Trailing edge (TE) noise measurements for a NACA 63-215 airfoil model are presented, providing benchmark experimental data for a cambered airfoil. The effects of flow Mach number and angle of attack of the airfoil model with different TE bluntnesses are shown. Far-field noise spectra and directivity are obtained using a directional microphone array. Standard and diagonal removal beamforming techniques are evaluated employing tailored weighting functions for quantitatively accounting for the distributed line character of TE noise. Diagonal removal processing is used for the primary database as it successfully removes noise contaminates. Some TE noise predictions are reported to help interpret the data, with respect to flow speed, angle of attack, and TE bluntness on spectral shape and peak levels. Important findings include the validation of a TE noise directivity function for different airfoil angles of attack and the demonstration of the importance of the directivity function s convective amplification terms.

Hutcheson, Florence V.↗