SEARCH · Engineering Papers

Results for “yield strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Explosive Welding of Aluminum, Titanium and Zirconium to Copper Sheet Metal

The main material properties affecting the explosive weldability of a certain metal combination are the yield strength, the ductility, the density and the sonic velocity of the two metals. Successful welding of the metal combination depends mainly on the correct choice of the explosive welding parameters; i.e., the stand off distance, the weight of the explosive charge relative to the weight of the flyer plate and the detonation velocity of the explosive. Based on the measured and the handbook values of the properties of interest, the explosive welding parameters were calculated and the arrangements for the explosive welding of the Al alloy 6061-T6, titanium and zirconium to OFHC copper were determined. The relatively small sheet metal thickness (1/8") and the fact that the thickness of the explosive layer must exceed a certain minimum value were considered during the determination of the explosive welding conditions. The results of the metallographic investigations and the measurements of the shear strength at the interface demonstrate the usefulness of these calculations to minimize the number of experimental trials.

Hegazy, A. A.↗

NASA NTRS1985

Fabrication and evaluation of superplastically formed/weld-brazed corrugated compression panels with beaded webs

A study was made to investigate the feasibility of superplastically forming corrugated panels with beaded webs and to demonstrate the structural integrity of these panels by testing. The test panels in the study consist of superplastically formed titanium alloy Ti-6Al-4V half-hat elements that are joined by weld-brazing to titanium alloy Ti-6Al-4V caps to form either single-corrugation compression panels or multiple-corrugation compression panels. Stretching and subsequent thinning of the titanium sheet during superplastic forming is reduced by approximately 35 percent with a shallow half-hat die concept instead of a deep die concept and results in a more uniform thickness across the beaded webs. The complete panels are tested in end compression at room temperature and the results compared with analysis. The heavily loaded panels failed at loads approaching the yield strength of the titanium material. At maximum load, the caps wrinkled locally accompanied with separation of the weld-braze joint in the wrinkle. None of the panels tested, however, failed catastrophically in the weld-braze joint. Experimental test results are in good agreement with structural analysis of the panels.

Royster, D. M.↗

NASA NTRS1986

Simplified cyclic structural analyses of SSME turbine blades

Anisotropic high-temperature alloys are used to meet the safety and durability requirements of turbine blades for high-pressure turbopumps in reusable space propulsion systems. The applicability to anisotropic components of a simplified inelastic structural analysis procedure developed at the NASA Lewis Research Center is assessed. The procedure uses as input the history of the total strain at the critical crack initiation location computed from elastic finite-element analyses. Cyclic heat transfer and structural analyses are performed for the first stage high-pressure fuel turbopump blade of the space shuttle main engine. The blade alloy is directionally solidified MAR-M 246 (nickel base). The analyses are based on a typical test stand engine cycle. Stress-strain histories for the airfoil critical location are computed using both the MARC nonlinear finite-element computer code and the simplified procedure. Additional cases are analyzed in which the material yield strength is arbitrarily reduced to increase the plastic strains and, therefore, the severity of the problem. Good agreement is shown between the predicted stress-strain solutions from the two methods. The simplified analysis uses about 0.02 percent (5 percent with the required elastic finite-element analyses) of the CPU time used by the nonlinear finite element analysis.

Kaufman, A.↗

NASA NTRS1985

Nondestructive techniques for characterizing mechanical properties of structural materials: An overview

An overview of nondestructive evaluation (NDE) is presented to indicate the availability and application potentials of techniques for quantitative characterization of the mechanical properties of structural materials. The purpose is to review NDE techniques that go beyond the usual emphasis on flaw detection and characterization. Discussed are current and emerging NDE techniques that can verify and monitor entrinsic properties (e.g., tensile, shear, and yield strengths; fracture toughness, hardness, ductility; elastic moduli) and underlying microstructural and morphological factors. Most of the techniques described are, at present, neither widely applied nor widely accepted in commerce and industry because they are still emerging from the laboratory. The limitations of the techniques may be overcome by advances in applications research and instrumentation technology and perhaps by accommodations for their use in the design of structural parts.

Vary, A.↗

NASA NTRS1986

Effect of additional heat treatment of 2024-T3 on the growth of fatigue crack in air and in vacuum

In order to determine the influence of ductility on the fatigue crack growth rate of aluminum alloys, fatigue tests were carried out on central notched specimens of 2024-T3 and 2024-T8 sheet material. The 2024-T8 material was obtained by an additional heat treatment applied on 2024-T3 (18 hours at 192 C), which increased the static yield strength from 43.6 to 48.9 kgf/sq mm. A change in the ultimate strength was not observed. Fatigue tests were carried out on both materials in humid air and in high vacuum. According to a new crack propagation model, crack extension is supported to be caused by a slip-related process and debonding triggered by the environment. This model predicts an effect of the ductility on the crack growth rate which should be smaller in vacuum than in humid air; however, this was not confirmed. In humid air the crack-growth rate in 2024-T8 was about 2 times faster than in 2024-T3, while in vacuum the ratio was about 2.5. Crack closure measurements gave no indications that crack closure played a significant role in both materials. Some speculative explanations are briefly discussed.

Louwaard, E. P.↗

NASA NTRS1985

A precise measurement of the cosmic microwave background temperature from optical observations of interstellar CN

Very precise observations (with S/N greater than 2000) of the 3874-angstrom band of interstellar CN toward zeta Per and omicron Per are presented. In the zeta Oph, zeta Per, and omicron Per lines of sight, the saturation-corrected CN line strengths yield respective excitation temperatures of 2.72 plus or minus 0.05 K, 2.76 plus or minus 0.05 K, and 2.78 plus or minus 0.07 K for the J = 0-1 rotational transition at 2.64 mm. By confirming the blackbody character of the cosmic microwave background spectrum at wavelengths near the peak of its flux, the simplest explanation of the background as primeval fireball radiation from a hot bang is reinforced.

Meyer, D. M.↗

NASA NTRS1985

Estimates of rheologic properties for flows on the Martian volcano Ascraeus Mons

Morphological measurements on six well-defined volcanic flows near the summit of the Martian volcano Ascraeus Mons were used to calculate the yield strength and viscosity of the lavas. The results are similar to values obtained for flows on other Martian and terrestrial shield volcanoes. Calculated viscosities are generally higher than measured viscosities for basaltic lavas but considerably smaller than rhyolite or dacite viscosities. The estimated rheologic properties of the Martian flows are most consistent with basaltic or basaltic andesite lavas, but some individual flows could consist of more evolved lavas.

Zimbelman, J. R.↗

NASA NTRS1985

Nondestructive determination of mechanical properties

The sensitivity of the velocity of ultrasonic waves to the elasticity of the materials (acousto-elastic constant - AEC) as controlled by the microstructure of the materials was examined experimentally. Rolled-plate specimens of five different Al alloys were subjected to tensile tests while being monitored for the velocity change of a 10 MHz longitudinal wave as a function of the applied tensile stress. The acoustic propagation velocity was measured perpendicularly to the stress. Determinations were made of the yield strength and the hardnesses of the specimens. Samples of the plate materials examined microscopically to characterize the solid phases. The AECs varied linearly with the percentage of solid solution phase of the alloys. The trend for strain-hardened samples was, however, opposite from that in the precipitation-hardened alloys. The results underscore the necessity of considering the microstructural dependencies of the AECs when using ultrasonic NDE methods, and also opened the potential of determining some mechanical properties with NDE techniques.

Schneider, E.↗

NASA NTRS1986

Nondestructive techniques for characterizing mechanical properties of structural materials - An overview

An overview of nondestructive evaluation (NDE) is presented to indicate the availability and application potentials of techniques for quantitative characterization of the mechanical properties of structural materials. The purpose is to review NDE techniques that go beyond the usual emphasis on flow detection and characterization. Discussed are current and emerging NDE techniques that can verify and monitor entrinsic properties (e.g., tensile, shear, and yield strengths; fracture toughness, hardness, ductility; elastic moduli) and underlying microstructural and morphological factors. Most of the techniques described are, at present, neither widely applied nor widely accepted in commerce and industry because they are still emerging from the laboratory. The limitations of the techniques may be overcome by advances in applications research and instrumentation technology and perhaps by accommodations for their use in the design of structural parts.

Vary, A.↗

NASA NTRS1986

Orientation and temperature dependence of some mechanical properties of the single-crystal nickel-base superalloy Rene N4. I - Tensile behavior

Single crystal specimens of a nickel-base superalloy with axes near 001, 011, and -112 were tested in tension at room temperature, 760, and 980 C. The alloy Rene N-4, was developed for gas turbine engine blades and has the nominal composition 3.7 Al, 4.2 Ti, 4 Ta, 0.5 Nb, 6 W, 1.5 Mo, 9 Cr, 7.5 Co, balance Ni, (all in weight percent). Analysis of slip band traces, specimen axis rotation, and dislocation Burgers vectors showed that at 760 and 980 C primary cube slip supplanted normal octahedral slip for the -112 line-oriented specimens. The other two orientations, which have lower resolved shear stresses on the cube system, exhibited octahedral slip at all three temperatures. The critical resolved shear stress is considerably greater on the cube system than on the octahedral system at room temperature. However, at 760 and 980 C the critical resolved shear stresses on the two systems are about the same. While the room temperature and 980 C yield strengths for the two orientations exhibiting octahedral slip could be rationalized on the basis of resolved shear stress, those at 760 C could not. Such violations of Schmid's law have previously been observed in other superalloys and single phase gamma-prime.

Miner, R. V.↗

NASA NTRS1986

High temperature monotonic and cyclic deformation in a directionally solidified nickel-base superalloy

Directionally solidified (DS) MAR-M246+Hf was tested in tension and fatigue, at temperatures from 20 C to 1093 C. Tests were performed on (001) oriented specimens at strain rates of 50 % and 0.5 % per minute. In tension, the yield strength was constant up to 704 C, above which the strength dropped off rapidly. A strong dependence of strength on strain rate was seen at the higher temperatures. The deformation mode was observed to change from heterogeneous to homogeneous with increasing temperature. Low Cycle Fatigue tests were done using a fully reversed waveform and total strain control. For a given plastic strain range, lives increased with increasing temperature. For a given temperature strain rate had a strong effect on life. At 704 C, decreasing strain rates decreased life, while at the higher temperatures, decreasing strain rates increased life, for a given plastic strain range. These results could be explained through considerations of the deformation modes and stress levels. At the higher temperatures, marked coarsening caused beneficial stress reductions, but oxidation limited the life. The longitudinal grain boundaries were found to influence slip behavior. The degree of secondary slip adjacent to the boundaries was found to be related to the degree of misorientation between the grains.

Huron, Eric S.↗

NASA NTRS1987

Material characterization of superplastically formed titanium (Ti-6Al-2Sn-4Zr-2Mo) sheet

The aerospace industry has focused considerable interest on the near-alpha titanium alloy Ti-6Al-2Sn-4Zr-2Mo (Ti-6242) because of both its high-temperature properties and its superplastic forming (SPF) capabilities. This paper describes current research to characterize selected mechanical properties of Ti-6242 sheet in the SPF-strained condition, both with and without heat treatment, and compares the results with those obtained on as-received material. Tensile and creep tests were conducted, and metallographic analysis was performed to show the effect of 100 to 700 percent SPF strain on titanium properties. Analysis shows that as a result of SPF processing, both tensile and yield strengths, as well as elongation, are moderately reduced. Creep tests at 800 F and 1000 F show that the SPF processed material displays superior creep resistance compared with the as-received material. A post-SPF duplex-anneal heat treatment had no beneficial effect on tensile and creep properties.

Ossa, William A.↗

NASA NTRS1987

Thermo-elasto-viscoplastic analysis of problems in extension and shear

The problems of extension and shear behavior of structural elements made of carbon steel and subjected to large thermomechanical loads are investigated. The analysis is based on nonlinear geometric and constitutive relations, and is expressed in a rate form. The material constitutive equations are capable of reproducing all nonisothermal, elasto-viscoplastic characteristics. The results of the test problems show that: (1) the formulation can accommodate very large strains and rotations; (2) the model incorporates the simplification associated with rate-insensitive elastic response without losing the ability to model a rate-temperature dependent yield strength and plasticity; and (3) the formulation does not display oscillatory behavior in the stresses for the simple shear problem.

Riff, R.↗

NASA NTRS1986

Terrace width variations in complex lunar craters

The widths of terrace structures in complex craters on the moon are compared to existing theoretical models of their origin. Terrace widths in an individual crater increase monotonically outward toward the crater rim. Similarly, the width W of the terraces lying closest to the rim of a crater of diameter D increases monotonically, obeying a least-squares power-law relation WS (km) = 0.09D exp 0.87 km). A simple model of slumping that ignores inertial forces and assumes a constant bedrock yield strength is in good agreement with the observations.

Pearce, Steven J.↗

NASA NTRS1987

The friction and wear of TPS fibers

The sliding friction behavior of single filaments of SiO2, SiC, and an aluminoborosilicate has been determined. These fibers are used in thermal protection systems (TPS) and are subject to damage during weaving and aero-maneuvering. All fibers exhibited stick-slip friction indicating the successive formation and rupture of strong junctions between the contacting filaments. The static frictional resistance of the sized SiC filament was 4X greater than for the same filament after heat cleaning. This result suggests that the sizing is an organic polymer with a high shear yield strength. Heat cleaning exposes the SiC surface and/or leaves an inorganic residue so that the adhesional contact between filaments has a low fracture energy and frictional sliding occurs by brittle fracture. The frictional resistances of the sized and heat cleaned SiO2 and glass filaments were all comparable to that of the heat cleaned SiC. It would appear that the sizings as well as the heat cleaned surfaces of the silica and glass have low fracture energies so that the sliding resistance is determined by brittle fracture.

Bascom, W. D.↗

NASA NTRS1987

Coatings for high-temperature bearings and seals

Criteria are discussed for predicting the probable lubricating ability of candidate solid materials from a consideration of their basic chemical and physical properties. The properties considered to be important in the model are thermochemical potential, adhesion, low hardness, plasticity, yield strength in shear, and brittle-to-ductile transition characteristics. A review of the selection and tribological testing of materials, which were selected for use in self-lubricating composite coatings by employing this model, is given. Two series of plasma-sprayed coatings with good tribological properties over a wide temperature spectrum are described. The PS 100 series of coatings contain oxidatively stable solid lubricants in a nichrome matrix. The PS 200 series contains the same solid lubricants in a very wear resistant metal-bonded chromium carbide matrix. Examples are given of applications of these coatings in high speed shaft seals, sliding contact bearings, and Stirling engine cylinder liners.

Sliney, Harold E.↗

NASA NTRS1987

The microstructure and tensile properties of extruded melt-spun ribbons of iron-rich B2 FeAl

The microstructure of extruded rods of iron-rich FeAl(B2-structure), as characterized by TEM, SEM, optical microscopy and x-ray diffractometry, consisted of elongated grains with a 111-line fibre texture containing a high dislocation density. Numerous oxide particles were found, mostly in lines which reflected the matrix flow during extrusion. In addition, some large inclusions were present. Tensile testing of annealed, relatively dislocation-free specimens as a function of increasing temperature found increasing ductility up to 900K, above which a ductility drop occurred accompanied by a change in fracture mode, from transgranular cleavage to intergranular fracture. The yield strength, which was independent of temperature up to 800K (at about 500MPa), also decreased rapidly as diffusion became more important. The predominant slip vector changed from 111-line to 100-line around 700K.

Baker, I.↗

NASA NTRS1987

Room temperature tensile ductility in powder processed B2 FeAl alloys

It has been shown that it is possible to obtain significant room temperature tensile ductility in FeAl alloys using iron-rich deviations from stoichiometry. A comparison of the room temperature tensile and compressive behaviors of Fe-50 at. pct Al and Fe-40 at. pct Al shows that FeAl is brittle at higher Al contents because it fractures along grain boundaries before general yielding. Lower aluminum contents reduce the yield stress substantially and hence some ductility is observed before fracture. Addition of boron results in measurable improvements in ductility of Fe-40 at. pct Al and is accompanied by an increase in transgranular tearing on the fracture surface, suggesting a grain boundary strengthening mechanism. Increasing the cooling rate following annealing at 1273 K results in a large increase in the yield strength and a corresponding decrease in ductility.

Crimp, M. A.↗