SEARCH · Engineering Papers

Results for “vortex methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS1980

An experimental investigation of three dimensional low speed minimum interference wind tunnel for high lift wings

As a means to achieve a minimum interference correction wind tunnel, a partially actively controlled test section was experimentally examined. A jet flapped wing with 0.91 m (36 in) span and R = 4.05 was used as a model to create moderately high lift coefficients. The partially controlled test section was simulated using an insert, a rectangular box 0.96 x 1.44 m (3.14 x 4.71 ft) open on both ends in the direction of the tunnel air flow, placed in the University of Washington Aeronautical Laboratories (UWAL) 2.44 x 3.66 m (8 x 12 ft) wind tunnel. A tail located three chords behind the wing was used to measure the downwash at the tail region. The experimental data indicates that, within the range of momentum coefficient examined, it appears to be unnecessary to actively control all four sides of the test section walls in order to achieve the near interference free flow field environment in a small wind tunnel. The remaining wall interference can be satisfactorily corrected by the vortex lattice method.

Shindo, S.↗

NASA NTRS1981

Effect of sweep angles on aerodynamic performance of double arrow wing - An analytical study

Hybrid wing planforms are studied for adoption on supersonic transport and fighter aircraft. The free vortex sheet method is used to determine effects of the leading-edge sweep angles on the aerodynamic performance of a double arrow wing with a strake. Results show lift and drag increase with the increase of the inboard and outboard leading-edge sweep angles. However, the lift-to-drag ratio is little influenced by the changes in these sweep angles. Spanwise surface pressure distributions on the aft region are influenced by the inboard sweep angle while the outboard sweep angle has no effect on these pressures. Finally, the experimental data and predicted results are compared to show good agreement.

Reddy, C. S.↗

NASA NTRS1983

The evaluation of the rolling moments induced by wraparound fins

A possible reason is suggested for the induced rolling moments occurring on wraparound-fin configurations in subsonic flight at zero angle of attack. The subsonic potential flow over the configuration at zero incidence is solved numerically. The body is simulated by a distribution of sources along its axis, and the fins are described by a vortex-lattice method. It is shown that rolling moments can be induced on the antisymmetric fins by the radial flow generated at the base of the configuration, either over the converging separated wake, or over the diverging plume of a rocket motor.

Seginer, A.↗

NASA NTRS1983

Aerodynamic optimization, comparison, and trim design of canard and conventional high performance general aviation configurations

A design study has been conducted to optimize trim cruise flight of high performance general aviation canard aircraft which achieve minimum drag. In order to investigate the advantages and disadvantages of canard configured aircraft, corresponding conventional tail-aft 'baseline' aircraft were designed and used for comparison. Two-dimensional predictions were obtained by coupling inviscid results from a vortex panel multi-element program to a momentum integral boundary layer analysis. Using the results of the two-dimensional vortex panel analysis, a vortex lattice method was employed to predict the finite wing results. The analysis utilized a turbulent airfoil and a natural laminar airfoil which are two NASA state-of-the-art airfoil sections. The canard aircraft designs give quantitative results of wing and canard loadings, wing-to-canard moment arm ratios, and aspect ratio effects for trim cruise flight for a wide range of wing-to-canard area ratios. Both canard and baseline aircraft achieved a 25 to 30 percent improvement in performance over typical current technology aircraft, but high canard loading necessary for trim resulted in slightly poorer performance of the canard aircraft as compared to the baseline designs.

Keith, M. W.↗

NASA NTRS1983

The evaluation of the rolling moments induced by wraparound fins

Seginer, A.↗

NASA NTRS1984

An analytical design procedure for the determination of effective leading edge extensions on thick delta wings

An analytical design procedure for leading edge extensions (LEE) was developed for thick delta wings. This LEE device is designed to be mounted to a wing along the pseudo-stagnation stream surface associated with the attached flow design lift coefficient of greater than zero. The intended purpose of this device is to improve the aerodynamic performance of high subsonic and low supersonic aircraft at incidences above that of attached flow design lift coefficient, by using a vortex system emanating along the leading edges of the device. The low pressure associated with these vortices would act on the LEE upper surface and the forward facing area at the wing leading edges, providing an additional lift and effective leading edge thrust recovery. The first application of this technique was to a thick, round edged, twisted and cambered wing of approximately triangular planform having a sweep of 58 deg and aspect ratio of 2.30. The panel aerodynamics and vortex lattice method with suction analogy computer codes were employed to determine the pseudo-stagnation stream surface and an optimized LEE planform shape.

Farhad Ghaffari↗

NASA NTRS1984

Aerodynamic canard/wing parametric analysis for general aviation applications

Vortex panel and vortex lattice methods have been utilized in an analytic study to determine the two- and three-dimensional aerodynamic behavior of canard and wing configurations. The purpose was to generate data useful for the design of general aviation canard aircraft. Essentially no two-dimensional coupling was encountered and the vertical distance between the lifting surfaces was found to be the main contributor to interference effects of the three-dimensional analysis. All canard configurations were less efficient than a forward wing with an aft horizontal tail, but were less sensitive to off-optimum division of total lift between the two surfaces, such that trim drag could be less for canard configurations. For designing a general aviation canard aircraft, results point toward large horizontal and vertical distance between the canard and wing, a large wing-to-canard area ratio, and with the canard at a low incidence angle relative to the wing.

Keith, M. W.↗

NASA NTRS1985

Dynamic ground effects on a two-dimensional flat plate

The effect of time-variant vortex shedding is simulated by a sequence of discrete vortices convecting downstream in the wake of a two-dimensional flat plate whose lifting condition is modeled by means of the quasi-vortex lattice method. The boundary condition of this problem is specified in such a way that the tangency condition on the surface of the flat plate is satisfied; the boundary condition also takes into account the effect of airfoil motion relative to the ground. Significant lift changes are shown to occur, due to the dynamic ground effect, that are crucial in aircraft takeoff and landing transitions.

Chen, Y.-S.↗

NASA NTRS1984

Modeling techniques for transonic airfoils

In the present comparative study of computer codes for the modeling of two-dimensional, single element airfoil sections for various section geometry classes, two of the codes use vortex singularities methods to obtain the potential flow solution while the remainder solve the full inviscid potential flow equations by means of finite differencing techniques that allow results to be obtained for transonic flow about an airfoil which includes weak shocks. Computational results are presented for a symmetrical airfoil section, a conventional section, and a supercritical one. Icing condition applications of the models are noted. The model codes' range of applicability and agreement with each other and experimental results, as well as their computer run times and memory requirements, are noted.

Petrie, S. L.↗

NASA NTRS1986

Euler equation analysis of the initial roll-up of aircraft wakes

A new approach has been developed to study the initial roll-up of aircraft wakes. This approach is based on the solution of the three-dimensional Euler equations subject to inflow and initial conditions predicted by a vortex-lattice method. This procedure allows for the solution of this complex problem without any empirical inputs. However, valid solutions are limited to those flowfields generated by wings which are free of flow separation. Results are presented for four configurations: a rectangular wing with part span flap, a rectangular wing, a typical transport-type configuration and a fighter configuration. In addition, an assessment of an 'unsteady 2-D analogy' was undertaken using the 2-D time accurate Euler equation solutions in crossflow planes. In general, predictions from the 2-D unsteady analogy coincided with the 3-D results which were found to be in good agreement with available experimental data.

Mitcheltree, R. A.↗

NASA NTRS1986

Investigation of chord ratio, stagger, decalage angle, and flap angle for dual wing configurations

Aerodynamical closely coupled dual wing configurations of unequal chords are investigated for medium speed general aviation applications. Vortex panel and momentum boundary layer analysis are utilized for the two-dimensional predictions. A multi-surface vortex lattice method is used for the three-dimensional predictions. In the process of searching for the highest lift to drag ratio upper airfoil to lower airfoil chord ratios, both greater than and less than one, are investigated in terms of stagger, decalage angle, and gap. With the optimum chord ratio, at the optimum stagger and gap, proper spanwise decalage distribution is shown to yield the lowest two dimensional drag results. Various wing taper ratios and wing twists are investigated to increase wing efficiency. Comparisons are made between optimized dual and optimized single wing configurations both with the same fuselage, stabilator surfaces, engines, payload, and fuel. The dual wing configuration is shown to have significantly less drag and hence longer range than the conventional single wing configuration.

Selberg, B. P.↗

NASA NTRS1986

Unsteady forces on counter-rotating propeller blades

Unsteady forces experienced by counter-rotating propeller blades are examined in this paper. A fully coupled vortex lattice model of counter-rotation is used to obtain a quasi-steady solution to the propeller loadings, and an unsteady Sears (1941) analysis provides an estimate of the unsteady loads from the quasi-steady results. The vortex lattice method predicts the overall performance of counter-rotation well, based on comparisons of measured and predicted results. The effects of propeller spacing and blade number on the unsteady loadings are investigated. The peak-to-peak variation about the mean of the unsteady loads on the rear propeller varied from 9 percent for a 2 x 2 counter-rotation system to 2 percent for an 8 x 8 system.

Lesieutre, D. J.↗

NASA NTRS1989

Transonic Unsteady Aerodynamics and Aeroelasticity 1987, part 2

This two part document contains copies of the text and figures for the papers presented at the symposium held at NASA Langley on 20 to 22 May, 1987. The papers are grouped in five subject areas. The areas covered by this part includes the following: Methods for vortex and viscous flows; Aeroelastic applications, and Experimental results and cascade flows.

Bland, Samuel R.↗

NASA NTRS1989

Control of separated flow past a cylinder using tangential wall jet blowing

A theoretical analysis is conducted to study the effect of a tangential wall jet on the control of two dimensional separated flow past a circular cylinder. For a tangential wall jet, the mathematical model derived previously is used and the vortex cloud method is adopted for the calculation of the external flow field. For certain limiting cases, the governing equations are simplified and closed forms of solutions for the wall jet parameters can be obtained. It is observed that the wall jet is very efficient in reducing drag by delaying the separation point in the range of small blowing strength. The suction force induced by the wall jet is negligible to the drag due to the external stream. However this suction increases the drag when the blowing strength is large.

Oh, Sejong↗

NASA NTRS1990

Discrete-vortex model for the symmetric-vortex flow on cones

A relatively simple but accurate potential flow model was developed for studying the symmetric vortex flow on cones. The model is a modified version of the model first developed by Bryson, in which discrete vortices and straight-line feeding sheets were used to represent the flow field. It differs, however, in the zero-force condition used to position the vortices and determine their circulation strengths. The Bryson model imposed the condition that the net force on the feeding sheets and discrete vortices must be zero. The proposed model satisfies this zero-force condition by having the vortices move as free vortices, at a velocity equal to at the local crossflow velocity at their centers. When the free-vortex assumption is made, a solution is obtained in the form of two nonlinear algebraic equations that relate the vortex center coordinates and vortex strengths to the cone angle and angle of attack. The vortex center locations calculated using the model are in good agreement with experimental values. The cone normal forces as well as center locations are in good agreement with the vortex cloud method of calculating symmetric flow fields.

Gainer, Thomas G.↗

NASA NTRS1989

Accumulated span loadings of an arrow wing having vortex flow

The vortex flow over an arrow wing is theoretically investigated using the free-vortex-sheet method. The sectional lift coefficient and accumulated span loadings, which are important in determining the root bending moment, are calculated. The longitudinal stability variation is also estimated.

Reddy, C. Subba↗

NASA NTRS1991

Aerodynamic parameter studies and sensitivity analysis for rotor blades in axial flight

The analytical capability is offered for aerodynamic parametric studies and sensitivity analyses of rotary wings in axial flight by using a 3-D undistorted wake model in curved lifting line theory. The governing equations are solved by both the Multhopp Interpolation technique and the Vortex Lattice method. The singularity from the bound vortices is eliminated through the Hadamard's finite part concept. Good numerical agreement between both analytical methods and finite differences methods are found. Parametric studies were made to assess the effects of several shape variables on aerodynamic loads. It is found, e.g., that a rotor blade with out-of-plane and inplane curvature can theoretically increase lift in the inboard and outboard regions respectively without introducing an additional induced drag.

Chiu, Y. Danny↗

NASA NTRS1992

Vortex-Blob Simulation Of Two-Dimensional Flows

Software package includes two programs: KPD12 and KPD12P. Both programs use vortex-blob method to simulate flow around solid bodies. KPD12 treats unbounded domain, while KPD12P treats domain having periodicity in one direction. Main advantage, ability to handle situations involving arbitrary shapes, including multiple bodies. User supplies only points on solid boundaries; no grid. Source code in Cray FORTRAN.

Spalart, Philippe↗