Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “vinyl”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Hydrogen bonds enhanced composite polymer electrolyte for high-voltage cathode of solid-state lithium battery

Polymer electrolyte is one of the important components for developing advanced solid-state lithium batteries (SSLBs). However, the narrow electrochemical stability window restricts the practical application with high-voltage cathodes. In this study, a series of composite solid electrolytes (CSEs), possessing both wide electrochemical stability window (up to 5.0 V vs. Li + /Li) and high ionic conductivity (over 1.35×10 -3 S/cm at 25 °C), were reported by integrating SiO 2 nanoparticles into poly(vinyl ethylene carbonate) polymer electrolyte. The enhanced anti-oxidation performances are mainly caused and confirmed by the local intermolecular interactions of hydrogen bonds in CSE. Based on this CSE, the SSLBs with LiCoO 2 cathode present good cycle stability at high voltage, and the capacity retention with 4.5 V cut-off voltage is about 94% after 200 cycles. This work not only proves the importance of intermolecular interactions in CSE, but also provides an effective method for achieving high-energy SSLBs with enhanced interface compatibility between polymer electrolyte and highvoltage cathodes

25 ENERGY STORAGE↗
DOE OSTI2022

Probing O 2 dependence of hydroperoxy-butyl reactions via isomer-resolved speciation

Degenerate chain-branching mechanisms of n-alkanes are centered on the formation of hydroperoxy-alkyl radicals ($\dot{Q}$OOH), formed via $\dot{R}$ + O 2 reactions, and the ensuing competition between unimolecular decomposition and second-O 2 -addition. Quantitative measurements of partially oxidized intermediates formed via reactions of $\dot{Q}$OOH provide critical constraints that are required for accurate modeling of combustion chemistry. To examine the influence of temperature and oxygen concentration on intermediates from unimolecular decomposition of $\dot{Q}$OOH, isomer-resolved speciation measurements were conducted on n-butane oxidation at 835 Torr in a jet-stirred reactor (JSR) from 500 – 900 K. Resulting from negative-temperature coefficient behavior, cyclic ether formation peaked at two temperatures, 650 K and 800 K, which were selected for separate experiments to quantify the O 2 -dependence of species profiles using O 2 concentrations of 4.2 · 10 17 – 1.1 · 10 19 molecules cm –3 . Utilizing vacuum-ultraviolet absorption spectroscopy and electron-impact mass spectrometry, cyclic ether isomers were quantified separately, including explicit resolution of cis– and trans– isomers of 2,3-dimethyloxirane. Stereoisomers of 2-butene were also quantified explicitly. For all cyclic ethers, a common trend in O 2 -dependence emerged: species concentrations reach a maximum near 3.0 · 10 18 molecules cm –3 (equivalence ratio of 0.5). Although quantitative disparities are evident, chemical kinetics modeling qualitatively reproduces the O 2 dependence of species at 650 K. However, at 800 K, weak dependence on O 2 is predicted, which is in contrast with the measurements. Two carbonyls, diacetyl and methyl vinyl ketone, were also quantified and follow similar dependence on [O 2 ] and temperature as the cyclic ethers, which indicates some fraction forms via $\dot{Q}$OOH-mediated reactions. The discrepancies between the measured and model-predicted species profiles indicate that sub-mechanisms for important intermediates may require additional elementary reactions, including stereochemical-specific reactions, to improve the fidelity of n-alkane combustion modeling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Styrene Thermal Decomposition and Its Reaction with Acetylene under Shock Tube Pyrolysis Conditions: an Experimental and Kinetic Modeling Study

Styrene is an important compound for polymer production and a key intermediate in gas-phase kinetics of polycyclic aromatic hydrocarbons (PAHs). For the first time, the pyrolysis of styrene with and without the presence of acetylene is investigated in a single-pulse shock tube coupled to gas chromatography and mass spectrometry. For each reaction system, quantitative speciation profiles are probed within the temperature range of 1100-1730 K, nominal pressure of 20 bar, and reaction duration of similar to 4 ms. A kinetic model is built to simulate the results. The model explains how styrene is consumed under high-pressure pyrolytic conditions, how the secondary chemistry of intermediate products affect subsequent PAH formation, and how acetylene addition alters the reaction pathways. Throughout the temperature range, styrene breakdown is dominated by the bimolecular interaction between styrene and hydrogen atom, which produces benzene+vinyl or phenyl and ethylene through the stabilization of 2-phenylethyl and its subsequent dissociation. As a result, large amounts of phenyl accumulate, which react with styrene to form C14H12 species while simultaneously releasing H atoms through addition/elimination reactions. The reactivity of fuel consumption is preserved by the regeneration of H atoms as chain carriers. Several C14H10 compounds are formed as a result of the following breakdown of the C14H12 isomers, particularly stilbene, 1,1-diphenyl ethylene, and 9-methyl-9H-fluorene. The presence of acetylene as a co-reactant with styrene allows the Hydrogen-Abstraction-Acetylene-Addition (HACA) pathway to proceed from phenyl radical to enhance the production of phenylacetylene at very low temperatures and acenaphthylene. This hinders the formation of C14H12 isomers, exclusive products from pure styrene dissociation by competing with the styrene+phenyl routes.

Kinetic Modeling↗
DOE OSTI2023

Recycling of a post-industrial printed multilayer plastic film containing polyurethane inks by solvent-targeted recovery and precipitation

The recently reported Solvent-Targeted Recovery And Precipitation (STRAP) strategy is used to deconstruct multilayer plastic packaging films into their constituent resins by selective polymer dissolution. To broaden the applicability of STRAP, we demonstrate the process with a flexible post-industrial printed multilayer plastic film used for food packaging. The material was a reverse printed film composed of polyethylene (PE), ethylene vinyl alcohol (EVOH), polyethylene terephthalate (PET), and polyurethane (PU)-based inks. Removal of all colors was observed with biomass-derived gamma-valerolactone (GVL) and the recovered polymers possessed comparable properties to the corresponding virgin resins. A technoeconomic analysis indicates that this STRAP process could be economically feasible at a processing capacity of 6,000 tons per year. Furthermore, the production of plastic films with materials recovered by this STRAP process can have a lower climate change impact than the production of films from virgin polymers.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Delamination recycling of multilayer plastic films: Solvent-assisted separation pathways and recovery of solid polyolefins

Multilayer plastic films are excellent packaging materials due to the bound layers of multiple polymers, with each different polymer contributing to the film properties. Desirable properties lead to continuously growing demand for multilayer films. Multilayer plastic films are typically single-use and, as such, their increased production and disposal have led to waste management problems. Multilayer films are not currently recyclable primarily due to the multiple bound polymers. This work advances delamination as a recycling process to separate and sequester valuable polymers from multilayer films, facilitating the incorporation of these polymers into the circular economy. We effect delamination in a physical process that preserves targeted polymers as solid film, hence retaining their embodied energy. This work documents three different pathways of inducing delamination of multilayer films, with appropriate solvents disrupting adhesion between adjacent layers or dissolving a minor component of the film in less than an hour and at temperatures below 90°C, and where all initial polyethylene is maintained in its solid form throughout the process and is recovered at high purity. Solvent-based delamination is exemplified on commercial multilayer films with majority polyethylene (PE), and polyethylene terephthalate (PET) or ethylene vinyl alcohol copolymer (EVOH) or nylon also present. Solvent-based delamination is an energy-efficient and environmentally friendly recycling process that improves upon dissolution-precipitation recycling, since delamination involves very little dissolution and no precipitation, and is superior to pyrolysis which breaks down the polymers, while delamination keeps polymer chains intact. Furthermore, delamination recycling can contribute to the sustainable use of multilayer films as they continue to protect our food and medicine.

Chemical Recycling↗
DOE OSTI2023

Field retrieved photovoltaic backsheet survey from diverse climate zones: Analysis of degradation patterns and phenomena

Understanding the impact of climate stressors on photovoltaic (PV) backsheet degradation in real-use conditions is critical to improve the accelerated testing exposures, extend the backsheet lifetime, and increase the confidence in PV reliability. Here, in this work, a total of 33 PV module backsheets were retrieved from six climatic zones worldwide with 2 - 28 years of exposure. These modules included five types of backsheet air-side materials (or outer layer): poly(vinylidene fluoride) (PVDF), poly(tetrafluoroethylene-co-hexafluoropropylene-co-vinylidene fluoride) (THV), poly(vinyl fluoride) (PVF), poly(ethylene terephthalate) (PET), and polyamide (PA). Attenuated total reflection Fourier-transform infrared spectroscopy (ATR-FTIR) was used to identify air-side materials. The degradation induced color change, gloss loss, and chemical material changes analyzed using optical microscopy, differential scanning calorimetry (DSC), scanning electron microscopy (SEM), colorimetry (yellowness index (YI)), and gloss measurements. PVDF, THV, and PVF air-side layer backsheets, in particular PVF, had minimal degradation in the air-side layer appearance and chemical structures after exposure in different climatic zones. The PET air-side backsheets exhibited obvious color increase (22.55 YI units after about 9 years exposure) and the PA/PA/PA backsheets showed large gloss loss (up to 76.4 %) relative to the unexposed backsheets. Severe cracks between cells that penetrated through the entire thickness of backsheets are observed on PA/PA/PA backsheets after 4-6 years of exposure in 6 climatic zones. The current indoor exposure standards were not sufficient to identify this degradation type. However, fluoropolymer based PV backsheets showed lower levels of degradation predictors and increased climatic resistance. Specific samples (PVF) showed little change from baseline after 28 years of outdoor exposure.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2020

Characterizing photovoltaic backsheet adhesion degradation using the wedge and single cantilever beam tests, Part I: Field Modules

Photovoltaic backsheets are exposed to harsh outdoor weathering conditions throughout their service lives that can compromise their protective function, through adhesive debonding between their constituent layers and between the backsheet and the module. We report a large-scale study on adhesive degradation was conducted on 37 field-exposed modules, that spanned 19 different module manufacturers, that were deployed among six Köppen–Geiger climatic zones, and that were fielded between 0 and 28 years. Six outer layer polymer classes were identified among the backsheets: polyamide (PA), polyethylene terephthalate (PET), polyvinyl fluoride (PVF), polyvinylidene fluoride (PVDF), fluoroethylene vinyl ether copolymer (FEVE), and tetrafluoroethylene hexafluoropropylene vinylidene fluoride copolymer (THV). Two adhesion tests were used to measure the adhesive strength: the wedge test and the width-tapered single-cantilever beam (SCB) test. Adhesion energies were compared across exposure time and Köppen–Geiger climatic zone. Many of the PET-, PVF-, and PVDF-based backsheets experienced degradation of the adhesive layer between the backsheet outer and core layers. A consistent trend of decreasing adhesion energy with exposure time was observed in five out of the six backsheet types. Trends among adhesion energy and climatic zone, while expected, were not observed, possibly due to broad ranges in temperature, humidity, and precipitation defining Köppen–Geiger climatic zones. The cantilever beam measurements produced an upper cutoff of approximately 100 J/m 2 , above which no modules exhibited field delamination. The results are part of a two-part study quantifying adhesion in both field-weathered and indoor-exposed PV backsheets.

14 SOLAR ENERGY↗
DOE OSTI2021

Corrosion of novel reactive silver ink and commercial silver-based metallizations in diluted acetic acid

Silver-based metallizations in photovoltaic modules are susceptible to corrosion by acetic acid generated in ethylene vinyl acetate encapsulated modules, resulting in power losses over time. Here, three silver-based metallizations are exposed to diluted acetic acid, in concentrations representative of that found in field-exposed modules. Compositional, morphological, and structural changes of the metallizations are studied over 3000 h of exposure to diluted acetic acid using Raman spectroscopy mapping, X-ray diffraction, and scanning electron microscopy. The three metallizations studied are: 1) a commercial high-temperature fire-through Ag paste, commonly used for Si diffused junction solar cells; 2) a commercial low-temperature paste normally used for silicon heterojunction cells; and 3) a novel low-temperature reactive silver ink shown to be suitable for photovoltaic applications. We find distinct corrosion rates for the high-temperature silver paste and reactive silver ink in the presence of diluted acetic acid. However, the low-temperature silver paste appears to be more corrosion resistant, likely due to a polymer layer that protects the silver particles.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Understanding interfacial chemistry of positive bias high-voltage degradation in photovoltaic modules

Photovoltaic module degradation from a high system voltage is a prevalent degradation mode in the field, where the enabling degradation mechanisms are inherently dependent on the voltage bias polarity of the installed system. In this study, the effects of positive bias on module performance are confirmed and the underlying chemical degradation processes are more thoroughly investigated to reveal different degradation pathways from those previously reported in negative bias studies. When cells are under +1000 V stress, crystalline silicon mini-modules with poly(ethylene-co-vinyl acetate) (EVA) encapsulant demonstrated a significant photocurrent loss due to EVA discoloration and delamination from increased chemical reactivity at the front-side EVA/cell metallization interface. Brown discoloration of the EVA encapsulant near the cell gridlines is linked to an electrochemical reaction at the Ag gridlines under hot and humid conditions (85 °C, 85% relative humidity). Chemical compositional analysis using X-ray photoelectron spectroscopy (XPS) confirmed that the discoloration is attributed to the formation of silver sulfide (Ag 2 S) and/or silver oxide (Ag 2 O) species at the EVA/Ag gridline interface. The subsequent migration of Ag ions from the cell gridlines into the bulk of the EVA was evident from XPS depth profiling and optical microscopy. However, the Ag signal was not detected at the EVA/glass interface, inferring limited ionic transport through the nominally 0.45 mm thick encapsulant. For the samples studied herein, the sulfur is believed by the process of elimination to come from the ambient air, diffusing into the module through the permeable polymer backsheet.

14 SOLAR ENERGY↗
DOE OSTI2022

Impact of acetic acid exposure on metal contact degradation of different crystalline silicon solar cell technologies

Degradation due to acetic acid in photovoltaic (PV) modules has been a commonly observed phenomenon for both damp-heat exposure and outdoor operations. Acetic acid is a degradation byproduct of ethylene-vinyl acetate (EVA), a common module encapsulant. To address this issue, robust metallization pastes and cell technologies are being developed. However, it is important to assess how these technologies perform in an acetic acid environment and withstand degradation before they are implemented in the solar market. In this work, we investigate the impact of acetic acid exposure on four different cell groups: monofacial passivated emitter and rear contact (PERC) cells with advanced telluride-based front contact pastes, bifacial PERC cells with novel aluminum rear contact pastes, bifacial tunnel oxide passivated contacts (TOPCon) cells, and silicon heterojunction (SHJ) cells. These cells were exposed to acetic acid for different time increments. The recombination losses were characterized by Suns-VOC, and multi-variate regression analysis of intensity-dependent photoluminescence (PL) images with Griddler AI. Resistive losses were tracked with the transmission line method (TLM). Samples showing severe performance degradation were selected for further materials characterization to understand the root cause. Top-down and cross-sectional scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray photoelectron spectroscopy (XPS) were performed to investigate the change in materials properties. Our study shows that the front contacts of the bifacial TOPCon cells and monofacial PERC cells were significantly affected by acetic acid exposure. Here, the SHJ cells were found to be the most stable.

14 SOLAR ENERGY↗
DOE OSTI2023

PV encapsulant formulations and stress test conditions influence dominant degradation mechanisms

Polyethylene-based poly(ethylene-co-vinyl acetate) (EVA), polyolefin elastomer (POE), and thermoplastic polyolefin (TPO) are common polymer candidates for photovoltaic (PV) module encapsulants. The choice of encapsulant must be carefully considered in novel module designs, such as bifacial glass/glass laminates, to limit performance degradation through loss of optical transmittance, mechanical integrity, and corrosion - as well as potential-induced degradation. Encapsulant quality and resilience against environmental stressors are readily influenced by the additives in the encapsulant formulation. Here, we show that, the changes in optical transmittance after UV aging result from the discoloration caused by interactions between additives, and optical scattering from changes in the polymer crystal structure. We observed competing cross-linking and chain scission mechanisms, with their kinetics influenced by the presence of oxygen and elevated temperatures. Increasing chamber temperatures from 55 °C to 85 °C during the UV stress test amplified encapsulant discoloration and promoted polymer cross-linking, causing severe, irreversible damage that remains to be proven field relevant. Damp heat aging was found to be insufficient to produce significant encapsulant degradation; however, combining stress tests sequentially allowed detection of further degradation beyond the limitations of the damp heat test alone. Appropriate degradation screening methods are necessary to uncover potential encapsulant weaknesses.

14 SOLAR ENERGY↗
DOE OSTI2025

Critical role of polymer-ceramic ion exchange for high conductivity composite electrolytes

Polymer-ceramic composites offer a path to enhance the transport and mechanical properties of solid electrolytes. However, an in-depth understanding of the extent and role of ion transport along and across polymer-ceramic interfaces in these systems is lacking. We have recently shown that Li-conducting Li 0.11 Na 0.24 K 0.02 La 0.43 TiO 2.82 (LMTO) nanorods can be prepared by a molten flux method, and the addition of 30–50 weight (wt.)% LMTO to a bis[(trifluoromethyl)sulfonyl]imide-vinyl ethylene carbonate-based single-ion conducting (SIC) polymer electrolyte leads to a two-fold enhancement in Li-ion conductivity, from 1.4 to 3.0 × 10 −5 S/cm at 30 °C. In the present study, we use NMR methods to identify the Li-ion transport pathways and determine the timescale of chemical exchange between the SIC polymer and LMTO ceramic components. Tracer exchange NMR indicates preferential transport through the polymer or polymer-interfacial regions, and exchange spectroscopy (EXSY) and a new isotope exchange method reveal negligible Li exchange between the SIC polymer and LMTO ceramic up to several days. Here, LMTO nanorods act as a passive filler. Our results further highlight that significant (e.g., 10- or 100-fold) conductivity enhancements in composite electrolytes can only be achieved 1) with ionically-conductive fillers, and 2) when both the ceramic and polymer components actively participate in long-range transport. For this, fast interfacial ion exchange is needed. In conclusion, this leads us to introduce a critical interfacial ion exchange time to evaluate whether a filler actively contributes to conduction in a composite electrolyte, and screen for promising polymer-ceramic pairings to accelerate the development of high conductivity solid electrolytes.

Battery, Solid electrolyte↗
DOE OSTI2020

Iodoindenes: Synthesis and application to cross-coupling

An expeditious synthesis of 5-, 6-, and 7-iodoindenes from the corresponding aminoindan-1-ones in more than 70% yield employing readily available precursors and ubiquitous reagents is reported. The 4-iodoindene has been prepared analogously in 40% overall yield. A three-step sequence involves diazotization-iodination of aminoindan-1-one followed by the reduction and dehydration. The iodoindenes serve as effective substrates for the regioselective Stille coupling with vinyl stannanes but isomeric mixtures are produced during Sonogashira coupling with alkynes in the presence of triethylamine.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Design of robust and versatile hydrocarbon-based single-ion-conducting polymer electrolytes

Hydrocarbon-based polymers offer several advantages, including lower environmental impacts, cost effectiveness, and the ability to finely tune properties. Here, we have developed trifluoromethanesulfonimide (TFSI)-functionalized poly(norbornene) (PNB) polymers utilizing a specifically designed oxa-Michael addition of a vinyl TFSI anion to an alcohol. Our results reveal that PNB-TFSI derivatives exhibit superior thermal stability and mechanical robustness compared with Nafion. The optimized PNB-TFSI-H-48 polymer (IEC 1.86 mmol/g) exhibits equivalent performance to Nafion as an anode ionomer in a proton exchange membrane fuel cell. Exchanging the counter ion to Li + enables PNB-TFSI to be used for Li-ion battery applications. Propylene carbonate plasticized PNB-TFSI derivatives achieve an Li-ion conductivity of over 10 −5 S/cm at 30°C. This Li polymer electrolyte exhibits excellent electrochemical stability (5 V vs. Li + /Li) and good cycling in a Li symmetric cell. These results highlight the potential and rational design of PNB-TFSI polymers for next-generation energy storage and conversion technologies.

08 HYDROGEN↗
DOE OSTI2025

Late Metal Sandwich Catalysts for Olefin Polymerization

Polyolefins are by far the most ubiquitous industrially produced polymers and are primarily produced by early transition metal catalysts. These catalysts are not functional group tolerant, and copolymerization of ethylene and polar vinyl monomers is quite challenging. Furthermore, early metal catalysts convert ethylene to linear polyethylene, and introduction of branches requires addition of comonomers. In this Account, we describe our efforts in designing and implementing new Pd(II) and Ni(II) olefin polymerization catalysts based on mechanistic understanding of the chain growth process. Here, the original hindered nickel- and palladium-aryl-substituted diimine complexes were discovered in 1995. The key to the success of these now “classic” systems in generating high polymers rather than dimers or oligomers was realizing that incorporation of ortho-disubstituted aryl groups partially blocks the axial sites of the metal and thus retards the rate of chain transfer relative to propagation. Two key features of these late metal catalysts distinguish them from early metal complexes. First, they tolerate certain functional groups, which allows copolymerization of olefins with polar comonomers. Second, they can form a branched polymer from ethylene without the need to add α-olefin comonomers. Importantly, for nickel catalysts, branching levels can be modulated by changing reaction conditions, such as temperature and monomer pressure.

Catalysts↗
DOE OSTI2021

Resolving Chemical and Spatial Heterogeneities at Complex Electrochemical Interfaces in Li-Ion Batteries

The high specific capacities of Ni-rich transition metal oxides have garnered immense interest for improving the energy density of Li-ion batteries (LIBs). Despite the potential of these materials, Ni-rich cathodes suffer from interfacial instabilities that lead to crystallographic rearrangement of the active material surface as well as the formation of a cathode electrolyte interphase (CEI) layer on the composite during electrochemical cycling. While changes in crystallographic structure can be detected with diffraction-based methods, probing the chemistry of the disordered, heterogeneous CEI layer is challenging. In this work, we use a combination of ex situ solid-state nuclear magnetic resonance (SSNMR) spectroscopy and X-ray photoemission electron microscopy (XPEEM) to provide chemical and spatial information, on the nanometer length scale, on the CEI deposited on LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) composite cathode films. XPEEM elemental maps offer insight into the lateral arrangement of the electrolyte decomposition products that comprise the CEI and paramagnetic interactions (assessed with electron paramagnetic resonance (EPR) and relaxation measurements) in 13 C SSNMR provide information on the radial arrangement of the CEI from the NMC811 particles outward. Using this approach, here we find that LiF, Li 2 CO 3 , and carboxy-containing structures are directly appended to NMC811 active particles, whereas soluble species detected during in situ 1 H and 19 F solution NMR experiments (e.g., alkyl carbonates, HF, and vinyl compounds) are randomly deposited on the composite surface. We show that the combined approach of ex situ SSNMR and XPEEM, in conjunction with in situ solution NMR, allows spatially-resolved, molecular-level characterization of paramagnetic surfaces and new insights into electrolyte oxidation mechanisms in porous electrode films.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Expanding the Design Space of Polymer–Metal Organic Framework (MOF) Gels by Understanding Polymer–MOF Interactions

The fabrication of polymer-MOF composite gels holds great potential to provide emergent properties for drug delivery, environmental remediation, and catalysis. To leverage the full potential of these composites, we investigated how the presence and chemistry of polymers impact MOF formation within the composites and, in turn, how MOFs impact polymer gelation. We show that polymers with a high density of strongly metal-binding carboxylic acids inhibit MOF formation; however, reducing the density of carboxylic acids or substituting them with weaker metal-binding hydroxyl groups permits both MOF formation and gelation within composites. Preparing composites with poly(ethylene glycol) (PEG), which does not bind MOF zirconium (Zr)-oxo clusters, and observing gelation suggests that MOFs can entrap polymer chains to create cross-links in addition to cross-linking them through polymer-Zr-oxo interactions. Both simulations and experiments show composite hydrogels formed with poly(vinyl alcohol) (PVA) to be more stable than those made with PEG, which can reptate through MOF pores upon heating. We demonstrate the generalizability of this composite formation process across different Zr-based MOFs (UiO-66, NU-901, UiO-67, and MOF-525) and by spin-coating gels into conformable films. PVA-UiO-66 composite hydrogels demonstrated high sorption and sustained release of methylene blue relative to the polymer alone (3× loading, 28× slower release), and PVA-MOF-525 composite hydrogels capably sorb the therapeutic peptide Angiotensin 1–7. By understanding the influence of polymer-MOF interactions on the structure and properties of composite gels, this work informs and expands the design space of this emerging class of materials.

36 MATERIALS SCIENCE↗