Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “tool size”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Low-Temperature Friction-Stir Welding of 2024 Aluminum

Solid state friction-stir welding (FSW) has been demonstrated to involve dynamic recrystallization producing ultra-fine, equiaxed grain structures to facilitate superplastic deformation as the welding or joining mechanism. However, the average residual, equiaxed, grain size in the weld zone has ranged from roughly 0.5 micron to slightly more than 10 micron, and the larger weld zone grain sizes have been characterized as residual or static grain growth as a consequence of the temperatures in the weld zone (where center-line temperatures in the FSW of 6061 Al have been shown to be as high as 480C or -0.8 T(sub M) where T(sub M) is the absolute melting temperature)). In addition, the average residual weld zone grain size has been observed to increase near the top of the weld, and to decrease with distance on either side of the weld-zone centerline, an d this corresponds roughly to temperature variations within the weld zone. The residual grain size also generally decreases with decreasing FSW tool rotation speed. These observations are consistent with the general rules for recrystallization where the recrystallized grain size decreases with increasing strain (or deformation) at constant strain rate, or with increasing strain-rate, or with increasing strain rate at constant strain; especially at lower ambient temperatures, (or annealing temperatures). Since the recrystallization temperature also decreases with increasing strain rate, the FSW process is somewhat complicated because the ambient temperature, the frictional heating fraction, and the adiabatic heating fraction )proportional to the product of strain and strain-rate) will all influence both the recrystallization and growth within the FSW zone. Significantly reducing the ambient temperature of the base metal or work pieces to be welded would be expected to reduce the residual weld-zone grain size. The practical consequences of this temperature reduction would be the achievement of low temperature welding. This study compares the residual grain sizes and microstructures in 2024 Al friction-stir welded at room temperature (about 30C and low temperature (-30C).

Benavides, S.↗

Development of an Hourly Optimization Tool for Renewable Energy Systems

An hourly optimization tool is developed to select and size renewable energy (RE) systems to meet the energy needs for various federal facilities. The optimization is based on life cost analysis of various RE technologies including wind and PV systems. The developed hourly optimization tool is used to evaluate the cost-effectiveness of RE technologies using complex energy and demand charges such time-of-use (TOU) rates. The paper compares results obtained using hourly analysis instead of annual based calculations to optimize the sizing of RE systems for residential, commercial, and industrial facilities in three representative US climates.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Using dorsal surface for individual identification of dairy calves through 3D deep learning algorithms

Advances in machine learning techniques have allowed the development of computer vision systems (CVS) that can accurately predict several phenotypes of interest for livestock operations. In this context, 3D images taken from a top-down view are particularly useful for estimating body condition score, growth development, and body biometrics in cattle. Frequently, such CVS rely on identification (ID) systems, such as electronic tags, as a way to match animal ID and the predicted phenotype. However, the same 3D images used to predict body weight and other animal biometrics could be adopted for animal recognition as well. Such alternative would optimize CVS to recognize animal ID and monitor growth development simultaneously while leveraging the same hardware infrastructure. Furthermore, this strategy could be used to recognize animals with similar color patterns. Nonetheless, growing animals are continuously changing body shape, which could limit its use as an invariant feature for pattern recognition. Thus, the objectives of this study were: (1) to compare algorithms for different 3D object representations to identify individual animals; and (2) to evaluate how short-term changes in body shape due to animal growth affect the predictive performance of these algorithms. For objective 1, the algorithms were trained (n = 4,558) and tested (n = 1,139) using images from 38 Holstein calves. For objective 2, we designed three different experiments using images (n = 2,347) from five Holstein calves taken over six weeks during their growing period, always training and testing on different weeks. Each experiment evaluated how changing a different parameter of the image capturing procedure affected the predictive ability of the trained algorithms. In the first experiment, we varied the total number of images per animal in the training set; in the second experiment, we varied the number of weeks while keeping a fixed number of images in the training set; and in the third experiment, we skipped weeks between images in the training and test sets. The F 1 score for objective (1) was up to 0.804 when testing with the last frames of each video, and up to 0.959 when using random frames for testing. For objective (2), the F 1 score was up to 0.947 for the first experiment when using 130 images per animal; up to 0.979 for the second experiment when using all five weeks; and up to 0.917 when not skipping weeks between training and testing. In conclusion, these results show that deep learning algorithms can be used to identify individual animals through their dorsal area 3D surfaces, and, from our experiments using calves in their growing period, that they are robust enough to account for changes in body shape and size, making them a promising tool for animal recognition during growth.

3D neural networks↗

Rotational Dynamics and Transition Mechanisms of Surface-Adsorbed Proteins

Assembly of biomolecules at solid-water interfaces requires molecules to traverse complex orientation-dependent energy landscapes through processes that are poorly understood, largely due to the dearth of in-situ single molecule measurements and statistical analyses of the rotational dynamics that define directional selection. Emerging capabilities in high-speed atomic force microscopy and machine learning have allowed us to directly determine the orientational energy landscape and observe and quantify the rotational dynamics for protein nanorods on the surface of muscovite mica under a variety of conditions. Comparisons with kinetic Monte Carlo simulations show that the transition rates between adjacent orientation-specific energetic minima can largely be understood through traditional models of in-plane Brownian rotation across a biased energy landscape, with resulting transition rates that are exponential in the energy-barriers between states. However, transitions between more distant angular states are decoupled from barrier height, with jump-size distributions showing a power-law decay that is characteristic of a non-classical Levy-flight random walk, indicating that large jumps are enabled by alternative modes of motion via activated states. The findings provide new insights into the dynamics of biomolecules at solid-liquid interfaces that lead to self-assembly, epitaxial matching and other orientationally anisotropic outcomes and define a general procedure for exploring such dynamics with implications for hybrid biomolecular-inorganic materials design.

Orientational energy landscapes, Rotational dynami↗

Toward Exascale: Overview of Large Eddy Simulations and Direct Numerical Simulations of Nuclear Reactor Flows with the Spectral Element Method in Nek5000

At the beginning of the last decade, Petascale supercomputers (i.e., computers capable of more than 1 petaFLOP) emerged. Now, at the dawn of exascale supercomputing, we provide a review of recent landmark simulations of portions of reactor components with turbulence-resolving techniques that this computational power has made possible. In fact, these simulations have provided invaluable insight into flow dynamics, which is difficult or often impossible to obtain with experiments alone. We focus on simulations performed with the spectral element method, as this method has emerged as a powerful tool to deliver massively parallel calculations at high fidelity by using large eddy simulation or direct numerical simulation. We also limit this paper to constant-property incompressible flow of a Newtonian fluid in the absence of other body or external forces, although the method is by no means limited to this class of flows. We briefly review the fundamentals of the method and the reasons it is compelling for the simulation of nuclear engineering flows. We review in detail a series of Petascale simulations, including the simulations of helical coil steam generators, fuel assemblies, and pebble beds. Even with Petascale computing, however, limitations for nuclear modeling and simulation tools remain. In particular, the size and scope of turbulence-resolving simulations are still limited by computing power and resolution requirements, which scale with the Reynolds number. In the final part of this paper, we discuss the future of the field, including recent advancements in emerging architectures such as GPUbased supercomputers, which are expected to power the next generation of high-performance computers.

computational fluid dynamics↗

Phase Stability in Nanocrystals: A Predictive Diagram for Yttria–Zirconia

Predicting the polymorphic stability of nanocrystals entails taking into account the thermodynamic effects from solid–vapor interfaces. With recent advances in microcalorimetry, it is finally possible to obtain reliable surface energy data which allow building of predictive diagrams, such as the usual phase diagrams for bulk crystals, for nanocrystals. Yttria doped zirconia (YZ) is currently utilized in a variety of applications; making it one of the most studied oxide systems to date. However, the polymorphism of nanocrystalline YZ (nYZ) is much less understood as compared to its bulk counterpart, and the stability conditions of cubic, tetragonal, monoclinic, and amorphous polymorphs at the nanoscale is so far only empirically defined. In this work, we present a new predictive nanoscale phase diagram for nYZ using unprecedented data on surface energies and bulk enthalpies acquired by microcalorimetry. The phase diagram shows the stable zirconia polymorph as a function of the composition and size. This is a useful tool and an important and novel advancement to relatively untouched bulk phase diagrams, which holds the key for reliable materials' design.

Drazin, John W.↗

Electrode Mesoscale as a Collection of Particles: Coupled Electrochemical and Mechanical Analysis of NMC Cathodes

Battery electrodes are composed of polydisperse particles and a porous, composite binder domain. These materials are arranged into a complex mesostructure whose morphology impacts both electrochemical performance and mechanical response. We present image-based, particle-resolved, mesoscale finite element model simulations of coupled electrochemical-mechanical performance on a representative NMC electrode domain. Beyond predicting macroscale quantities such as half-cell voltage and evolving electrical conductivity, studying behaviors on a per-particle and per-surface basis enables performance and material design insights previously unachievable. Voltage losses are primarily attributable to a complex interplay between interfacial charge transfer kinetics, lithium diffusion, and, locally, electrical conductivity. Mesoscale heterogeneities arise from particle polydispersity and lead to material underutilization at high current densities. Particle-particle contacts, however, reduce heterogeneities by enabling lithium diffusion between connected particle groups. While the porous composite binder domain (CBD) may have slower ionic transport and less available area for electrochemical reactions, its high electrical conductivity makes it the preferred reaction site late in electrode discharge. Mesoscale results are favorably compared to both experimental data and macrohomogeneous models. This work enables improvements in materials design by providing a tool for optimization of particle sizes, CBD morphology, and manufacturing conditions.

42 ENGINEERING↗

SBIR PHASE I FINAL REPORT: Adoption of High Performance Computational (HPC) Modeling Software for Widespread Use in the Manufacture of Welded Structures

Many US manufacturing companies have moved fabrication and production facilities off shore because of cheaper labor costs. A key aspect in bringing these jobs back to the US is the use of technology to render US-made fabrications more efficient overall with higher quality. A new initiative of the current administration has the goal of enhancing competitiveness to retain manufacturing jobs in the US. One significant competitive advantage that has emerged in the US over the last two decades is the use of virtual design for fabrication of large structures in the light and heavy materials industries. Industries that have used virtual design and analysis tools have reduced material parts size, developed environmentally-friendly fabrication processes, improved product quality and performance, and reduced manufacturing costs. Indeed, Caterpillar Inc. (CAT), one of the partners in this effort, continues to have a large fabrication presence in the US because of the use of weld fabrication modeling to optimize fabrications by controlling weld residual stresses and distortions and improving fatigue, corrosion, and fracture performance. This report describes Engineering Mechanics Corporation of Columbus (Emc2's) DOE SBIR Phase I results which extended an existing, state-of-the-art software code, VFT, currently used to design and model large welded structures prior to fabrication - to a broader range of products with widespread applications for small and medium-sized enterprises (SMEs). VFT helps control distortion, can minimize and/or control residual stresses, control welding microstructure, and pre-determine welding parameters such as weld-sequencing, pre-bending, thermal-tensioning, etc. VFT uses material properties, consumable properties, etc. as inputs. Through VFT, manufacturing companies can avoid costly design changes after fabrication. This leads to the concept of joint design/fabrication where these important disciplines are intimately linked to minimize fabrication costs. VFT currently is tied to a commercial solver which makes it prohibitively expensive for use by SMEs, as there is a significant licensing cost for the solver - over and above for the relatively minimal cost for VFT. Emc2 developed this software code over a number of years in close cooperation with CAT (Peoria, IL), who currently uses this code exclusively for worldwide fabrication, product design and development activities. The use of VFT has allowed CAT to move directly from design to product fabrication and helped eliminate (to a large extent) new product prototyping and subsequent testing. Additionally, CAT has been able to eliminate/reduce costly one-of-a-kind appliances used to reduce distortion effects due to fabrication. In this context, SMEs can realize the same kind of improved product quality and reduced cost through adoption of the adapted version of VFT for design and subsequent manufacture of new products. Emc2's DOE SBIR Phase I effort successfully adapted VFT so that SMEs have access to this sophisticated and proven methodology that is quick, accurate and cost effective and available on-demand to address weld-simulation and fabrication problems prior to manufacture. The open source code, WARP3D, a high performance finite element code mainly used in fracture and damage assessment of structures, was modified so that computational weld problems can be solved efficiently on multiple processors and threads with VFT. The thermal solver for VFT, based on a series of closed form solution approximations, was enhanced for solution on multiple processors greatly increasing overall speed. In addition, the graphical user interface (GUI) has been tailored to integrate these solutions with WARP3D. The GUI is used to define all the weld pass descriptions, number of passes, material properties, consumable properties, weld speed, etc. for the structure to be modeled. The GUI was improved to make it user-friendly for engineers that are not experts in finite element modeling. Finally, a plan for porting VFT onto the Ohio Supercomputer Center (OSC) through its hosted Manufacturing and Polymer Portal has been developed. This access route will permit SMEs to perform weld modeling to improve their competitiveness at a reasonable cost. All of these improvements are detailed in this repo

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Customer Agreement Considerations for Micro-Grids in Sub-Saharan Africa

Micro-grid deployment at a large scale will be necessary for achieving ambitious national and international electrification goals and reaching communities for whom grid extension is prohibitively expensive. The micro-grid industry is growing to fill this need, but barriers remain to reaching scale with sustainable, bankable business models. An important step along the way to industry maturation is creating customer agreements that serve as a foundation for a healthy, long-term relationship between developers, operators, and the communities their micro-grids serve. In addition to directly setting clear expectations with customers, a strong customer agreement can be a valuable tool for prospective funders, system sizing discussions, and customer retention. This report covers considerations for customer agreement design and content, and is intended to serve as a resource for micro-grid developers seeking to develop or re-design customer agreements to support growth and help achieve scale.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Portable power tool machines weld joints in field

Portable routing machine for cutting precise weld joints required by nonstandard pipe sections used in the field for transfer of cryogenic fluids. This tool is adaptable for various sizes of pipes and has a selection of router bits for different joint configurations.

Spier, R. A.↗

Numerical Control Machine Data Manual

Numerical Control Machine Data Manual provides programmers with specific information for various types and sizes of numerical control machine tools and auxiliary equipment.

Mackey, R. T., Sr.↗

Automatic differentiation as a tool in engineering design

Automatic Differentiation (AD) is a tool that systematically implements the chain rule of differentiation to obtain the derivatives of functions calculated by computer programs. AD is assessed as a tool for engineering design. The forward and reverse modes of AD, their computing requirements, as well as approaches to implementing AD are discussed. The application of two different tools to two medium-size structural analysis problems to generate sensitivity information typically necessary in an optimization or design situation is also discussed. The observation is made that AD is to be preferred to finite differencing in most cases, as long as sufficient computer storage is available; in some instances, AD may be the alternative to consider in lieu of analytical sensitivity analysis.

Barthelemy, Jean-Francois↗

Automatic Differentiation as a tool in engineering design

Automatic Differentiation (AD) is a tool that systematically implements the chain rule of differentiation to obtain the derivatives of functions calculated by computer programs. In this paper, it is assessed as a tool for engineering design. The paper discusses the forward and reverse modes of AD, their computing requirements, and approaches to implementing AD. It continues with application to two different tools to two medium-size structural analysis problems to generate sensitivity information typically necessary in an optimization or design situation. The paper concludes with the observation that AD is to be preferred to finite differencing in most cases, as long as sufficient computer storage is available.

Barthelemy, Jean-Francois M.↗

The mass storage testing laboratory at GSFC

Industry-wide benchmarks exist for measuring the performance of processors (SPECmarks), and of database systems (Transaction Processing Council). Despite storage having become the dominant item in computing and IT (Information Technology) budgets, no such common benchmark is available in the mass storage field. Vendors and consultants provide services and tools for capacity planning and sizing, but these do not account for the complete set of metrics needed in today's archives. The availability of automated tape libraries, high-capacity RAID systems, and high- bandwidth interconnectivity between processor and peripherals has led to demands for services which traditional file systems cannot provide. File Storage and Management Systems (FSMS), which began to be marketed in the late 80's, have helped to some extent with large tape libraries, but their use has introduced additional parameters affecting performance. The aim of the Mass Storage Test Laboratory (MSTL) at Goddard Space Flight Center is to develop a test suite that includes not only a comprehensive check list to document a mass storage environment but also benchmark code. Benchmark code is being tested which will provide measurements for both baseline systems, i.e. applications interacting with peripherals through the operating system services, and for combinations involving an FSMS. The benchmarks are written in C, and are easily portable. They are initially being aimed at the UNIX Open Systems world. Measurements are being made using a Sun Ultra 170 Sparc with 256MB memory running Solaris 2.5.1 with the following configuration: 4mm tape stacker on SCSI 2 Fast/Wide; 4GB disk device on SCSI 2 Fast/Wide; and Sony Petaserve on Fast/Wide differential SCSI 2.

Venkataraman, Ravi↗

New Approaches to HSCT Multidisciplinary Design and Optimization

New approaches to MDO have been developed and demonstrated during this project on a particularly challenging aeronautics problem- HSCT Aeroelastic Wing Design. To tackle this problem required the integration of resources and collaboration from three Georgia Tech laboratories: ASDL, SDL, and PPRL, along with close coordination and participation from industry. Its success can also be contributed to the close interaction and involvement of fellows from the NASA Multidisciplinary Analysis and Optimization (MAO) program, which was going on in parallel, and provided additional resources to work the very complex, multidisciplinary problem, along with the methods being developed. The development of the Integrated Design Engineering Simulator (IDES) and its initial demonstration is a necessary first step in transitioning the methods and tools developed to larger industrial sized problems of interest. It also provides a framework for the implementation and demonstration of the methodology. Attachment: Appendix A - List of publications. Appendix B - Year 1 report. Appendix C - Year 2 report. Appendix D - Year 3 report. Appendix E - accompanying CDROM.

Schrage, Daniel P.↗

Satellite Systems Design/Simulation Environment: A Systems Approach to Pre-Phase A Design

A toolset for the rapid development of small satellite systems has been created. The objective of this tool is to support the definition of spacecraft mission concepts to satisfy a given set of mission and instrument requirements. The objective of this report is to provide an introduction to understanding and using the SMALLSAT Model. SMALLSAT is a computer-aided Phase A design and technology evaluation tool for small satellites. SMALLSAT enables satellite designers, mission planners, and technology program managers to observe the likely consequences of their decisions in terms of satellite configuration, non-recurring and recurring cost, and mission life cycle costs and availability statistics. It was developed by Princeton Synergetic, Inc. and User Systems, Inc. as a revision of the previous TECHSAT Phase A design tool, which modeled medium-sized Earth observation satellites. Both TECHSAT and SMALLSAT were developed for NASA.

Ferebee, Melvin J., Jr.↗

Current status of research and development program for characterizing fuel debris at Fukushima Daiichi NPS by JAEA

Japan Government and TEPCO submitted a research road map for decommissioning Fukushima Daiichi Nuclear Power Plant. Two projects about debris are in progress: 'Assessment of simulated fuel debris characteristics' and 'Development of technologies for the processing of fuel debris'. The major results concerning the first project are the following 4 points. First, it was suggested that typical phase of oxide of fuel debris is (U,Zr)O{sub 2} and that of metal is Fe{sub 2}(Zr,U) by thermodynamic calculation. Secondly, important properties of fuel debris for developing defueling tools were identified as shape, size, density, hardness, elastic modulus, fracture toughness, thermal conductivity, specific heat (heat capacity), and melting point. Thirdly, the influence of seawater salt and B{sub 4}C/SUS to characteristics of debris was found, such as deposition of magnesium oxide crystal on the surface of fuel debris. The Influence of Pu to thermal properties of fuel debris was found, such as the increase of melting point. Concerning the second project, the major results are the following. First, a draft of the whole image of scenarios was developed. Secondly, the alkaline resolution method using Na{sub 2}O{sub 2} is most likely to be applied as a part of analysis technologies. Thirdly, it was shown that a part of fuel debris rich in U might be soluble in nitric acid. Fourthly, it was shown that all pyrochemical processes examined have potential to be applied for treating fuel debris. The results of the projects will contribute to the decommissioning program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Single-layer TiO x reconstructions on SrTiO 3 (111): (√7 × √7)R19.1°, (√13 × √13)R13.9°, and related structures

The atomic structures of two reconstructions, (√7 × √7)R19.1° and (√13 × √13)R13.9°, on the SrTiO 3 (111) surface were determined using a combination of density functional theory and scanning tunneling microscopy data and simulations. The combination of these methods allows for potential surface structures to be generated and verified in the absence of diffraction data, providing another tool for solving surface reconstructions. These reconstructions belong to the same stoichiometric, nSrTiO 3 • mTiO 2 , structural family made up of an interconnected, single layer of edge-sharing TiO 6 and TiO 5 [] octahedra. This family is found to include the previously-solved (2 × 2)a reconstruction as its smallest unit-cell sized member and serves as a tool for better understanding and predicting the structure of other reconstructions of arbitrary surface unit-cell size on SrTiO 3 (111). This reconstruction family and the calculations of surface energies for different hypothesis structures also shed light on the structure of Schottky defects observed on these reconstructed SrTO 3 (111) surfaces.

Andersen, Tassie K. (ORCID:0000000295444995)↗