Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “time to failure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Improved Creep and Tensile Properties of a Corrosion Resistant Ni-Based Superalloy Using High Temperature Aging and Nb/Ta Additions

Resistance to creep deformation is essential for cast and wrought Ni-based superalloys in next generation energy systems due to the considerable exposure times required at the operating temperature. Here the amount of precipitate strengthening was increased in variants to Inconel alloy 725 (IN725), a corrosion resistant alloy, to improve its elevated temperature mechanical strength. Additions of Nb or Ta coupled with a high temperature aging (HTA) heat treatment promoted the formation of γ" precipitates and grain boundary phases which led to significant increases in time to failure. The HTA increased the creep life of various alloy formulations as compared to the standard aging heat treatment with a maximum improvement of 371%. The Nb and Ta additions lowered the minimum creep rate (MCR) and had a similar effect on increasing creep life. The positive effect of the additions was more pronounced when coupled with the HTA which employed a higher temperature in the first step of the heat treatment to promote precipitate phase formation. The Ti/Al ratio was used to design alloys with preferential formation of ' or γ" precipitates. Compact morphology precipitates were formed in the alloys with a low Ti/Al ratio. While a low Ti/Al ratio was primarily associated with lower MCRs, the effect on the creep life was less evident than that of the HTA. By using additions of Nb or Ta and a HTA heat treatment, the creep life of IN725 for testing at 973 K (700 °C) and 483 MPa was improved by up to 256%.

36 MATERIALS SCIENCE↗
DOE OSTI2024

In-situ determination of strain during transient burst testing and the temperature dependence of Zircaloy-4 claddings

Understanding fuel system behavior during postulated loss-of-coolant accidents is pertinent for continued safe and efficient operation of light water reactors, particularly as higher burnups are being pursued and safety margins re-evaluated. Conventional mechanical models for the incumbent Zr alloys typically rely on the assumption that steady-state creep is the dominant fuel cladding response during transient accident conditions. To investigate this assumption, simulated accident burst testing was performed on Zircaloy-4 claddings with balloon behavior measured in-situ. Here, two distinct loading conditions were utilized during burst testing: (1) constant-gas-inventory where pressure was allowed to increase with temperature and (2) constant pressure. In-situ strains and strain rates were measured via 2-dimensional digital image correlation techniques and synchronized with temperature to determine deformation dependencies. The temperature dependence of strain rate was characterized by a two segment Arrhenius relationship, with a distinct transition between the high and low temperature/strain regimes. The average activation energy of the lower temperature/strain regime was 328 ± 25 kJ/mol, in agreement with the ~320 kJ/mol used for conventional LOCA models. However, the higher temperature/strain segment, which encompassed most of ballooning, showed increased activation energies as well as a dependence on whether the burst region was in view. For tests that burst away from the camera view, the average high temperature/strain segment activation energy was 635 ± 150 kJ/mol. For samples where the rupture opening formed in view, the average activation energy was 1015 ± 179 kJ/mol. This observed shift in temperature dependence indicates a transition in deformation mechanism at the end of life, possibly to time independent failure mechanisms, which has not yet been visualized in the literature for Zr alloys. Parameters at the transition points were analyzed to determine thresholds for this change in behavior, which occurred at an average hoop strain of 6.9 ± 2.1 %.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Seismic Features Predict Ground Motions During Repeating Caldera Collapse Sequence

Abstract Applying machine learning to continuous acoustic emissions, signals previously deemed noise, from laboratory faults and slowly slipping subduction‐zone faults, demonstrates hidden signatures are emitted that describe physical details, including fault displacement and friction. However, no evidence currently exists to demonstrate that similar hidden signals occur during seismogenic stick‐slip on earthquake faults—the damaging earthquakes of most societal interest. We show that continuous seismic emissions emitted during the 2018 multi‐month caldera collapse sequence at the Kı̄lauea volcano in Hawai'i contain hidden signatures characterizing the earthquake cycle. Multi‐spectral data features extracted from 30 s intervals of the continuous seismic emission are used to train a gradient boosted tree regression model to predict the GNSS‐derived contemporaneous surface displacement and time‐to‐failure of the upcoming collapse event. This striking result suggests that at least some faults emit such signals and provide a potential path to characterizing the instantaneous and future behavior of earthquake faults.

58 GEOSCIENCES↗
DOE OSTI2020

GPU Lifetimes on Titan Supercomputer: Survival Analysis and Reliability

The Cray XK7 Titan was the top supercomputer system in the world for a long time and remained critically important throughout its nearly seven year life. It was an interesting machine from a reliability viewpoint as most of its power came from 18,688 GPUs whose operation was forced to execute three rework cycles, two on the GPU mechanical assembly and one on the GPU circuitboards. We write about the last rework cycle and a reliability analysis of over 100,000 years of GPU lifetimes during Titan’s 6-year-long productive period. Using time between failures analysis and statistical survival analysis techniques, we find that GPU reliability is dependent on heat dissipation to an extent that strongly correlates with detailed nuances of the cooling architecture and job scheduling. We describe the history, data collection, cleaning, and analysis and give recommendations for future supercomputing systems. We make the data and our analysis codes publicly available.

Ostrouchov, George↗
DOE OSTI2020

CoREC: Scalable and Resilient In-memory Data Staging for In-situ Workflows

The dramatic increase in the scale of current and planned high-end HPC systems is leading new challenges, such as the growing costs of data movement and IO, and the reduced mean time between failures (MTBF) of system components. In-situ workflows, i.e., executing the entire application workflows on the HPC system, have emerged as an attractive approach to address data-related challenges by moving computations closer to the data, and staging-based frameworks have been effectively used to support in-situ workflows at scale. However, the resilience of these staging-based solutions has not been addressed, and they remain susceptible to expensive data failures. Furthermore, naive use of data resilience techniques such as n-way replication and erasure codes can impact latency and/or result in significant storage overheads. In this article, we present CoREC, a scalable and resilient in-memory data staging runtime for large-scale in-situ workflows. CoREC uses a novel hybrid approach that combines dynamic replication with erasure coding based on data access patterns. It also leverages multiple levels of replications and erasure coding to support diverse data resiliency requirements. Furthermore, the article presents optimizations for load balancing and conflict-avoiding encoding, and a low overhead, lazy data recovery scheme. We have implemented the CoREC runtime and have deployed with the DataSpaces staging service on leadership class computing machines and present an experimental evaluation in the article. Here, the experiments demonstrate that CoREC can tolerate in-memory data failures while maintaining low latency and sustaining high overall storage efficiency at large scales.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

GPU Lifetimes on Titan Supercomputer: Survival Analysis and Reliability

George Ostrouchov, Don Maxwell, Rizwan Ashraf, Mallikarjun Shankar, and James Rogers. 2020. GPU Lifetimes on Titan Supercomputer: Survival Analysis and Reliability. In Proceedings of the International Conference for High Performance Computing, Networking, Storage and Analysis (SC '20). Association for Computing Machinery, New York, NY, USA. Data and code for SC20 paper about Titan GPU reliability analysis: https://github.com/olcf/TitanGPULife. Includes R code to generate graphics for paper and additional analyses. See code/README for instructions. Includes original Titan GPU reliability data on over 100,000 collective hours of operation: data/titan.gpu.history.txt - history data, data/titan.service.txt - service nodes for exclusion. Includes output data files produced by code/TitanGPUmodel.Rmd: data/gc_full.csv - cleaned up data (see paper and R code); data/gc_summary_loc.csv - one record per GPU (variables: SN, time, nlife, nloc, last, col, row, cage, slot, node, max_loc_events, time_max_loc, dbe, dbe_loc, otb, otb_loc, out, batch, days, years, dead, dead_otb, dead_dbe) (see paper and R code). Includes .Rmd analysis document as TitanGPUmode.html. Includes Python code to process data/gc_full.csv into graphics from time-between-failure analyses: See code/tbf-analyses/README for instructions.

42 ENGINEERING↗
DOE OSTI2020

Multiscale-Informed Modeling of High Temperature Component Response with Uncertainty Quantification

This report summarizes a joint effort between Argonne National Laboratory, Idaho National Laboratory, and Los Alamos National Laboratory to develop and deploy constitutive models targeted at predicting the life of Grade 91 alloy components subjected to high temperature environments typical of those that structural components in advanced nuclear reactors would experience. Two distinct, but complementary constitutive modeling approaches have been taken here. The first employs a phenomenological viscoplastic model for which parameters have been calibrated based on experimental data for a wide range of Grade 91 alloy that has undergone a variety of processing. A Bayesian approach was used to derive distributions of uncertain parameters for this model based on this data set. The second approach is a reduced order model suitable for engineering-scale analysis that is based on the results of a large set of mesoscale simulations. Mesoscale models allow for the microstructure and composition of a particular alloy to be directly taken into account in the computation of the viscoplastic response, but are computationally expensive, which makes it impractical to directly call those models for the material constitutive response in an engineering-scale simulation. The reduced-order representation of the response of the underlying model used here allows for an engineering-scale model to take into account the characteristics of the underlying microstructure, while only incurring a reasonable computational expense. Both of these approaches have different strengths, and are applicable for different parts of the design/analysis process. The phenomenological models can be readily parameterized based on a set of experimental data for a given class of materials and used for scoping calculations. Once a specific material is chosen and adequately characterized, the reduced order models can accurately predict the response of that specific alloy, and because the models are based on predictive models of the underlying microstructure, they can be used to more confidently predict the response under conditions in regions where there is limited experimental data. Both of these models have been integrated in the Grizzly code, which is used here to perform proof-of-concept uncertainty quantification analyses of a simple component under prototypical conditions. The built- in stochastic analysis capabilities in the MOOSE framework that Grizzly is built on are used here to run large sets of simulations for this uncertainty quantification analysis. As would be expected, because the reduced order models are developed for a much more tightly defined alloy, they predict tighter distributions of the time to failure than the phenomenological models, which are calibrated to a broader set of data. Also important is that these simulations demonstrate that a reduced order modeling approach can be successfully deployed to propagate uncertainties from the material scale to practical engineering-scale component simulations.

42 ENGINEERING↗
DOE OSTI2020

Co-Optimization of Boost Converter Reliability and Volumetric Power Density [Brief]

Optimized designs were achieved using a genetic algorithm to evaluate multi-objective trade space, including Mean-Time-Between-Failure (MTBF) and volumetric power density. This work provides a foundational platform that can be used to optimize additional power converters, such as an inverter for the EV traction drive system as well as trade-offs in thermal management due to the use of different device substrate materials.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

High Efficiency OLED Light Engine

LED Specialists has accomplished the program objective in designing a high efficiency OLED light engine combining high-performance OLED panels in the 5W-8W range. We achieved our goal by using an Active-Clamp Flyback circuit topology using state-of-the-art electronics. Evaluation testing of our second-generation prototype PC board has demonstrated an efficiency rating of 93% and dimming capability between 100% and 5% of OLED brightness. A reliability analysis of the design shows it to have a predicted Mean Time Between Failures (MTBF) of approximately 1,000,000 hours.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Customer-Focused Key Performance Indicators for Electric Vehicle Charging

To systematically improve the public charging experience, EV charging industry stakeholders need to define and measure it precisely. Many stakeholders currently measure aspects of the charging experience, but they typically employ metrics that are either operational in nature, such as charger uptime and mean time between failures, or composite customer satisfaction indices. To improve the customer experience most effectively, the industry needs metrics that define the charging experience from the perspective of the customer, not business operations. Furthermore, industry practitioners need granular metrics to know what specific aspects of the charging experience need improvement. This report defines such customer-focused metrics, called key performance indicators (KPIs).

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Broad Spectrum Antifungal Pond Protection

To decrease operating costs associated with fungal infections in algal crops used for biofuel production, we developed bacterial consortia that displayed antifungal properties. These bacteria were grown in culture with algae species without any additional operating costs or need for re-inoculation with bacteria. These co-cultures maintained their antifungal properties for the entirety of the project period and increased mean time to failure (MTTF) by up to 350% when challenged with high levels of fungal pests. Multiple fungal and fungus-like pests were tested and the consortia showed efficacy against three species.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2025

Microscopic Measurement: Need for Nuclear Material Sample Specimen Characterization Capability

The Surveillance, Fabrication, and Off-Site Operations team at Lawrence Livermore National Laboratory is beginning an update to the nuclear material machining lab in Superblock. Plutonium and other nuclear materials tend to accelerate the aging process for equipment and machines that would otherwise be maintainable for long lives. They have their lifespans shortened from deteriorated seals, embrittled polymer components, accelerated corrosion, and damage to electronics from exposure to radioactive materials. The cost of installation of equipment into a glove box (GB) tends to outstrip the cost of the equipment itself. Due to the magnification of cost, the historical approach to equipment installs has been to purchase and install the highest-quality and most robust equipment available to maximize time between failures and updates. To make room for the installation of a new lathe, the inspection GB is being moved to a different location within the machining lab. As part of the overall effort, the equipment within the inspection GB is being revisited. Current measurement capabilities are antiquated and starting to become problematic due to age. Advances in metrology are sought for more comprehensive characterization of scientific samples. This document aims to identify several options for the replacement of current measurement equipment and identify a system for purchase and eventual installation. The intention is not to select the cheapest system, but rather to identify a system that best meets the needs of both the operators and principal investigators (PI). Following the convention of the SYSM-5620 Design Thinking and System Engineering, it was determined that a laser confocal measurement system from Keyence is the most suitable option for our programmatic need. Form factor, capability, and maintainability were considered. Along with stakeholder input, to ensure the best decision for the Nuclear Material Technology Program.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Customer-Focused Key Performance Indicators for Electric Vehicle Charging

To systematically improve the public charging experience, EV charging industry stakeholders need to define and measure it precisely. Many stakeholders currently measure aspects of the charging experience, but they typically employ metrics that are either operational in nature, such as charger uptime and mean time between failures, or composite customer satisfaction indices. To improve the customer experience most effectively, the industry needs metrics that define the charging experience from the perspective of the customer, not business operations. Furthermore, industry practitioners need granular metrics to know what specific aspects of the charging experience need improvement. This report defines such customer-focused metrics, called key performance indicators (KPIs).

33 - ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Adaptive Framework for Maintenance Scheduling Based on Dynamic Preventive Intervals and Remaining Useful Life Estimation

Data-based prognostic methods exploit sensor data to forecast the remaining useful life (RUL) of industrial settings to optimize the scheduling of maintenance actions. However, implementing sensors may not be cost-effective or practical for all components. Traditional preventive approaches are not based on sensor data; however, they schedule maintenance at equally spaced intervals, which is not a cost-effective approach since the distribution of the time between failures changes with the degradation state of other parts or changes in working conditions. This study introduces a novel framework comprising two maintenance scheduling strategies. In the absence of sensor data, we propose a novel dynamic preventive policy that adjusts intervention intervals based on the most recent failure data. When sensor data are available, a method for RUL prediction, designated k-LSTM-GFT, is enhanced to dynamically account for RUL prediction uncertainty. The results demonstrate that dynamic preventive maintenance can yield cost reductions of up to 51.8% compared to conventional approaches. The predictive approach optimizes the exploitation of RUL, achieving costs that are only 3–5% higher than the minimum cost achievable while ensuring the safety of critical systems since all of the failures are avoided.

Nunes, Pedro (ORCID:0000000180012172)↗