Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thin membrane”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Dye laser tuning with pellicles.

Thin nitrocellulose membranes (pellicles) are shown to exhibit properties which make them suitable for intracavity tuning elements in high-energy pulsed dye lasers. Uncoated pellicles of 2-micron and 8-micron thickness with surface figures of lambda/1 are shown to closely approximate the properties of low-finesse etalons with wide free spectral ranges. Pellicles of 8-micron thickness, coated on both surfaces with 50% reflectivity multilayer dielectrics, are shown to be effective as spectral narrowing elements with peak transmission greater than 80% and resultant laser linewidths of 0.57 nm full width at half-maximum.

Mumola, P. B.↗
NASA NTRS1974

Experimental evaluation of compliant surfaces at low speeds

An experimental study was devised to determine the profile drag on a subsonic wind tunnel model partially covered with various compliant surface materials. The model consisted of a large section of constant thickness bounded fore and aft by symmetric airfoil fairings. A flat rigid plate, the control surface, could be exchanged for four contiguous complaint panels. The flexible media generally consisted of thin polyvinylchloride membranes stretched to various tensions over trapped fluid cavities of air, water, or polyethelene oxide solution, or over dry or flooded open-celled polyurethane foams. On the basis of very accurate direct-force cell measurements, all configurations were found to yield profile drags equal to or slightly higher than that obtained for the conventional rigid surface case. The results indicate that the potential for practical drag-reducing applications will be limited to either high-density or high-speed flows where more sensible pressure perturbations occur.

Mcalister, K. W.↗
NASA NTRS1979

Broadband electrostatic acoustic transducer for ultrasonic measurements in liquids

A broadband capacitive electrostatic acoustic transducer (ESAT) has been developed for use in a liquid environment at megahertz frequencies. The ESAT basically consists of a thin conductive membrane stretched over a metallic housing. The membrane functions as the ground plate of a parallel plate capacitor, the other plate being a dc biased electrode recessed approximately 10 microns from the electrically grounded membrane. An ultrasonic wave incident on the membrane varies the membrane-electrode gap spacing and generates an electrical signal proportional to the wave amplitude. The entire assembly is sealed for immersion in a liquid environment. Calibration of the ESAT with incident ultrasonic waves of constant displacement amplitude from 1 to 15 MHz reveals a decrease in signal response with increasing frequency independent of membrane tension. The use of the ESAT as a broadband ultrasonic transducer in liquids with a predictable frequency response is promising.

Cantrell, J. H., Jr.↗
NASA NTRS1980

Broadband electrostatic acoustic transducer for liquids

Capacitive electrostatic transducer (ESAT) measures absolute displacement amplitudes of ultrasonic waves in liquids, and may be used as calibrator for other transducers or as probe for nondestructive study and characterization of materials. ESAT consists of thin conductive membrane stretched over metallic housing. Ultrasonic waves incident on membrane cause it to vibrate and generate signal proportional to wave amplitude. Entire assembly is sealed for immersion in liquid.

Cantrell, J. H.↗
NASA NTRS1981

Acoustic lens is gas-filled

Fluorocarbon gas contained by plastic membrane is effective lens for sound waves. In tests, lens substantially improved accuracy of sound "maps" of turbulent airflow. It could also be used to record sound intensity patterns in design of speakers, lecture halls, and auditoriums. Lens is fabricated by clamping together two membranes of thin plastic and filling enclosed space with fluorocarbon gas. Since speed of sound in gas is considerably less than in air, lens refracts and focuses sound waves, analogous to focusing light by glass lens. Focal length is adjusted simply by changing gas pressure, which changes lens curvature.

Kendall, J. M., Jr.↗
NASA NTRS1982

Conceptual design of electrostatic antenna

The concept of using electrostatic forces to tension a thin, conducting membrane and maintain it in a precision antenna shape is discussed. This electrostatically controlled membrane mirror is an adpative structure which maintains surface quality despite errors in construction, irregularities of materials, solar heating, and on board disturbances.

Coyner, J. V.↗
NASA NTRS1984

In Situ Cross-Linking of Polyvinyl Alcohol Films

Films or impregnated matrices readily made from aqueous polyvinyl alcohol solution. Controlled thickness films made by casting precise quantities of aqueous polymer solution on smooth surface, allowing water to evaporate and then removing film. Composite separators formed in similar fashion by impregnating cloth matrix with polyvinyl alcohol solution and drying composite. Insoluble thin hydrophilic membranes made from aqueous systems, and use of undesirable organic solvents not required.

Philipp, W. H.↗
NASA NTRS1984

Method for the preparation of thin-skinned asymmetric reverse osmosis membranes and products thereof

A method for preparing water insoluble asymmetric membranes from water soluble polymers is discussed. The process involves casting a film of the polymer, partially drying it, and then contacting it with a concentrated solution of a transition metal salt. The transition metal ions render the polymer insoluable and are believed to form a complex with it. Optionally, the polymer is crosslinked with heat or radiation. The most preferred polymer is poly(vinyl alcohol). The most preferred complexing salt is copper sulfate. The process and the metal ion linked membranes are discussed. The membranes are reverse osmosis membranes.

Wydeven, T. J.↗
NASA NTRS1983

A new thermal radiation detector using optical heterodyne detection of absorbed energy

The operating principles of a new kind of room-temperature thermal radiation detector are described. In this device modulated light heats a gas, either directly or by conduction from a thin absorbing membrane, and the resultant change in density of the gas is detected by optical heterodyning. The performance of a membrane device of this kind agrees well with the predictions of theory.

Davis, C. C.↗
NASA NTRS1985

Water ball collision

What happens if a stainless steel ball hits a water ball in the weightless space of the Universe? In other words, it was the objective of our experiments in the Space to observe the surface tension of liquid by means of making a solid collide with a liquid. Place a small volume of water between 2 glass sheets to make a thin water membrane: the 2 ass sheets cannot be separated unless an enormous force is applied. Also, fill a cup with water to the brim, place a sheet of paper on top of it, and turn the cup upside down gently: the water inside the cup does not spill out. It is obvious from these phenomena that the surface tension of water is far greater than presumed. On the earth, however, it is impossible in most cases to observe only the surface tension of liquid, because gravity always acts on the surface tension

Kazuo Fujimoto↗
NASA NTRS1990

Tectonics of planetary loading - A general model and results

The tectonics of planetary loading is investigated using an analytical model for determining the stresses in an arbitrarily thick spherical shell due to an idealized axisymmetric load. The model includes the flat plate and thin shell membrane approximations as end members, and makes it possible to determine the nature of the transition between them. Using this model, the stress states and the resulting tectonic patterns due to an idealized exponential load are determined as functions of five dimensionless parameters: the ratio of the lithospheric thickness to the planetary radius; the decay width of the load; the 'support parameter', which is the ratio of the buoyancy to the flexural support; the angular distance from the load center; and the normalized radial distance from the planet center.

Janes, D. M.↗
NASA NTRS1992

Integrated horn antennas for millimeter-wave applications

The development of integrated horn antennas since their introduction in 1987 is reviewed. The integrated horn is fabricated by suspending a dipole antenna, on a thin dielectric membrane, in a pyramidal cavity etched in silicon. Recent progress has resulted in optimized low- and high-gain designs, with single and double polarization for remote-sensing and communication applications. A full-wave analysis technique has resulted in an integrated antenna with performance comparable to that of waveguide-fed corrugated-horn antennas. The integrated horn design can be extended to large arrays, for imaging and phased-array applications, while leaving plenty of room for the RF and IF processing circuitry. Theoretical and experimental results at microwave frequencies and at 90 GHz, 240 GHz, and 802 GHz are presented.

Rebeiz, Gabriel M.↗
NASA NTRS1992

Geometric modeling of inflatable structures for lunar base

A modular inflatable structure consisting of thin, composite membranes is presented for use in a lunar base. Results from a linear elastic analysis of the structure indicate that it is feasible in the lunar environment. Further analysis requires solving nonlinear equations and accurately specifying the geometries of the structural members. A computerized geometric modeling technique, using bicubic Bezier surfaces to generate the geometries of the inflatable structure, was conducted. Simulated results are used to create three-dimensional wire frames and solid renderings of the individual components of the inflatable structure. The component geometries are connected into modules, which are then assembled based upon the desired architecture of the structure.

Nowak, Paul S.↗
NASA NTRS1992

Millimeter-wave double-dipole antennas for high-gain integrated reflector illumination

A double-dipole antenna backed by a ground plane has been fabricated for submillimeter wavelengths. The double-dipole antenna is integrated on a thin dielectric membrane with a planar detector at its center. Measured feed patterns at 246 GHz agree well with theory and demonstrate a rotationally symmetric pattern with high coupling efficiency to Gaussian beams. The input impedance is around 50 ohms, and will match well to a Schottky diode or SIS detector. The double-dipole antenna served as the feed for a small machined parabolic reflector. The integrated reflector had a measured gain of 37 dB at 119 microns. This makes the double-dipole antenna ideally suited as a feed for high resolution tracking or for long focal length Cassegrain antenna systems.

Filipovic, Daniel F.↗
NASA NTRS1992

Control of resonant frequencies in adaptive structures by prestressing

The natural vibration frequencies of a structure can be affected by inducing stress in the structure. The success of this kind of control of the resonant frequencies of a truss structure depends on the geometry of the structure. It is shown that in adaptive truss structures the method is effective for vibrations in less stiff directions, such as the normal direction of the plane containing all of the bars of a node, suggesting its applicability for cable, membrane, and thin plate and shell structures.

Baycan, Can M.↗
NASA NTRS1993

A 250 GHz planar low noise Schottky receiver

A planar quasi-optical Schottky receiver based on the quasi-integrated horn antenna has been developed and tested over the 230-280 GHz bandwidth. The receiver consists of a planar GaAs Schottky diode placed at the feed of a dipole-probe suspended on a thin dielectric membrane in an etched-pyramidal horn cavity. The diode has a 1.21 micron anode diameter and a low parasitic capacitance due to the use of an etched surface channel. The antenna-mixer results in a measured DSB conversion loss and noise temperature at 258 GHz of 7.2 dB +/- 0.5 dB and 1310 K +/- 70 K, respectively, at room temperature. The design is compatible with SIS mixers, and the low cost of fabrication and simplicity makes it ideal for submillimeter-wave imaging arrays requiring a 10-20 percent bandwidth.

Ali-Ahmad, Walid Y.↗
NASA NTRS2001

Modeling and Analysis of Structural Dynamics for a One-Tenth Scale Model NGST Sunshield

New modeling and analysis techniques have been developed for predicting the dynamic behavior of the Next Generation Space Telescope (NGST) sunshield. The sunshield consists of multiple layers of pretensioned, thin-film membranes supported by deployable booms. Modeling the structural dynamic behavior of the sunshield is a challenging aspect of the problem due to the effects of membrane wrinkling. A finite element model of the sunshield was developed using an approximate engineering approach, the cable network method, to account for membrane wrinkling effects. Ground testing of a one-tenth scale model of the NGST sunshield were carried out to provide data for validating the analytical model. A series of analyses were performed to predict the behavior of the sunshield under the ground test conditions. Modal analyses were performed to predict the frequencies and mode shapes of the test article and transient response analyses were completed to simulate impulse excitation tests. Comparison was made between analytical predictions and test measurements for the dynamic behavior of the sunshield. In general, the results show good agreement with the analytical model correctly predicting the approximate frequency and mode shapes for the significant structural modes.

Johnston, John↗
NASA NTRS2001

Dynamic Testing of a Subscale Sunshield for the Next Generation Space Telescope (NGST)

The NGST sunshield is a lightweight, flexible structure consisting of multiple layers of pretensioned, thin-film membranes supported by deployable booms. The structural dynamic behavior of the sunshield must be well understood in order to predict its influence on observatory performance. Ground tests were carried out in a vacuum environment to characterize the structural dynamic behavior of a one-tenth scale model of the sunshield. Results from the tests will be used to validate analytical modeling techniques that can be used in conjunction with scaling laws to predict the performance of the full-sized structure. This paper summarizes the ground tests and presents representative results for the dynamic behavior of the sunshield.

Lienard, Sebastien↗