Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thin electrolyte”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Al 2 O 3 /TiO 2 coated separators: Roll-to-roll processing and implications for improved battery safety and performance

Heat generation is one of the major concerns with lithium-ion batteries (LIB) while charging them at higher currents, which could inadvertently impact the rate performance and reduce the safety of the cell. Polymer separator is one of the least thermal conductive components of a LIB. In addition, commercial separators for LIB are made from polyolefin membranes that tend to shrink and curl at higher temperatures due to their lower melting temperature (~130 °C). Developing separators with improved thermal stability and higher electrolyte uptake is essential for enhancing the safety as well as the performance of the LIB. In this work, a thin layer of ceramic coatings (Al 2 O 3 and TiO 2 ) is applied on propylene (PP) membrane to improve the thermal stability and electrolyte affinity without compromising the rate performance. A slurry with 100% Al 2 O 3 coated on the polypropylene separator exhibited the best improvement in thermal stability ( shrinkage of 0.6% vs 6.0% for uncoated membrane) and excellent rate performance with 92% capacity retention at 2C. The Al 2 O 3 coated separator demonstrated excellent electrolyte wettability compared to the uncoated membrane. The cross-plane thermal conductivity of the ceramic coated separators is analyzed to understand their heat transfer behavior. The thermal conductivity of the separator is improved by ~3.2 times with the Al 2 O 3 coating.

25 ENERGY STORAGE↗
DOE OSTI2023

Ultra-thin on-chip ALD LiPON capacitors for high frequency application

Multi-layer ceramic capacitors have been used for high frequency decoupling application due to a lower overall impedance leading to fast current response. However, high parasitic inductance limits the application of these capacitors in ultra-high frequency domain. Thus, Multlayer Ceramic Capacitors (MLCCs) are placed close to the IC to improve circuit efficiency and reduce inductance. With next generation applications, the demand for frequency range has further increased which not only requires enhanced capacitor material but improved manufacturing techniques to limit the inductive path. Here, we demonstrate ALD of two different polymorphs of ultra-thin film lithium phosphorus oxynitride (LiPON) as an inorganic solid state electrolyte (SSE) for on chip capacitors for decoupling application. Both the LiPON capacitors shows an electric double layer behavior with a capacitance of 15 μF/cm 2 and a low leakage current (<20 nA/cm 2 ) at 2V. The LiPON shows EDLC behavior up to 10 kHz and beyond, both the polymorphs show an electrostatic behavior with a high dielectric constant (14). Furthermore, this dual frequency behavior along with low parasitic inductance and on chip integration allows for operation in extended frequency ranges.

25 ENERGY STORAGE↗
DOE OSTI2021

Nonlinear ion transport mediated by induced charge in ultrathin nanoporous membranes

Ultrathin membranes with nanoporous conduits show promise for ionic separations and desalination applications, but the mechanisms underlying the nonlinear ionic transport observed in these systems are not well understood. Here, in this work, we demonstrate how induced charge at membrane interfaces can lead to nonlinear ionic transport and voltage-dependent conductance through such channels. The application of an electric field on a polarizable membrane leads to induced charges at the membrane interfaces. The induced charges in turn are screened by diffuse charges in the electrolyte, which are acted upon by the electric field. For extremely thin membranes, the induced charge effect can be significant even for moderate applied voltages commonly used in experiments. We apply a continuum Poisson-Nernst-Planck model to characterize the current-voltage behavior of ultrathin membranes over a wide parameter space. The predictions of the model are compared to recent experiments on graphene and MoS 2 membranes in an electric field. We expect the role of induced charge to be especially pronounced in the limit of atomically thin membranes.

36 MATERIALS SCIENCE↗
NASA NTRS1989

Electrochemical Cell for Obtaining Oxygen from Carbon Dioxide Atmospheres

To support human life on the Martian surface, an electrochemical device will be required to obtain oxygen from the carbon dioxide rich atmosphere. The electrolyte employed in such a device must be constructed from extremely thin, dense membranes to efficiently acquire the oxygen necessary to support life. A forming process used industrially in the production of multilayer capacitors and electronic substrates was adapted to form the thin membranes required. The process, known as the tape casting, involves the suspension consisting of solvents and binders. The suspension is passed under a blade, resulting in the production of ceramic membranes between 0.1 and 0.5 mm thick. Once fired, the stabilized zirconia membranes were assembled into the cell design by employing a zirconium phosphate solution as the sealing agent. The resulting ceramic-to-ceramic seals were found to be structurally sound and gas-tight. Furthermore, by using a zirconia-based solution to assemble the cell, the problem of a thermal expansion mismatch was alleviated. By adopting an industrial forming process to produce thin membranes, an electrochemical cell for obtaining oxygen from carbon dioxide was produced. The proposed cell design is unique in that it does not require a complicated manifold system for separating the various gases present in this process, nor does it require a series of complex electrical connections. Thus, the device can reliably obtain the vital oxygen supply from the toxic carbon dioxide atmosphere.

Hooker, Matthew↗
DOE OSTI2023

Methods and materials for protection of sulfide glass solid electrolytes

A sulfide glass solid electrolyte sheet can be protected from reaction with moisture by a thin metal layer coating converted to a thin electrochemically functional and protective compound layer. The converted protective compound layer is electrochemically functional in that it allows for through transport of lithium ions.

Visco, Steven J.↗
DOE OSTI2024

Methods and materials for protection of sulfide glass solid electrolytes

A sulfide glass solid electrolyte sheet can be protected from reaction with moisture by a thin metal layer coating converted to a thin electrochemically functional and protective compound layer. The converted protective compound layer is electrochemically functional in that it allows for through transport of lithium ions.

Source record↗
DOE OSTI2020

Tutorial on forming through-silicon vias

Through-silicon vias (TSVs) are a critical technology for three-dimensional integrated circuit technology. These through-substrate interconnects allow electronic devices to be stacked vertically for a broad range of applications and performance improvements such as increased bandwidth, reduced signal delay, improved power management, and smaller form-factors. There are many interdependent processing steps involved in the successful integration of TSVs. This article provides a tutorial style review of the following semiconductor fabrication process steps that are commonly used in forming TSVs: deep etching of silicon to form the via, thin film deposition to provide insulation, barrier, and seed layers, electroplating of copper for the conductive metal, and wafer thinning to reveal the TSVs. Recent work in copper electrochemical deposition is highlighted, analyzing the effect of accelerator and suppressor additives in the electrolyte to enable void-free bottom-up filling from a conformally lined seed metal.

42 ENGINEERING↗
DOE OSTI2021

Steric Effect Tuned Ion Solvation Enabling Stable Cycling of High-Voltage Lithium Metal Battery

1,2-Dimethoxyethane (DME) is a common electrolyte solvent for lithium metal batteries. Various DME-based electrolyte designs have improved long-term cyclability of high-voltage full cells. However, insufficient Coulombic efficiency at the Li anode and poor high-voltage stability remain a challenge for DME electrolytes. Here, we report a molecular design principle that utilizes a steric hindrance effect to tune the solvation structures of Li + ions. In this work, we hypothesized that by substituting the methoxy groups on DME with larger-sized ethoxy groups, the resulting 1,2-diethoxyethane (DEE) should have a weaker solvation ability and consequently more anion-rich inner solvation shells, both of which enhance interfacial stability at the cathode and anode. Experimental and computational evidence indicates such steric-effect-based design leads to an appreciable improvement in electrochemical stability of lithium bis(fluorosulfonyl)imide (LiFSI)/DEE electrolytes. Under stringent full-cell conditions of 4.8 mAh cm –2 NMC811, 50 μm thin Li, and high cutoff voltage at 4.4 V, 4 M LiFSI/DEE enabled 182 cycles until 80% capacity retention while 4 M LiFSI/DME only achieved 94 cycles. This work points out a promising path toward the molecular design of non-fluorinated ether-based electrolyte solvents for practical high-voltage Li metal batteries.

25 ENERGY STORAGE↗
NASA NTRS2006

Self-Passivating Lithium/Solid Electrolyte/Iodine Cells

Robust lithium/solid electrolyte/iodine electrochemical cells that offer significant advantages over commercial lithium/ iodine cells have been developed. At room temperature, these cells can be discharged at current densities 10 to 30 times those of commercial lithium/iodine cells. Moreover, from room temperature up to 80 C, the maximum discharge-current densities of these cells exceed those of all other solid-electrolyte-based cells. A cell of this type includes a metallic lithium anode in contact with a commercial flexible solid electrolyte film that, in turn, is in contact with an iodine/ graphite cathode. The solid electrolyte (the chemical composition of which has not been reported) offers the high ionic conductivity needed for high cell performance. However, the solid electrolyte exhibits an undesirable chemical reactivity to lithium that, if not mitigated, would render the solid electrolyte unsuitable for use in a lithium cell. In this cell, such mitigation is affected by the formation of a thin passivating layer of lithium iodide at the anode/electrolyte interface. Test cells of this type were fabricated from iodine/graphite cathode pellets, free-standing solid-electrolyte films, and lithium-foil anodes. The cathode mixtures were made by grinding together blends of nominally 10 weight percent graphite and 90 weight percent iodine. The cathode mixtures were then pressed into pellets at 36 kpsi (248 MPa) and inserted into coin-shaped stainless-steel cell cases that were coated with graphite paste to minimize corrosion. The solid-electrolyte film material was stamped to form circular pieces to fit in the coin cell cases, inserted in the cases, and pressed against the cathode pellets with polyethylene gaskets. Lithium-foil anodes were placed directly onto the electrolyte films. The layers described thus far were pressed and held together by stainless- steel shims, wave springs, and coin cell caps. The assembled cells were then crimped to form hermetic seals. It was found that the solid electrolyte films became discolored within seconds after they were placed in contact with the cathodes - a result of facile diffusion of iodine through the solid electrolyte material (see figure).

Bugga, Ratnakumar↗
DOE OSTI2024

Electroanalytical Exploration of Li Loss at the Solid Electrolyte-Anode Interface in Anode-Free Batteries with Polymer Electrolytes

Li loss during cycling at the solid electrolyte|anode interface strongly determines the cycle life of anode-free solid-state batteries (SSBs). Here, this loss is probed electroanalytically for polymer electrolyte (PE)-based SSBs in anode-free coin cells with practical pressures. A wide range of parameters expected to impact the measured average coulombic efficiency (CE) were explored to estimate the expected range of performance. These factors include PE type, cycling profiles, current collector type, and the presence of a thin Li seed layer. Further, low CE values in the ~50%–85% range are observed for all electrolytes and test conditions. Other than the electrolyte type, a strong dependence of the CE on the electrochemical cycling profile and the type of metallic current collector is observed. Compared to the anode-free setup, the presence of a thin (5 μ m) Li seed layer did not improve the average CE for two out of three PEs, suggesting its presence to be a weak contributor in minimizing the Li loss. This work provides baseline data on the Li losses in low-pressure anode-free configuration cells with PEs.

25 ENERGY STORAGE↗
DOE OSTI2021

Examining CO 2 as an Additive for Solid Electrolyte Interphase Formation on Silicon Anodes

In this study, we demonstrate that the addition of CO 2 to a standard 1.0 M LiPF 6 3:7 wt% ethylene carbonate:ethyl methyl carbonate electrolyte results in the formation of a thinner insoluble solid electrolyte interphase (SEI) that is dominated by the presence of LiF. In contrast, cells without CO 2 result in a thicker insoluble SEI layer containing more organic constituents. The CO 2 is incorporated in the dimethyl carbonate soluble part of the SEI composed primarily of polymeric poly(ethylene oxide) (PEO) on the surface of a thin inorganic layer. This combination of properties from CO 2 addition provides an improved cycling performance through the reduction of irreversible side reactions, leading to higher coulombic efficiency. The results indicate that CO 2 incorporates into the SEI and plays a role similar to additives like fluorinated ethylene carbonate and vinylene carbonate with respect to polymeric components.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

SPUTTERED THIN FILMS FOR VERY HIGH POWER, EFFICIENT, AND LOW-COST COMMERCIAL SOFCS

The aim of this project was to leverage the low area specific resistance (ASR) of Redox’s GDC electrolyte-based cell architecture and increase solid oxide fuel cell (SOFC) efficiency (i.e., open circuit voltage, or OCV) without significantly increasing cell resistance. The key to achieving the increased SOFC efficiency is the introduction of a thin sputtered yttria stabilized zirconia (YSZ) electron-blocking layer and a thin sputtered gadolinia doped ceria (GDC) barrier layer on top of the half-cell substrate (i.e., anode and GDC electrolyte). A key initial effort of the project was to improve the quality of the half-cell substrate surface so that any remaining defects were significantly smaller than the desired film thickness. During lab-scale trials, we had to overcome challenges with film cracking during post-sputtering treatments (e.g., thermal anneals) as well as damage to the sputtering targets. After the initial lab-scale trials, the focus shifted toward the use of commercial scale sputtering equipment with a sputtering equipment manufacturer in the microelectronics industry. Using the commercial sputtering equipment, we deposited films with different variations of power, PO2, sputtering time, platen speed, etc. We then determined the combinations of sputtering conditions and post-sputtering treatments that yielded high-quality films without cracks or other significant defects. While thin films were deposited on cells as large as 10 cm by 10 cm, the processing was optimized using 4 cm by 4 cm cells. Cell performance was evaluated in stainless-steel test fixtures between 500 °C and 700 °C with hydrogen fuel fed to the anode and air fed to the cathode. Extensive studies allowed us to determine that modified cathode and cathode contact firing processes were required to achieve theoretical OCV. Moreover, use of the new firing processes resulted in the need for a modified cathode contact to achieve a low ASR. In summary, the project demonstrated the performance of high OCV (1.13 V at 650 °C) from sputtered layers and a low ASR (~0.25 Ohms-cm2 at 650 °C) resulting from a modification of cathode/contact processing and the introduction of alternative contact layers that are sufficient to yield a Gen-1 cell with a maximum power density of approximately 1.2 W/cm2. At an operating voltage of 0.74 V, this would yield a cell power density of ~1.1 W/cm2. While not utilized in this project, a Redox Gen-2 cell has a catalyst-infiltrated porous anode that reduces the ASR by more than 50% from that of the Gen-1 cells used in this project. Therefore, if the sputtered YSZ electron-blocking layer and GDC barrier layer are added to a Gen-2 half cell with a similar increase in OCV to the theoretical value of ~1.13 V at 650 °C, and if the same improvement in ASR (from that demonstrated in this project) is achieved when using the Gen-2 half-cell architecture as a sputtered cell substrate, then the power density at 0.74 Vop could be as high as ~2.6 W/cm2. The impact of such power density gains, while still maintaining high cell efficiency, and thus high system efficiency, is a dramatic decrease in system cost because the stack represents ~30-40% of the SOFC system cost.

01 COAL, LIGNITE, AND PEAT↗
NASA NTRS2007

A Synopsis of Interfacial Phenomena in Lithium-Based Polymer Electrolyte Electrochemical Cells

The interfacial regions between electrode materials, electrolytes and other cell components play key roles in the overall performance of lithium-based batteries. For cell chemistries employing lithium metal, lithium alloy or carbonaceous materials (i.e., lithium-ion cells) as anode materials, a "solid electrolyte interphase" (SEI) layer forms at the anode/electrolyte interface, and the properties of this "passivating" layer significantly affect the practical cell/battery quality and performance. A thin, ionically-conducting SEI on the electrode surface can beneficially reduce or eliminate undesirable side reactions between the electrode and the electrolyte, which can result in a degradation in cell performance. The properties and phenomena attributable to the interfacial regions existing at both anode and cathode surfaces can be characterized to a large extent by electrochemical impedance spectroscopy (EIS) and related techniques. The intention of the review herewith is to support the future development of lithium-based polymer electrolytes by providing a synopsis of interfacial phenomena that is associated with cell chemistries employing either lithium metal or carbonaceous "composite" electrode structures which are interfaced with polymer electrolytes (i.e., "solvent-free" as well as "plasticized" polymer-binary salt complexes and single ion-conducting polyelectrolytes). Potential approaches to overcoming poor cell performance attributable to interfacial effects are discussed.

Baldwin, Richard S.↗
DOE OSTI2022

Capturing the swelling of solid-electrolyte interphase in lithium metal batteries

Although liquid-solid interfaces are foundational in broad areas of science, characterizing this delicate interface remains inherently difficult because of shortcomings in existing tools to access liquid and solid phases simultaneously at the nanoscale. This leads to substantial gaps in our understanding of the structure and chemistry of key interfaces in battery systems. We adopt and modify a thin film vitrification method to preserve the sensitive yet critical interfaces in batteries at native liquid electrolyte environments to enable cryo–electron microscopy and spectroscopy. We report substantial swelling of the solid-electrolyte interphase (SEI) on lithium metal anode in various electrolytes. Here, the swelling behavior is dependent on electrolyte chemistry and is highly correlated to battery performance. Higher degrees of SEI swelling tend to exhibit poor electrochemical cycling.

25 ENERGY STORAGE↗
DOE OSTI2025

Metal hydrides: a historical perspective

Metal hydrides are known for their outstanding performance as materials for hydrogen storage and processing. These materials find applications for short- and long-term energy storage, compression and supply of hydrogen gas, thermal energy storage, as electrodes and electrolytes in rechargeable batteries, for the microstructural optimisation of functional materials, in thin film technologies, as catalysts, getters and in many other uses. After the discovery of the first binary metal hydrides back in the 19th century, their studies covered all possible binary M-H systems and expanded rapidly into the field of ternary hydrides following the recognition of the excellent hydrogen storage performance of LaNi 5 - and TiFe-based materials, which operate efficiently at room temperature and at near-ambient H 2 pressures. This review aims to provide an overview of the early works, as well as selected recent results on various classes of metal hydrides. It also covers the recent activities from the major contributing countries and continents, including USA, Europe, Japan, China and Australia. These studies relate to achieving the hydrogen storage systems goals set by the Department of Energy in the United States which inspired the research activities at the national and international level, through execution of the tasks on hydrogen-based energy storage managed by the International Energy Agency. The review is prepared by international experts in the field and covers the most important past developments and also presents the recent achievements in the field.

08 HYDROGEN↗
DOE OSTI2022

Engineering Surface Architectures for Improved Durability in III–V Photocathodes

GaInP2 has shown promise as the wide bandgap top junction in tandem absorber photoelectrochemical (PEC) water splitting devices. Among previously reported dual-junction PEC devices with a GaInP 2 top cell, those with the highest performance incorporate an AlInP 2 window layer (WL) to reduce surface recombination and a thin GaInP2 capping layer (CL) to protect the WL from corrosion in electrolytes. However, the stability of these III-V systems is limited, and durability continues to be a major challenge broadly in the field of PEC water splitting. This work provides a systematic investigation into the durability of GaInP 2 systems, examining the impacts of the window layer and capping layer among single junction pn-GaInP 2 photocathodes coated with an MoS 2 catalytic and protective layer. The photocathode with both a CL and WL demonstrates the highest PEC performance and longest lifetime, producing a significant current for >125 h. In situ optical imaging and post-test characterization illustrate the progression of macroscopic degradation and chemical state. The surface architecture combining an MoS 2 catalyst, CL, and WL can be translated to dual-junction PEC devices with GaInP 2 or other III-V top junctions to enable more efficient and stable PEC systems.

08 HYDROGEN↗
NASA NTRS1980

An all-plated, low cost contact system for silicon solar cells

The plating sequences Pd-Cr-Cu and Pd-Ni-Cu are demonstrated. The surface was sensitized with a 50 A-thick Pd layer obtained from an immersion bath. After 15 min heating at 400 C in N2, a thin barrier layer of either Cr or Ni was deposited from electroless baths operated at temperatures around 90 C. The sintering process was repeated, and a thin copper layer of 500 A was deposited by electroless means. An electrolytic copper bath was used to build the copper layer to 3-4 micron thicknesses. Cells with good I-V curves were obtained, and the all-plated contacts had good adhesion. Preliminary cost estimates show that the process costs approximately 12 cents per watt excluding the cost of the masking procedure.

Tanner, D. P.↗