Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “test matrix”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Design, fabrication and test of graphite/polyimide composite joints and attachments for advanced aerospace vehicles

Bonded and bolted designs are presented for each of four major attachment types. Prepreg processing problems are discussed and quality control data are given for lots 2W4604, 2W4632 and 2W4643. Preliminary design allowables test results for tension tests and compression tests of laminates are included. The final small specimen test matrix is defined and the configuration of symmetric step-lap joint specimens are shown. Finite element modeling studies of a double lap joint were performed to evaluate the number of elements required through the adhesive thickness to assess effects of various joint parameters on stress distributions. Results of finite element analyses assessing the effect of an adhesive fillet on the stress distribution in a double lap joint are examined.

Skoumal, D. E.↗
NASA NTRS1982

Contaminant characterization of five satellite materials

An extensive laboratory test program was performed to characterize outgassing of five satellite materials. The materials were Chemglaze Z-306 over 9922 primer, M-773 adhesive, multilayer insulation, polyurethane foam, and silverized Teflon. The souces were prepared to the specifications of a typical satellite program. Dynamic thermogravimetric mass loss characteristics of these five materials were obtained in vacuum with a beam microbalance. The temperature of the material was linearly raised from 25 C to over 650 C while monitoring the mass loss, rate of mass loss, temperature, and the composition of the outgassed material by residual gas analysis. Isothermal source emission/capture coefficients/reemission parameters were obtained with an array of quartz crystal microbalances (QCM). A detailed test matrix in which the temperatures of the QCMs (-160 C, - 100 C, -40 C, and +10 C) and the source material (125 C, and 90 C, and 50 C) were varied was performed. The array of QCMs was also used to measure the spatial distribution of the source emission. The effects of vacuum ultraviolet radiation on the deposition and reemission parameters was determined.

Muscari, J. A.↗
NASA NTRS1982

Small axial turbine stator technology program

An experimental investigation was conducted to determine the effects of surface finish, fillet radius, inlet boundary layer thickness, and free-stream inlet turbulence level on the aerodynamic performance of a small axial flow turbine stator. The principal objective of this program was to help understand why large turbine efficiency is not maintained when a large turbine is scaled to a smaller size. The stator used in this program as a one-sixth scale of a 762 mm (30 in.) diameter stator design with 50 vanes having a vane height of 17 mm (0.666 in.) and an aspect ratio of 1.77. A comprehensive overall test matrix was used to provide a complete engineering understanding of the effects of each variable over the full range of all the other variables. The range of each variable investigated was as follows: surface finish 0.1 micro (4 micro in.) to 2.4 micro (95 micro in.); boundary layer thickness 2 to 25 percent of channel height at each wall; fillet radius 0 mm (0 in.) to 1.0 mm (.040 in.) and turbulence 2 to 12 percent.

Brockett, W.↗
NASA NTRS1981

Verification of the Space Shuttle entry GN&C system

The certification procedures for the initial Shuttle flight are discussed. Particular attention is paid to the entry guidance, navigation, and control (GNC) verification, comprising tests, analysis, demonstration, inspection, and simulation. Flow diagrams for the verification and operational flight sequences are provided, along with a block diagram of the GNC circuitry interfaces. The development of the test matrix software for the GNC is outlined, noting the constant interplay between software verification and spacecraft reconfiguration to meet simulated performance requirements. Comparison of GNC performance predictions with actual entry flight data showed a good match in all performance areas except for sideslip excursions, bank overshoots, an area of transonic buffet, and an increased lift/drag ratio in the preflare to landing flight phase.

Van Hoften, J. D. A.↗
NASA NTRS1981

Fatigue mechanisms in metal matrix composite laminates

Certain aspects of the damage process are described. The shakedown phenomenon in laminates is first explained. This is followed by a presentation of matrix test data used in evaluating the shakedown limits of the laminates used in the subsequent experiments. Test results suggesting that there is no loss of elastic stiffness in laminates loaded at constant amplitudes within their shakedown limits are presented. Damage accumulation and the development of the saturation damage state are illustrated by experimental results on specimens loaded outside the shakedown range. Attention is also given to the behavior of laminates subjected to variable cyclic loading.

Dvorak, G. J.↗
NASA NTRS1982

Experimental evaluation of inlet turbulence, wall boundary layer, surface finish, and fillet radius on small axial turbine state performance

The results of an experimental investigation are presented which establish the effects of surface finish, fillet radius, inlet boundary layer thickness, and free-stream inlet turbulence level on the aerodynamic performance of a small axial flow turbine stator. The principal objective was to help understand why large turbine efficiency is not maintained when a large turbine is scaled to a smaller size and to provide the turbine designer with the performance compromises expected for a small scale design. A comprehensive test matrix was used to gain an understanding of the effects of each variable over the full range of all the other variables.

Kozak, A. A.↗
NASA NTRS1985

Constitutive Cyclic Deformation Behavior in Single-crystal and Directionally Solidified SSME High-pressure Fuel Turbopump Airfoil Materials

The major goal of the project is to correlate mechanical properties with microstructural deformation behavior and to develop models for constitutive response under a variety of monotonic and cyclic loading cycles, temperatures, strain levels, strain rates, and environments. Two alloys are being studied as candidate SSME turbine blade materials. The first is PWA 1480, which is a single-crystal alloy whose nominal composition is reported. The second alloy being studied is D.S. Mar-M 246 + Hf. This is a directionally solidified material, and its nominal composition is also reported. The major areas of interest for the two materials will be slightly different. The single-crystal alloy lends itself well to fundamental deformation studies, since resolved shear stresses on slip planes are all known and only one grain is present. The D.S. material presents an excellent opportunity to study the effects of slightly misaligned grains on deformation behavior. The two materials will be studied by using approximately the same test matrix, so a good degree of direct comparison will also be possible.

Milligan, W. W.↗
NASA NTRS1986

A space station Structures and Assembly Verification Experiment, SAVE

The Space Station structure has been baselined to be a 5 M (16.4 ft) erectable truss. This structure will provide the overall framework to attach laboratory modules and other systems, subsystems and utilities. The assembly of this structure represents a formidable EVA challenge. To validate this capability the Space Station Structures/Dynamics Technical Integration Panel (TIP) met to develop the necessary data for an integrated STS structures flight experiment. As a result of this meeting, the Langley Research Center initiated a joint Langley/Boeing Aerospace Company study which supported the structures/dynamics TIP in developing the preliminary definition and design of a 5 M erectable space station truss and the resources required for a proposed flight experiment. The purpose of the study was to: (1) devise methods of truss assembly by astronauts; (2) define a specific test matrix for dynamic characterization; (3) identify instrumentation and data system requirements; (4) determine the power, propulsion and control requirements for the truss on-orbit for 3 years; (5) study the packaging of the experiment in the orbiter cargo bay; (6) prepare a preliminary cost estimate and schedule for the experiment; and (7) provide a list of potential follow-on experiments using the structure as a free flyer. The results of this three month study are presented.

Russell, R. A.↗
NASA NTRS1986

Thermal environment around the Space Shuttle with hot-gas jets for ice suppression

To prevent prelaunch ice formation on the external tank of the Space Shuttle, the final selected approach is to heat the surrounding air with vertical hot-gas jets located at the launch pad. This approach was considerably more cost-effective than other ice suppression methods considered, although its feasibility was not easily discernible due to the complex flowfield interactions. This paper describes how the use of vertical jets was first evaluated with the aid of a computational fluid dynamics (CFD) technique. An existing general-purpose CFD program (PHOENICS) was used to predict the thermal environment around the Shuttle under various jet configurations and wind conditions. The program accounts for effects of buoyancy, turbulence, and structural obstructions in the flowfield. The computed results showed physically plausible and consistent trends. The wind wake effects were found to be significant, and normally resulted in higher temperatures on the leeward side of the tank. High wind conditions were found to be more severe than calm wind conditions. The use of four jets with two different temperatures was identified as a promising option in which the air temperatures were raised sufficiently to prevent ice formation on the external tank, without excessive increase in Orbiter surface temperature. The use of the numerical model also facilitated the selection of test configurations and a test matrix for verifying the approach. Selected results of an experimental verification (by using a 2 percent scale model in a wind tunnel) are also presented.

Singhal, A. K.↗
NASA NTRS1988

The effects of leading edge and downstream film cooling on turbine vane heat transfer

The progress under contract NAS3-24619 toward the goal of establishing a relevant data base for use in improving the predictive design capabilities for external heat transfer to turbine vanes, including the effect of downstream film cooling with and without leading edge showerhead film cooling. Experimental measurements were made in a two-dimensional cascade previously used to obtain vane surface heat transfer distributions on nonfilm cooled airfoils under contract NAS3-22761 and leading edge showerhead film cooled airfoils under contract NAS3-23695. The principal independent parameters (Mach number, Reynolds number, turbulence, wall-to-gas temperature ratio, coolant-to-gas temperature ratio, and coolant-to-gas pressure ratio) were maintained over ranges consistent with actual engine conditions and the test matrix was structured to provide an assessment of the independent influence of parameters of interest, namely, exit Mach number, exit Reynolds number, coolant-to-gas temperature ratio, and coolant-to-gas pressure ratio. Data provide a data base for downstream film cooled turbine vanes and extends the data bases generated in the two previous studies. The vane external heat transfer obtained indicate that considerable cooling benefits can be achieved by utilizing downstream film cooling. The data obtained and presented illustrate the interaction of the variables and should provide the airfoil designer and computational analyst the information required to improve heat transfer design capabilities for film cooled turbine airfoils.

Hylton, L. D.↗
NASA NTRS1989

Laser transit anemometer software development program

Algorithms were developed for the extraction of two components of mean velocity, standard deviation, and the associated correlation coefficient from laser transit anemometry (LTA) data ensembles. The solution method is based on an assumed two-dimensional Gaussian probability density function (PDF) model of the flow field under investigation. The procedure consists of transforming the data ensembles from the data acquisition domain (consisting of time and angle information) to the velocity space domain (consisting of velocity component information). The mean velocity results are obtained from the data ensemble centroid. Through a least squares fitting of the transformed data to an ellipse representing the intersection of a plane with the PDF, the standard deviations and correlation coefficient are obtained. A data set simulation method is presented to test the data reduction process. Results of using the simulation system with a limited test matrix of input values is also given.

Abbiss, John B.↗
NASA NTRS1988

Droplet combustion at reduced gravity

The current work involves theoretical analyses of the effects identified, experiments in the NASA Lewis drop towers performed in the middeck areas of the Space Shuttle. In addition, there is laboratory work associated with the design of the flight apparatus. Calculations have shown that some of the test-matrix data can be obtained in drop towers, and some are achievable only in the space experiments. The apparatus consists of a droplet dispensing device (syringes), a droplet positioning device (opposing, retractable, hollow needles), a droplet ignition device (two matched pairs of retractable spark electrodes), gas and liquid handling systems, a data acquisition system (mainly giving motion-picture records of the combustion in two orthogonal views, one with backlighting for droplet resolution), and associated electronics.

Dryer, F. L.↗
NASA NTRS1990

Damage states in laminated composite three-point bend specimens: An experimental-analytical correlation study

Damage states in laminated composites were studied by considering the model problem of a laminated beam subjected to three-point bending. A combination of experimental and theoretical research techniques was used to correlate the experimental results with the analytical stress distributions. The analytical solution procedure was based on the stress formulation approach of the mathematical theory of elasticity. The solution procedure is capable of calculating the ply-level stresses and beam displacements for any laminated beam of finite length using the generalized plane deformation or plane stress state assumption. Prior to conducting the experimental phase, the results from preliminary analyses were examined. Significant effects in the ply-level stress distributions were seen depending on the fiber orientation, aspect ratio, and whether or not a grouped or interspersed stacking sequence was used. The experimental investigation was conducted to determine the different damage modes in laminated three-point bend specimens. The test matrix consisted of three-point bend specimens of 0 deg unidirectional, cross-ply, and quasi-isotropic stacking sequences. The dependence of the damage initiation loads and ultimate failure loads were studied, and their relation to damage susceptibility and damage tolerance of the mean configuration was discussed. Damage modes were identified by visual inspection of the damaged specimens using an optical microscope. The four fundamental damage mechanisms identified were delaminations, matrix cracking, fiber breakage, and crushing. The correlation study between the experimental results and the analytical results were performed for the midspan deflection, indentation, damage modes, and damage susceptibility.

Starbuck, J. Michael↗
NASA NTRS1989

An experimental study of turbine vane heat transfer with leading edge and downstream film cooling

This paper presents the effects of downstream film cooling, with and without leading edge showerhead film cooling, on turbine-vane external heat transfer. Steady-state experimental measurements were made in a three-vane linear two-dimensional cascade. The principal independent parameters were maintained over ranges consistent with actual engine conditions. The test matrix was structured to provide an assessment of the independent influence of parameters of interest, namely, exit Mach number, exit Reynolds number, coolant-to-gas temperature ratio, and coolant-to-gas pressure ratio. The data obtained indicate that considerable cooling benefits can be achieved by utilizing downstream film cooling. The downstream film cooling process was shown to be a complex interaction of two competing mechanisms. The thermal dilution effect, associated with the injection of relatively cold fluid, results in a decrease in the heat transfer to the airfoil. Conversely, the turbulence augmentation, produced by the injection process, results in increased heat transfer to the airfoil.

Nirmalan, V.↗
NASA NTRS1990

Fatigue testing of plasma-sprayed thermal barrier coatings, volume 2

A plasma sprayed thermal barrier coating for diesel engines were fatigue tested. Candidate thermal barrier coating materials were fatigue screened and a data base was generated for the selected candidate material. Specimen configurations are given for the bend fatigue tests, along with test setup, specimen preparation, test matrix and procedure, and data analysis.

Cruse, T. A.↗
NASA NTRS1991

Pressurization and expulsion of cryogenic liquids: Generic requirements for a low gravity experiment

Requirements are presented for an experiment designed to obtain data for the pressurization and expulsion of a cryogenic supply tank in a low gravity environment. These requirements are of a generic nature and applicable to any cryogenic fluid of interest, condensible or non-condensible pressurants, and various low gravity test platforms such as the Space Shuttle or a free-flyer. Background information, the thermophysical process, preliminary analytical modeling, and experimental requirements are discussed. Key parameters, measurements, hardware requirements, procedures, a test matrix, and data analysis are outlined.

Vandresar, Neil T.↗
NASA NTRS1991

Progress of simulations for reacting shear layers

An attempt was made to develop a high speed, chemically reactive shear layer test rig. The purpose of the experiment was to study the mixing of oxidizer and fuel streams in reacting shear layers for various density, velocity, and Mach number. The primary goal was to understand the effects of the compressibility upon mixing and combustion in a fundamental way. Therefore, a two-dimensional shear layer is highly desirable for its simplicity to quantify the compressibility effects. The RPLUS 2D code is used to calculate the flow fields of different sections of the test rig. The emphasis was on the supersonic nozzle design, the vitiation process for the hot air stream and the overall thermodynamic conditions of the test matrix. The k-epsilon turbulence model with wall function was successfully implemented in the RPLUS code. The k and epsilon equations are solved simultaneously and the LU scheme is used to make it compatible with the flow solver.

Yu, Sheng-Tao↗
NASA NTRS1993

Full-scale wind tunnel investigation of a helicopter individual blade control system

This paper discusses the preparations and plans to test an individual rotor blade pitch control system in the 40- by 80- Foot Wind Tunnel at the NASA Ames Research Center. The test will be performed on a full-scale BO-105 rotor system using a control system made by Henschel Flugzeug-Werke, GmbH, Germany. The Individual Blade Control (IBC) actuators have been designed to replace the pitchlinks of the rotor system. The paper presents a brief historical perspective on the development of the individual blade control system and then describes the present IBC actuators and the wind tunnel test hardware. A discussion of the intended test matrix, expected potential benefits of IBC, and simulation results are included.

Jacklin, Stephen A.↗