SEARCH · Engineering Papers
Results for “tailoring”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Phosphoric acid pre-treatment to tailor polybenzimidazole membranes for vanadium redox flow batteries
We repot vanadium redox flow batteries (VRFBs) use ion-selective membranes for transporting ionic species while separating the positive and negative electrolytes. In this paper, we report phosphoric acid doped polybenzimidazole (PBI) membranes that yield high ionic selectivity and conductivity in VRFBs. The phosphoric acid pre-treatment swells the PBI matrix irreversibly and increases its sulfuric acid doping in VRFB electrolytes. The pre-treated membranes show comparable area resistance with Nafion-212 with better selectivity towards vanadium ions. A low resistance was obtained with a reduced membrane thickness, which can reduce the overall cost of materials. The VRFB using an optimized phosphoric acid pre-treated PBI membrane demonstrates coulombic, voltage, and energy efficiencies of 99.7, 90.3, and 90.0%, respectively, at 40 mA cm -2 while achieving ~40% higher discharge capacity compared to Nafion-212. Furthermore, the VRFB cell shows excellent cycling stability, i.e., only 6.8% or 0.068% per cycle capacity decay for 100 cycles while maintaining coulombic efficiency at >99.9% (98.5% coulombic efficiency for Nafion-212 with a capacity decay of 0.42% per cycle) proving the effectiveness of pre-treatment of phosphoric acid on PBI membranes.
Comparison of powder bed fusion and directed energy deposition for tailoring mechanical properties of traditionally brittle alloys
The mechanical performance of an Fe-Co intermetallic alloy processed by laser powder bed fusion (L-PBF) and laser directed energy deposition (L-DED) additive manufacturing is compared. L-PBF material was characterized by high strength (500–550 MPa) and high ductility (35%) in tension, corresponding to a ~250% increase in strength and an order-of-magnitude improvement in ductility relative to conventional material. Conversely, L-DED material exhibited similarly poor tensile properties to the conventional wrought alloy, with low strength (200–300 MPa) and low ductility (0–2.7%). Finally, the disparity in properties between L-PBF and L-DED material is discussed in the context of the fundamental differences between manufacturing methods.
Sol-gel derived silica: A review of polymer-tailored properties for energy and environmental applications
Not Available
Tailoring microstructure and strength through selective remelting in laser powder bed fusion
Not Available
Tailoring conductive networks within hollow carbon nanospheres to host phosphorus for advanced sodium ion batteries
The formidable sustainability challenges in advancing energy storage technologies call for game-changing research in battery designs. The previous pursuing of novel cathode materials with high redox potentials impedes the vast applications due to the simultaneous electrolyte decomposition at high potentials, though they are expected to deliver high specific capacities. Eventually, people start thinking in an opposite way, desirable anode materials with low redox potentials can also own high specific capacities. Among all the promising candidates, phosphorus-based anodes in sodium ion batteries (SIBs) have received considerable attention owing to the low cost and relatively high natural abundance of phosphorus. More importantly, phosphorus can store three sodium atoms and enable a high theoretical capacity of 2596 mAh g -1 , which overwhelms any other SIB anode currently available. However, the poor electronic conductivity and large volume change of phosphorus during cycling severely deteriorate battery performance. The most widely used strategy is to confine phosphorus within well-designed carbon hosts. Here, we thereby introduce a new type of porous hollow carbon with conductive-network interior as phosphorus host, which not only improves the electrical conductivity, but also creates enough interior surface for maximizing phosphorus utilization and shortening the ion's diffusion distance, compared to those conventional hollow carbon hosts. Therefore, the as-prepared red phosphorus-carbon spheres composites (RP/CS) exhibit superior rate performance (similar to 1083 mAh g -1 at 4 A g -1 , similar to 837 mAh g -1 even at 8 A g -1 ) and excellent cycle life (1027 mAh g -1 at 4 A g -1 more than 2000 cycles).
Tailoring copper current collector roughness and crystallographic orientation to improve lithium plating
Secondary lithium metal batteries are of great interest due to a high theoretical energy density, but rechargeability is limited by the formation of lithium dendrites that lead to internal short circuits and catastrophic cell failure. Mitigating dendrites through uniform current distribution at the current collector is a promising solution to enabling long cycle life of lithium metal electrodes. Here, the impact of copper crystal orientation and roughness on electrochemically deposited lithium morphology is studied. For 50 cycles, the capacity retention from greatest to least followed polycrystalline copper 95 ± 1 % (MC-PC) ≥ 94.55 ± 0.01 % Cu (110) > 93.0 ± 0.4 % Cu(111) > 75.8 ± 0.1 % Cu(100). Cu(100) performed the worst in all cases with shorts occurring frequently before reaching 50 cycles. Cryo-scanning electron microscopy images showed that after 50 cycles, MC-PC Cu had the best lithium morphology, but at early cycles, Cu(111) formed the densest lithium layer. MC-PC Cu had the most uniform lithium nucleation which may have been caused by increased roughness relative to the single crystal samples. When polycrystalline Cu (F-PC) roughness was systematically controlled, the cumulative Coulombic efficiency increased from about 0.3–0.5 with increasing roughness from an Ra of about 10–40 nm. Lastly, plating rates were studied. Slower rates of 0.25 mA/cm 2 exhibited denser lithium morphology in all cases as compared to 0.5 and 1.0 mA/cm 2 , but the relative porosity of Li deposited on the different current collectors depended on the rate applied.
Ammonium enables reversible aqueous Zn battery chemistries by tailoring the interphase
Explore the source record for details and available documents.
Tailoring optoelectronic properties of CH3NH3PbI3 perovskite photovoltaics using al nanoparticle modified PC61BM layer
Not Available
Unraveling a path for multi-cycle recycling of tailored fiber-reinforced vitrimer composites
Not Available
Tough and recyclable carbon-fiber composites with exceptional interfacial adhesion via a tailored vitrimer-fiber interface
Not Available
Tailored glycolysis of Nylon 6 to enable upcycling into high-strength adhesives
Nylon is a high-strength polyamide widely used in automotive, textiles, packaging, etc. However, its durability makes nylon waste difficult to manage, with recycling limited to mechanical grinding to make fillers. Here, we report a catalytic glycolysis approach to deconstruct Nylon 6 into controlled-length oligomers, enabling upcycling into value-added materials. A low-molecular-weight oligomer (M n = 1.8 kg/mol) was repolymerized with diepoxy-terminated poly(bisphenol A-co-epichlorohydrin) via mechanochemistry to create a high-performance adhesive. This copolymer achieves lap shear strengths over 22 MPa on steel and bonds steel to carbon fiber composites, nearly tripling the performance of commercial adhesives even at 90°C. Thermomechanical analyses show that the adhesive retains thermal stability similar to nylon 6 but melts at lower temperatures, allowing easier processing. The material can be reprocessed and reused without significant performance loss. This study demonstrates a strategy to convert nylon 6 waste into valuable materials, offering a sustainable path for difficult-to-recycle plastics.
High titer methyl ketone production with tailored Pseudomonas taiwanensis VLB120
Not Available
Nanostructured Block Polymer Electrolytes: Tailoring Self-Assembly to Unlock the Potential in Lithium-Ion Batteries
Ion-containing solid block polymer (BP) electrolytes can self-assemble into microphase-separated domains to facilitate the independent optimization of ion conduction and mechanical stability; this assembly behavior has the potential to improve the functionality and safety of lithium-ion batteries over liquid electrolytes to meet future demands (e.g., large capacities and long lifetimes) in various applications. However, significant enhancements in the ionic conductivity and processability of BPs must be realized for BP-based electrolytes to become robust alternatives in commercial devices. Toward this end, the controlled modification of BP electrolytes’ intra-domain (nanometer-scale) and multi-grain (micrometer-scale) structure is one viable approach; intra-domain ion transport and segmental compatibility (related to the effective Flory–Huggins parameter, χ eff ) can be increased by tuning the ion and monomer-segment distributions, and the morphology can be selected such that the multi-grain transport is less sensitive to grain size and orientation.
Identifying Lanthanide Energy Levels in Semiconductor Nanoparticles Enables Tailored Multicolor Emission through Rational Dopant Combinations
Not Available