Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “tailoring”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Static and Dynamic Aeroelastic Tailoring With Variable Camber Control

This paper examines the use of a Variable Camber Continuous Trailing Edge Flap (VCCTEF) system for aeroservoelastic optimization of a transport wingbox. The quasisteady and unsteady motions of the flap system are utilized as design variables, along with patch-level structural variables, towards minimizing wingbox weight via maneuver load alleviation and active flutter suppression. The resulting system is, in general, very successful at removing structural weight in a feasible manner. Limitations to this success are imposed by including load cases where the VCCTEF system is not active (open-loop) in the optimization process, and also by including actuator operating cost constraints.

Stanford, Bret K.↗
NASA NTRS2016

Comparison of Curvilinear Stiffeners and Tow Steered Composites for Aeroelastic Tailoring of Transports

A series of aeroelastic optimization problems are solved on a high aspect ratio wingbox of the Common Research Model, in an effort to minimize structural mass under coupled stress, buckling, and flutter constraints. Two technologies are of particular interest: tow steered composite laminate skins and curvilinear stiffeners. Both methods are found to afford feasible reductions in mass over their non-curvilinear structural counterparts, through both distinct and shared mechanisms for passively controlling aeroelastic performance. Some degree of diminishing returns are seen when curvilinear stiffeners and curvilinear fiber tow paths are used simultaneously.

Stanford, Bret K.↗
NASA NTRS2018

Tailored Wingbox Structures through Additive Manufacturing: A Summary of Ongoing Research at NASA LaRC

The use of wingbox structural design for improved performance (i.e., fuel burn reduction) of subsonic transports is driven by two trends: reduced structural weight and increased wingspan. These two trends are in direct competition, as the increased span will exacerbate the structural reaction to aerodynamic loading, and the reduced structural weight will nominally weaken the aircraft’s ability to handle this response. Novel structural configurations, enabled by recent improvements in manufacturing, may be critical toward bridging this gap.This paper summarizes pertinent activities at the NASA Langley Research Center in terms of additive manufacturing of metallic wing structures and substructures. Numerical design optimization activities are summarized as well, in order to understand where on a wingbox an additively-manufactured part may be useful and the way in which that part beneficially impacts the flight physics. The paper concludes with a discussion of how these two research paths may be better married in order to fully integrate both the benefits and realistic limitations of additive manufacturing and numerical structural design.

Stanford, Bret. K.↗
NASA NTRS2020

Passive Aeroelastic Tailored Wing Modal Test Using the Fixed Base Correction Method

In modal testing and finite element model correlation, analysts desire modal results using free-free or rigid boundary conditions to ease comparisons of test versus analytical data. It is often expensive both in cost and schedule to build and test with boundary conditions that replicate the free-free or rigid boundaries. Static test fixtures for load testing are often large, heavy, and unyielding, but do not provide adequate boundaries for modal tests because they are dynamically too flexible and often contain natural frequencies within the frequency range of interest of the test article. Dynamic coupling between the test article and test fixture complicates the model updating process because significant effort is required to model the test fixture and boundary conditions in addition to the test article. If there were a way to correct the modal results for fixture coupling, then setups used for other structural testing could be adequate for modal testing. In the case described in this paper, a partial static loads testing setup was used, which allowed significant schedule and cost savings by eliminating a unique setup for a modal test. A fixed base correction technique was investigated during modal testing of a flexible wing cantilevered from part of a static test fixture. The technique was successfully used to measure the wing modes de-coupled from the dynamically active test fixture. The technique is promising for future aircraft applications, but more research is needed.

structural dynamics↗
NASA NTRSDate not supplied

Tailored Arrival Manager Plan for ecoD 2020

TAM is an automated approach to ensuring safe separation while maximizing throughput and efficiency; as currently conceived, it would serve as an ATC tool. TAM relies on NASA’s Autoresolver technology to compute trajectory-based arrival solutions that provide separation assurance while maximizing airspace and airport capacity utilization. In addition, TAM enables optimized profile descents that minimize altitude level offs and speed interruptions. Importantly, TAM trajectory clearances are intended for delivery to the flight deck through datacomm rather than voice-based communications. Once received on the flight deck, TAM solutions can be auto-loaded into a Flight Management System (FMS) for precision guidance and control along the intended arrival trajectory.

Richard A Coppenbarger↗
NASA NTRS1993

Tailorable Doping-Spike PtSi Infrared Detectors Fabricated by Si Molecular Beam Epitaxy

By incorporating a 1-nm-thick p+ doping spike at the PtSi/Si interface, we have successfullydemonstrated extended cutoff wavelengths of PtSi Schottky infrared detectors. The extended cutoffwavelengths resulted from the reduced effective potential barriers due to the combined effects of anincreased electric field near the silicide/Si interface and the Schottky image force. The p+ dopingspikes were grown by molecular beam epitaxy at 450 degrees C using elemental boron as the dopantsource, with doping concentrations ranging from 5 x 10^(19) to 2 x 10^(20) cm^(-3). The cutoffwavelengths were shown to increase with increasing doping concentrations of the p+ spikes. Thermionic emission dark current characteristics were observed and photoresponse in the LWIRregime was demonstrated. Furthermore, the effective potential barriers determined by the Richardsonplots were used to study the electrically activated boron dopant concentrations of the thin (1-nm-thick) spikes.

del Castillo, H. M.↗
NASA NTRSDate not supplied

Tailoring of NASA-STD-3001 to Lunar Gateway Program Requirements

The Gateway Program must meet NASA's Agency-level human rating requirements, which are intended to accommodate human capabilities and limitations while protecting the safety of the crew, and providing to the maximum extent practical, the capability to safely recover the crew from hazardous situations. Human systems integration represents a key human rating component of Moon to Mars systems to support the execution of Artemis missions, including compliance with mandatory standards for Health and Medical, Safety and Mission Assurance, and Engineering. The human system requirements, together with the human systems integration plan, medical operations requirements, and Gateway sub-system specifications, represent the flow-down of NASA Health and Medical Standards (NASA-STD-3001, Volumes 1 and 2) into the Gateway system. This paper discusses how these documents and other human systems integration activities provide full consideration of human capabilities and limitations as part of the total system design trade space, serving as an example on how the human must be effectively integrated as part of the system in order to achieve mission success. At a bigger scale, the paper con-tributes to the application of systems engineering standards to cutting-edge space exploration initiatives and to the dialogue on how systems engineering can continue to evolve to meet the needs of such ambitious projects.

Systems engineering↗