Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface reactor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Foreword Special issue on the Kilopower Project, Kilowatt Reactor Using Stirling TechnologY (KRUSTY) Test

This special issue of Nuclear Technology contains full-length, peer-reviewed papers describing the design work leading up to and the results of the Kilowatt Reactor Using Stirling TechnologY (KRUSTY) test. KRUSTY was the centerpiece of the National Aeronautics and Space Administration (NASA) Kilopower Project to design, build, and test a space nuclear reactor. This test was the first such test since the end of the Space Nuclear Auxiliary Power (SNAP) project at the end of the 1960s. In this issue, the introduction paper presents the goals of the Kilopower Project and the potential missions this reactor concept could serve in NASA. Kilopower was intended to serve both human exploration needs on planetary surfaces as well as science needs for deep-space exploration. The design work for the experiment by Poston and the power conversion development by Gibson present the pre-work required to perform the eventual KRUSTY test. A paper on regulatory analysis follows, to show the path used to gain approval of the proposed experiment. Then, the early zero-power critical experiments are presented by Sanchez and Grove. These experiments were essential data used to enhance model predictions prior to the high-temperature test. Next, Poston presents the three experiments (warm criticals) that increase the temperature in an incremental fashion prior to the final experiment. These experiments were used to achieve final regulatory approval of the final high-temperature experiment. The last paper by Poston presents the results of the steady-state and transient testing of the reactor at full power and at the design temperature. These results show that the reactor design and as-built experiment met all of the requirements that NASA had developed for the system. Any experiment of this magnitude was accomplished only because of the hard work and dedication of a large number of people at multiple institutions, including the NASA Glenn Research Center, NASA Marshall Space Flight Center, Y-12 National Security Site, Los Alamos National Laboratory, and the Nevada National Security Site prime contractor (formerly National Security Technologies and now the Mission Support and Test Services). The project was jointly funded by the Space Technology Mission Directorate at NASA and the Criticality Safety Program at the National Nuclear Security Administration (NNSA). A special thanks to Jerry McKamy and Angela Chambers at the NNSA and Lee Mason and Don Palac at NASA for their support and guidance. For the authors and multitude of staff that performed this work, the passion for space nuclear reactors was the key to making this experiment a reality.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI1995

Nuclear Safety [Vol. 36, No. 1, January-June 1995]

Nuclear Safety is a journal that covers significant issues in the field of nuclear safety. Its primary scope is safety in the design, construction, operation, and decommissioning of nuclear power reactors worldwide and the research and analysis activities that promote this goal, but it also encompasses the safety aspects of the entire nuclear fuel cycle, including fuel fabrication, spent-fuel processing and handling, and nuclear waste disposal, the handling of fissionable materials and radioisotopes, and the environmental effects of all these activities. Table of Contents for this issue follows. THE CHORNOBYL ACCIDENT: 1 The Chornobyl Accident Revisited, Part II: The State of the Nuclear Fuel Located Within the Chornobyl Sarcophagus, A A. Borovoi and A. R. Sich; GENERAL SAFETY CONSIDERATIONS: 33 Nuclear Power Safety in Central and Eastern Europe, R. Wilson; 46 Safety of Nuclear Power Reactors in the Former Eastern European Countries, S. Chakraborty; 53 Technical Note: On the Definition of Common-Cause Failures, H. Paula; ACCIDENT ANALYSIS: 58 Modeling and Analysis of Core-Debris Recriticality During Hypothetical Severe Accidents in the Advanced Neutron Source Reactor, S.-H. Kim, V. Georgevich, D. B. Simpson, C. O. Slater, and R. P. Taleyarkhan; 68 Ignitability of Hydrogen/Oxygen/Diluent Mixtures in the Presence of Hot Surfaces, R. K. Kumar and G. W. Koroll; 94 Coupled RELAP5 and CONTAIN Accident Analysis Using PVM, K. A. Smith, A. J. Baratta, and G. E. Robinson; CONTROL AND INSTRUMENTATION: 109 Application of Fuzzy Logic in Nuclear Reactor Control Part I: An Assessment of State-of-the-Art, A. S. Heger, N. K. Alang-Rashid, and M. Jamshidi; DESIGN FEATURES: 122 Twenty-Third DOE/NRC Nuclear Air-Cleaning and Treatment Conference, R. R. Bellamy, J. J. Hayes, and M. W. First; ENVIRONMENTAL EFFECTS: 135 Atmospheric Dispersion and the Radiological Consequences of Normal Airborne Effluents from a Nuclear Power Plant, D. Fang, C. Z. Sun, and L. Yang; 142 Calculation of Distribution Coefficients for Radionuclides in Soils and Sediments, I. Puigdomenech and U. Bergstrom: OPERATING EXPERIENCES: 155 Reactor Shutdown Experience, Compiled by J. W. Cletcher; U.S. NUCLEAR REGULATORY COMMISSION INFORMATION AND ANALYSES: 158 Operating Experience Feedback Report—Reliability of Safety-Related Steam Turbine-Driven Standby Pumps Used in U.S. Commercial Nuclear Power Plants, J. R. Boardman; 166 Turbine Building Hazards, H. L Ornstein; RECENT DEVELOPMENTS: 169 Reports, Standards, and Safety Guides, D. S. Queener; 175 Proposed Rule Changes as of Dec. 31,1994; ANNOUNCEMENTS: 32 Harvard School of Public Health In-Place Filter Testing Workshop; 134 International Conference on Advances in the Operational Safety of Nuclear Power Plants; 193 30th Tennessee Industries Week; 193 DOE Technical Standards Program 1995 Workshop; 194 Multiphase Flow Experiments and Instrumentation; 180 The Authors; 185 Indexes to Nuclear Safety, Volumes 34 and 35.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Machine learning and atomic layer deposition: Predicting saturation times from reactor growth profiles using artificial neural networks

In this work, we explore the application of deep neural networks to the optimization of atomic layer deposition (ALD) processes. In particular, we focus on a one-shot optimization problem, where we try to predict the optimal dose time that leads to saturation everywhere in the reactor based on thickness values measured at different points of an ALD reactor after a single trial growth. In order to tackle this problem, we introduce a dataset designed to train neural networks to predict saturation times based on these inputs for a cross-flow ALD reactor. Here, we then explore the predictive ability of artificial neural networks of different depths and sizes using a separate testing dataset to evaluate their accuracies. The results obtained show that networks trained using stochastic gradient descent methods can accurately predict saturation times without requiring any additional information on the surface kinetics. This provides a viable approach to minimize the number of experiments required to optimize new ALD processes in a known reactor, and it highlights the way machine learning can be leveraged for thin film growth and manufacturing. While the datasets and training procedure depend on the reactor geometry, the trained neural networks provide a general surrogate model connecting thickness values and trial dose times with optimal saturation times that can be reused for different ALD processes within the same reactor.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Tracking Active Phase Behavior on Boron Nitride during the Oxidative Dehydrogenation of Propane Using Operando X-ray Raman Spectroscopy

Hexagonal boron nitride (hBN) is a highly selective catalyst for the oxidative dehydrogenation of propane (ODHP) to propylene. Using a variety of ex situ characterization techniques, the activity of the catalyst has been attributed to the formation of an amorphous boron oxyhydroxide surface layer. The ODHP reaction mechanism proceeds via a combination of surface mediated and gas phase propagated radical reactions with the relative importance of both depending on the surface-to-void-volume ratio. Here we demonstrate the unique capability of operando X-ray Raman spectroscopy (XRS) to investigate the oxyfunctionalization of the catalyst under reaction conditions (1 mm outer diameter reactor, 500 to 550 °C, P = 30 kPa C 3 H 8 , 15 kPa O 2 , 56 kPa He). We probe the effect of a water cofeed on the surface of the activated catalyst and find that water removes boron oxyhydroxide from the surface, resulting in a lower reaction rate when the surface reaction dominates and an enhanced reaction rate when the gas phase contribution dominates. Computational description of the surface transformations at an atomic-level combined with high precision XRS spectra simulations with the OCEAN code rationalize the experimental observations. Finally, this work establishes XRS as a powerful technique for the investigation of light element-containing catalysts under working conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Ceramic reinforced zirconium alloy nuclear fuel cladding with intermediate oxidation resistant layer

The invention relates to compositions and methods for coating a zirconium alloy (e.g., ceramic-containing) cladding tube for use with fuel rods in a nuclear water reactor. The coating includes an intermediate oxidation resistant layer and a SiC containing layer at least partially deposited on the intermediate oxidation resistant layer. The SiC containing layer can include a plurality of fibers. The SiC containing layer may also be on the outer surface of end plugs. The invention provides improved capability for the zirconium alloy cladding to withstand normal and accident conditions in the nuclear water reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Catalytic membrane reactor, methods of making the same and methods of using the same for dehydrogenation reactions

A catalytic membrane reactor and methods of operating and producing the same are provided that efficiently produces highly pure hydrogen (H2) from ammonia (NH3) as well as operates according to other chemical conversion processes. In one embodiment, a tubular ceramic support made from porous yttria-stabilized zirconia has an outer surface that is impregnated with a metal catalyst such as ruthenium and then plated with a hydrogen permeable membrane such as palladium. An inner surface of the ceramic support is impregnated with cesium to promote conversion of ammonia to hydrogen and nitrogen (N2). The resulting catalytic membrane reactor produces highly pure hydrogen at low temperatures and with less catalytic loading. Therefore, ammonia can be used to effectively transport hydrogen for use in, for example, fuel cells in a vehicle.

Way, James Douglas↗
DOE OSTI2024

On a High-Mirror Stellarator Reactor Exploratory Concept With Neutrons Concentrated on Centrifuge Liquids

In the framework of fusion energy research based on magnetic confinement, stellarators allow numerous degrees of freedom for the design of the magnetic trap and plasma shape. Taking advantage of these features, some plasma shapes might benefit several of the many integrated elements involved in commercial fusion reactors, like, e.g., decreasing the number, mass and complexity of replaced activated in-vessel components (IVC) (i.e., by using liquids), extraction of large power, tritium generation, and remote maintenance. Certainly, free-surface liquid materials were proposed for tokamaks and field-reversed configuration (FRC) to try to improve some of such elements, i.e., in advanced power extraction (APEX) studies. Some reactor-relevant quasi-isodynamic (QI) magnetic configurations exhibit a relatively straight sector of plasma and high magnetic mirror. The combination of those elements and possibilities in a single stellarator reactor concept might have some advantages, in spite of the uncertainties due to the current low technological readiness level (TRL). The proposed and studied reactor concept is based on a vacuum vessel having short curved sectors and longer wide cylindrical sectors, which encloses a high-mirror low-vertical-excursion magnetic configuration, and swirling liquids or rotating cylinders, which centrifuge molten Li salts located at the low field region. Thus, the molten salts (if possible covered by a thin layer of liquid lithium) would be located on the internal perimeter of the cylinder, to act as particle exhaust (except for helium), neutron power extractor, and tritium breeder. The high-mirror feature tries to concentrate the neutron power at the cylindrical sectors, which might avoid using breeding materials at the curved sectors. The different elements of the concept are exploratorily studied and defined, and the difficulties assessed.

centrifuge↗
DOE OSTI2020

Using Resin to Reduce Silica in Borated Fluid - 20072

The Electric Power Research Institute (EPRI) strongly recommends the concentration of silica in the reactor coolant be limited, potential ingress be carefully controlled, and frequently monitored to assess potential silica deposits on fuel cladding surfaces. Boraflex is a product with silicone rubber encasing a neutron absorber for criticality control, and it was installed in the majority of nuclear power plant spent fuel pools. Over time and in the presence of radiation, the silicone rubber lining degrades into silica (SiO{sub 2}) and hydrogen gas. Silica is somewhat soluble in water and spent fuel pool water communicates with other plant systems during refueling outages, leading to a buildup of silica in the reactor coolant and connected systems. Due to the prevalence of Boraflex racks in spent fuel pools, the presence of silica is a chronic nuclear industry concern. To address this concern, many nuclear plants have installed reverse osmosis skid systems to remove the silica from their spent fuel pools and, by extension, from reactor coolant. These skids are expensive to install and maintain. Arcadis personnel demonstrated that an iron-impregnated resin could be used to remove silica from borated systems without impacting the water quality. The resin was readily available, inexpensive, and easy to install in existing plant equipment. During a nuclear power plant's refueling outage the iron-impregnated resin proved to be effective in reducing the need for feed and bleed operations, with concurrent cost savings and reduction in required outage water management activities. Thus, the following savings were realized: - Eliminated the need to purchase, install, and maintain a reverse osmosis system avoiding more than $10 million in up-front capital cost and ongoing operating and maintenance costs. - Removed 9.57 kilograms (21 pounds) of silica dioxide from the primary system fluid. - Reduced the volume of feed and bleed from 70,000 gallons (2.65 E+05 liters) to 35,000 gallons (1.32 E+05 liters). - Saved $380,000 in water production and disposal costs. (author)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Modeling of SRS Aluminum-clad Spent Nuclear Fuel in Standard DOE Sealed Canisters

At the Savannah River Site (SRS), approximately 7 MTHM of aluminum-clad spent nuclear fuel is currently in wet storage at L-basin. A significant portion of this fuel is slated to be dried and sealed in DOE standard canisters for long-term storage. This report will focus on a few fuel types, which should bound all other fuel stored at SRS. These consist of the reference fuel assembly, the MURR fuel and the HFIR fuel. These bound a hypothetical maximum scenario for MTR box fuel, a maximum for decay heat in an assembly, and a maximum for the aluminum surface area, respectively. The geometry for the packages were created from DOE specifications for storage of each of the fuels. As long as the minimum time from reactor discharge to sealed storage is 3 years, then the highest temperatures which occur within the sealed canisters do not exceed 100° C for all scenarios considered here. In the geometry considered, while the HFIR fuel has a large surface area, the packaging configuration leaves large void areas, such that the aluminum surface to free volume ratio is about 30% less than an ATR or MURR packaging configuration.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Drying of Spent Nuclear Fuel: Considerations and Examples

A recently revised American Society for Testing and Materials consensus standard guide for drying of spent nuclear fuel (SNF) provides considerations and guidance for preparing SNF for its safe storage in a sealed dry storage system. The standard discusses (1) needs for drying, (2) techniques to dry, and (3) demonstration of adequate dryness. No specific approach is prescribed since the effective techniques and needs for drying depend on the specifics of the fuel and dry storage system. Here, this paper discusses these topics using examples for both Zr-alloy-clad commercial SNF and for aluminum-alloy-clad research reactor SNF. Residual water can include free water (liquid and/or vapor), physisorbed water bound to internal surfaces, and chemisorbed water incorporated into surface films, such as (oxy)hydroxides. The potential impacts of these residual waters are corrosion/oxidation, radiolytic breakdown into gaseous and/or reactive species, and canister pressurization. For commercial SNF, inadvertent free water, even up to large amounts (e.g., 10+ mol), is not predicted to cause adverse corrosion degradation, except possible fuel oxidation for breached SNF. For aluminum-clad SNF, the production of radiolytic hydrogen with contribution from the chemisorbed water in its hydrated oxides is a primary consideration. For both SNF systems, canister pressurization is predicted to be well within the canister design, and flammability would not pose a safety concern using an oxygen limit of 5 vol % criterion. (Flammability control can be achieved by limiting either hydrogen or oxygen, and an oxygen limit is expected to be easier to meet in the presence of radiolytic H 2 generation.) The two primary technologies for SNF drying, vacuum drying and forced-gas dehydration, are described herein, and drying tests and campaigns using these methods are cited. Dryness criteria and the methods used to detect and measure residual (free) water are also discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Strategic Survey of Antineutrino-based Nonproliferation Technologies

Antineutrinos carry approximately 3% of the total energy released in fission processes. As a consequence, nuclear energy production provides by far the brightest antineutrino sources on Earth. Antineutrino interactions with ordinary matter are weak and these particles cannot be shielded, making them an ideal signature of fissioning systems. However, the same property makes antineutrinos difficult to detect. Antineutrino detection technologies have matured in recent years, and emerging detection approaches warrant further investment. For near-field applications, the major enabling technological advancement, reported in 2018, is the conclusive detection of the antineutrino spectrum in segmented detectors operating at the surface with minimal shielding. For far-field applications, the highlights are the routine detection of reactor antineutrinos at hundreds of kilometer standoff in the kiloton-scale KamLAND and Borexino liquid scintillator detectors, and in particular the observation of the residual South Korean reactor antineutrino flux in KamLAND following the Fukushima disaster that led to shutdown of reactors in Japan

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Non-Equilibrium Synthesis of Semiconductor Alloys for Energy Applications

This project explores the synthesis under equilibrium/non-equilibrium conditions of semiconductor alloys critical to SSL to impose top-down influence on the formation of atomic-scale microstructures. A plasma-enhanced MOCVD (PE-MOCVD) technique is employed, in which plasma generated within the low-pressure reactor environment introduces additional energy that is delivered to the gas-phase reactants and growth surface, allowing relatively low substrate temperatures to be maintained, rapidly switching the crystal-growth environment into a non-equilibrium state. The project coordinates on-going work at National Renewable Energy Laboratory (NREL) that addresses order/disorder Al x In 1-x P (AlInP) confinement structures, which are predicted to surpass the power-conversion efficiency of current materials used for red/amber LEDs as components of so-called color-mixed LEDs, which integrate multiple LEDs in a single device for improved color rendering. Ordering, phase separation, and strain relaxation are central to this technology. During growth, each spontaneous process could be suppressed or enhanced on demand by application of plasma as an additional handle. This technique could have broader applications to other energy technologies, such as photovoltaics.

14 SOLAR ENERGY↗
DOE OSTI2022

Thermal expansion of plasma-exposed tungsten

We report results from a systematic analysis of thermal expansion of plasma-exposed tungsten based on molecular-dynamics simulations using models of tungsten with distributions of helium (He) bubbles in the tungsten matrix. We distinguish between two approaches of filling the bubbles with He, where the amount of He in the bubble can or cannot vary with temperature. In the former case, the thermal expansion coefficient decreases monotonically with the porosity and He content of the tungsten matrix, while in the latter case, the thermal expansivity increases monotonically with increasing porosity and He content. The latter condition, where the He content in the bubble is determined at the implantation temperature and remains constant with varying temperature in the tungsten matrix, is consistent with He species transport in tungsten used as a plasma-facing component (PFC) in nuclear fusion reactors and implies the development of biaxial compressive thermal strains in the PFC material that contribute to accelerating the growth of a nanostructure on PFC tungsten surfaces. Furthermore our analysis advances the fundamental understanding of thermal expansion in PFC tungsten and contributes to the development of a thermophysical property database for properly incorporating effects of realistic heat loads into modeling the dynamical response of PFC tungsten under fusion reactor operating conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Compositionally-driven surface nanostructuring on refractory compositionally complex alloys under low energy helium bombardment

Additive manufacturing enables user-defined control of the compositional complexity, opening new design spaces for complex concentrated alloys (CCAs). Refractory CCAs may offer enhanced performance in the divertor region of a fusion reactor environment where plasma-facing materials will be subject to high temperatures, low energy He and D particles, and 14 MeV neutrons. In this work, specimens with the nominal composition of NbTaMoTi, NbTaMo, NbTaTi, and NbTa were fabricated via directed energy deposition (DED) then bombarded with 40 eV He ions to a fluence of 2x10 26 m −2 at ∼ 1000 K. Post irradiation, the surface morphology and composition were examined with electron microscopy and x-ray photoelectron spectroscopy to offer information on the spatial distribution of surface nano-structuring. Sub-surface He bubbles driving the nano-structuring were examined with electron microscopy techniques. Analysis indicates the local composition directly influences the He bubble and tendril size, while the region with the highest complexity showed the shortest nano-structuring. Molecular Dynamics simulations complement the experimental results, showing comparable helium bubble growth and migration as a function of compositional complexity. This work demonstrates the compositional dependence of surface nanostructure formation of compositionally complex alloys, important for future design of complex plasma facing materials in fusion reactors.

Complex concentrated alloys↗
DOE OSTI2023

Writing the Programs of Programmable Catalysis

It has long been known that non-steady state and periodic catalytic reactor operation in terms of temperature, pressure, and composition can lead to higher overall productivity and/or product selectivity than the best steady operation. Recently, the emergence of catalysts whose intrinsic properties can be made to oscillate with time, introduces advanced forcing capabilities that can be “programmed” into the catalysts to broaden the scope and applicability of periodic operation to surface chemistry. In this work, an algorithmic approach is implemented to significantly accelerate the discovery and optimization of periodic steady states of catalytic reactors. Decomposition of complex dynamics into fundamental mechanistic fast–slow steps is seen to improve conceptual understanding of the relationship between binding energy oscillation protocols and overall catalytic rates. Finding structured forcing protocols, optimally tailored to the multiple time scales of a given individual mechanism, requires an efficient search of high-dimensional parameter spaces. Here, this is enabled here through active learning (Bayesian optimization, enhanced by our proposed Bayesian continuation). Implementation of these methods is shown to accelerate the evaluation of catalyst programs by up to several orders of magnitude. Faster screening of programmable catalysts to discover periodic steady states enables the optimization of catalytic operating protocols and thus opens the possibility for catalyst engineering based on optimal forcing programs to control rate and product selectivity, even for complex multistep catalytic mechanisms.

catalysis↗
DOE OSTI2021

Reactor scale simulations of ALD and ALE: Ideal and non-ideal self-limited processes in a cylindrical and a 300 mm wafer cross-flow reactor

Here, we have developed a simulation tool to model self-limited processes such as atomic layer deposition (ALD) and atomic layer etching inside reactors of arbitrary geometry as well the output of in situ quartz crystal microbalance and mass spectrometry. We have applied this model to two standard types of cross-flow reactors: a cylindrical tube reactor and a model 300 mm wafer reactor, and explored both ideal and nonideal self-limited kinetics. The model results are in agreement with experimental results and analytic expressions obtained using a simple plug-flow model for the cylindrical tube reactor. We also extended the simulations to consider two nonideal self-limited processes: soft-saturating processes characterized by a slow reaction pathway and processes where surface by-products can compete with the precursor for the same pool of adsorption sites. Our results show that it is possible to have a self-limited process with saturated yet inhomogeneous growth profiles due to the competition of reactor by-products. This is in agreement with experimental observations for titanium dioxide ALD from titanium tetraisopropoxide and titanium tetrachloride precursors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Results of the CHF-SERTTA In-Pile Transient Boiling Experiments at TREAT

To advance the current understanding of heat transfer between nuclear fuel rod cladding and the surrounding coolant under transient scenarios involving critical heat flux (CHF), the CHF-Static Environment Rodlet Transient Test Apparatus (CHFSERTTA), an in-pile experiment, was developed for and irradiated in the Transient Reactor Test (TREAT) facility at Idaho National Laboratory. The CHF-SERTTA experiment consists of a hollow, borated stainless steel rod submerged in a static water pool. The rod, heated via the (n, a) reaction in boron-10, was designed for investigating in-pile transient heat transfer between the rod surface and the coolant, avoiding the complexity of including the heat transfer between the fuel, gas gap, and cladding in typical light-water reactor (LWR) fuel rods. The instrumentation package for CHF-SERTTA focused on capturing those data that best describe the heat transfer behaviour between the rod and coolant. This paper outlines the CHFSERTTA experiment design and presents the initial results of the experiment campaign.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗