Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface cracks”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

A New General Paradigm for Understanding and Preventing Li Metal Penetration through Solid Electrolytes

The use of lithium (Li) or sodium (Na) metal anodes together with highly ion-conductive solid electrolytes (SEs) could provide batteries with a step improvement in volumetric and gravimetric energy densities. Unfortunately, these SEs face significant technical challenges, in large part because Li and Na dendrites can penetrate through SEs, leading to short circuits. The ability of such a soft material (Li or Na metal) to penetrate through ceramic is surprising from the point of view of models widely used in the Li-battery field. We introduce a concept, new to the battery field, for preventing penetration of lithium dendrites through SEs by putting the SE surfaces into a state of residual compressive stress. For a sufficiently high compressive stress, cracks have difficulty forming, and cracks that do form are forced to close, inhibiting dendrite penetration. This approach is widely used to solve commercially important stress corrosion cracking problems in metals and static fatigue problems in ceramics and glasses (e.g., Gorilla Glass). However, the technique will not be useful for SEs if the Li-ion transport rate through a SE is substantially reduced when the SE is under compression. Our molecular dynamics calculations for Li-ion transport through a common SE demonstrate that the introduction of even very high residual compressive stresses (~10 GPa) has only a modest effect on Li-ion transport kinetics, suggesting that this approach is viable and capable of providing a new paradigm for developing high-performance and mechanically stable SEs.

25 ENERGY STORAGE↗
DOE OSTI2022

Understanding the Origin of the Nonpassivating Behavior of Si-Based Anodes during the Initial Cycles

In this contribution, we combined electrochemical cycling and X-ray photoelectron spectroscopy (XPS) to understand the nonpassivating behavior of the solid electrolyte interphase (SEI) on Si anodes during the first cycles. Based on galvanostatic measurements, we show that the irreversible capacity loss is reduced after the first cycle, and it stays almost constant from the second cycle onwards. XPS was used to determine the root causes of the Coulombic inefficiency, showing that the rate of decomposition of the organic solvents strongly decreased after the first cycle, whereas the rate of salt decomposition is almost unchanged between cycles. We determine that the inhibition of the decomposition reaction of the organic solvent is responsible for the lower Coulombic loss during the second electrochemical cycle in comparison to the first, whereas the nonpassivating behavior toward the salt decomposition is one of the main causes of capacity loss upon cycling. Here, we further revisit the role of cracking in contributing to capacity loss. Whereas high volumetric expansion remains an issue plaguing the performance of Si anodes, our chronoamperometry studies reveal that the SEI formed on Si anodes does not passivate even when the electrode is fully expanded, and no additional surface is exposed. Overall, our work establishes the need to address the chemical and electrochemical instability of the SEI on the Si anode in addition to the more notorious issue of cracking.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

SEM/EBSD Characterization of Baffle-Former Bolts Designated for High Energy X-ray Microscopy Studies at the Advanced Photon Source

This report documents the microstructural and surface characterization of two high-fluence baffle-former bolts (BFBs) harvested from a commercial pressurized water reactor (PWR) after nearly four decades of service. These bolts experienced extreme conditions including high neutron fluence, elevated temperatures, corrosive primary water, and sustained mechanical loads, all of which contribute to degradation mechanisms such as irradiation-assisted stress corrosion cracking (IASCC). Using scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD), the study assessed bulk and near-surface microstructures, grain boundary characteristics, and in-service oxide layers. The results revealed significant differences between bolts exposed to 41 dpa and 29 dpa, including differences in recrystallization extent, deformation structures, and oxidation morphology. These findings establish critical baseline data for integration with advanced synchrotron-based high-energy X-ray microscopy (HEXM) and computational crystal plasticity models. Ultimately, the work supports improved mechanistic understanding and predictive capability regarding the long-term performance of reactor core internal components.

Lach, Tim [Oak Ridge National Laboratory (ORNL), O↗
DOE OSTI2023

Effects of Accident Thermal Loading on In-Plane Shear Behavior of Steel-Plate Composite Walls

Structural walls in safety-related nuclear facilities are required to be designed for seismic and accident thermal (due to postulated high-energy pipe break events) loading combination. Current U.S. and international codes provide limited guidance for analysis and design of walls for this loading combination. This paper describes the experimental results and observations from tests conducted on a laboratory-scale (1:4 to 1:5) test unit representing steel-plate composite (SC) walls subjected to combined in-plane (seismic) and accident thermal loading. The test unit was subjected to surface temperatures of up to 450°F in combination with cyclic in-plane loading. Results of similar experiments recently conducted in Japan are also summarized (with surface temperatures up to 570°F). Surface heating combined with the low thermal conductivity and high specific heat of concrete resulted in nonlinear thermal gradients through the thickness of the specimens. These nonlinear thermal gradients and the associated self- or internal restraint led to extensive concrete cracking. This concrete cracking reduced the initial and secant stiffness of the specimens. The initial stiffness of the heated specimens reduced to 30 to 40% of the initial stiffness of the control (unheated) specimen. The secant stiffness of the heated specimens reduced up to 50% of the secant stiffness of the control (unheated) specimen. However, the in-plane shear strength of the heated SC specimens was still approximately 10 to 30% greater than the nominal in-plane shear strength calculated, for the limit state of steel plate von Mises yielding, using AISC N690 equations and measured material properties. Evaluation of the experimental results and observations suggests that the in-plane shear strength of SC walls subjected to typical accident surface temperatures (up to 570°F) can be estimated conservatively using the current provisions of AISC N690. The stiffness for accident thermal loading combinations can be considered to reduce from cracked composite stiffness at ambient temperature to fully cracked—that is, steel-only stiffness as the surface temperature increases up to typical accident value.

Construction & Building Technology↗
DOE OSTI2023

Effect of free surfaces on localized plastic deformation in single-crystal nickel containing helium bubbles and radiation-induced self-interstitial atom clusters

This paper presents molecular dynamics (MD) simulations of plastic deformation in single-crystal Ni models containing internal distributions of helium (He) bubbles and self-interstitial atom (SIA) clusters corresponding to experimental characterization of ex-service Inconel X-750 components. Here, we simulate single crystals with and without free surfaces at room temperature and 588K, the latter temperature corresponding to the Inconel X-750 service conditions. Both models are deformed under multiple slip to a maximum deviatoric strain of ~10 %. A dislocation slip band forms in the model without free surfaces, but not in the model with free surfaces. However, the latter exhibits nano-twin nucleation from surfaces. Helium (He) bubbles that overlap with a slip band or a nano-twinned region deform more severely than other bubbles in the model. Nevertheless, the bubbles do not link up and do not form configurations that resemble incipient cracks.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Surface coating by mechanofusion modulates bulk charging pathways and battery performance of Ni-rich layered cathodes

Ni-rich layered oxides as high-capacity battery cathodes suffer from degradation at high voltages. Here, we utilize a dry surface modification method, mechanofusion (MF), to achieve enhanced battery stability. The simplicity, high yield, and flexibility make it cost-effective and highly attractive for processing at the industrial scale. The underlying mechanisms responsible for performance improvement are unveiled by a systematic study combining multiple probes, e.g., 3D nano-tomography, spectroscopic imaging, in situ synchrotron diffraction, and finite element analysis (FEA). MF affects the bulk crystallography by introducing partially disordered structure, microstrain, and local lattice variation. Furthermore, the crack initiation and propagation pattern during delithiation are regulated and the overall mechanical fracture is reduced after such surface coating. We validate that MF can alter the bulk charging pathways. Such a synergic effect between surface modification and bulk charge distribution is fundamentally important for designing next-generation battery cathode materials.

25 ENERGY STORAGE↗
DOE OSTI2021

Mechanism and kinetics of light alkane dehydrogenation and cracking over isolated Ga species in Ga/H-MFI

The objective of this study is to examine the mechanisms and kinetics of C2H6 dehydrogenation and n-C4H10 dehydrogenation and cracking over isolated Ga species in Ga/HMFI and to compare these results to those reported previously for C3H8 dehydrogenation and cracking. C2H6 dehydrogenation is found to be catalyzed by both [GaH]2+ and [GaH2]+ cations at similar turnover frequencies. Rate measurements over Ga/H-MFI containing predominantly [GaH2]+ cations reveal that C2H6 dehydrogenation rates exhibit a Langmuir.Hinshelwood dependence on C2H6 partial pressure at elevated temperatures (>730 K), consistent with the involvement of chemisorbed [C2H5.GaH]+ species. The reaction kinetics suggest that C2H6 dehydrogenation proceeds via heterolytic C-H cleavage of adsorbed C2H6 by [GaH2]+ cations to form H2 and [C2H5-GaH]+ species, which further decompose via β-hydride elimination to form C2H4. By contrast, C4H10 dehydrogenation and both terminal and central cracking are catalyzed exclusively by [GaH]2+ cations. All three reactions exhibit a Langmuir-Hinshelwood dependence on C4H10 partial pressure and are inhibited by H2. Ratios of dehydrogenation to cracking (total) and terminal to central cracking are approximately independent of C4H10 partial pressure consistent with the involvement of a common C4H10-derived surface intermediate. The observed reaction kinetics are consistent with an alkyl-mediated mechanism occurring over [GaH]2+, analogous to that reported previously for C3H8 dehydrogenation/cracking over Ga/H-MFI (Phadke, N. M.; et al. J. Am. Chem. Soc. 2019, 141, 1614-1627). The mechanism proceeds via facile, heterolytic dissociation of adsorbed C4H10 to form [C4H9-GaH]+-H+ cation pairs via methyl C-H-activated pathways. Dehydrogenation then proceeds via β-hydride elimination, respectively, forming butene, while terminal and central cracking proceed via C-H-activated H+ attack. Methylene activation was also considered but found to occur at a significantly lower rate. Theoretical analysis of the proposed reaction pathways leads to apparent activation enthalpies in good agreement with values extracted from the measured kinetics, thereby supporting the proposed pathways and the roles of [GaH]2+ and [GaH2]+ cations in the dehydrogenation and cracking of light alkanes on Ga/H-MFI.

Phadke, NM↗
DOE OSTI2024

Carboxylating Elastomer via Thiol‐Ene Click Reaction to Improve Miscibility with Conjugated Polymers for Mechanically Robust Organic Solar Cells with Efficiency of 19%

Abstract Incorporating flexible insulating polymers is a straightforward strategy to enhance the mechanical properties of rigid conjugated polymers, enabling their use in flexible electronic devices. However, maintaining electronic characteristics simultaneously is challenging due to the poor miscibility between insulating polymers and conjugated polymers. This study introduces the carboxylation of insulating polymers as an effective strategy to enhance miscibility with conjugated polymers via surface energy modulation and hydrogen bonding. The carboxylated elastomer, synthesized via a thiol‐ene click reaction, closely matches the surface energy of the conjugated polymer. This significantly improves the mechanical properties, achieving a high crack‐onset strain of 21.48%, surpassing that (5.93%) of the unmodified elastomer:conjugated polymer blend. Upon incorporating the carboxylated elastomer into PM6:L8‐BO‐based organic solar cells, an impressive power conversion efficiency of 19.04% is attained, which top‐performs among insulating polymer‐incorporated devices and outperforms devices with unmodified elastomer or neat PM6:L8‐BO. The superior efficiency is attributed to the optimized microstructures and enhanced crystallinity for efficient and balanced charge transport, and suppressed charge recombination. Furthermore, flexible devices with 5% carboxylated elastomer exhibit superior mechanical stability, retaining ≈88.9% of the initial efficiency after 40 000 bending cycles at a 1 mm radius, surpassing ≈83.5% for devices with 5% unmodified elastomer.

Chemistry↗
DOE OSTI2025

Structure-dependent mechanisms for plastic degradation in the marine environment

The visible and invisible accumulation of waste plastic in our oceans is a consequence of rapidly increasing inputs and very slow degradation rates. In general, this combination of effects results in long residence times. Nevertheless, the abiological degradation rate of a specific synthetic plastic varies widely, depending on its structural characteristics at the molecular, mesoscopic, and macroscopic levels. This chapter summarizes factors that determine these rates of degradation, and describes their principal mechanisms, for several of the major types of waste plastic found in the oceans. Mechanical forces cause cracking and flaking that break macroplastics into microplastics and even smaller fragments with increasing surface-to-volume ratios. Chemical degradation rates increase with surface area, influenced by intrinsic variations in crystallinity and the presence of additives, as well as extrinsic factors such as temperature, pH, and UV light intensity. Since polyolefin-based plastics are less dense than seawater and lack hydrolysable bonds in their polymer backbones, they accumulate close to the surface of the ocean where photo-oxidation is the principal cause of C–C bond cleavage in the polymer backbone. In contrast, polyesters and polyamides are denser than seawater and they sink, experiencing less exposure to solar irradiation. However, they can also degrade by slow hydrolysis of the C–O or C–N bonds intrinsic to the polymer structures.

Maciulis, Nicholas A.↗
DOE OSTI2020

Making ultrastrong steel tough by grain-boundary delamination

Developing ultrahigh-strength steels that are ductile, fracture resistant, and cost effective would be attractive for a variety of structural applications. We show that improved fracture resistance in a steel with an ultrahigh yield strength of nearly 2 gigapascals can be achieved by activating delamination toughening coupled with transformation-induced plasticity. Delamination toughening associated with intensive but controlled cracking at manganese-enriched prior-austenite grain boundaries normal to the primary fracture surface dramatically improves the overall fracture resistance. As a result, fracture under plane-strain conditions is automatically transformed into a series of fracture processes in “parallel” plane-stress conditions through the thickness. The present “high-strength induced multidelamination” strategy offers a different pathway to develop engineering materials with ultrahigh strength and superior toughness at economical materials cost.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thermal and Deposition Modeling of the Canister Deposition Field Demonstration

This report provides initial thermal and deposition modeling results of the spent nuclear fuel (SNF) storage system planned for use in the Canister Deposition Field Demonstration (CDFD). The goal of the CDFD testing is to collect deposition measurements on the surface of the dry shielded canister (DSC) to aid in chloride-induced stress corrosion crack (CISCC) research. Ideally this testing will occur in a marine coastal environment but at the time of this report no official site has been selected. The CDFD will use the NUHOMS ® Advanced Horizontal Storage Module – High Seismic (AHSM-HS) with a 32PTH2 canister. The SNF assemblies will be replaced with electrical heaters. Canisters are currently being outfitted with these heaters and tested at Sandia National Laboratory (SNL). Thermal modeling was conducted to ensure the electrical heaters were representative of the temperature distribution found within a storage system with SNF. Deposition models were built to evaluate contaminant deposition on SNF canisters. The CDFD testing will help to validate these models, which will then be used to plan and inform on-site test programs and predictive models for the timing and occurrence of canister CISCC.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Thermal and Deposition Modeling Update for the Canister Deposition Field Demonstration

This report provides an update on the thermal and deposition modeling being performed in support of the Canister Deposition Field Demonstration (CDFD). The goal of the CDFD testing is to collect deposition measurements on the surface of the dry shielded canister (DSC) to aid in chloride-induced stress corrosion cracking (CISCC) research. Ideally, this testing will occur in a marine coastal environment, but at the time of this report, no official site has been selected. The CDFD plans to use the NUHOMS® Advanced Horizontal Storage Module – High Seismic (AHSM-HS) with a 32PTH2 canister. The spent nuclear fuel (SNF) assemblies will be mimicked with electrical heaters. Canisters are currently being outfitted with these heaters and tested at Sandia National Laboratories (SNL). Thermal modeling was conducted to ensure the electrical heaters are representative of the temperature distribution found within a storage system with SNF. Deposition models were also built to evaluate particulate deposition on SNF canisters. A preliminary site model was constructed to support a planned upcoming ambient aerosol characterization campaign.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Plasma surface ionization wave interactions with single channels

Abstract The study of plasma surface ionization waves (SIWs) in recent years has primarily focused on planar surfaces and periodic two dimensional structures. In application, substrates are likely to have non-planar morphology such as cracks, pores, and steps. Additionally, targets for the applications of medicine or catalysis may have targets with heterogeneous composition. This classification of targets are brought under the umbrella of complex interfaces. In this work, plasma SIWs were incident on a complex target consisting of a single channel cut into glass slides. The SIW velocities for the in-channel portion of the wave and radially propagating portion of the wave were tracked. It was found that surface wave velocities are not significantly affected by channel geometry, but primarily increase with pulse energy. A third propagation direction for the SIW is characterized in the azimuthal direction relative to the radial portion of the wave. Channel geometry is found to greatly effect the area treated by the plasma but not the propagation velocity of the surface wave. Surface wave morphology and the impact on application is also discussed. A simple model was introduced to understand the mechanisms behind SIW escape from a channel. It was found that the ratio of pulse energy to a geometry dependent minimum energy can predict the escape angle of a SIW from single channels.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Suppressing strain propagation in ultrahigh-Ni cathodes during fast charging via epitaxial entropy-assisted coating

Surface reconstruction and the associated severe strain propagation have long been reported as the major cause of cathode failure during fast charging and long-term cycling. Despite tremendous attempts, no known strategies can simultaneously address the electro-chemomechanical instability without sacrificing energy and power density. Here we report an epitaxial entropy-assisted coating strategy for ultrahigh-Ni LiNi x Co y Mn 1-x-y O 2 (x ≥ 0.9) cathodes via an oriented attachment-driven reaction between Wadsley-Roth phase-based oxides and the layered-oxide cathodes. Further, the high anti-cracking and anti-corrosion tolerances as well as the fast ionic transport of the entropy-assisted surface effectively improved the fast charging/discharging capability, wide temperature tolerance and thermal stability of the ultrahigh-Ni cathodes. Comprehensive analysis from the primary and secondary particle level to the electrode level using multi-scale in situ synchrotron X-ray probes reveals greatly reduced lattice dislocations, anisotropic lattice strain and oxygen release as well as improved bulk/local structural stability, even when charging beyond the threshold state of charge (75%) of layered cathodes. Layered Ni-rich oxide cathodes are susceptible to challenges with surface reconstruction and strain propagation, limiting their cyclability. The authors propose a solution involving oriented attachment-driven reactions, utilizing Wadsley-Roth nanocrystals and layered oxide to induce an epitaxial entropy-assisted coating, effectively addressing these issues.

25 ENERGY STORAGE↗
DOE OSTI2021

An investigation into the effects of cyclic strain rate on the high cycle and very high cycle fatigue behaviors of wrought and additively manufactured Inconel 718

Additive Manufacturing (AM) has increasingly been used to fabricate parts in aerospace applications, which may require service lives beyond ten-million cycles due to the imposed high loading frequencies. Understanding the very high cycle fatigue (VHCF) behavior of these additive manufactured (AM) parts is an important step towards their design and qualification processes. This study focuses on the high cycle fatigue (HCF) and VHCF behaviors of both wrought and laser beam-powder bed fusion (LB-PBF) fabricated Inconel 718 in machined/polished surface condition, emphasizing on the influence of test frequency (i.e., cyclic strain rate). Uniaxial, fully-reversed force- and stress-controlled fatigue tests were conducted utilizing a servo-hydraulic and an ultrasonic test system operating at 5 Hz and 20 kHz, respectively, on wrought as well as LB-PBF vertically and diagonally built specimens. Fatigue cracks in the majority of the specimens were found to initiate from intra-granular slip bands near or at the surface, which gives rise to strong anisotropy in fatigue resistance in LB-PBF specimens due to the presence of columnar grains along the build directions. Longer fatigue lives were obtained at 20 kHz, which was ascribed to possibly lower-than-intended stresses applied in the ultrasonic tests. The corrected stress-life fatigue data at 20 kHz were found to converge to the one obtained from conventional testing at 5 Hz, implying no effect of cyclic strain rate on the fatigue behavior of Inconel 718 regardless of the fabrication process. The findings of this work confirm the use of ultrasonic fatigue testing to expedite generation of AM materials data to keep up with the current demand; however, the applied stress may need to be corrected.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Propagation of Cryogenic Thermal Fractures from Unconfined PMMA Boreholes

In cryogenic fracturing, a rock surface exposed to cryogenic fluids undergoes a large thermal gradient, and the resultant local tensile stress overcomes rock strength and initiates fractures. This study investigates the development of cracks generated from the cryogenic treatment of a borehole under no external confining stress on specimens. The experiments were performed on transparent PMMA specimens to observe fracture proliferation around boreholes. Liquid nitrogen was flowed through the boreholes to cool the borehole surface. The results show that initial fracture growth is characterized by abrupt starts and stops, and as the fracture propagates outward, the growth appears more continuous. In an early stage, horizontal/radial fractures and vertical fractures are the defining patterns. Horizontal fractures tend to be separated by a specific exclusion distance (i.e., spacing between cracks). While distinct horizontal/vertical fractures and exclusion distance manifest themselves at an early stage, fractures resulting from fracture interactions and curvatures can develop into complex shapes at later stages. Cryogenic thermal loading induces distinctively curved fractures. The tendency of curvature may prevent greater penetration. An increase in the borehole pressure during liquid nitrogen flow, however, can lessen fracture tortuosity and facilitate radial propagation. A high flow pressure and rate are also advantageous in that they accelerate cooling and fracture propagation.

42 ENGINEERING↗
DOE OSTI2021

Piezoelectric response and failure behavior of cement paste under external loading

We study the elastic behavior and rupture mechanism of Calcium Silicate Hydrates (C-S-H) in response to tensile loading. For the three tensile axes, initial defects are spotted in the interlayer regions. However, the crack propagation is rather different depending on the axis of tensile. The cup-and-cone failure surface shows the ductile feature of C-S-H in the x and y directions; while the devastating rupture mode confirms the brittle feature of C-S-H in the z direction. Piezoelectricity was investigated using the charge fluctuation method. The polarization variation in response to small strain was also investigated and piezoelectric coefficients were derived. Furthermore, dependence of elastic and piezoelectric properties over external pressure was analyzed. Results reveal an improvement of the mechanical properties and the ultimate strength especially in the z direction; whereas the non-piezoelectricity remains unchanged despite the rearrangement of atoms induced by the external applied pressure.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Summary of Alloy 617 and Alloy 709 Elevated Temperature Crack Growth Test Results from the Planned FY24 Crack Growth Test Activities

This report covers the results from crack growth rate testing performed at Idaho National Laboratory in the fiscal year 2024. It includes two creep crack growth rate tests and two creep-fatigue crack growth rate tests. Results are shown for each of these tests, included crack growth measured during the test using direct current potential drop, and measurements based off of the fracture surface. Load line displacement, as well as load, were also collected during the tests. Detailed analysis of the results will continue into the next fiscal year, however, a number of potential improvements to the equipment and testing procedures were identified that will increase testing reliability and throughput, as well as decrease complications with the analysis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗