Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solid modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Use of Several Thermal Analysis Techniques to Study the Cracking of an Nitrile Butadiene Rubber (NBR) Insulator on the Booster Separation Motor (BSM) of the Space Shuttle

Two different vendor rubber formulations have been used to produce the silica-filled NBR insulators for the BSM used on both of the Solid Rocket Boosters (SRBs) of the Space Shuttle. A number of lots of the BSM insulator in 1998-99 exhibited surface cracks and/or crazing. Each insulator is bonded to the BSM aluminum aft closure with an epoxy adhesive. Induced insulator stresses from adhesive cure are likely greatest where the insulator/adhesive contour is the greatest, thus showing increased insulator surface cracking in this area. Thermal analysis testing by Dynamic Mechanical Analyzer (DMA) and Thermomechanical Analysis (TMA) was performed on one each of the two vendor BSM insulators previously bonded that exhibited the surface cracking. The TMA data from the film/fiber technique yielded the most meaningful results, with thin insulator surface samples containing cracks having roughly the same modulus (stiffness) as thin insulator bulk samples just underneath.

Wingard, Charles D.↗
NASA NTRS2001

Compatibility Testing of Non-Metallic Materials for the Urine Processor Assembly (UPA) of International Space Station (ISS)

In the International Space Station (ISS), astronauts will convert urine into potable water with the Urine Processor Assembly (UPA). The urine is distilled, with the concentrated form containing about 15% brine solids, and the dilute form as a blend of pre-treated urine/wastewater. Eighteen candidate non-metallic materials for use with the UPA were tested in 2000 for compatibility with the concentrated and dilute urine solutions for continuous times of at least 30 days, and at conditions of 0.5 psia pressure and 100 F, to simulate the working UPA environment. A primary screening test for each material (virgin and conditioned) was dynamic mechanical analysis (DMA) in the stress relaxation mode, with the test data used to predict material performance for a 10-year use in space. Data showed that most of the candidate materials passed the compatibility testing, although a few significant changes in stress relaxation modulus were observed.

Wingard, Charles Doug↗
NASA NTRS1999

Structural Evaluation of the RSRM Nozzle Replacement Adhesive

This paper describes the structural performance evaluation of a replacement adhesive for the Reusable Solid Rocket Motor (RSRM) nozzle utilizing finite element analysis. Due to material obsolescence and industrial safety issues, the two current structural adhesives, EA 913 and EA 946 are to be replaced with a new adhesive. TIGA 321. The structural evaluation in support of the adhesive replacement effort includes residual stress, transportation, and flight analyses. Factors of safety are calculated using the stress response from each analysis. The factors of safety are used as the limiting criteria to compare the replacement adhesive against the current adhesives. Included in this paper are the analytical approach, assumptions and modeling techniques as well as the results of the evaluation. An important factor to the evaluation is the similarity in constitutive material properties (elastic modulus and Poisson's ratio) between TIGA 321 and EA 913. This similarity leads to equivalent material response from the two adhesives. However, TIGA 321 surpasses EA 913's performance due to higher material capabilities. Conversely, the change in stress response from EA 946 to TIGA 321 is more apparent: this is primarily attributed to the difference in the modulii of the two adhesives, which differ by two orders of magnitude. The results of the bondline evaluation indicate that the replacement adhesive provides superior performance than the current adhesives with only minor exceptions. Furthermore, TIGA 321 causes only a minor chance in the response of the phenolic and metal components.

Batista-Rodriguez, A.↗
DOE OSTI2024

Self-Organized Stress Distributions in Polycrystalline Materials [Dissertation]

Understanding stress distributions in solid materials is complicated by the fact that most materials are polycrystalline in nature, with each crystal having an elastically anisotropic reaction to force. This study is to gain a better understanding on how external forces placed on a polycrystal are related to internal reactions within and between the grains. The hypothesis is that the stress distribution in porous to fully dense materials are self-organized based on strong contacts between and within the individual grains created by force chains. Force chains, commonly known in loaded granular materials, and could be the phenomenon that connect micro to macro deformation. Scale bridging measurements conducted through Raman spectroscopy, Atomic Force Microscopy, and Digital Image Correlation will be used to create stress maps, modulus maps, and elastic strain maps across a variety of geological and pharmaceutical polycrystals. When possible, the resulting maps will be compared to current homogenization schemes and a full field models. Finite element modeling will be used to assess whether the patterning seen in the experimental map is a reasonable approximation based on the orientation data of the samples used. A minimum of three publications is projected to be accomplished focusing each on a different method to experimentally test and analyze stress distributions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

UHT-CAMANCHE: Ultra-High Temperature Ceramic Additively Manufactured Compact Heat Exchangers

The conceptual basis for this project is the convergence of advanced ultra-high temperature ceramic materials and additive manufacturing technologies to produce compact ceramic heat exchangers with complex internal flow path geometries. Task areas were broadly divided into materials and manufacturing development, heat exchanger design, component testing, and techno-economic analysis. Technical challenges included the design and commissioning of new test facilities, improving feature resolution and deposition rate of ceramic additive manufacturing techniques, establishing process-structure-property relationships in additively manufactured ultra-high temperature ceramics, and assessing high temperature materials compatibility in CO 2 environments. The primary candidate material evaluated in this work is a composite comprising zirconium diboride (ZrB2) with 30 vol. % silicon carbide (SiC) which was selected based on its desirable combination of high temperature mechanical properties, high thermal and electrical conductivities, and oxidation resistance. High solids loaded ZrB2-SiC pastes suitable for extrusion-based additive manufacturing were developed for the first time as part of this work. Materials compatibility studies indicate this material oxidizes in CO 2 to form a protective borosilicate scale which transforms to pure silica above 1000°C. Parts made by additive manufacturing displayed enlarged grain sizes produced by pressureless sintering as compared to hot-press sintering. Increases in microstructural coarseness have outsized effect on oxidation performance up to 1400°C due to incomplete oxidation of coarse large diameter SiC particles resulting in lower amounts of silica that apparently inhibit protective scale formation. Additive manufacturing as a forming technique did not appear to significantly affect thermal conductivity, hardness, or elastic modulus, though flexural strength was reduced by half or more as compared to traditionally hot-pressed materials. This effect was attributed to the presence of strength-limiting flaws (ca. 40 microns in size) originating from extrudate inhomogeneities that could potentially be eliminated with further process improvements. Attempts to attain economies of scale for production of multi-kilowatt scale heat exchangers by ceramic additive manufacturing proved difficult. Lack of automation and a modest extrusion rate while retaining fine feature resolution made the overall process labor intensive and limited experimental throughput. A number of full-scale components were taken through post-process heat treatments including drying, binder burnout, and sintering; however, none survived without significant flaws or cracks. Therefore, no operational data from a newly installed heat exchanger test loop were able to be obtained during the performance period. Continued research and development is recommended to improve economic feasibility of ceramic additive manufacturing by standardizing the use of advanced sensors, artificial intelligence, and automation tools to reduce associated labor costs and accelerate production rates. The materials and manufacturing techniques demonstrated in this work are likely to find applications in defense and energy applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Microstructural and infiltration properties of woven preforms during chemical vapor infiltration

Interface-resolved direct numerical simulations (DNSs) of chemical vapor infiltration (CVI) have been performed over a range of furnace-operating conditions (Thiele moduli) and for practical woven preform geometries. A level-set method is used to resolve the geometry of the initial preform at tow scale. The interface between the vapor and solid phase is then evolved in time through the entire CVI densification cycle, fully resolving the time-varying topology between the two phases. In contrast to previous level-set methods for CVI simulation, the physical reaction and diffusion processes govern the level-set movement in the current approach. The surface deposition kinetics is described by the usual one-step model. In this paper, the DNS data are used to study the evolving porosity, surface-to-volume ratio, and flow infiltration properties (permeability and effective diffusivities). Additionally, comparisons are made to popularly-assumed structure functions and the standard, Kozeny–Carmen porous media model commonly employed in modeled CFD simulations of CVI. The virtual DNS experiments reveal a Thiele modulus and preform geometry (fabric layup) dependence which the existing microstructural and infiltration models are not able to describe throughout the entire densification process. The DNS-based, woven geometry-specific correlations can be applied directly to mean-field, furnace-scale CFD simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mineral-Ground Micro-Fibrillated Cellulose Reinforcement for Polymer Compounds

Additive Manufacturing (AM) is quickly becoming a mainstream, energy efficient manufacturing technique for complex and custom components. ORNL has taken polymer AM into the next level with Big Area Additive Manufacturing (BAAM). However, we need to develop the strength of AM materials (specifically polymers) to satisfy the mechanical requirements of structural parts. Also, it is crucial that the developed process can easily be scaled up to have a significant impact in the manufacturing industry of US. Furthermore, renewable, bio-derived AM materials are desirable from a sustainability perspective. In the first phase of this project the mechanical properties of polymer AM components were significantly improved developing a micro fibrillated cellulose (MFC)-reinforced composite material system that is derived from biomass and compatible with BAAM. Unfortunately, the improvements were observed only with freeze-dried MFCs, and freeze-drying is a very slow process and is not industrially scalable. Furthermore, MFCs were not available in large quantities at low cost. However, FiberLean has reached 12,000 tons/year capacity (60,000 tons/year including the minerals). FiberLean offers MFCs at a scale and order of magnitude lower price than current market participants. With their recently developed novel (patent pending) drying process FiberLean can achieve over 50% solid content commercially. In the 2nd phase of the project, the original objective was to investigate this new novel drying process along with compounding with different formulations to optimize and adapt to large scale additive manufacturing. However, the compounded materials prepared via this approach were very brittle and demonstrated poor mechanical performance. Therefore, the project was focused more on a scalable chemical surface modification of MFCs to enable their drying via conventional oven process with minimal agglomeration and better dispersion in PLA polymer matrix. Fiberlean and ORNL have worked together in this project to develop mineral-ground microfibrillated cellulose (MFC) - reinforced additive manufacturing feedstock materials with significantly improved mechanical properties. Properly surface modified and dried Fiberlean cellulose microfibrils led to tensile strength increases up to ~40% and elastic modulus increases up to 70% with the addition of 30% MFC into PLA matrix. The work has led to a high impact journal article and a provisional patent. Opportunities for a follow up work to demonstrate the technology in large scale and application of it to AM applications are currently being searched.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Pressure-induced suppression of ferromagnetism in the itinerant ferromagnet LaCrSb 3

We have performed an extensive pressure-dependent structural, spectroscopic, and electrical transport study of LaCrSb 3 . The ferromagnetic phase (TC=120 K at p = 0 GPa) is fully suppressed by p = 26.5 GPa and the Cr moment decreases steadily with increasing pressure. The unit-cell volume decreases smoothly up to p = 55 GPa. We find that the bulk modulus and suppression of the magnetism are in good agreement with theoretical predictions, but the Cr moment decreases smoothly with pressure, in contrast to steplike drops predicted by theory. The ferromagnetic ordering temperature appears to be driven by the Cr moment.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Comparing the Effects of Side Chain Dipole–Dipole Interactions and Hydrogen Bonding on the Mechanical and Electrical Properties of Poly(3-hexylthiophene)

Poly(3-alkylthiophenes) are simple conjugated polymers with good electrical properties, but tend to be brittle, limiting their application. Here, we investigate how side chain modifications can improve their toughness without compromising their charge transport. Specifically, we compare a weak dipole–dipole interaction of ester groups with a stronger hydrogen-bonding interaction of the hydroxyl groups. Two copolymers with targeted 5 and 10 mol % ester-functionalized side chains were synthesized and hydrolyzed in the solid state to introduce hydroxyl groups. Both hydrolyzed polymers became insoluble in most organic solvents, providing a path to layer-by-layer solution processing. All polymers’ optical, thermal, structural, electrical, and mechanical properties were investigated. Optical spectroscopy revealed that functionalization at these low levels did not significantly affect aggregation or π–π stacking. Differential scanning calorimetry indicated reduced crystallinity in the functionalized copolymers compared to that of P3HT. Grazing-incidence wide-angle X-ray diffraction data showed that functionalization led to an increase in lamellar spacing without altering molecular orientation or π–π stacking. Mechanical testing highlighted that at the lower functionalization level, both ester and hydroxyl groups similarly enhanced toughness, suggesting that disorder, rather than the specific nature of the functional group, was responsible for these improvements. At the higher functionalization level, hydroxyl groups significantly increased the elastic modulus while also negatively impacting charge carrier mobility. This study suggests that with stronger hydrogen-bonding groups, only very small amounts can improve P3HT’s toughness. For a wider tunable range, it may be a better strategy to use weak interactions such as dipole–dipole interactions of ester groups.

36 MATERIALS SCIENCE↗
NASA NTRS1995

Electronic structure and the van Hove singularity scenario in high-T(sub c)H(g)Ba2CuO(4+delta) superconductors

The electronic structure and the hole concentrations in the high Tc superconductor HgBa2CuO(4+delta) (delta = O, 1) has been investigated by employing a first principles full potential self-consistent LMTO method with the local density functional theory. The scalar relativistic effects have been considered. The hole concentrations of the Cu-d and O-p(x,y) orbitals are seen to be larger for the HgBaCuO5 system than those of the HgBaCuO4 solid. However, the van Hove singularity (vHs) induced Cu-d and O-p peak which is seen to lie comparatively away and above the Fermi level in the delta = 1 system shifts towards the Fermi level in the delta = 0 system. Thus, the superconducting behavior appears to originate from the occurrence of the vHs peak at the Fermi level. The Fermi surface nesting area in the delta = 0 compound is seen to be larger than in the delta = 1 compound. The calculation reveals that the increase in pressure on the crystal enhances the hole concentrations but without showing any optimum value, On the other hand, the vHs peak approaches to-wards the Fermi level with pressure and crosses the Fermi surface near V/Vo approximately equals 0.625 (V and Vo are the crystal volumes at high and normal pressures, respectively). Our calculated value of the bulk modulus equal to 0.626 Mbar predicts the occurrence of this crossover at about 24 GPa which is in complete agreement with the experimental value. At this pressure the compound has maximum nesting area and self-doped behavior.

Agrawal, Bal K.↗
NASA NTRS1996

Solid State Synthesis and Properties of Monoclinic Celsian

Monoclinic celsian of Ba(0.75)Sr(0.25)Al2Si2O8 (BSAS-1) and B(0.85)Sr(O.15)Al2Si2O8 (BSAS-2) compositions have been synthesized from metal carbonates and oxides by solid state reaction. A mixture of BaCO3, SrCO3, Al2O3, and SiO2 powders was precalcined at approx. 900-940 C to decompose the carbonates followed by hot pressing at approx. 1300 C. The hot pressed BSAS-1 material was almost fully dense and contained the monoclinic celsian phase, with complete absence of the undesirable hexacelsian as indicated by x-ray diffraction. In contrast, a small fraction of hexacelsian was still present in hot pressed BSAS-2. However, on further heat treatment at 1200 C for 24 h, the hexacelsian phase was completely eliminated. The average linear thermal expansion coefficients of BSAS-1 and BSAS-2 compositions, having the monoclinic celsian phase, were measured to be 5.28 x 10(exp -6)/deg C and 5.15 x 10(exp -6)/deg C, respectively from room temperature to 1200 C. The hot pressed BSAS-1 celsian showed room temperature flexural strength of 131 MPa, elastic modulus of 96 GPa and was stable in air up to temperatures as high as approx. 1500 C.

Bansal, Narottam P.↗
DOE OSTI2024

Adhesion and Contact Aging of Acrylic Pressure-Sensitive Adhesives to Swollen Elastomers

Fluid-infused (or swollen) elastomers are known for their antiadhesive properties. The presence of excess fluid at their surface is the main contributor to limiting contact formation and minimizing adhesion. Despite their potential, the mechanisms for adhesion and contact aging to fluid-infused elastomers are poorly understood beyond contact with a few materials (ice, biofilms, glass). This study reports on adhesion to a model fluid-infused elastomer, poly(dimethylsiloxane) (PDMS), swollen with silicone oil. The effects of oil saturation, contact time, and the opposing surface are investigated. Specifically, adhesion to two different adherents with comparable surface energies but drastically different mechanical properties is investigated: a glass surface and a soft viscoelastic acrylic pressure-sensitive adhesive film (PSA, modulus ~25 kPa). Adhesion between the PSA and swollen PDMS [with 23% (w/w) silicone oil] retains up to 60% of its value compared to contact with unswollen (dry) PDMS. In contrast, adhesion to glass nearly vanishes in contact with the same swollen elastomer. Adhesion to the PSA also displays stronger contact aging than adhesion to glass. Contact aging with the PSA is comparable for dry and unsaturated PDMS. Moreover, load relaxation when the PSA is in contact with the PDMS does not correlate with contact aging for contact with the dry or unsaturated elastomer, suggesting that contact aging is likely caused by chain interpenetration and polymer reorganization within the contact region. Closer to full saturation of the PDMS with oil, adhesion to the PSA decreases significantly and shows a delay in the onset of contact aging that is weakly correlated to the poroelastic relaxation of the elastomer. Additional confocal imaging suggests that the presence of a layer of fluid trapped at the interface between the two solids could explain the delayed (and limited) contact aging to the oil-saturated PDMS.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Exploring the hardness and high-pressure behavior of osmium and ruthenium-doped rhenium diboride solid solutions

Rhenium diboride (ReB 2 ) exhibits high differential strain due to its puckered boron sheets that impede shear deformation. Here, we demonstrate the use of solid solution formation to enhance the Vickers hardness and differential strain of ReB 2 . ReB 2 -structured solid solutions (Re 0.98 Os 0.02 B 2 and Re 0.98 Ru 0.02 B 2 , noted as “ReOsB 2 ” and “ReRuB 2 ”) were synthesized via arc-melting from the pure elements. In-situ high-pressure radial x-ray diffraction was performed in the diamond anvil cell to study the incompressibility and lattice strain of ReOsB 2 and ReRuB 2 up to ~56 GPa. Both solid solutions exhibit higher incompressibility and differential strain than pure ReB 2 . However, while all lattice planes are strengthened by doping osmium (Os) into the ReB 2 structure, only the weakest ReB 2 lattice plane is enhanced with ruthenium (Ru). These results are in agreement with the Vickers hardness measurements of the two systems, where higher hardness was observed in ReOsB 2 . The combination of high-pressure studies with experimentally observed hardness data provides lattice specific information about the strengthening mechanisms behind the intrinsic hardness enhancement of the ReB 2 system.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Mechanical Properties of Permanent Foaming Fixatives for Deactivation and Decommissioning Activities

DOE-EM have identified an operational requirement for a fixative that can immobilize and/or encapsulate residual contamination in 3D void volumes (pipes, gloveboxes, waste containers, etc.) during D and D activities. Failure to safely and effectively immobilize residual contamination can: Put workers at risk, Contaminate the public and environment, Drive up operational costs. Commercial-off-the-shelf (COTS) polyurethane (PU) foams is one possible solution and is currently being investigated in collaboration with Savannah River National Lab (SRNL). Mechanical property testing will dictate how well PU foams can withstand physical stressors outlined in safety documents while immobilizing residual contamination. Results can provide a performance criteria for Section 5 of ASTM E3191: Standard Specification for Permanent Foaming Fixatives Used to Mitigate Spread of Radioactive Contamination. Polyurethanes consists of repeating units of urethanes which are produced from an exothermic reaction between a polyol (an alcohol with two or more hydroxyl groups in a molecule) and an isocyanate [2]. PUs consists of 3D cells that are formed by a blowing agent which is normally water. Water interacting with the isocyanate creates carbon dioxide and urea which contributes to cells' growth and expansion. The cross-linking between the polyol and isocyanate solidify the cell faces and walls. Micro scale properties that can influence mechanical properties include: Relative density (ratio between density of cellular material and density of the solid of which the cell walls are made of). Cells connectivity between edges and faces, and number of cells contact neighbors [3]. Whether a foam is open-celled or closed-celled. Closed-celled foams have a thin membrane that encloses each cell which can contribute to the stiffness of the foam. Incorporating fillers in the PU matrix like carbon-based nanoparticles in the form of expandable graphite (EG) can increase the thermal and mechanical performance [4]. When exposed to heat, EG produces a char layer that prevents heat and oxygen transfer which is known as intumescing. Mechanical performance is dependent on amount of EG loading since the cell sizes are linearly dependent on it. Overall, the rigid foams (I-R2) proved superior. SEM Analysis: I-R2 had the most consistent spherical sizes (average cell diameter: 489 μm), which enhance the relative density the most [5]. Tensile Testing Results: I-R2 experienced the largest breaking load (103.65 lbf) and stress (289.42 psi). I-R2 also had a higher Young's Modulus compared to R1 (2.99 ksi to 2.09 ksi). Compression Testing Results: I-R2 had the highest stress at 80% deflection (360.67 psi), load (1387.48 lbf) and modulus (3.92 ksi)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

High-Pressure Synthesis of Bulk Cobalt Cementite, Co 3 C

Transition metal carbides find use in a wide range of advanced high-resilience applications including high-strength steels, heat shields, and deep-earth drills. However, carbides of the mid-to-late transition metals remain difficult to isolate and characterize on account of their metastability, which precludes the preparation of high-quality bulk single crystal samples using traditional solid-state methods. Herein, we report a combined computational and experimental survey of the cobalt-carbon binary system under high pressures and demonstrate that pressure offers a route toward the bulk synthesis of the metastable cementite-type cobalt carbide, Co 3 C, which under ambient conditions can only be prepared in low-dimensional thin film or nanoparticle forms. First-principles calculations reveal two competitive low-energy stoichiometric phases under ambient pressures - Pnnm-Co 2 C (Fe 2 C-type) and Pnma-Co 3 C (Fe 3 Ctype) - consistent with the known low-dimensional phases that have been studied for their promising magnetic properties. However, the calculated formation enthalpy of Pnma-Co 3 C decreases steadily with the applied pressure, while that of Pnnm-Co 2 C increases. Here, we pursue these results using high-pressure laser-heated synthesis methods coupled with in situ X-ray diffraction and observe the formation of Pnma-Co 3 C above 4.8 GPa. We determine the experimental bulk modulus of Co 3 C to be K o = 237 GPa (K p = 4.0). First-principles calculations of the phonon modes in Co 3 C reveal dynamical instabilities at ambient pressure that are absent under compression. These results offer a promising new route for the synthesis of rare-earth-free magnets.

36 MATERIALS SCIENCE↗
NASA NTRS2004

Friction and Wear Characteristics of Cu-4Al Foil Bearing Coating at 25 and 650 degree C

The friction and wear performance of a Cu-4Al top foil coating has been investigated in Generation I foil air bearings. The copper alloy was applied by a novel deposition technique (ion diffusion) and the journal was coated with PS304, a plasma spray deposited high temperature composite solid lubricant coating. The ion diffusion coating process deposits a desirable smooth layer compared to other methods like cathodic arc deposition. The tribological performance of bearings with and without Cu-4Al foil coatings were evaluated through start-stop tests on an air bearing test rig at 25 and 650 C. The results indicate that the Cu-4Al assists during the initial break-in period, gives more stable friction performance with respect to temperature, and appears to prevent top foil wear at high temperature. The measured load capacity coefficient was 0.5, which was comparable to earlier testing of more advanced design Generation III bearings coated with standard cathodic arc deposited Cu-4Al. However, further studies are needed to determine if deeper penetration of the copper alloy into the foil would help make the transition in friction behavior from contact with the Cu-4Al coated foil to contact with the base foil material more gradual. Also, future work is recommended to assess the performance of ion diffusion coatings with different Cu-based alloy compositions and to investigate the effect the coating has on the elastic modulus of the foil material.

Stanford, Malcolm K.↗
DOE OSTI2021

Sound velocities in shock-compressed soda lime glass: Melting and liquid-state response

Longitudinal sound velocities (and elastic moduli) were determined in soda lime glass (SLG) at peak shock stresses ranging between 40 and 90 GPa. Laser interferometry was used to obtain particle velocity histories and sound velocities by impacting SLG samples on lithium fluoride (LiF) optical windows. In all experiments, the SLG response consists of a sharp jump to a constant state followed by a release wave. The measured longitudinal sound velocities and moduli showed a marked decrease between 52 and 58 GPa, providing experimental evidence for the transformation from an amorphous solid to a liquid in shock-compressed SLG. Furthermore, the stress threshold (~55 GPa) for melting in SLG is considerably lower than the threshold reported in shock-compressed fused silica (~72 GPa), showing the effect of network-modifying cations on the onset of melting. The relative values of sound velocities, shock velocities, and the Hugoniot slopes—between 58 and 90 GPa—are fully consistent with the thermodynamic response of a shock-compressed liquid. Using the experimental results, the Grüneisen parameter (Γ) values were determined for liquid SLG to 90 GPa and then used to provide the Mie-Grüneisen equation of state for liquid SLG.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Characterization of Annealing-Induced Phase Segregation in Composite Silicon Anodes for Li-ion Batteries

Silicon (Si) anodes present a promising alternative to graphite anodes for lithium-ion batteries (LIBs), as Si has a greater specific capacity. However, one major constraint is the volumetric change of Si during lithiation that results in an unstable solid-electrolyte interphase (SEI), so Si-containing electrodes require the use of various strategies to mitigate these effects and improve performance. One such solution is the use of Si nanoparticles (NPs) that maximize the surface area to volume ratio. Here, we discuss electrodes made with Si NPs treated with polyethylene oxide (PEO) (for improving dispersion during processing), conductive carbon NPs, and P84 polyimide binder which shows significant impacts of annealing treatment on improvements of active material utilization, first cycle efficiency, and capacity retention with extensive cycling . We used air-free argon ion polishing to create electrode cross sections and imaged through the electrode thickness using atomic force microscopy (AFM)-based nano-electrical characterization of scanning spreading resistance microscopy (SSRM), nano-mechanical characterizations of contact resonance and force volume (CR-FV), and scanning electron microscopy-based energy dispersive x-ray spectroscopy (SEM-EDS). Results show that the Si and conductive carbon segregate into phases with a distinctive carbon-rich banded morphology that surrounds the Si-rich phase during annealing. In pristine electrodes, the carbon- and SEI-rich bands exhibit a higher electronic conductivity and a lower elastic modulus than the Si active material phase. These structures, as well as distinct electronic and mechanical properties, remain during cycling, suggesting an improvement of electrical conduction pathways and a mechanical strain buffer for active Si material expansion during cycling. This phase separation may be a major factor in the improvement seen in electrochemical performance due to annealing. Additionally, our nm-scale and multi-mode characterizations provide a novel route for understanding and improving energy storage devices, which is advantageous due to the highly inhomogeneous of composite electrodes in nm-mm scales.

ENERGY STORAGE↗