Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “smoke plumes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Rapid evolution of aerosol particles and their optical properties downwind of wildfires in the western US

Abstract. During the first phase of the Biomass Burn Operational Project (BBOP) field campaign, conducted in the Pacific Northwest, the DOE G-1 aircraft was used to follow the time evolution of wildfire smoke from near the point of emission to locations 2–3.5 h downwind. In nine flights we made repeated transects of wildfire plumes at varying downwind distances and could thereby follow the plume's time evolution. On average there was little change in dilution-normalized aerosol mass concentration as a function of downwind distance. This consistency hides a dynamic system in which primary aerosol particles are evaporating and secondary ones condensing. Organic aerosol is oxidized as a result. On all transects more than 90 % of aerosol is organic. In freshly emitted smoke aerosol, NH4+ is approximately equivalent to NO3. After 2 h of daytime aging, NH4+ increased and is approximately equivalent to the sum of Cl, SO42, and NO3. Particle size increased with downwind distance, causing particles to be more efficient scatters. Averaged over nine flights, mass scattering efficiency (MSE) increased in ∼ 2 h by 56 % and doubled in one flight. Mechanisms for redistributing mass from small to large particles are discussed. Coagulation is effective at moving aerosol from the Aitken to accumulation modes but yields only a minor increase in MSE. As absorption remained nearly constant with age, the time evolution of single scatter albedo was controlled by age-dependent scattering. Near-fire aerosol had a single scatter albedo (SSA) of 0.8–0.9. After 1 to 2 h of aging SSAs were typically 0.9 and greater. Assuming global-average surface and atmospheric conditions, the observed age dependence in SSA would change the direct radiative effect of a wildfire plume from near zero near the fire to a cooling effect downwind.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2020

Radiative Heating Rate Profiles over the Southeast Atlantic Ocean during the 2016 and 2017 Biomass Burning Seasons

Marine boundary layer clouds, including the transition from stratocumulus to cumulus, are poorly represented in numerical weather prediction and general circulation models. Further uncertainties in the cloud structure arise in the presence of biomass burning carbonaceous aerosol, as is the case over the southeast Atlantic Ocean where biomass burning aerosol is transported from the African continent. As the aerosol plume progresses across the southeast Atlantic Ocean, radiative heating within the aerosol layer has the potential to alter the thermodynamic environment and therefore the cloud structure; however, limited work has been done to quantify this along the trajectory of the aerosol plume in the region. The deployment of the First Atmospheric Radiation Measurement Mobile Facility in support of the Layered Atlantic Smoke Interactions with Clouds field campaign provided a unique opportunity to collect observations of cloud and aerosol properties during two consecutive biomass burning seasons during July through October of 2016 and 2017 over Ascension Island (7.96 °S, 14.35 °W). Using observed profiles of temperature, humidity, and clouds from the field campaign, alongside aerosol optical properties from MERRA-2 as input for the Rapid Radiation Transfer Model, profiles of the radiative heating rate due to aerosols and clouds were computed. Radiative heating is also assessed across the southeast Atlantic Ocean using an ensemble of back trajectories from the Hybrid Single Particle Lagrangian Integrated Trajectory Model. Idealized experiments using the Rapid Radiation Transfer Model with and without aerosols and a range of values for the single scattering albedo demonstrate that shortwave heating within the aerosol layer above Ascension Island can locally range between 2 and 8 K per day depending on the aerosol optical properties, though impacts of the aerosol can be felt elsewhere in the atmospheric column. When considered under clear conditions, the aerosol has a cooling effect at the TOA and based on the observed cloud properties at Ascension Island, the cloud albedo is not large enough to overcome this. Shortwave radiative heating due to biomass burning aerosol is not balanced by additional longwave cooling, and the net radiative impact results in a stabilization of the lower troposphere. However, these results are extremely sensitive to the single scattering albedo assumptions in models.

Allison B. Marquardt Collow↗
NASA NTRSDate not supplied

Wildfire-Induced CO Plume Observed during FIREX-AQ Experiment 1 and 2

The Fire Influence on Regional to Global Environments and Air Quality (FIREX AQ) field campaign was conducted during August 2019 to investigate the impact of wildfire and biomass smoke on air quality and weather in the continental United States. Ultra-spectral resolved infrared measurements contain information about tropospheric carbon monoxide (CO) and ozone (O3), as well as other trace species. A methodology of retrieving these tropospheric trace species from such remotely sensed spectral data has been developed and validated for the National Airborne Sounder Testbed-Interferometer (NAST I). NAST I CO and O3 measurements from the recent FIREX AQ field campaign are presented herein and used to estimate wildfire plume age. Results show enhanced CO plume evolution and transport away from fire ground site, and its plume age associated with the plume distance in both vertical and horizontal directions from the wildfire location, as enabled by the moderate-vertical and high-horizontal resolution obtained from the NAST I remotely sensed IR spectrometer onboard NASA ER 2 aircraft. This study advances our knowledge of fire-induced plume with its evolution and age in 3-dimensional space.

remote sensing↗
NASA NTRS2022

Estimation of Fire-induced CO Plume Age from NAST-I During the FIREX-AQ Field Campaign

Ultra-spectrally resolved infrared measurements from aircraft and space-based observations contain information about tropospheric carbon monoxide (CO) and ozone (O3), as well as other trace species. A methodology for retrieving these tropospheric trace species from such remotely sensed spectral data has been developed and validated for the National Airborne Sounder Testbed-Interferometer (NAST–I). The Fire Influence on Regional to Global Environments and Air Quality (FIREX-AQ) field campaign was conducted during August 2019 to investigate the impact of wildfire and biomass smoke on air quality and weather in the continental United States. NAST–I CO and O3 measurements from the recent FIREX-AQ field campaign are presented and used to estimate wildfire plume age. Results show enhanced levels of CO in the evolving plume as it is transported away from the fire ground site, and its plume age is associated with the plume distance in both the vertical and horizontal directions from the wildfire location. These results are enabled by the moderate-vertical and high-horizontal resolution obtained from the NAST–I IR spectrometer onboard the NASA ER-2 aircraft. This study advances our knowledge of fire-induced plumes with their evolution and age characterized in three-dimensional space using information from NAST–I retrieved CO and O3 and relative changes in their concentrations.

plume age↗
DOE OSTI2020

Radiative heating rate profiles over the southeast Atlantic Ocean during the 2016 and 2017 biomass burning seasons

Marine boundary layer clouds, including the transition from stratocumulus to cumulus, are poorly represented in numerical weather prediction and general circulation models. Further uncertainties in the cloud structure arise in the presence of biomass burning carbonaceous aerosol, as is the case over the southeast Atlantic Ocean, where biomass burning aerosol is transported from the African continent. As the aerosol plume progresses across the southeast Atlantic Ocean, radiative heating within the aerosol layer has the potential to alter the thermodynamic environment and therefore the cloud structure; however, limited work has been done to quantify this along the trajectory of the aerosol plume in the region. The deployment of the first Atmospheric Radiation Measurement (ARM) Mobile Facility (AMF1) in support of the Layered Atlantic Smoke Interactions with Clouds field campaign provided a unique opportunity to collect observations of cloud and aerosol properties during two consecutive biomass burning seasons during July through October of 2016 and 2017 over Ascension Island (7.96° S, 14.35° W). Using observed profiles of temperature, humidity, and clouds from the field campaign alongside aerosol optical properties from Modern-Era Retrospective analysis for Research and Applications, Version 2 (MERRA-2), as input for the Rapid Radiation Transfer Model (RRTM), profiles of the radiative heating rate due to aerosols and clouds were computed. Radiative heating is also assessed across the southeast Atlantic Ocean using an ensemble of back trajectories from the Hybrid Single Particle Lagrangian Integrated Trajectory (HYSPLIT) model. Idealized experiments using the RRTM with and without aerosols and a range of values for the single-scattering albedo (SSA) demonstrate that shortwave (SW) heating within the aerosol layer above Ascension Island can locally range between 2 and 8 K d -1 depending on the aerosol optical properties, though impacts of the aerosol can be felt elsewhere in the atmospheric column. When considered under clear conditions, the aerosol has a cooling effect at the TOA, and based on the observed cloud properties at Ascension Island, the cloud albedo is not large enough to overcome this. Shortwave radiative heating due to biomass burning aerosol is not balanced by additional longwave (LW) cooling, and the net radiative impact results in a stabilization of the lower troposphere. However, these results are extremely sensitive to the single-scattering albedo assumptions in models.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRSDate not supplied

Wildfire-Induced CO Plume Observation from NAST-I

Ultra-spectral resolved infrared measurements from aircraft and space-based observations contain information about tropospheric carbon monoxide (CO) and ozone (O3), as well as other trace species. A methodology of retrieving these tropospheric trace species from such remotely sensed spectral data has been developed and validated for the National Airborne Sounder Testbed-Interferometer (NAST-I). The Fire Influence on Regional to Global Environments and Air Quality (FIREX-AQ) field campaign was conducted during August 2019 to investigate the impact of wildfire and biomass smoke on air quality and weather in the continental United States. NAST-I CO and O3 measurements from the recent FIREX-AQ field campaign are presented herein and used to estimate wildfire plume age. Results show enhanced CO plume evolution and transport away from fire ground site, and its plume age associated with the plume distance in both vertical and horizontal directions from the wildfire location, as enabled by the moderate-vertical and high-horizontal resolution obtained from the NAST-I remotely sensed IR spectrometer onboard NASA ER-2 aircraft. This study advances our knowledge of fire-induced plume with its evolution and age in 3-dimensional space.

Wildfire↗
DOE OSTI2020

Open cells exhibit weaker entrainment of free-tropospheric biomass burning aerosol into the south-east Atlantic boundary layer

This work presents synergistic satellite, airborne and surface-based observations of a pocket of open cells (POC) in the remote south-east Atlantic. The observations were obtained over and upwind of Ascension Island during the CLouds and Aerosol Radiative Impacts and Forcing (CLARIFY) and the Layered Smoke Interacting with Clouds (LASIC) field experiments. A novel aspect of this case study is that an extensive free-tropospheric biomass burning aerosol plume that had been transported from the African continent was observed to be in contact with the boundary layer inversion over the POC and the surrounding closed cellular cloud regime. The in situ measurements show marked contrasts in the boundary layer thermodynamic structure, cloud properties, precipitation and aerosol conditions between the open cells and surrounding overcast cloud field. The data demonstrate that the overlying biomass burning aerosol was mixing down into the boundary layer in the stratocumulus cloud downwind of the POC, with elevated carbon monoxide, black carbon mass loadings and accumulation-mode aerosol concentrations measured beneath the trade-wind inversion. The stratocumulus cloud in this region was moderately polluted and exhibited very little precipitation falling below cloud base. A rapid transition to actively precipitating cumulus clouds and detrained stratiform remnants in the form of thin quiescent veil clouds was observed across the boundary into and deep within the POC. The subcloud layer in the POC was much cleaner than that in the stratocumulus region. The clouds in the POC formed within an ultra-clean layer (accumulation-mode aerosol concentrations of approximately a few cm -3 ) in the upper region of the boundary layer, which was likely to have been formed via efficient collision–coalescence and sedimentation processes. Enhanced Aitken-mode aerosol concentrations were also observed intermittently in this ultra-clean layer, suggesting that new particle formation was taking place. Across the boundary layer inversion and immediately above the ultra-clean layer, accumulation-mode aerosol concentrations were ~1000 cm -3 . Importantly, the air mass in the POC showed no evidence of elevated carbon monoxide over and above typical background conditions at this location and time of year. As carbon monoxide is a good tracer for biomass burning aerosol that is not readily removed by cloud processing and precipitation, it demonstrates that the open cellular convection in the POC is not able to entrain large quantities of the free-tropospheric aerosol that was sitting directly on top of the boundary layer inversion. This suggests that the structure of the mesoscale cellular convection may play an important role in regulating the transport of aerosol from the free troposphere down into the marine boundary layer. We then develop a climatology of open cellular cloud conditions in the south-east Atlantic from 19 years of September Moderate Resolution Imaging Spectroradiometer (MODIS) Terra imagery. This shows that the maxima in open cell frequency (> 0.25) occurs far offshore and in a region where subsiding biomass burning aerosol plumes may often come into contact with the underlying boundary layer cloud. If the results from the observational case study applied more broadly, then the apparent low susceptibility of open cells to free-tropospheric intrusions of additional cloud condensation nuclei could have some important consequences for aerosol–cloud interactions in the region.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1992

Hover performance validation of an ejector configured STOVL fighter aircraft

The hover thrust performance of a full-scale model of an ejector-lift/vectored thrust Short Take-Off and Vertical Landing (STOVL) fighter configuration was measured at the Outdoor Aerodynamic Research Facility of the National Full-Scale Aerodynamics Complex located at NASA Ames Research Center. The static thrust of the lifting ejector and ventral nozzle was calibrated at an out-of-ground-effect height. The test permitted comparison with static thrust calibrations obtained in the 80- by 120-Foot Wind Tunnel. The average static thrust augmentation ratio of the ejector system was 1.55 compared with the design goal of 1.63. The outdoor test showed that the addition of short extensions to the diffuser on the fuselage sidewall decreased suckdown and increased ejector performance. As expected, an increase in the ventral nozzle thrust deflection angle from nearly horizontal to the vertical-lift hover position caused a significant decrease in thrust. Flow visualization using smoke revealed greater secondary airflow into the left ejector and the penetration of hot ventral gases along the ground beneath and between the cool plumes from the ejector system.

Naumowicz, Tim↗
NASA NTRS1998

Algorithm for Estimating the Plume Centerline Temperature and Ceiling Jet Temperature in the Presence of a Hot Upper Layer

The experiments were designed to provide insight into the behavior of jet fuel fires in aircraft hangars and to study the impact of these fires on the design and operation of a variety of fire protection systems. As a result, the test series included small fires designed to investigate the operation of UV/IR detectors and smoke detectors as well as large fires which were used to investigate the operation of ceiling mounted heat detectors and sprinklers. The impact of the presence or absence of draft curtains was also studied in the 15 m hangar. It is shown that in order to predict the plume centerline temperature within experimental uncertainty, the entrainment of the upper layer gas must be modeled. For large fires, the impact of a changing radiation fraction must also be included in the calculation. The dependence of the radial temperature profile of the ceiling jet as a function of layer development is demonstrated and a ceiling jet temperature algorithm which includes the impact of a growing layer is developed.

ALGORITHMS↗
NASA NTRS2022

The 2019 Raikoke volcanic eruption -Part 2: Particle-phase dispersion and concurrent wildfire smoke emissions

Between 27 June and 14 July 2019 aerosol layers were observed by the United Kingdom (UK) Raman lidar network in the upper troposphere and lower stratosphere. The arrival of these aerosol layers in late June caused some concern within the London Volcanic Ash Advisory Centre (VAAC) as according to dispersion simulations the volcanic plume from the 21 June 2019 eruption of Raikoke was not expected over the UK until early July. Using dispersion simulations from the Met Office Numerical Atmospheric-dispersion Modelling Environment (NAME), and supporting evidence from satellite and in situ aircraft observations, we show that the early arrival of the stratospheric layers was not due to aerosols from the explosive eruption of the Raikoke volcano but due to biomass burning smoke aerosols associated with intense forest fires in Alberta, Canada, that occurred 4 d prior to the Raikoke eruption. We use the observations and model simulations to describe the dispersion of both the volcanic and forest fire aerosol clouds and estimate that the initial Raikoke ash aerosol cloud contained around 15 Tg of volcanic ash and that the forest fires produced around 0.2 Tg of biomass burning aerosol. The operational monitoring of volcanic aerosol clouds is a vital capability in terms of aviation safety and the synergy of NAME dispersion simulations, and lidar data with depolarising capabilities allowed scientists at the Met Office to interpret the various aerosol layers over the UK and attribute the material to their sources. The use of NAME allowed the identification of the observed stratospheric layers that reached the UK on 27 June as biomass burning aerosol, characterised by a particle linear depolarisation ratio of 9 %, whereas with the lidar alone the latter could have been identified as the early arrival of a volcanic ash–sulfate mixed aerosol cloud. In the case under study, given the low concentration estimates, the exact identification of the aerosol layers would have made little substantive difference to the decision-making process within the London VAAC. However, our work shows how the use of dispersion modelling together with multiple observation sources enabled us to create a more complete description of atmospheric aerosol loading.

Martin J Osborne↗
DOE OSTI2026

Hourly PM 2.5 Estimates across California from 2018 to 2023

This study presents a new data set of hourly PM 2.5 concentrations across California from 2018 to 2023 at a three-kilometer resolution. This data set was developed by assimilating observations from PurpleAir and the U.S. EPA Air Quality System monitors into wildfire smoke forecasts from the High-Resolution Rapid Refresh Smoke (HRRR-Smoke) model using the Gridpoint Statistical Interpolation (GSI) three-dimensional variational data assimilation framework. Archived forecasts of modeled wildfire smoke PM 2.5 from HRRR-Smoke create the background field for assimilation, which is then corrected using surface observations of total PM 2.5 . The resulting reanalysis from GSI provides an estimate of total PM 2.5 that minimizes error from both the observational and the model data. Validation results indicate strong performance, with monthly R 2 values ranging from 0.73 to 0.91 across the six-year data set, comparable to other PM 2.5 data sets. Case studies are presented for three major fire events, the 2018 Camp Fire, 2019 Kincade Fire, and 2020 Lightning Complex Fires to demonstrate the data set’s fidelity in resolving plume dynamics and local exposure patterns. Root-mean-squared error averaged over each month scales with average PM 2.5 concentrations, resulting in a low error under typical conditions but higher absolute errors during extreme smoke events. This is the first long-term, hourly PM 2.5 data set of its kind for California and enables the generation of subdaily exposure metrics, such as peak hourly concentrations, exceedance durations, and time-of-day exposure peaks. The novelty and strong validation of this data set make it a compelling resource for future studies on the impact and significance of subdaily PM 2.5 exposure.

PM2.5↗
NASA NTRS2004

Rapid Measurements of Aerosol Ionic Composition and 3-10 nm Particle Size Distributions On The NASA P3 To Better Quantify Processes Affecting Aerosols Advected From East Asia

The Particle Into Liquid Sample (PILS) was deployed on the NASA P3 for airborne measurements of fine particle ionic chemical composition. The data have been quality assured and reside in the NASA data archive. We have analyzed our data to characterize the sources and atmospheric processing of fine aerosol particles advected from the region during the experiments. Fine particle water-soluble potassium was found to serve as a useful aerosol tracer for biomass smoke. Ratios of PILS potassium to sulfate are used as a means of estimating the percent contribution of biomass burning to fine particle mass in mixed plumes advecting from Asia. The high correlations between K+ and NO3(sup -) and NH4(sup +)' indicated that biomass burning was a significant source of these aerosol compounds in the region. It is noteworthy that the air mass containing the highest concentrations of fine particles recorded in all of ACE-Asia and TRACE-P appeared to be advecting from the Bejing/Tientsin urban region and also had the highest K(+), NO3(sup -) and NH4(sup +) concentrations of both studies. Based on K+/SO4(sup 2-) ratio's, we estimated that the plume was composed of approx. 60% biomass burning emissions, possibly from the use of bio-fuels in the urban regions.

Weber, Rodney J.↗
DOE OSTI2021

Upper Troposphere Smoke Injection From Large Areal Fires

Abstract Large areal fires, such as those ignited following a nuclear detonation, can inject smoke into the upper troposphere and lower stratosphere. Detailed fire simulations allow for assessment of how local weather interacts with these fires and affects smoke lofting. In this study, we employ the fire simulation package in the Weather Research and Forecasting (WRF‐Fire) model, Version 4.0.1, to explore how smoke lofting from a fire burning a homogeneous fuel bed changes with varying local winds, relative humidity, and atmospheric boundary‐layer stability for two different‐sized areal fires. The presence of moisture has the greatest influence on the results by raising the altitude of lofting, while faster wind speeds dampen lofting and lower the injection height. Stably stratified conditions inhibit plume propagation compared with neutrally stratified conditions, although the impact of stability is not as strong as that of moisture and winds. These findings highlight the importance of using an appropriate atmospheric profile when simulating large fires, as the local weather can have a meaningful influence on smoke lofting.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Intensive aerosol properties of boreal and regional biomass burning aerosol at Mt. Bachelor Observatory: larger and black carbon (BC)-dominant particles transported from Siberian wildfires

We characterize the aerosol physical and optical properties of 13 transported biomass burning (BB) events. BB events included long-range influence from fires in Alaskan and Siberian boreal forests transported to Mt. Bachelor Observatory (MBO) in the free troposphere (FT) over 8–14+ d and regional wildfires in northern California and southwestern Oregon transported to MBO in the boundary layer (BL) over 10 h to 3 d. Intensive aerosol optical properties and normalized enhancement ratios for BB events were derived from measured aerosol light scattering coefficients (σ scat ), aerosol light-absorbing coefficients (σ abs ), fine particulate matter (PM 1 ), and carbon monoxide (CO) measurements made from July to September 2019, with particle size distribution collected from August to September. The observations showed that the Siberian BB events had a lower scattering Ångström exponent (SAE), a higher mass scattering efficiency (MSE; Δσ scat /ΔPM 1 ), and a bimodal aerosol size distribution with a higher geometric mean diameter (D g ). We hypothesize that the larger particles and associated scattering properties were due to the transport of fine dust alongside smoke in addition to contributions from condensation of secondary aerosol, coagulation of smaller particles, and aqueous-phase processing during transport. Alaskan and Siberian boreal forest BB plumes were transported long distances in the FT and characterized by lower absorption Ångström exponent (AAE) values indicative of black carbon (BC) dominance in the radiative budget. Significantly elevated AAE values were only observed for BB events with <1 d transport, which suggests strong production of brown carbon (BrC) in these plumes but limited radiative forcing impacts outside of the immediate region.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2020

Evaluation of Stratospheric Intrusions and Biomass Burning Plumes on the Vertical Distribution of Tropospheric Ozone Over the Midwestern U.S.

Naturally occurring ozone rich Stratosphere-to-Troposphere Transport (STT) intrusions and biomass burning plumes reaching the surface can contribute to exceedances of the U.S. National Ambient Air Quality Standards (NAAQS) for ground-level ozone (70 ppbv implemented in 2015). In addition, fires can inject significant pollution into the free troposphere where it can be transported long distances. The combined air quality impacts from these sources on ozone has only been analyzed in a few case studies for the Midwest U.S. Here we study ozone impacts in a major Midwestern city, for the first time in St. Louis, Missouri, using a series of ozonesonde profiles taken during the SEAC4RS (Studies of Emissions and Atmospheric Composition, Clouds and Climate Coupling by Regional Surveys) field campaign in August-September 2013. All ozonesondes showed some enhancements above the background profile levels (~55 ppbv) throughout each tropospheric column. Two models were used to estimate and quantify ozone origins within the columns. A chemical transport model identified enhancements from STT equivalent to 10to15 ppbv over the background with a 10 to15% contribution overall to the column. Two FLEXPART-WRF simulations, one with smoke in the boundary layer and the other with smoke above, identified enhancements from biomass burning equivalent to 10to 80 ppbv. Overall, the total biomass burning contribution is 15to 30% of the total column. Five ozonesondes showed signatures of mixed biomass burning plumes and STT intrusions. During this study period, biomass burning in the western U.S. contributed 70% to ozone enhancements in the total column compared to 3% from the central U.S and 27% from other areas.

National Ambient Air Quality Standards for ground‐↗
NASA NTRS1993

Vapor-Generator Wand Helps To Reveal Airflow Patterns

In vapor-generator wand, liquid propylene glycol flows into electrically heated stainless-steel tube. Liquid boils in heated tube, and emerging vapor forms dense, smoke-like fog used to make airflow patterns visible. Built in variety of sizes, suitable for uses ranging from tabletop demonstrations to research in wind tunnels. For best viewing, plume illuminated by bright, focused incandescent spotlight at right angle to viewing direction. Viewing further enhanced by coating walls of test chamber with flat, dark color to minimize reflections and increase contrast.

Robelen, David B.↗