Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “slots”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

AMELIA CESTOL Test: Acoustic Characteristics of Circulation Control Wing with Leading-and Trailing-Edge Slot Blowing

Aeroacoustic measurements of the 11 % scale full-span AMELIA CESTOL model with leading- and trailing-edge slot blowing circulation control (CCW) wing were obtained during a recent test in the Arnold Engineering Development Center 40- by 80-Ft. Wind Tunnel at NASA Ames Research Center, Sound levels and spectra were acquired with seven in-flow microphones and a 48-element phased microphone array for a variety of vehicle configurations, CCW slot flow rates, and forward speeds, Corrections to the measurements and processing are in progress, however the data from selected configurations presented in this report confirm good measurement quality and dynamic range over the test conditions, Array beamform maps at 40 kts tunnel speed show that the trailing edge flap source is dominant for most frequencies at flap angles of 0deg and 60deg, The overall sound level for the 60deg flap was similar to the 0deg flap for most slot blowing rates forward of 90deg incidence, but was louder by up to 6 dB for downstream angles, At 100 kts, the in-flow microphone levels were louder than the sensor self-noise for the higher blowing rates, while passive and active background noise suppression methods for the microphone array revealed source levels as much as 20 dB lower than observed with the in-flow microphones,

Horne, Clifton↗
NASA NTRS2012

Low Average Sidelobe Slot Array Antennas for Radiometer Applications

In radiometer applications, it is required to design antennas that meet low average sidelobe levels and low average return loss over a specified frequency bandwidth. It is a challenge to meet such specifications over a frequency range when one uses resonant elements such as waveguide feed slots. In addition to their inherent narrow frequency band performance, the problem is exacerbated due to modeling errors and manufacturing tolerances. There was a need to develop a design methodology to solve the problem. An iterative design procedure was developed by starting with an array architecture, lattice spacing, aperture distribution, waveguide dimensions, etc. The array was designed using Elliott s technique with appropriate values of the total slot conductance in each radiating waveguide, and the total resistance in each feed waveguide. Subsequently, the array performance was analyzed by the full wave method of moments solution to the pertinent integral equations. Monte Carlo simulations were also carried out to account for amplitude and phase errors introduced for the aperture distribution due to modeling errors as well as manufacturing tolerances. If the design margins for the average sidelobe level and the average return loss were not adequate, array architecture, lattice spacing, aperture distribution, and waveguide dimensions were varied in subsequent iterations. Once the design margins were found to be adequate, the iteration was stopped and a good design was achieved. A symmetric array architecture was found to meet the design specification with adequate margin. The specifications were near 40 dB for angular regions beyond 30 degrees from broadside. Separable Taylor distribution with nbar=4 and 35 dB sidelobe specification was chosen for each principal plane. A non-separable distribution obtained by the genetic algorithm was found to have similar characteristics. The element spacing was obtained to provide the required beamwidth and close to a null in the E-plane end-fire direction. Because of the alternating slot offsets, grating lobes called butterfly lobes are produced in non-principal planes close to the H-plane. An attempt to reduce the influence of such grating lobes resulted in a symmetric design.

Rengarajan, Sembiam↗
NASA NTRS2013

AMELIA CESTOL Test: Acoustic Characteristics of Circulation Control Wing with Leading- and Trailing-Edge Slot Blowing

The AMELIA Cruise-Efficient Short Take-off and Landing (CESTOL) configuration concept was developed to meet future requirements of reduced field length, noise, and fuel burn by researchers at Cal Poly, San Luis Obispo and Georgia Tech Research Institute under sponsorship by the NASA Fundamental Aeronautics Program (FAP), Subsonic Fixed Wing Project. The novel configuration includes leading- and trailing-edge circulation control wing (CCW), over-wing podded turbine propulsion simulation (TPS). Extensive aerodynamic measurements of forces, surfaces pressures, and wing surface skin friction measurements were recently measured over a wide range of test conditions in the Arnold Engineering Development Center(AEDC) National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Ft Wind Tunnel. Acoustic measurements of the model were also acquired for each configuration with 7 fixed microphones on a line under the left wing, and with a 48-element, 40-inch diameter phased microphone array under the right wing. This presentation will discuss acoustic characteristics of the CCW system for a variety of tunnel speeds (0 to 120 kts), model configurations (leading edge(LE) and/or trailing-edge(TE) slot blowing, and orientations (incidence and yaw) based on acoustic measurements acquired concurrently with the aerodynamic measurements. The flow coefficient, Cmu= mVSLOT/qSW varied from 0 to 0.88 at 40 kts, and from 0 to 0.15 at 120 kts. Here m is the slot mass flow rate, VSLOT is the slot exit velocity, q is dynamic pressure, and SW is wing surface area. Directivities at selected 1/3 octave bands will be compared with comparable measurements of a 2-D wing at GTRI, as will as microphone array near-field measurements of the right wing at maximum flow rate. The presentation will include discussion of acoustic sensor calibrations as well as characterization of the wind tunnel background noise environment.

Horne, William C.↗
NASA NTRS2013

Slotted Polyimide-Aerogel-Filled-Waveguide Arrays

Polyimide aerogels were considered to serve as a filling for millimeter-wave waveguides. While these waveguides present a slightly higher loss than hollow waveguides, they have less losses than Duroid substrate integrated waveguides (less than 0.15 dB at Ka-band, in a 20 mm section), and exhibit an order of magnitude of mass reduction when compared to commercial waveguides. A Ka-band slotted aerogel-filled-waveguide array was designed, which provided the same gain (9 dBi) as its standard waveguide counterpart, and a slotted aerogel-filled-waveguide array using folded-slots was designed for comparison, obtaining a gain of 9 dB and a bandwidth of 590 MHz.

surface integrated waveguides↗
NASA NTRSDate not supplied

Variable Mixing Nozzle Design with Slotted Vortex Generators for Jet Noise Reduction

A new variable geometry turbofan nozzle concept is presented with the dual goals of airport noise reduction and high propulsive efficiency at cruise, while employing only a single moving part. The nozzle utilizes a number of curved vanes to function as vortex generators (VGs) during takeoff and initial climb. Streamwise vortices provide an increase in mixing between the jet and external stream, with a resulting decrease in high frequency noise generation and a noise source distribution which is more amenable to airframe-based shielding. Unlike conventional VGs, the vanes are positioned without transverse incidence, and a pressure difference across the surface of each vane is created via an adjacent slot. During high altitude flight, when nozzle efficiency concerns outweigh any preference for jet noise reduction, all slots may be closed through rotation of a slotted ring inside the nozzle. RANS-based numerical analysis is performed to calculate propulsive metrics, determine noise source characteristics and understand various design parameter sensitivities. A new formulation is developed to approximately correct computed noise intensities for any throttle adjustments required to maintain takeoff thrust, and a rough estimate of shielding effectiveness is proposed by means of integration over a spatially distributed noise source. A total of 19 different nozzle geometries are considered in the present study. Results indicate significant noise benefits at takeoff, including a 2 kHz fly-over noise reduction of roughly 2-3 dB, while allowing for less than 15% of the net thrust reduction at supersonic cruise calculated for a fixed-penetration chevron nozzle.

Jet Noise↗
NASA NTRS1922

Problem of the slotted wing : a communication from the Aerodynamic Institute of the Aachen Technical High School

It is to be expected that the advantageous properties, hitherto discovered in many slotted wing sections, depend very largely on the contour of the slot and the structural details of the wing. It is therefore of interest, aside from measurements on wings of constant cross-section along the span, to measure also wing models in which the structural details have already been given practical consideration.

WINGS - EXPERIMENTS↗
NASA NTRS2013

Slotted Polyimide-Aerogel-Filled-Waveguide Arrays

This presentation discussed the potential advantages of developing Slotted Waveguide Arrays using polyimide aerogels. Polyimide (PI) aerogels offer great promise as an enabling technology for lightweight aerospace antenna systems. PI aerogels are highly porous solids possessing low density and low dielectric permittivity combined with good mechanical properties. For slotted waveguide array applications, there are significant advantages in mass that more than compensate for the slightly higher loss of the aerogel filled waveguide when compared to state of practice commercial waveguide.

Slotted Waveguide Arrays↗
NASA NTRSDate not supplied

Evaluation of Variable-Depth Liners with Slotted Cores

An initial evaluation of variable-depth, slotted-core liners fabricated with conventional, flightworthy com-ponents is presented. Liners with two distinct chamber lengths provide significant broadband absorption and their impedances are, to first order, predictable with the NASA impedance prediction code. These liners employ film caps embedded in alternating chambers to provide a near-rigid boundary condition. This enables improved control of the liner design process. A number of additively-manufactured, bent-chamber liners are also investigated to explore the e˙ects of the bend on the liner impedance. The liner impedance is negligibly a˙ected by changes to the partition width, but is significantly a˙ected by changes to the slot height. This o˙ers an option for achieving low-frequency sound absorption with relatively thin liners.

acoustic↗
NASA NTRSDate not supplied

Evaluation of Variable-Depth Liners with Slotted Cores

An initial evaluation of variable-depth, slotted-core liners fabricated with conventional, flightworthy components is presented. Liners with two distinct chamber lengths provide significant broadband absorption and their impedances are, to first order, predictable with the NASA impedance prediction code. These liners employ film caps embedded in alternating chambers to provide a near-rigid boundary condition. This enables improved control of the liner design process. A number of additively-manufactured, bent-chamber liners are also investigated to explore the effects of the bend on the liner impedance. The liner impedance is negligibly affected by changes to the partition width, but is significantly affected by changes to the slot height. This offers an option for achieving low-frequency sound absorption with relatively thin liners.

acoustic↗
NASA NTRS1972

Wind tunnel investigation of a large scale 35 deg swept wing jet transport model with an external blowing triple slotted flap

An investigation was conducted to determine the aerodynamic characteristics of a large-scale subsonic jet transport model with an externally jet-augmented flap system that would augment lift and provide direct-lift control. The model had a 35 deg swept wing of aspect ratio 7.82 and two side-by-side engines mounted on a single pylon under each wing close to the fuselage. The lift of the flap system was augmented by jet engine exhaust impingement on the triple-slotted flap surfaces. The rearmost flap provided direct lift control. Results were obtained for several combinations of flap deflections at gross thrust coefficients from 0 to 2.0. Three-component longitudinal data are presented with four engines operating. Limited longitudinal and lateral data are presented for asymmetric and symmetric thrust conditions with three engines operating. For the same overall flap deflection, lift coefficient and maximum lift coefficient were improved 13 and 7 percent compared to coefficients obtained with a double-slotted flap configuration. A maximum lift coefficient of 6.3 was obtained at a gross thrust coefficient of 2.0. At the same flap deflection lateral and directional trim moment requirements with an engine inoperative were reduced 55 and 33 percent, respectively, compared to those with the engines located farther outboard on the wing. Trim moment requirements in pitch were also reduced significantly. However, pitching-moment instability occurred and increased with gross thrust coefficient.

Aoyagi, K.↗
NASA NTRS1972

A finite difference method for predicting supersonic turbulent boundary layer flows with tangential slot injection

An implicit finite difference method has been applied to tangential slot injection into supersonic turbulent boundary layer flows. In addition, the effects induced by the interaction between the boundary layer displacement thickness and the external pressure field are considered. In the present method, three different eddy viscosity models have been used to specify the turbulent momentum exchange. One model depends on the species concentration profile and the species conservation equation has been included in the system of governing partial differential equations. Results are compared with experimental data at stream Mach numbers of 2.4 and 6.0 and with results of another finite difference method. Good agreement was generally obtained for the reduction of wall skin friction with slot injection and with experimental Mach number and pitot pressure profiles. Calculations with the effects of pressure interaction included showed these effects to be smaller than effects of changing eddy viscosity models.

Miner, E. W.↗
NASA NTRS1972

Effect of a slot on the buckling load of a cylindrical shell with a circular cutout.

The results are discussed of a study of the effect of slots on the buckling of cylinders with circular holes of systematically varied circularity. The results obtained suggest that the substantial increase in the buckling loads of cylindrical shells resulting from increases in slot length is due to a relief of the bending stress field.

Starnes, J. H., Jr.↗
NASA NTRS1973

Design and experimental performance of short curved wall diffusers with axial symmetry utilizing slot suction

The feasibility of designing short curved wall axially symmetrical subsonic diffusers utilizing suction through slots in the diffuser walls to prevent flow separation was investigated. A potential flow analysis was made, and a digital computer program was written for determining the diffuser wall contour for prescribed boundary conditions. The flow field included branch flow so that the suction slot geometry could be a part of the diffuser design. One bell shaped diffuser and three annular diffusers with area ratios of either 2.5:1 or 3:1 were designed, fabricated, and tested. Minimum suction requirements of metastable operation ranged from 6.3 percent to 12 percent when operating with inlet air velocities in the 1000 to 250 ft/sec (30 to 76 m/sec) range. For stable operation suction rates from 10 percent to 22 percent were required. In all cases the diffuser effectiveness was above 95 percent based on the conventional definition, and from 81 percent to 94 percent when the suction loss was accounted for. The exit velocity profiles were virtually flat with no more than + or - 9% variation over 95 percent of the exit area when operated with sufficient suction to prevent flow separation.

Yang, T.↗
NASA NTRS1973

Supersonic turbulent boundary-layer flows with tangential slot injection.

An implicit finite-difference method has been developed for the solution of the compressible boundary-layer equations. This method is applied to tangential slot injection into supersonic turbulent boundary-layer flows. In addition, the effects induced by the interaction between the boundary-layer displacement thickness and the external pressure field are considered. Three different eddy viscosity models have been used to specify the turbulent momentum exchange. One model depends on the species concentration profile, and the species conservation equation has been included in the system of governing partial differential equations. For air injected into air, the freestream and injected gases are treated as separate species which have common fluid properties. Calculations were made and results were compared with experimental data at freestream Mach numbers of 2.4 and 6.0 and with results of another finite-difference method. Good agreement was obtained for the reduction of wall skin friction with slot injection.

Miner, E. W.↗