Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “refinement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Grain Refinement by Authigenic Inoculation Inherited from the Medium-Range Order Structure of Ni-Cr-W Superalloy

The combination of liquidus casting and thermal control solidification furnace was applied to obtain a fine-grained ingot. A rapid quenching method and x-ray diffraction measurement were used to investigate the effect of authigenic inoculation on grain refinement. The structure factor S(Q) of liquid Ni-Cr-W superalloy at 1400 °C (Liquidus temperature) and bright-field image of the microstructures quenched from 1400 °C have been measured by the high-temperature x-ray diffractometer and the transmission electron microscopy (TEM), respectively. The results show that a pre-peak exists on a S(Q) curve at the liquidus temperature. The clusters of atom in rapidly quenched microstructures obtained by isothermal heat treatment at 1400 °C were studied using TEM. Meanwhile, the effect of isothermal different temperatures on rapidly quenched microstructures was studied. The results also show that there are only the globular, equiaxed grains distributed in the solidification structure. These particles are inherited from the medium-range order structure, which is beneficial for grain refinement. The normalized work-hardening rate-strain curve indicates the work-hardening rate of fine grain is higher than that of conventional grain at the same temperature and the same deformation.

36 MATERIALS SCIENCE↗

Corrosion Behavior of B and Ti Grain-Refined Sr-Modified A356

Corrosion behavior of A356 aluminum alloy with different grain refiners was evaluated. For this purpose, the Sr-modified A356 alloy was grain refined with Al5Ti1B and Al3B, and then, the corrosion characteristics were determined. For the mechanical properties, impact and Vickers hardness tests were carried out. To determine the corrosion behavior, both the electrochemical impedance spectroscopy technique and by potentiodynamic polarization plots were carried out in a 3.5 wt.% NaCl solution at 25 °C. The corrosion resistance of A356 alloy was dramatically improved in sequence with the following modifications compared to the unmodified castings: Sr, Ti and B additions. This situation applies to both different cooling rates, namely die and sand casting. The increase in corrosion rate was more than 80% for all alterations of the microstructure. Additionally, charge transfer resistance was increased ten times in die cast samples, while this value was 2.5 for sand cast samples compared to the unmodified alloy. It is important to note that sand casting of the unmodified alloy was improved four times with regard to the die cast unmodified A356.

36 MATERIALS SCIENCE↗

Achieving Grain Refinement and Related Mechanical Property Improvement of an Al-Zn-Mg-Cu Alloy Through Severe Plastic Deformation

Microstructural features and mechanical properties of an Al-Zn-Mg-Cu alloy processed by equal-channel angular pressing (ECAP) have been investigated. The equivalent plastic strain obtained from the simulation agrees well with that from the analytical calculation in a way that both increase with an increase in deformation, but the strain distribution is non-uniform, appearing as a strain gradient along the norm direction. Microstructure investigation shows that grain refinement is achieved in frequency of low-angle grain boundaries fabricated by ECAP. The pole density is reduced by ECAP, during which the Brass and Goss type textures are introduced. TEM results show chain-like recrystallized grains formed at the grain boundaries and broken second-phase particles come into being due to the heavy shear force. After ECAP, the hardness and strength increase significantly while the elongation is reduced. Besides, an extreme strengthening is confirmed because of the balance between dynamic hardening and softening. The microstructure evolution mechanism is revealed in terms of grain refinement, precipitate phase breakage and texture evolution.

36 MATERIALS SCIENCE↗

Grain Refinement Mechanism and Microstructural Evolution of M50NiL Steel during Multi-directional Impact Forging

This study investigated the effect of varying temperatures and cumulative strains on M50NiL steel during multi-directional impact forging (MDIF). The grain size was found to increase gradually with increasing temperature, after being held at 1050, 1100, 1150 and 1180 °C for 30 min, with the minimum grain size observed at 1100 °C during the MDIF process. The M50NiL steel subjected to MDIF at 1100 °C and at varying cumulative strains of 0.6, 1.8, 3.6 and 7.2 exhibited grain sizes that decreased with increasing cumulative strain. The mean grain size gradually decreased to ~ 1 μm at a cumulative strain of 7.2. New small grains were nucleated at grain boundaries via dynamic recrystallization, and microbands were formed via the temperature drop during the continuous forging process. The grains were subdivided into subgrains by the microbands, and these subgrains were converted to new refined grains via transformation of their boundaries into high-angle boundaries. Further, martensite transformation was restrained owing to the grain refinement. Improved tensile strengths values are obtained after MDIF process.

36 MATERIALS SCIENCE↗

Synergetic Strengthening of Grain Refinement and Texture in Gradient Zircaloy-4 by Surface Mechanical Rolling Treatment

A Zircaloy-4 rod was subjected to surface mechanical rolling treatment (SMRT) to form a gradient structure, and the evolution of the resulting sub-grain-boundary property and texture across the gradient structure was characterized using electron backscattered diffraction. Dual-gradient structures in grain size and orientation were formed; the grain size was refined from several microns at the center to approximately 400 nm at the topmost surface. Texture analysis revealed that the c-axis gradually tilted from a random orientation toward the parallel-to-radial direction on the radial–tangential plane. The SMRT-induced formation of the dual-gradient microstructure is attributed to the formation of gradient distributions of stress and strain, which resulted in various deformation mechanisms (twinning and dislocation) being active at different depths. During the SMRT process, twinning and dislocations were activated to refine the grains. When the dual-gradient microstructure formed, twinning was mainly activated at the subsurface near the matrix, whereas dislocations were activated across the entire gradient. The geometrically necessary dislocation density increased with decreasing depth and then slightly decreased near the surface. The synergetic strengthening of the dual-gradient microstructure resulted in a gradient distribution of the microhardness near the surface. Thus, the Zircaloy-4 rod exhibited a good combination of strength and ductility.

36 MATERIALS SCIENCE↗

eBits: Compact stream of mesh refinements for remote visualization

Here, we focus on applications where a remote client needs to visualize or process a complex, manifold triangle mesh, M , but only in a relatively small, user controlled, Region of Interest (RoI) at a time. The client first downloads a coarse base mesh , pre-computed on the server via a series of simplification passes on M , one per Level of Detail (LoD), each pass identifying an independent set of triangles, collapsing them, and, for each collapse, storing, in a Vertex Expansion Record (VER), the information needed to reverse the collapse. On each client initiated RoI modification request, the server pushes to the client a selected subset of these VERs, which, when decoded and applied to refine the mesh locally, ensure that the portion in the RoI is always at full resolution. The eBits approach proposed here offers state of the art compression ratios (using less than 2.5 bits per new full resolution RoI triangle when the RoI has more than 2000 vertices to transmit the connectivity for the selective refinements) and fine-grain control (allowing the user to adjust the RoI by small increments). The effectiveness of eBits results from several novel ideas and novel variations of previous solutions. We represent the VERs using persistent labels so that they can be applied in different orders within a given LoD. The server maintains a shadow copy of the client’s mesh. To avoid sending IDs identifying which vertices should be expanded, we either transmit, for each new vertex, a compact encoding of its death tag –the LoD at which it will be expanded if it lies in the Rol–or transmit vertex masks for the RoI and its neighboring vertices. We also propose a three-step simplification that reduces the overall transmission cost by increasing both the simplification effectiveness and the regularity of the valences in the resulting meshes.

97 MATHEMATICS AND COMPUTING↗

Effect of grain refinement on high temperature steam oxidation of an FeCrAl alloy

FeCrAl alloys are promising candidates to replace Zr alloys as fuel cladding materials in nuclear light-water reactors. Grain refinement has been indicated to improve irradiation resistance. To enhance corrosion resistance as well, the effects of grain refinement on steam corrosion behavior were investigated in this work. Samples of Kanthal D alloy (Fe-21Cr-5Al) with two different grain sizes (coarse-grained and ultrafine-grained) were exposed to steam at 1200 °C for 2 hrs. In conclusion, results indicate improved steam corrosion resistance in ultrafine-grained Kanthal D with formation of a thinner protective Al oxide layer and the presence of a thin underlying Cr oxide layer.

36 MATERIALS SCIENCE↗

Composite matrix construction for structured grid adaptive mesh refinement

Structured-grid adaptive mesh refinement (SAMR) is an approach to mesh generation that supports structured access to data and adaptive mesh refinement for discretized partial differential equations (PDEs). Solution algorithms often require that an inverse of an operator be applied, a system of algebraic equations must be solved, and this process is often the primary computational cost in an application. SAMR is well suited to geometric multigrid solvers, which can be effective, but often do not adapt well to complex geometry including material coefficients. Algebraic multigrid (AMG) is more robust in the face of complex geometry, in both boundary conditions and internal material interfaces. AMG requires a stored matrix linearization of the operator. We discuss an approach, and an implementation in the Chombo block-structured AMR framework, for constructing composite grid matrices from a SAMR hierarchy of grids for use in linear solvers in the PETSc numerical library. We consider a case study with the Chombo-based BISICLES ice sheet modeling application.

97 MATHEMATICS AND COMPUTING↗

Interpolation methods and the accuracy of lattice-Boltzmann mesh refinement

A lattice-Boltzmann model to solve the equivalent of the Navier-Stokes equations on adap- tively refined grids is presented. A method for transferring information across interfaces between different grid resolutions was developed following established techniques for finite- volume representations. This new approach relies on a space-time interpolation and solving constrained least-squares problems to ensure conservation. The effectiveness of this method at maintaining the second order accuracy of lattice-Boltzmann is demonstrated through a series of benchmark simulations and detailed mesh refinement studies. These results exhibit smaller solution errors and improved convergence when compared with similar approaches relying only on spatial interpolation. Examples highlighting the mesh adaptivity of this method are also provided.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of acicular ferrite formation on grain refinement in the coarse-grained region of heat-affected zone

The microstructure of acicular ferrite and its formation for the grain refinement of coarse-grained region of heat-affected zone of high strength low-alloy bainite steels were studied using three-dimensional reconstruction technique. Crystallographic grain size was analyzed by means of electron backscatter diffraction. It was revealed that the microstructure in the coarse-grained region of the heat-affected zone consisted of predominantly bainite packets and a small proportion of acicular ferrite. Acicular ferrite was of lath or plate-like rather than needle or rod-like morphology. Tempering of the coarse-grained region of heat-affected zone showed that the acicular ferrite was more stable than the bainite, indicating that the acicular ferrite was formed prior to bainite. The acicular ferrite laths or plates divided the prior austenite grains into smaller and separate regions, and confining the bainite transformed at lower temperatures in the smaller regions and hence leading to the grain refinement in the coarse-grained region of the heat-affected zone.

36 MATERIALS SCIENCE↗

Micromechanisms of grain refinement during extrusion of Mg–0.3 at.% Al at low homologous temperature

Coarse grained Mg–0.3 at.% Al (0.33 in wt.%) alloy was processed by direct extrusion with a reduction ratio of 25:1 at a temperature of ∼ 433 K. The extrusion remainder was removed from the die and analysed in three distinct zones: the cast billet, the conical zone of extrusion die, and the as-extruded rod. The zones were characterized by electron backscatter diffraction (EBSD) and light microscopy techniques to identify the processes responsible for grain refinement. Complex networks of (10–12) twins in practically all grains produced a noticeable microstructural fragmentation even before the material reached the conical zone of the die. Deformation twinning extended up to the entrance zone of the conical die where it was followed by a continuous dynamic recrystallization (CDRX) that gradually changed low angle boundaries to high angle boundaries. It is apparent that geometrically necessary dislocations play a crucial role in the formation of new grain boundaries. CDRX results in a bimodal structure with grain diameters ∼ 3 and ∼ 30 μm. As a material flows through the conical zone, the ratio of large to small grains is progressively decreased by CDRX in favour of fine grains. The as-extruded microstructure (a rod 8 mm in diameter), with an average grain diameter of ∼ 2.1 μm, shows a strong texture where the vast majority of grains (99.99%) have the c-axis oriented at least 30° from the extrusion direction. - Highlights: • Coarse grained Mg–0.3 at.% Al alloy was extruded at temperature of ∼ 433 K. • Processes responsible for grain refinement were analysed in extrusion remainder. • In the first stage, complex (10–12) twinning produced a noticeable fragmentation. • Deformation twinning was followed by continuous dynamic recrystallization. • 99.99% of grains in extruded rod have c-axis oriented > 30° from extrusion direction.

36 MATERIALS SCIENCE↗

Laser shock peening effect on the dislocation transitions and grain refinement of Al–Mg–Si alloy

This paper systematically investigates the effect of laser shock peening without coating parameters on the microstructural evolution, and dislocation configurations induced by ultra-high plastic strains and strain rates. Based on an analysis of optical microscopy, polarized light microscopy, transmission electron microscopy observations and residual stress analysis, the significant influence of laser shock peening parameters due to the effect of plasma generation and shock wave propagation has been confirmed. Although the optical microscopy results revealed no significant microstructural changes after laser shock peening, i.e. no heat effect zone and differences in the distribution of second-phase particles, expressive influence of laser treatment parameters on the laser shock induced craters was confirmed. Moreover, polarized light microscopy results have confirmed the existence of well-defined longish grains up to 455 μm in length in the centre of the plate due to the rolling effect, and randomly oriented smaller grains (20 μm × 50 μm) in the surface due to the static recrystallization effect. Laser shock peening is reflected in an exceptional increase in dislocation density with various configurations, i.e. dislocation lines, dislocation cells, dislocation tangles, and the formation of dense dislocation walls. More importantly, the microstructure is considerably refined due to the effect of strain deformations induced by laser shock peening process. The results have confirmed that dense dislocation structures during ultra-high plastic deformation with the addition of shear bands producing ultra-fine (60–200 nm) and nano-grains (20–50 nm). Furthermore, dislocation density was increased by a factor of 2.5 compared to the untreated material (29 × 10{sup 13} m{sup −2} vs. 12 × 10{sup 13} m{sup −2}). - Highlights: • LSPwC imparts high compressive residual stresses up to − 362 ± 31 MPa. • After LSPwC the microstructure is considerably refined via dislocation transitions. • Results confirmed ultra-fine (60–200 nm) and nano-grains (20–50 nm) after LSPwC. • Reasonable agreements between dislocation density and residual stress are obtained.

36 MATERIALS SCIENCE↗

Surface grain refinement of casting A380 aluminum alloy by ultrasonic-assisted surface mechanical grinding treatment

A novel surface processing technique, ultrasonic-assisted surface mechnical grinding treatment (U-SMGT), was proposed and applied to modify the surface micriostructure of the casting aluminum alloy (A380). Comprehensive post-process chracterization techniques including 3D profilometry, optical microscope, scanning electric microscopy (SEM), and electron backscatter diffraction (EBSD) were carried out to investigate the surface morphology and microstructure of the processed region (PR). It was found that a surface layer of grain refinement with a thickness of about 50 µm was formed. In the as-received base material (BM), large clusters of dendritic eutectic phase with a size of approximately 20 µm were isolated by α-Al matrix. Nano-indentation tests showed that hardness of the eutectic and α-Al in the as-received BM was 2.15 GPa and 1.2 GPa respectively. After U-SMGT, the large dendritic eutectic phase was broken down into much fine particles with an average size of 0.57 µm. These fine particles were uniformly distributed into the α-Al matrix. Nano-indentation measurement exhibited a hardness of 2.27 GPa within the processed region. The overall high hardness in the processed region is a result of the pinning effect of uniformly distributed fine dendrites and grain refinement of Al-matrix.

36 MATERIALS SCIENCE↗

Microstructural refinement of an Al-Ce-Mg alloy via Shear Assisted Processing and Extrusion

Al-Ce alloys have attracted recent interest because of their high thermal stability due to the low solubility of Ce in the Al matrix. The Al 11 Ce 3 eutectic phase gives excellent strain hardening behavior and moderate high-temperature strength in the as-cast state. However, its strengthening effect is limited by its coarse as-cast structure. Therefore, alternative manufacturing methods such as additive manufacturing or equal channel angular pressing have been applied to refine the Al 11 Ce 3 phase to good effect. However, these techniques are both expensive and time-consuming. Therefore, this study aims to use Shear Assisted Processing and Extrusion (ShAPE), an emerging solid phase processing technique that is more easily scalable than the previously mentioned methods. ShAPE can produce useful cross-sections of an Al-8Ce-4Mg alloy while refining the Al 11 Ce 3 phase to produce a higher strength material. It was found that a low temperature ShAPE process can improve the room temperature yield strength by ~60 % compared to a binary Al-4Mg alloy. Additionally, the high-temperature yield strength of the Al-Ce alloys increased by 20%, with a simultaneous 15% improvement in ductility compared to the binary Al-Mg alloy. Finally, these results highlight the potential for ShAPE as a processing technique for Al-Ce alloys.

36 MATERIALS SCIENCE↗

Deacetylation and Mechanical Refining (DMR) and Deacetylation and Dilute Acid (DDA) Pretreatment of Corn Stover, Switchgrass, and a 50/50 Corn Stover/Switchgrass Blend

The most economical feedstock available to future lignocellulosic biorefineries may be a feedstock blend. Corn stover, switchgrass, and a 50:50 blend of corn stover and switchgrass were subjected to three different dilute alkali deacetylation conditions in a 90 L reactor prior to either mechanical refining (DMR) in a disc refiner followed by a Szego mill or dilute acid pretreatment (DDA) at five different conditions in a 4 L batch steam explosion reactor. The forty-five DDA and nine DMR slurries were subjected to high solids enzymatic hydrolysis at an enzyme loading of 15 mg protein per gram cellulose using Novozymes Cellic CTec3 (DDA) or a 4:1 mix of Novozymes Cellic CTec3:HTec 3 (DMR). The highest glucose yield was achieved using DMR processed corn stover from the high severity deacetylation condition (92 °C and 100 kg NaOH/ODMT) at 95.9% ± 0.8%, while the greatest monomeric glucose yields for switchgrass were between 75% to 80%. The glucose yields from saccharification of the 50:50 corn stover/switchgrass blend was approximately the average of the two individual feedstocks for both DDA and DMR processes. Statistical analysis showed that for a given feedstock type dilute alkali deacetylation severity had a significant impact (p < 0.05) on enzymatic hydrolysis yields, and for a given deacetylation severity the feedstock type had a significant effect on glucose conversion with the addition of switchgrass resulting in lower glucose yields. A blending strategy to maximize enzymatic hydrolysis sugar yields while reducing carbohydrate solubilization during the alkaline treatment step was proposed that allows deacetylation of feedstocks with different recalcitrance at optimal conditions for that feedstock, then blending prior to enzymatic hydrolysis.

BIOMASS FUELS,INORGANIC, ORGANIC, PHYSICAL, AND AN↗

Grain Refinement of a gamma-TiAl Alloy Through Isothermal Forging and Heat Treatment

Effect of initial massive type structure of a gamma-TiAl based alloy on its hot deformed and stabilized microstructure was investigated. A gamma alloy with composition of Ti-47Al-12Nb-0.5Si was subjected to rapid quenching from alpha phase field. The quenched sample was deformed at high temperature. Further post deformation heat treatment was conducted to stabilize the as-deformed structure. It was shown that Nb and Si have important roles in grain refinement of the final product. Presence of niobium in the alloy made the diffusion controlled eutectoid reaction sluggish and assisted the formation of massive type gamma phase (gamma{sub m}) by rapid cooling from alpha phase field. Silicon addition assisted the microstructural refinement by forming hard and finely dispersed titanium silicide particles. These particles act as preferred sites for dynamic recrystallization during hot deformation. Massive gamma phase tends to deform uniformly and decompose to equilibrium phases after final heat treatment and results in a very fine grained microstructure.

36 MATERIALS SCIENCE↗

Equal Channel Angular Pressing (ECAP) and Its Application to Grain Refinement of Al-Zn-Mg-Cu Alloy

Microstructure of a metal can be considerably changed by severe plastic deformation techniques such as high pressure torsion, extrusion and equal-channel angular pressing (ECAP). Among these methods, ECAP is particularly attractive because it has a potential for introducing significant grain refinement and homogeneous microstructure into bulk materials. Typically, it reduces the grain size to the submicrometer level or even nanometer range and thus produces materials that are capable of exhibiting unusual mechanical properties. In the present study, a test unites for equal channel angular pressing was constructed and this system was used for Al-Zn-Mg-Cu alloy. After the optimization tests, it was seen that the most effective lubricant for the dies was MoS{sub 2}, the pressing pressure was around 25-35 ton and the pressing speed was 2 mm/s. By using these parameters, the Al-Zn-Mg-Cu alloy was successfully ECAPed up to 14 passes at 200 deg. C using route C. After ECAP tests, the specimens were characterized by transmission electron microscope (TEM), hardness and macrostructural investigations. It was seen that the plastic deformation in the ECAPed specimens occurred from edge to the centre like whirlpool. In addition, the deformation intensity increased with increasing pass number. The grain size of the specimens effectively also decreased with increasing pass number. That is, while the grain size of unECAPed specimen was 10 {mu}m, this value decreased to 300 nm after 14 passes. At the beginning, while there was a banding tendency in the grains toward deformation direction, homogeneous and equiaxed grains were formed with increasing pass number. This grain refinement was as a result of an interaction between shear strain and thermal recovery during ECAP processing. Hardness measurements showed that the hardness values increased up to 4 passes, decreased effectively at 6th pass, again increased at 8th pass and after this pass, the hardness again decreased due to dynamic recrystallization.

36 MATERIALS SCIENCE↗

The purification process on scintillator material (SrI{sub 2}: Eu) by zone-refinement technique

The thermal properties of Europium doped strontium iodide was analyzed through Thermogravimetric (TG) and differential thermal analyses (DTA). The melting point of europium doped strontium iodide is around 531°C. The hydrated and oxyhalide impurities were found before melting temperature. In order to remove these impurities we have done purification process by Zone-refinement technique. The effective output of purification of zone refining was also observed through the segregation of impurities.

36 MATERIALS SCIENCE↗