Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “pattern transfer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

IUE's legacy for the future: The final archive and goals for its implementation

Requirements for the IUE archive, and how the signal/noise (S/N) ratio in photometrically corrected images can be enhanced considerably by cross-correlating the fixed pattern in a data image with that in a suitable flat-field image are described. From these cross-correlations it is feasible to derive an accurate geometrical correction to apply to the data image before applying the intensity transfer functions. The standard IUE processing software does not generate a sufficiently accurate geometric correction so that typical spatial errors of 1 to 2 pixels conspire with the large fixed pattern in raw images to produce significant misregistration noise. Tests on flat-field images demonstrate that an explicit geometric correction procedure can avoid most of the misregistration noise and can thereby improve the S/N ratio of IUE data by factors of 1.5 to 2.4.

Linsky, J. L.↗
NASA NTRS1997

Heat Transfer Measurements on Surfaces with Natural Ice Castings and Modeled Roughness

An experimental method is described to measure and compare the convective heat transfer coefficient of natural and simulated ice accretion roughness and to provide a rational means for determining accretion-related enhanced heat transfer coefficients. The natural ice accretion roughness was a sample casting made from accretions at the NASA Lewis Icing Research Tunnel (IRT). One of these castings was modeled using a Spectral Estimation Technique (SET) to produce three roughness elements patterns that simulate the actual accretion. All four samples were tested in a flat-plate boundary layer at angle of attack in a "dry" wind tunnel test. The convective heat transfer coefficient was measured using infrared thermography. It is shown that, dispite some problems in the current data set, the method does show considerable promise in determining roughness-induced heat transfer coefficients, and that, in addition to the roughness height and spacing in the flow direction, the concentration and spacing of elements in the spanwise direction are important parameters.

Breuer, Kenneth S.↗
NASA NTRS1981

Breadboard stellar tracker system test report, volume 1

The performance of a star tracker equipped with a focal plane detector was evaluated. The CID board is an array of 256 x 256 pixels which are 20 x 20 micrometers in dimension. The tracker used for test was a breadboard tracker system developed by BASD. Unique acquisition and tracking algorithms are employed to enhance performance. A pattern recognition process is used to test for proper image spread function and to avoid false acquisition on noise. A very linear, high gain, interpixel transfer function is derived for interpolating star position. The lens used in the tracker has an EFL of 100 mm. The tracker has an FOV of 2.93 degrees resulting in a pixel angular subtense of 41.253 arc sec in each axis. The test procedure used for the program presented a star to the tracker in a circular pattern of positions; the pattern was formed by projecting a simulated star through a rotatable deviation wedge. Further tests determined readout noise, Noise Equivalent Displacement during track, and spatial noise during acquisition by taking related data and reducing it.

Kollodge, J. C.↗
NASA NTRS1991

Experimental investigation of the flow field in the head-end star slot section of a solid rocket motor

A test program has been developed to investigate the complex flowfield in the head-end, star grain section of a solid rocket motor. Documentation of the flowfield pattern is to be obtained using both flow visualization techniques and quantitative methods, including static pressure measurements, heat transfer coefficient measurements, and hot-wire anemometry. A cold-flow, one-tenth-scale model based on the geometry of the Space Shuttle SRM head-end section and its single-port igniter, along with two models of a four-port igniter, have been constructed. The scale factor is derived from a scaling analysis which matches Reynolds number between the model and the full-scale flowfield in the star grain section. The NASA Marshall Space Flight Center 14 x 14 inch trisonic wind tunnel will be utilized for the cold flow tests. Since the work is still in progress, no results are included.

Ciucci, A.↗
NASA NTRS1992

Spatial and temporal variations of the fluxes of carbon dioxide and sensible and latent heat over the FIFE site

Airborne measurements of flux densities of carbon dioxide CO2, sensible heat, and latent heat (H2O) obtained over the First ISLSCP Field Experiment (FIFE) site during three intensive field campaigns in 1987 and one in 1989 are examined to characterize the spatial and temporal variations of CO2 and energy transfer processes. These data were collected by the National Research Council Twin Otter using low-level flight patterns, all flown at constant pressure altitude during relatively clear days. The spatial variations are larger in 1989 than in 1987 and a higher correlation is observed between the fluxes and the surface features. The temporal patterns are easier to characterize with the relatively homogeneous situation of 1987. Functional relationships obtained between fluxes of CO2 and latent heat, CO2 fluxes and greenness index, latent heat fluxes and greenness index, and between sensible heat fluxes and surface air temperature differences are presented for one day in 1987 and one in 1989 as an example of the kind of information that can be obtained from grid flights at constant pressure altitude.

Desjardins, R. L.↗
NASA NTRS1993

RAID 7 disk array

Each RAID level reflects a different design architecture. Associated with each is a backdrop of imposed limitations, as well as possibilities which may be exploited within the architectural constraints of that level. There are three unique features that differentiate RAID 7 from all other levels. RAID 7 is asynchronous with respect to usage of I/O data paths. Each I/O drive (includes all data and one parity drives) as well as each host interface (there may be multiple host interfaces) has independent control and data paths. This means that each can be accessed completely, independently, of the other. This is facilitated by a separate device cache for each device/interface as well. RAID 7 is asynchronous with respect to device hierarchy and data bus utilization. Each drive and each interface is connected to a high speed data bus controlled by the embedded operating system to make independent transfers to and from central cache. RAID 7 is asynchronous with respect to the operation of an embedded real time process oriented operating system. This means that exclusive and independent of the host, or multiple host paths, the embedded OS manages all I/O transfers asynchronously across the data and parity drives. A key factor to consider is that of the RAID 7's ability to anticipate and match host I/O usage patterns. This yields the following benefits over RAID's built around micro-code based architectures. RAID 7 appears to the host as a normally connected Big Fast Disk (BFD). RAID 7 appears, from the perspective of the individual disk devices, to minimize the total number of accesses and optimize read/write transfer requests. RAID 7 smoothly integrates the random demands of independent users with the principles of spatial and temporal locality. This optimizes small, large, and time sequenced I/O requests which results in users having an I/O performance which approaches performance to that of main memory.

Stout, Lloyd↗
NASA NTRS1987

Use of simulated satellite radiances from a mesoscale numerical model to understand kinematic and dynamic processes

Techniques by which mesoscale numerical weather prediction model output and radiative transfer codes are combined to simulate the radiance fields that a given passive temperature/moisture satellite sensor would see if viewing the evolving model atmosphere are introduced. The goals are to diagnose the dynamical atmospheric processes responsible for recurring patterns in observed satellite radiance fields, and to develop techniques to anticipate the ability of satellite sensor systems to depict atmospheric structures and provide information useful for numerical weather prediction (NWP). The concept of linking radiative transfer and dynamical NWP codes is demonstrated with time sequences of simulated radiance imagery in the 24 TIROS vertical sounder channels derived from model integrations for March 6, 1982.

Kalb, Michael↗
NASA NTRS1982

Interpretation of satellite-observed thunderstorm anvil structure

The radiative characteristics of an anvil plume sensed by satellite radiometers are studied to discern the reason for an observed 'V' pattern of colder temperatures and a corresponding internal warm region. The measured black body temperature is affected by the ice water content and particle distributions in the cloud layer. Attention is given to 'V' anvil structure examined by Haynesfield et al. (1979). The GOES satellite IR data are treated with a plane parallel geometric radiative transfer model and a particle trajectory model is used to simulate ice particle concentrations downwind from a strongly divergent cloud top. Output from the two models indicate the 'V' pattern arises from divergence in the storm anvil. The particle concentration was elevated within the V-shaped region, causing lower temperatures in the V arms. The V is produced by strong upper level flow as well as strong mass and moisture divergence in the storm outflow.

Heymsfield, G. M.↗
NASA NTRS1997

Precision Casting via Advanced Simulation and Manufacturing

A two-year program was conducted to develop and commercially implement selected casting manufacturing technologies to enable significant reductions in the costs of castings, increase the complexity and dimensional accuracy of castings, and reduce the development times for delivery of high quality castings. The industry-led R&D project was cost shared with NASA's Aerospace Industry Technology Program (AITP). The Rocketdyne Division of Boeing North American, Inc. served as the team lead with participation from Lockheed Martin, Ford Motor Company, Howmet Corporation, PCC Airfoils, General Electric, UES, Inc., University of Alabama, Auburn University, Robinson, Inc., Aracor, and NASA-LeRC. The technical effort was organized into four distinct tasks. The accomplishments reported herein. Task 1.0 developed advanced simulation technology for core molding. Ford headed up this task. On this program, a specialized core machine was designed and built. Task 2.0 focused on intelligent process control for precision core molding. Howmet led this effort. The primary focus of these experimental efforts was to characterize the process parameters that have a strong impact on dimensional control issues of injection molded cores during their fabrication. Task 3.0 developed and applied rapid prototyping to produce near net shape castings. Rocketdyne was responsible for this task. CAD files were generated using reverse engineering, rapid prototype patterns were fabricated using SLS and SLA, and castings produced and evaluated. Task 4.0 was aimed at developing technology transfer. Rocketdyne coordinated this task. Casting related technology, explored and evaluated in the first three tasks of this program, was implemented into manufacturing processes.

Source record↗
NASA NTRS2001

High Earth Orbit Design for Lunar-Assisted Medium Class Explorer Missions

This study investigates the application of high-Earth orbit (HEO) trajectories to missions requiring long on-target integration times, avoidance of the Earth's radiation belt, and minimal effects of Earth and Lunar shadow periods which could cause thermal/mechanical stresses on the science instruments. As used here, a HEO trajectory is a particular solution to the restricted three-body problem in the Earth-Moon system with the orbit period being either 1/2 of, or 1/4 of, the lunar sidereal period. A primary mission design goal is to find HEO trajectories where, for a five-year mission duration, the minimum perigee radius is greater than seven Earth radii (R(sub E)). This minimum perigee radius is chosen so that, for the duration of the mission, the perigee is always above the relatively heavily populated geosynchronous radius of 6.6 R(sub E). A secondary goal is to maintain as high an ecliptic inclination as possible for the duration of the mission to keep the apsis points well out of the Ecliptic plane. Mission design analysis was completed for launch dates in the month of June 2003, using both direct transfer and phasing loop transfer techniques, to a lunar swingby for final insertion into a HEO. Also provided are analysis results of eclipse patterns for the trajectories studied, as well as the effects of launch vehicle errors and launch delays.

McGiffin, Daniel A.↗
NASA NTRS1981

Streamwise flow and heat transfer distributions for jet array impingement with crossflow

Two-dimensional arrays of circular jets of air impinging on a heat transfer surface parallel to the jet orifice plate are considered. The air, after impingement, is constrained to exit in a single direction along the channel formed by the surface and the jet plate. The downstream jets are subjected to a crossflow originating from the upstream jets. Experimental and theoretical results obtained for streamwise distributions of jet and crossflow velocities are presented and compared. Measured Nusselt numbers resolved to one streamwise hole spacing are correlated with individual spanwise row jet Reynolds numbers and crossflow-to-jet velocity ratios. Correlations are presented for both inline and staggered hole patterns including effects of geometric parameters: streamwise hole spacing, spanwise hole spacing, and channel height, normalized by hole diameter. The physical mechanisms influencing heat transfer coefficients as a function of flow distribution and geometric parameters are also discussed.

Florschuetz, L. W.↗
NASA NTRS1991

The effect of a type 3 and type 4 shock/shock interaction on heat transfer in the stagnation region

One of the major engineering challenges in designing the National Aerospace Plane, NASP, is to overcome augmented heating on the intake cowl lip from shock/shock interactions. The shock/shock interaction arises when the bow shock from the craft's nose interferes with the bow shock from the cowl lip. Considering only the region immediately around the cowl lip, the problem geometry may be simplified as that of an oblique shock impinging on a bow shock from a circular cylinder. Edney classified six different interference patterns resulting from an oblique-shock/curved bow-shock interaction. Of these six types, type 3 and 4 are most significant in that augmented surface heat transfer may be ten to thirty times greater than the case without the shock/shock interaction. The objective was to begin to develop a mathematical model which is capable of predicting the effect of a type 3 and 4 shock/shock interaction in the stagnation region of an arbitrary 2-D body. This model must be capable of predicting the maximum surface heat flux and the surface stagnation point pressure once the outer (effectively inviscid) flowfield is given. Therefore, it must capture the unsteady physics of the impinging shear layer.

Wilson, Dennis↗
NASA NTRS1964

Discussion of the General Electric proposal to develop a computer program to select thermal coatings for passive temperature control of satellites

The General Electric Company, Missiles and Space Division, submitted/a proposal to NASA for the development of an IBM 7094 computer program which would select the exterior surface coatings for passively controlling spacecraft temperatures. G. E. claims that the "trial and error" procedures currently used can be accomplished more rationally and can therefore be programmed for a digital computer. In the ASME paper, 63-HT-41, which was presented at the ASME-AIChE Heat Transfer Conference at Boston in August, 1963, Costello, Harper, and Cline, described the procedures that have been used at G. E. to develop a coating selection program subject to the following restrictions: 1. Steady-state conditions prevail, 2. Heat transfer occurs by radiation only, 3. Temperatures are optimized at only one interior point in the spacecraft, an d 4. Only the solar absorptance of the external coatings is varied to optimize temperature. The emittance must remain constant at initially specified values. General Electric proposes to develop a generalized program in three steps: 1. The program would vary both solar absorptance and hemispherical emittance to obtain the optimum coating patterns; 2. Temperatures would be optimized at more than one interior point; and 3. The equations would be modified to account for both conduction and radiation heat transfer. In the development of the general program, the scope would be restricted to steady-state heat transfer. Since the thermal designs of most spacecraft are based primarily on nearly equilibrium conditions, the proposed program could have wide application. An obvious extension of the proposed program would be to account for transient temperatures.

IBM 7090 COMPUTER↗
NASA NTRS2020

Hexcomb Pattern Roughness Effects on Blunt Body Transition and Heating

An experimental investigation of hexcomb pattern surface roughness effects on boundary-layer transition and convective heating has been performed. Two representative entry vehicle geometries, a spherical-cap aeroshell and a sphere-cone aeroshell, were considered. Multiple cast ceramic models of each geometry were fabricated with various roughness pattern densities and depths that simulated an ablated hexcomb-structure thermal protection system. Wind tunnel testing was performed at Mach 6 over a range of Reynolds numbers sufficient to produce laminar, transitional, and turbulent flow. Aeroheating and boundary-layer transition onset data were obtained using global phosphor thermography. The experimental heating data are presented herein, as are comparisons to laminar and turbulent smooth-wall heat transfer distributions from computational flow field simulations. The experimental data were used to develop a unified boundary-layer transition correlation for both sandgrain distributed roughness and hexcomb pattern roughness.

Brian R Hollis↗
NASA NTRS1992

Dynamics of the Venus atmosphere

The superrotation of the Venus atmosphere is a major unanswered problem in planetary science. At cloud-top levels (65-70 km altitude) the atmosphere rotates with a five-day period, corresponding to an equatorial wind speed of 90 m/s. Angular velocity is roughly constant on spherical shells, and decreases linearly with altitude to zero at the surface. The direction of rotation is the same as that of the solid planet, which is retrograde--opposite to the direction of orbital motion, but the 5-day period is short compared to the 243-day spin period of the solid planet or to the mean solar day, which is 117 Earth-days at the surface. The problem with the superrotation is that shearing stresses tend to transfer angular momentum downward, and would slow the atmosphere until it is spinning with the solid planet. Some organized circulation pattern is counteracting the tendency, but the pattern has not been identified. A simple Hadley-type circulation cannot do it because such a circulation is zonally symmetric and Hide's Theorem states that in an axisymmetric circulation an extremum in angular momentum per unit mass M can exist only at the surface. Venus violates the last condition, having a maximum of retrograde M on the equator at 70-80 km altitude. This leaves waves and eddies to maintain the superrotation but the length scales and forcing mechanisms for these motions need to be specified. Possible forcing mechanisms associated with waves, eddies and tides are discussed.

Ingersoll, A. P.↗
NASA NTRS1992

Effect of impact angle on central-peak/peak-ring formation and crater collapse on Venus

Although asymmetry in ejecta patterns and craters shape-in-plan are commonly cited as diagnostic features of impact angle, the early-time transfer of energy from impactor to target also creates distinctive asymmetries in crater profile with the greatest depth uprange. In order to simulate gravity-controlled crater-growth, laboratory experiments use loose particulate targets as analogs for low-strength material properties following passage of the shock. As a result, impact crater diameter D in laboratory experiments generally is many times greater than the impactor diameter 2r (factor of 40), and early-time asymmetries in energy transfer from oblique impacts are consumed by subsequent symmetrical crater growth, except at the lowest angles (less than 25 deg). Such asymmetry is evident for oblique (less than 60 deg from horizontal) impacts into aluminum where D/2r is only 2 to 4. Because cratering efficiency decreases with increasing crater size and decreasing impact angle, large scale planetary craters (4080 km) should have transient excavation diameters only 6-10 times larger than the impactor. At basin scales, D/2r is predicted to be only 3-5, i.e., approaching values for impacts into aluminum in laboratory experiments. As a result, evidence for early-time asymmetry in impactor energy transfer should become evident on planetary surfaces, yet craters generally retain a circular outline for all but the lowest impact angles.

Schultz, Peter H.↗
NASA NTRS1993

Investigation of a hypersonic crossing shock wave/turbulent boundary layer interaction

A combined theoretical and experimental study is presented for the interaction between crossing shock waves generated by (10 deg, 10 deg) sharp fins and a flat plate turbulent boundary layer at Mach 8.3. The theoretical model is the full 3D mean compressible Reynolds-averaged Navier-Stokes (RANS) equations incorporating the algebraic turbulent eddy viscosity model of Baldwin and Lomax (1978). A grid refinement study indicated that adequate resolution of the flow field has been achieved. Computed results agree well with experiment for surface pressure and surface flow patterns and for pitot pressure and yaw angle profiles in the flow field. The computations, however, significantly overpredict surface heat transfer. Analysis of the computed flow field results indicates the formation of complex streamline and wave structures within the interaction region.

Narayanswami, N↗
NASA NTRS2001

Predicting Turbulent Convective Heat Transfer in Fully Developed Duct Flows

The performance of an explicit algebraic stress model (EASM) is assessed in predicting the turbulent flow and forced heat transfer in both straight and wavy ducts, with rectangular, trapezoidal and triangular cross-sections, under fully developed conditions. A comparison of secondary flow patterns. including velocity vectors and velocity and temperature contours, are shown in order to study the effect of waviness on flow dynamics, and comparisons between the hydraulic parameters. Fanning friction factor and Nusselt number, are also presented. In all cases. isothermal conditions are imposed on the duct walls, and the turbulent heat fluxes are modeled using gradient-diffusion type models. The formulation is valid for Reynolds numbers up to 10(exp 5) and this minimizes the need for wall functions that have been used with mixed success in previous studies of complex duct flows. In addition, the present formulation imposes minimal demand on the number of grid points without any convergence or stability problems. Criteria in terms of heat transfer and friction factor needed to choose the optimal wavy duct cross-section for industrial applications among the ones considered are discussed.

Rokni, Masoud↗