Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oscillatory response”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Oscillatory burning of solid propellants including gas phase time lag.

An analysis has been performed for oscillatory burning of solid propellants including gas phase time lag. The gaseous flame is assumed to be premixed and laminar with a one-step overall chemical reaction. The propellant is assumed to decompose according to the Arrenhius Law, with no condensed phase reaction. With this model, strong gas phase resonance has been found in certain cases at the characteristic gas-phase frequencies, but the peaking of the acoustic admittance is in the direction favoring the damping of pressure waves. At still higher frequencies, moderate wave-amplifying ability was found. The limit of low frequency response obtained previously by Denison and Baum was recovered, and the limitations of the quasi-steady theory were investigated.

T'Ien, J. S.↗
DOE OSTI2024

Strain shift measured from stress-controlled oscillatory shear: Evidence for a continuous yielding transition and new techniques to determine recovery rheology measures

Understanding the yielding of complex fluids is an important rheological challenge that affects our ability to engineer and process materials for a wide variety of applications. Common theoretical understandings of yield stress fluids follow the Oldroyd–Prager formalism in which the material behavior below the yield stress is treated as solidlike, and above the yield stress as liquidlike, with an instantaneous transition between the two states. This formalism was built on a quasi-static approach to the yield stress, while most applications, ranging from material processing to end user applications, involve a transient approach to yielding over a finite timescale. Using stress-controlled oscillatory shear experiments, we show that yield stress fluids flow below their yield stresses. This is quantified through measuring the strain shift, which is the value about which the strain oscillates during a stress-controlled test and is a function of only the unrecoverable strain. Measurements of the strain shift are, therefore, measurements of flow having taken place. These experimental results are compared to the Herschel–Bulkley form of the Saramito model, which utilizes the Oldroyd–Prager formalism, and the recently published Kamani–Donley–Rogers (KDR) model, in which one constitutive equation represents the entire range of material responses. Scaling relationships are derived, which allow us to show why yield stress fluids will flow across all stresses, above and below their yield stress. Finally, derivations are presented that show strain shift can be used to determine average metrics previously attainable only through recovery rheology, and these are experimentally verified.

Mechanics↗
NASA NTRS1983

A study of helicopter gust response alleviation by automatic control

Two control schemes designed to alleviate gust-induced vibration are analytically investigated for a helicopter with four articulated blades. One is an individual blade pitch control scheme. The other is an adaptive blade pitch control algorithm based on linear optimal control theory. In both controllers, control inputs to alleviate gust response are superimposed on the conventional control inputs required to maintain the trim condition. A sinusoidal vertical gust model and a step gust model are used. The individual blade pitch control, in this research, is composed of sensors and a pitch control actuator for each blade. Each sensor can detect flapwise (or lead-lag or torsionwise) deflection of the respective blade. The acturator controls the blade pitch angle for gust alleviation. Theoretical calculations to predict the performance of this feedback system have been conducted by means of the harmonic method. The adaptive blade pitch control system is composed of a set of measurements (oscillatory hub forces and moments), an identification system using a Kalman filter, and a control system based on the minimization of the quadratic performance function.

Saito, S.↗
NASA NTRS1978

Experiments on the dynamic behavior of cavitating pumps

This paper describes experiments performed to measure the dynamic transfer matrices for cavitating (and noncavitating) pumps. These transfer matrices describe the relationship between small linear oscillatory perturbations in the pressures and mass flow rates at inlet and discharge from the hydraulic machine. The matrices were deduced from direct measurements of these fluctuating quantities for different modes of excitation of the machine. Results for a cavitating inducer are presented as functions of frequency and mean operating state. Though some of the trends in the data are consistent with existing theoretical models of inducer dynamics, others are not, indicating a need for further theoretical investigation of the dynamic characteristics of such flows. The results exhibit increasingly complex dynamics with increasing cavitation; it appears that the hydraulic machine deviates from an essentially passive response without cavitation to an increasingly active response as the cavitation number is reduced.

Ng, S. L.↗
NASA NTRS1993

Modeling of PCG fluid dynamics: Salient results

Materials processing in space-based laboratories has already yielded higher quality crystals during previous space flights, and opportunities for several fluids experiments are anticipated during the extended duration missions planned for the future. Crystal growth in space benefits not only from its reduced gravity environment but also from the absence of the hydrostatic pressure which assists certain crystal growth and refinement methods. Gravity-driven phenomena are thus reduced in strength, and a purely diffusive fluid's behavior can be attained. In addition, past materials science experiments have shown that microgravity can also help produce larger crystals. While gravity-related effects are definitely curtailed in space, they are nevertheless present to some degree due to the acceleration environment onboard the spacecraft. This residual acceleration level is comprised of quasi-steady, oscillatory, and transient components, and is caused by a variety of mechanisms. For example, gravity gradient forces produce low frequency disturbances, and the operation of machinery, control thrusters, solar panels, human activity, etc. contribute to higher frequency accelerations. These disturbances are collectively referred to as g-jitter, and they can be deleterious to certain experiments where the minimization of the acceleration level is important. Advanced vibration isolation techniques can be utilized to actively filter out some of the detrimental frequencies and help in obtaining optimum results. However, the successful application of this technology requires the detailed analysis of candidate fluids experiments to gauge their response to g-jitter and to determine their acceleration sensitivities. Several crystal growth experiments in the Protein Crystal Growth (PCG) area, besides others, are expected to be carried out on future shuttle flights and on Space Station Freedom. The need for vibration isolation systems or components for microgravity science experiments can be expected to grow as experiments and available hardware becomes more complex. This technology will also find increased application as the science community develops an awareness of their specific needs relative to the environment available in manned space missions. Vibration isolation research strives to develop a microgravity environment requirement that defines tolerance limits on the allowable g-level, and provides the required technology to achieve it. This effort will assist in establishing the tolerable acceleration levels for specific fluids experiments. The primary effort is directed towards modeling PCG and the approach undertaken for this investigation is outlined. The objectives of this research are: (1) to computationally determine vibration sensitivity of protein crystal growth experiments; (2) determine if these experiments can benefit from vibration isolation techniques; and (3) provide realistic requirements for vibration isolation technology.

Ramachandran, N.↗
DOE OSTI2020

Tuning the dynamics of imidazolium-based ionic liquids via hydrogen bonding. I. The viscous regime

Combining results from impedance spectroscopy and oscillatory shear rheology, this study focuses on the relation between the mass and charge flows and on how these are affected by the H-bonding in viscous ionic liquids (ILs). In particular, we compare the relaxational behaviors of the paradigmatic IL 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (EMIM-TFSI) and its OH-functionalized counterpart 1-(2-hydroxyethyl)-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (OHEMIM-TFSI). Our results and their analysis demonstrate that the presence of cationic OH-groups bears a strong impact on the overall dynamics of OHEMIM-TFSI, although no signatures of suprastructural relaxation modes could be identified in their dielectric and mechanical responses. To check whether at the origin of this strong variation is the H-bonding or merely the difference between the corresponding cation sizes (controlling both the hydrodynamic volume and the inter-charge distance), the present study includes 1-propyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (PMIM-TFSI), mixtures of EMIM-TFSI and PMIM-TFSI with lithium bis(trifluoromethylsulfonyl)imide (Li-TFSI), and mixtures of OHEMIM-TFSI with PMIM-TFSI. Their investigation clearly reveals that the dynamical changes induced by H-bonding are significantly larger than those that can be attributed to the change in the ion size. Moreover, in the mixtures of OHEMIM-TFSI with PMIM-TFSI, a dilution of the OH-groups leads to strong deviations from ideal mixing behavior, thus highlighting the common phenomenological ground of hydroxy-functionalized ILs and other H-bonded liquids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2003

Sera from cancer patients contain two oscillating ECTO-NOX activities with different period lengths

ECTO-NOX protein's are cell surface-associated and growth-related hydroquinone oxidases with both protein disulfide-thiol interchange activity and the capacity to oxidize NAD(P)H. The activities of these ECTO-NOX proteins are not steady state but fluctuate to create a repeating pattern of oscillations. Two forms of ECTO-NOX activities have been distinguished. The constitutive ECTO-NOX (CNOX), is hormone responsive and refractory to quinone-site inhibitors. A tumor-associated NOX (tNOX) is unregulated, refractory to hormones and growth factors and responds to quinone-site inhibitors. CNOX proteins are widely distributed and exhibit oscillations in enzymatic activity with a period length of 24 min. tNOX proteins are cancer specific and exhibit oscillations with a period length of about 22 min. Our findings now demonstrate the presence of the novel oscillating tNOX activity in sera of patients with cancer whereas the constitutive NOX of non-cancer cells is present in sera of both cancer patients and healthy volunteers. We conclude that ECTO-NOX proteins in sera exhibit oscillatory characteristics similar to those of ECTO-NOX forms of the cell surface.

NASA Discipline Cell Biology↗
DOE OSTI2026

A finite viscoelastic constitutive model for low to high strain rate response of elastomers with application of strain rate-induced glass transition

Amorphous elastomers exhibit significant rate-stiffening and unique viscous flow characteristics across a wide range of strain rates, often undergoing glass transition above a strain rate threshold. We have developed a thermodynamically-consistent and micromechanically-inspired constitutive model for soft elastomeric materials to capture the rate-dependent stress-strain behavior and hysteresis when subjected to low to high strain rates. Here, our proposed constitutive model encapsulates the viscous flow of materials through molecular motion at low strain rates and local rearrangement and alignment of the molecules trying to overcome the intermolecular resistance at high strain rates, essentially covering the glass transition. We applied our constitutive model to uniaxial compression experiments performed at low and high strain rates for polyborosiloxane (PBS) to identify the material parameters, and subsequently, performed numerical simulations of single and multi-cycle compression, stress relaxation, and small amplitude oscillatory tension-compression. Our analyses indicate that the model predicts higher total energy dissipation with increasing strain rate; however, dissipation associated with molecular relaxation decreases (forming a cusp) because, beyond a crossover strain rate, intermolecular rearrangement and alignment become dominant, which is consistent with the onset of the glass transition. For cyclic loading-unloading, we observed that dissipation over a cycle remains constant at low strain rates but decreases non-monotonically at high strain rates before becoming constant, with the peak stress over the cycle becoming higher, which can be interpreted as more loading being carried elastically by the polymer network as the intermolecular rearrangement process occurs. Additionally, our model was able to predict the qualitative nature of the storage modulus and loss modulus in the limit of small strain over a wide range of frequency sweeps.

36 MATERIALS SCIENCE↗
NASA NTRS2000

Separation Control at Flight Reynolds Numbers: Lessons Learned and Future Directions

Active separation control, using periodic excitation, was studied experimentally at high Reynolds numbers. The effects of compressibility, mild sweep, location o excitation slot and steady momentum transfer on the efficacy of the method were identified. Tests conducted at chord Reynolds numbers as high as 40 x 10(exp 6) demonstrated that active control using oscillatory flow excitation can effectively delay flow separation from and reattach separated flow to aerodynamic surfaces at flight conditions. The effective frequencies generate one to four vortices over the controlled region at all times, regardless of the Reynolds number. The vortices are initially amplified by the separated shear-layer, and after initiating reattachment, the strength of the vortices decay as they are convected downstream. Large amplitude, low frequency vortices break down to smaller ones upon introduction at the excitation slot. The effects of steady mass transfer were compared to those of periodic excitation. It was found that steady blowing is significantly inferior to periodic excitation in terms o performance benefits and that the response to steady blowing is abrupt, and therefore undesirable from a control point of view. Steady suction and periodic excitation are comparable in effectiveness and both exhibit a gradual response to changes in the magnitude of the control input. The combination of weak steady suction and periodic excitation is extremely effective while the addition of steady blowing could be detrimental. Compressibility effects are weak as long as separation is not caused by a shock-wave/boundary-layer interaction The undesirable effects of the shock-induced separation could be alleviated by the introduction of periodic excitation upstream of the shock wave, inside the region of supersonic flow. The effects of mild sweep were also studied and periodic excitation was found to be very effective in reattaching three-dimensional separated flow. Scaling laws that correlate 2D and 3D controlled flows were tested and verified. Several performance benefits could be gained by applying the method to existing configurations, but it is expected that the full potential of the method can only be realized through the design of new configurations. A comprehensive, fully turbulent, database was generated in order to guide the development, and enable validation, of candidate unsteady CFD design tools.

Seifert, Avi↗
NASA NTRS2000

Separation Control at Flight Reynolds Numbers: Lessons Learned and Future Directions

Active separation control, using periodic excitation, was studied experimentally at high Reynolds numbers. The effects of compressibility, mild sweep, location of excitation slot and steady momentum transfer on the efficacy of the method were identified. Tests conducted at chord Reynolds numbers as high as 40 x 10(exp 6) demonstrated that active control using oscillatory flow excitation can effectively delay flow separation from, and reattach separated flow to aerodynamic surfaces at flight conditions. The effective frequencies generate one to four vortices over the controlled region at all times, regardless of the Reynolds number. The vortices are initially amplified by the separated shear-layer, and after initiating reattachment, the strength of the vortices decay as they are convected downstream. Large amplitude, low frequency vortices break down to smaller ones upon introduction at the excitation slot. The effects of steady mass transfer were compared to those of periodic excitation. It was found that steady blowing is significantly inferior to periodic excitation in terms of performance benefits and that the response to steady blowing is abrupt, and therefore undesirable from a control point of view. Steady suction and periodic excitation are comparable in effectiveness and both exhibit a gradual response to changes in the magnitude of the control input. The combination of weak steady suction and periodic excitation is extremely effective while the addition of steady blowing could be detrimental. Compressibility effects are weak as long as separation is not caused by a shock-wave/boundary-layer interaction. The undesirable effects of the shock-induced separation could be alleviated by the introduction of periodic excitation upstream of the shock wave, inside the region of supersonic flow. The effects of mild sweep were also studied and periodic excitation was found to be very effective in reattaching three-dimensional separated flow. Scaling laws that correlate 2D and 3D controlled flows were tested and verified. Several performance benefits could be gained by applying the method to existing configurations, but it is expected that the full potential of the method can only be realized through the design of new configurations. A comprehensive, fully turbulent, database was generated in order to guide the development, and enable validation, of candidate unsteady CFD design tools.

Pack, LaTunia G.↗
DOE OSTI2024

Analyzing the Effects of Atmospheric Turbulent Fluctuations on the Wake Structure of Wind Turbines and Their Blade Vibrational Dynamics

In recent trends, a rising demand for renewable energy has driven wind turbines to larger proportions, where lighter blade designs are often adopted to reduce the costs associated with logistics and production. This causes modern utility-scale wind turbine blades to be inherently more flexible, and their amplified aeroelastic sensitivity results in complex multi-physics reactions to variant atmospheric conditions, including dynamic patterns of aerodynamic loading at the rotor and vortex structure evolutions within the wake. In this paper, we analyze the influence of inflow variance for wind turbines with large, flexible rotors through simulations of the National Rotor Testbed (NRT) turbine, located at Sandia National Labs’ Scaled Wind Farm Technology (SWiFT) facility in Lubbock, Texas. The Common Ordinary Differential Equation Framework (CODEF) modeling suite is used to simulate wind turbine aeroelastic oscillatory behavior and wind farm vortex wake interactions for a range of flexible NRT blade variations, operating in differing conditions of variant atmospheric flow. CODEF solutions of turbine operation in Steady-In-The-Average (SITA) wind conditions are compared to SITA wind conditions featuring a controlled gust-like pulse overimposed, to isolate the effects of typical wind fluctuations. Finally, simulations of realistic time-varying wind conditions from SWiFT meteorological tower measurements are compared to the solutions of SITA wind conditions. These increasingly complex atmospheric inflow variations are tested to show the differing effects evoked by various patterns of spatiotemporal atmospheric flow fluctuations. An analysis is presented for solutions of wind turbine aeroelastic response and vortex wake evolution, to elucidate the consequences of variant inflow, which pertain to wind turbine dynamics at an individual and farm-collective scale. The comparisons of simulated farm flow for SITA and measured fluctuating wind conditions show that certain regions of the wake contain up to a 12% difference in normalized axial velocity, due to the introduction of wind fluctuations. The findings of this study prove valuable for practical applications in wind farm control and optimization strategies, with particular significance for modern utility-scale wind power plants operating in variant atmospheric conditions.

Farrell, Alayna (ORCID:000000023555720X)↗
NASA NTRS1982

Dynamics of an unsteady turbulent boundary layer

The present investigation is concerned with the response of a well-defined, steady, flatplate turbulent boundary layer subjected subsequently to two types of oscillations of the free-stream velocity in the test section. It is found that the mean velocity profile in the boundary layer is unaffected by imposed free-stream oscillations in the range of frequencies employed. It is the same as the one measured with a free-stream velocity distribution held steady at its mean value. The behavior of the mean velocity field is a consequence of two observations. The time-averaged Reynolds stress distribution across the boundry layer is unaffected by the imposed oscillations. The Reynolds stresses arising from the organized velocity fluctuations under imposed oscillatory conditions are negligible compared to Reynolds stress due to the random fluctuations.

Parikh, P. G.↗
NASA NTRS1971

Examination of the anomalous behavior of three gravity gradient satellites

The anomalous oscillatory behavior of three satellites was examined. The satellites were all hinged, two-body, gravity gradient configurations passively stabilized about their three principal axes by gravity gradient and damper torques. Two basic behavior patterns were observed. Either the satellites were stable with attitude perturbations less than + or - 5 deg or their behavior tended towards a low frequency rigid body oscillation dominated by large yaw motions and in some cases by yaw inversions. A causal relationship between sun angle and the character of satellite behavior was observed which appears to indicate that thermal distortion is a critical factor in a gravity gradient satellite's dynamic behavior. The behavior appeared to be futher modified by the existence of response frequencies that were higher than anticipated values.

Goldman, R. L.↗
DOE OSTI2025

Dual roles of stepped surfaces: Catalytic initiators and stabilizers of oxygen-induced reconstructions

Understanding surface restructuring under reactive conditions is crucial for designing next-generation catalysts with enhanced activity and selectivity. Here, we employ in situ transmission electron microscopy to directly observe the dynamic behavior of Cu(100) and Cu(410) surfaces under both oxidizing and vacuum annealing conditions, revealing a complex interplay among surface crystallography, local oxygen coverage, Cu atom mobility, and step-edge reactivity. The stepped Cu(410) surface acts as an active site for O 2 dissociation, triggering the oscillatory transformation of the c(2 × 2)–O phase into the more stable (2$\sqrt2$ ×$\sqrt2$)R45°–O missing-row (MR) structure on the adjacent flat Cu(100) terrace. Under subsequent vacuum annealing, this same Cu(410) facet exhibits remarkable structural resilience, preserving the MR reconstruction and chemisorbed oxygen. In contrast, the Cu(100) surface undergoes reversible transitions from the MR structure back to the c(2 × 2)–O phase. These results highlight the critical role of surface morphology in directing both the formation and stability of oxygen-induced reconstructions, demonstrating that stepped surfaces serve dual roles as both catalytic initiators and structural stabilizers. Furthermore, this work offers atomic-level insights into the environment-responsive behavior of copper surfaces, establishing a mechanistic basis for designing Cu-based catalysts through facet-specific control of surface reactivity.

36 MATERIALS SCIENCE↗
NASA NTRS1994

Real-time RMS active damping augmentation: Heavy and very light payload evaluations

Controls-Structures Integration Technology has been applied to the Space Shuttle Remote Manipulator System (RMS) to improve on-orbit performance. The objective was to actively damp undesired oscillatory motions of the RMS following routine payload maneuvering and Shuttle attitude control thruster firings. Simulation of active damping was conducted in the real-time, man-in-the-loop Systems Engineering Simulator at NASA's Johnson Space Center. The simulator was used to obtain qualitative and quantitative data on active damping performance from astronaut operators. Using a simulated three-axis accelerometer mounted on the RMS, 'sensed' vibration motions were used to generate joint motor commands that reduced the unwanted oscillations. Active damping of the RMS with heavy and light attached payloads was demonstrated in this study. Five astronaut operators examined the performance of active damping following operator commanded RMS maneuvers and Shuttle thruster firings. Noticeable improvements in the damping response of the RMS with the heavy, Hubble Space Telescope payload and the very light, astronaut in Manipulator Foot Restraint payload were observed. The potential of active damping to aid in precisely maneuvering payloads was deemed significant.

Demeo, Martha E.↗
NASA NTRS1990

Low-frequency cloud-radiation interactions

The observed 30 to 60 day oscillation of the tropical winds, often referred to as the Madden Julian (MJ) oscillation, has excited lots of interest in recent years, because its existence suggests the possibility that the behavior of the atmosphere is at least partially predictable on such relatively long time scales. Most theories of the MJ oscillation have been based on the wave instability theories, such as wave-CISK (conditional instability of second kind). As discussed by Hu and Stevens (HS), these theories have not yet satisfactorily explained the observations. Recently, HS have suggested that the MJ oscillation is actually a forced response to periodic heating. They suggest that the forced oscillations originates in the hydrologic cycle, without the active participation of large scale dynamics. According to their model, the oscillation originates in a progressive build up of atmospheric water vapor, which continues until a (prescribed) threshold is reached, after which precipitation begins and rapidly dries the atmosphere. The drying due to a precipitation episode is followed by renewed gradual moistening, and the cycle continues indefinitely in this way. Preliminary results are presented from a 1-D version of the Randall et al. GCM, which lends further support to the ideas of HS. The present 1-D results also differ in important ways from those of HS, however. In particular, cloud radiation effects are essential for the oscillatory behavior of the model, although they are not essential in the model of HS.

Randall, David A.↗
NASA NTRS1995

Neurodynamic oscillators

Oscillation of electrical activity has been found in many nervous systems, from invertebrates to vertebrates including man. There exists experimental evidence of very simple circuits with the capability of oscillation. Neurons with intrinsic oscillation have been found and also neural circuits where oscillation is a property of the network. These two types of oscillations coexist in many instances. It is nowadays hypothesized that behind synchronization and oscillation there is a system of coupled oscillators responsible for activities that range from locomotion and feature binding in vision to control of sleep and circadian rhythms. The huge knowledge that has been acquired on oscillators from the times of Lord Rayleigh has made the simulation of neural oscillators a very active endeavor. This has been enhanced with more recent physiological findings about small neural circuits by means of intracellular and extracellular recordings as well as imaging methods. The future of this interdisciplinary field looks very promising; some researchers are going into quantum mechanics with the idea of trying to provide a quantum description of the brain. In this work we describe some simulations using neuron models by means of which we form simple neural networks that have the capability of oscillation. We analyze the oscillatory activity with root locus method, cross-correlation histograms, and phase planes. In the more complicated neural network models there is the possibility of chaotic oscillatory activity and we study that by means of Lyapunov exponents. The companion paper shows an example of that kind.

Espinosa, Ismael↗