Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oriented”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Influence of Fiber Orientation on Deformation of Additive Manufactured Composites

Anisotropy caused by flow-induced fiber orientation of discontinuous fibers within the extrudate in the Extrusion Deposition Additive Manufacturing (EDAM) process gives rise to anisotropic shrinkage in printed parts and thereby, final part deformations. Three fiber orientation states, described by the second-order orientation tensor, were investigated to determine their influence upon final geometry. Two material systems were investigated including a short glass fiber-reinforced polyamide and a short carbon fiber-reinforced polyamide. A curvilinear geometry was modeled and printed virtually in the thermo-mechanical simulation, ADDITIVE3D©. The scale of the printed geometry was in the range of 300–400 mm and contained three semicircular geometry regions connected to linear regions, thereby inducing significant magnification of the spring-in deformation. The predicted deformation of the printed geometry for the three fiber orientation states and two material systems were compared. The deformation predicted for glass fiber-filled polyamide and carbon fiber-filled polyamide of the same fiber orientation states showed comparable deformations. In conclusion, the largest residual deformation was shown to correspond to the orientation tensor with the greatest degree of anisotropy.

36 MATERIALS SCIENCE↗

Growth and characterization of thin oriented Co{sub 3}O{sub 4} (111) films obtained by decomposition of layered cobaltates Na{sub x}CoO{sub 2}

The formation and structural characterization of highly (111)-oriented Co{sub 3}O{sub 4} films prepared by a novel procedure from weakly (001)-oriented Na{sub x}CoO{sub 2} is reported. The Na{sub x}CoO{sub 2} films were deposited on both single crystal and amorphous substrates by chemical solution deposition (CSD) method and crystallized at 700 °C. Subsequently they were transformed into (111)-oriented Co{sub 3}O{sub 4} phase during post-growth annealing at 900 °C. The degree of preferred orientation in Co{sub 3}O{sub 4}, which was determined by phi-scan and pole figure measurements, depends on the content of Na in the starting Na{sub x}CoO{sub 2} phase. Surface morphology of the films was investigated using electron microscopy and atomic force microscopy. - Graphical abstract: Structure of growth twins and possible O{sup 2−} stacking sequences in (111)-oriented Co{sub 3}O{sub 4} thin films on α-Al{sub 2}O{sub 3}(001) prepared by chemical solution deposition through the transformation of (001)-oriented Na{sub x}CoO{sub 2} thin film. - Highlights: • Single phase Co{sub 3}O{sub 4} thin films was prepared by means of chemical solution deposition. • Conditions for γ-Na{sub x}CoO{sub 2} to Co{sub 3}O{sub 4} transformation were optimized. • Growth twinning of Co{sub 3}O{sub 4} films due to two possible O{sup 2−} stacking sequences. • Growth with (pseudo)epitaxial relation Co{sub 3}O{sub 4} (111)[−121]//α-Al{sub 2}O{sub 3} (001)[10−10].

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of electrodeposition temperature on grain orientation and corrosion resistance of nanocrystalline pure nickel

The nanocrystalline pure nickels with different grain orientations were fabricated by direct current electrodeposition process. The grain size slightly decreased with the increasing of electrodeposition solution temperature. However, grain orientation was affected significantly. Comparing with samples obtained at 50 °C and 80 °C, sample obtained at 20 °C had the strongest (111) orientation plane which increased electrochemical corrosion resistance of this sample. At the same time, the lowest (111) orientation plane deteriorated electrochemical corrosion resistance of sample obtained at 50 °C. - Graphical abstract: The increased electrodeposition temperature promoted slightly grain refinement. The grain orientation was affected significantly by electrodeposition solution temperature. The (111) orientation plane of sample increased significantly corrosion resistance. Display Omitted.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Relationship between morphologies and orientations of Cu{sub 6}Sn{sub 5} grains in Sn3.0Ag0.5Cu solder joints on different Cu pads

The morphologies and orientations of Cu{sub 6}Sn{sub 5} intermetallic compounds in the Sn3.0Ag0.5Cu solder joints both on polycrystalline and single crystal Cu pads under different peak reflow temperatures and times above liquids were investigated. The relationship between Cu{sub 6}Sn{sub 5} grain orientations and morphologies was clarified. At the interface of Sn3.0Ag0.5Cu/polycrystalline Cu pad, scalloped Cu{sub 6}Sn{sub 5} intermetallic compounds formed at 250 °C and roof shape Cu{sub 6}Sn{sub 5} formed at 300 °C. Both scalloped Cu{sub 6}Sn{sub 5} and roof shape Cu{sub 6}Sn{sub 5} had a preferred orientation of (0001) plane being parallel to polycrystalline Cu pad surface. Besides, the percentage of large angle grain boundaries increased as the peak reflow temperature rose. At the interface of Sn3.0Ag0.5Cu/(111) single crystal Cu pad, the Cu{sub 6}Sn{sub 5} intermetallic compounds were mainly scallop-type at 250 °C and were prism type at 300 °C. The prismatic Cu{sub 6}Sn{sub 5} grains grew along the three preferred directions with the inter-angles of 60° on (111) single crystal Cu pad while along two perpendicular directions on (100) single crystal Cu pad. The orientation relationship between Cu{sub 6}Sn{sub 5} grains and the single crystal Cu pads was investigated by electron backscatter diffraction technology. In addition, two types of hollowed Cu{sub 6}Sn{sub 5} intermetallic compounds were found inside the joints of polycrystalline Cu pads. The long hexagonal Cu{sub 6}Sn{sub 5} strips were observed in the joints reflowing at 250 °C while the hollowed Cu{sub 6}Sn{sub 5} strips with the ‘▪’ shape cross-sections appeared at 300 °C, which was attributed to the different grain growth rates of different Cu{sub 6}Sn{sub 5} crystal faces. - Highlights: • The orientation of interfacial Cu{sub 6}Sn{sub 5} grains was obtained by EBSD technology. • Two types of hollowed Cu{sub 6}Sn{sub 5} strips were found at different temperatures. • The formation mechanism of hollowed Cu{sub 6}Sn{sub 5} was elaborated based on Bravais law. • The relationship between Cu{sub 6}Sn{sub 5} grain orientations and morphologies was clarified.

36 MATERIALS SCIENCE↗

Nano-scale orientation mapping of graphite in cast irons

A diametrical section of a graphite spheroid from a ductile iron sample was prepared using the focused ion beam-lift out technique. Characterization of this section was carried out through automated crystal orientation mapping in a transmission electron microscope. This new technique automatically collects electron diffraction patterns and matches them with precalculated templates. The results of this investigation are crystal orientation and phase maps of the specimen, which bring new light to the understanding of growth mechanisms of this peculiar graphite morphology. This article shows that mapping the orientation of carbon-based materials such as graphite, which is difficult to achieve with conventional techniques, can be performed automatically and at high spatial resolution using automated crystal orientation mapping in a transmission electron microscope. - Highlights: • ACOM/TEM can be used to study the crystal orientation of carbon-based materials. • A spheroid is formed by conical sectors radiating from a central nuclei. • Misorientations exist within the conical sectors, defining various orientation domains.

36 MATERIALS SCIENCE↗

Tutorial: Crystal orientations and EBSD — Or which way is up?

Electron backscatter diffraction (EBSD) is an automated technique that can measure the orientation of crystals in a sample very rapidly. There are many sophisticated software packages that present measured data. Unfortunately, due to crystal symmetry and differences in the set-up of microscope and EBSD software, there may be accuracy issues when linking the crystal orientation to a particular microstructural feature. In this paper we outline a series of conventions used to describe crystal orientations and coordinate systems. These conventions have been used to successfully demonstrate that a consistent frame of reference is used in the sample, unit cell, pole figure and diffraction pattern frames of reference. We establish a coordinate system rooted in measurement of the diffraction pattern and subsequently link this to all other coordinate systems. A fundamental outcome of this analysis is to note that the beamshift coordinate system needs to be precisely defined for consistent 3D microstructure analysis. This is supported through a series of case studies examining particular features of the microscope settings and/or unambiguous crystallographic features. These case studies can be generated easily in most laboratories and represent an opportunity to demonstrate confidence in use of recorded orientation data. Finally, we include a simple software tool, written in both MATLAB® and Python, which the reader can use to compare consistency with their own microscope set-up and which may act as a springboard for further offline analysis. - Highlights: • Presentation of conventions used to describe crystal orientations • Three case studies that outline how conventions are consistent • Demonstrates a pathway for calibration and validation of EBSD based orientation measurements • EBSD computer code supplied for validation by the reader.

36 MATERIALS SCIENCE↗

Study on a novel orientation domain of Mg17Ce2 in aged Mg–Y–Ce alloy by HAADF–STEM

Highlights: • A novel 90 degree orientation domain is verified in Mg{sub 17}Ce{sub 2} granules. • Orientations of domain–Ι and Π are parallel and perpendicular to α-Mg matrix. • A 〈 1-bar 010〉 direction is unchanged among domain–Ι, domain–Π and α-Mg matrix. • Domain–Ι matches the α-Mg matrix better than the domain–Π. - Abstract: After solid solution and aging treatment, Mg–3.0 wt%Y–1.0 wt%Ce ternary alloys were characterized using high angle annular dark field scanning transmission electron microscopy. The main precipitates are dominated by β{sup ′} phase and Mg{sub 17}Ce{sub 2}, a Ni{sub 17}Th{sub 2}–type intermetallic compound. An orientation domain can be discerned generally in Mg{sub 17}Ce{sub 2} granules. This domain structure of Mg{sub 17}Ce{sub 2} always consists of two types of domains (defined as domain–Ι and domain–Π) with a 90 degree orientation difference. In terms of crystallographic orientation relationships among α-Mg matrix and both domains, the domain–Ι is parallel to α-Mg matrix, whereas, the domain–Π is perpendicular to α-Mg matrix. It can be certain that a 〈 1-bar 010〉 direction is an unchanged orientation. Due to nearly equal values of lattice parameters (a and c) of Mg{sub 17}Ce{sub 2}, both domain–Ι and domain–Π can matches well with α-Mg matrix. Comparatively, the interfacial matching between domain–Ι and α-Mg matrix is better, suggesting that the domain–Ι is dominant.

36 MATERIALS SCIENCE↗

Fully implicit crystal plasticity models representing orientations with modified Rodrigues parameters

Here, this work describes a crystal plasticity formulation combining several mathematical, numerical, and implementation choices to produce a highly efficient model. Specifically, the key choices in the implementation are (1) representing orientations with modified Rodrigues parameters, (2) implementing a fully coupled implicit time integration for the elastic stretch, the crystal orientations, and the model internal variables, (3) implementing the model in the NEML2 constitutive modeling framework, based on PyTorch, to vectorize the calculations and port the computation to GPUs and other hardware accelerators, and (4) an exact implementation of the consistent tangent matrix, even for arbitrary coupling to other field variables beyond the displacements, like temperature, neutron fluence, etc. The first two features of the model are, to our knowledge, novel. The paper considers each of these choices individually as well as the final model as a whole. This includes a full description of modified Rodrigues parameters, their advantages over other representations of orientations, the mathematical formulae and tools required to implement a model with modified Rodrigues parameters, and a detailed description of the geometry of the space of modified Rodrigues parameters (in an appendix). It also includes a description of a fully implicit time integration scheme for the orientations and the advantages in representing orientations with modified Rodrigues parameters in implementing such a model. The work then assess, via numerical examples, the advantages of fully coupled implicit time integration versus more common decoupled and explicit time integration schemes. These studies demonstrate the computational advantages of fully coupled integration versus other time integration algorithms, though the performance of the competing models depends on the complexity of the underlying single crystal model. The study concludes by demonstrating that the choice of time integration method affects the sharpness of the predicted texture, with explicit methods for integrating the orientations overestimating texture sharpness and implicit methods underestimating texture sharpness.

Crystal plasticity↗

Characterizing Absolute Orientations in DNA Self-Assembly of Single Molecules

DNA self-assembly of single molecules (i.e., dyes) with deterministic orientations is a powerful approach for engineering mo-lecular excitons. However, current determination methods of the dye orientation relative to DNA do not account for the orien-tation of the dye plane, which is a missing degree of freedom needed to define absolute three-dimensional orientations. In this work, we combine fluorescence-detected linear dichroism, defocused dipole imaging, and DNA points accumulation for imaging in nanoscale topography (DNA-PAINT) super-resolution microscopy to determine the absolute three-dimensional orientations of single Cy5 dyes relative to host DNA duplexes which includes the dye plane orientation. The data revealed that the absorption and emission dipoles are perpendicular to the DNA duplex, and the mean dye plane is parallel to the DNA bases, which supports the notion that Cy5 dyes intercalate between DNA base pairs. The presented methodology will inspire the investigation of the dye plane orientation for controlling dye arrangement configurations beyond spontaneous π-stacking between dyes as well as achieving novel dye-DNA arrangements.

36 MATERIALS SCIENCE↗

Perfection in Nucleation and Growth of Blue-Phase Single Crystals: Small Free-Energy Required to Self-Assemble at Specific Lattice Orientation

Chemically patterned surfaces can be used to selectively stabilize blue phases as macroscopic single crystals with a prescribed lattice orientation. By tailoring the interfacial free energy through the pattern characteristics, it is possible to set, with nanoscale precision, the optimal conditions to induce spontaneously blue-phase crystal nucleation on the patterned substrate where a uniform, defect-free, blue-phase single crystal is finally formed in a matter of seconds. The chemical patterns taken into consideration in this work are made up of alternated stripelike regions of homeotropic and planar anchoring. By varying the stripe pattern dimension, including the period and ratio of the planar/homeotropic anchoring width, it is possible to generate blue-phase I single crystals with (110) lattice orientation and blue-phase II single crystals with either the (100), (110), or (111) lattice orientation. Continuum mean-field calculations of the studied systems serve to explain, in terms of the free energy of the systems, how the pattern dimensions favor certain crystallographic orientations while penalizing the others. We found that a small free-energy difference is sufficient to drive the nucleation and growth of blue phases into a certain lattice orientation. Furthermore, a processing window for obtaining arbitrary large blue-phase single crystals with predesigned lattice orientation, highly aligned reflective peaks, and significantly short forming time is provided here, which is essential for manufacturing and modulating optical devices and photonics.

36 MATERIALS SCIENCE↗

Probing the Orientation and Conformation of alpha-Helix and beta-Strand Model Peptides on Self-Assembled Monolayers Using Sum Frequency Generation and NEXAFS Spectroscopy

The structure and orientation of amphiphilic {alpha}-helix and {beta}-strand model peptide films on self-assembled monolayers (SAMs) have been studied with sum frequency generation (SFG) vibrational spectroscopy and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. The {alpha}-helix peptide is a 14-mer, and the {beta}-strand is a 15-mer of hydrophilic lysine and hydrophobic leucine residues with hydrophobic periodicities of 3.5 and 2, respectively. These periodicities result in the leucine side chains located on one side of the peptides and the lysine side chains on the other side. The SAMs were prepared from the assembly of either carboxylic acid- or methyl-terminated alkyl thiols onto gold surfaces. For SFG studies, the deuterated analog of the methyl SAM was used. SFG vibrational spectra in the C-H region of air-dried peptides films on both SAMs exhibit strong peaks near 2965, 2940, and 2875 cm{sup -1} related to ordered leucine side chains. The orientation of the leucine side chains was determined from the phase of these features relative to the nonresonant gold background. The relative phase for both the {alpha}-helix and {beta}-strand peptides showed that the leucine side chains were oriented away from the carboxylic acid SAM surface and oriented toward the methyl SAM surface. Amide I peaks observed near 1656 cm{sup -1} for the {alpha}-helix peptide confirm that the secondary structure is preserved on both SAMs. Strong linear dichroism related to the amide {pi}* orbital at 400.8 eV was observed in the nitrogen K-edge NEXAFS spectra for the adsorbed {beta}-strand peptides, suggesting that the peptide backbones are oriented parallel to the SAM surface with the side chains pointing toward or away from the interface. For the {alpha}-helix the dichroism of the amide {pi}* is significantly weaker, probably because of the broad distribution of amide bond orientations in the {alpha}-helix secondary structure.

36 MATERIALS SCIENCE↗

Controlling Domain Orientations in Thin Films of AB and ABA Block Copolymers

Domain orientations in thin films of lamellar copolymers are evaluated as a function of copolymer architecture, film thickness, and processing conditions. Two copolymer architectures are considered: An AB diblock of poly(styrene-b-methyl methacrylate) and an ABA triblock of poly(methyl methacrylate-b-styrene-b-methyl methacrylate). All films are cast on substrates that are energetically neutral with respect to the copolymer constituents. Film structures are evaluated with optical microscopy, atomic force microscopy, and grazing-incidence small-angle X-ray scattering. For AB diblock copolymers, the domain orientations are very sensitive to film thickness, annealing temperature, and imperfections in the 'neutral' substrate coating: Diblock domains are oriented perpendicular to the substrate when annealing temperature is elevated ({>=} 220 C) and defects in the substrate coating are minimized; otherwise, parallel or mixed parallel/perpendicular domain orientations are detected for most film thicknesses. For ABA triblock copolymers, the perpendicular domain orientation is stable for all the film thicknesses and processing conditions that were studied. The orientations of diblock and triblock copolymers are consistent with recent works that consider architectural effects when calculating the copolymer surface tension (Macromolecules 2006, 39, 9346 and Macromolecules 2010, 43, 1671). Significantly, the data demonstrate that triblocks are easier to process for applications in nanopatterning - in particular, when high-aspect-ratio nanostructures are required. However, both diblock and triblock films contain a high density of 'tilted' or bent domains, and these kinetically trapped defects should be minimized for most patterning applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Quantitatively identical orientation-dependent ionization energy and electron affinity of diindenoperylene

Molecular orientation dependences of the ionization energy (IE) and the electron affinity (EA) of diindenoperylene (DIP) films were studied by using ultraviolet photoemission spectroscopy and inverse photoemission spectroscopy. The molecular orientation was controlled by preparing the DIP films on graphite and SiO{sub 2} substrates. The threshold IE and EA of DIP thin films were determined to be 5.81 and 3.53 eV for the film of flat-lying DIP orientation, respectively, and 5.38 and 3.13 eV for the film of standing DIP orientation, respectively. The result indicates that the IE and EA for the flat-lying film are larger by 0.4 eV and the frontier orbital states shift away from the vacuum level compared to the standing film. This rigid energy shift is ascribed to a surface-electrostatic potential produced by the intramolecular polar bond (>C{sup −}-H{sup +}) for standing orientation and π-electron tailing to vacuum for flat-lying orientation.

74 ATOMIC AND MOLECULAR PHYSICS↗

Simple interpretation of nuclear orientation for Coulomb barrier distributions derived from a realistic effective interaction

A simple straightforward method has been presented to predict the dependence of barrier distributions at arbitrary orientations on different deformations. The proposed interpretation is developed independently of the complicated numerical calculations. It is related to the change of half-density radius of the deformed nucleus, in the direction of the separation vector. The microscopic calculations of Coulomb barrier are carried out by using a realistic density dependent nucleon-nucleon (NN) interaction, BDM3Y, for the interaction between spherical, {sup 48}Ca, and deformed, {sup 244}Pu, nuclei, as an example. To do so, the double-folding model for the interaction of spherical-deformed nuclei is put in a suitable computational form for the calculation of the potential at several separation distances and orientation angles using the density dependent NN force without consuming computational time. We found that the orientation distributions of the Coulomb barrier parameters show similar patterns to those of the interacting deformed nucleus radius. It is found that the orientation distribution of the Coulomb barrier radius follows the same variation of the deformed nucleus radius while the barrier height distribution follows it inversely. This correlation (anticorrelation) allows a simple evaluation of the orientation barrier distribution which would be very helpful to estimate when the barrier parameters will increase or decrease and at which orientations they will be independent of the deformation. This also allows us to estimate the compact and elongated configurations of the interacting nuclei which lead to hot and cold fusion, respectively.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Orientational analysis of atomic pair correlations in nanocrystalline indium oxide thin films

The application of grazing-incidence total X-ray scattering (GITXS) for pair distribution function (PDF) analysis using >50 keV X-rays from synchrotron light sources has created new opportunities for structural characterization of supported thin films with high resolution. Compared with grazing-incidence wide-angle X-ray scattering, which is only useful for highly ordered materials, GITXS/PDFs expand such analysis to largely disordered or nanostructured materials by examining the atomic pair correlations dependent on the direction relative to the surface of the supporting substrate. A characterization of nanocrystalline In 2 O 3 -derived thin films is presented here with in-plane-isotropic and out-of-plane-anisotropic orientational ordering of the atomic structure, each synthesized using different techniques. The atomic orientations of such films are known to vary based on the synthetic conditions. Here, an azimuthal orientational analysis of these films using GITXS with a single incident angle is shown to resolve the markedly different orientations of the atomic structures with respect to the planar support and the different degrees of long-range order, and hence, the terminal surface chemistries. It is anticipated that orientational analysis of GITXS/PDF data will offer opportunities to extend structural analyses of thin films by providing a means to qualitatively determine the major atomic orientation within nanocrystalline and, eventually, non-crystalline films.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multi-technique Characterization of Adsorbed Peptide and Protein Orientation: LK310 and Protein G B1

The ability to orient biologically active proteins on surfaces is a major challenge in the design, construction, and successful deployment of many medical technologies. As methods to orient biomolecules are developed, it is also essential to develop techniques that can accurately determine the orientation and structure of these materials. In this study, two model protein and peptide systems are presented to highlight the strengths of three surface analysis techniques for characterizing protein films: time-of-flight secondary-ion mass spectrometry (ToF-SIMS), sum-frequency generation (SFG) vibrational spectroscopy, and near-edge x-ray absorption fine structure (NEXAFS) spectroscopy. First, the orientation of Protein G B1, a rigid 6 kDa domain covalently attached to a maleimide-functionalized self-assembled monolayer, was examined using ToF-SIMS. Although the thickness of the Protein G layer was similar to the ToF-SIMS sampling depth, orientation of Protein G was successfully determined by analyzing the C{sub 2}H{sub 5}S{sup +} intensity, a secondary-ion derived from a methionine residue located at one end of the protein. Next, the secondary structure of a 13-mer leucine-lysine peptide (LK{sub 310}) adsorbed onto hydrophilic quartz and hydrophobic fluorocarbon surfaces was examined. SFG spectra indicated that the peptide's lysine side chains were ordered on the quartz surface, while the peptide's leucine side chains were ordered on the fluorocarbon surface. NEXAFS results provided complementary information about the structure of the LK{sub 310} film and the orientations of amide bonds within the LK{sub 310} peptide.

59 BASIC BIOLOGICAL SCIENCES↗

Characterization of Nanoclay Orientation in Polymer Nanocomposite Film by Small-angle X-ray Scattering

The orientation distribution of layer-shaped nanoclays (e.g. organoclays and pristine clays) dispersed in a polymer matrix is an important parameter to control the properties of polymer nanocomposites. In this study, we demonstrate that the use of multi-directional 2-D small-angleX-rayscattering (SAXS) can quantitatively describe the orientation distribution of organoclays (e.g. Cloisite C20A) in melt-pressed nanocompositefilms, containing ethylene-vinyl acetate (EVA) copolymers as polymer matrices. Different weight fractions of organoclays were used to alter the orientation profile of nanocompositefilms, in which the dispersion and morphology of organoclays were also characterized by complementary 2-D and 3-D transmission electron microscopy (TEM). All nanocomposites exhibited mixed intercalation/exfoliation clay morphology, where the intercalated structure possessed partial orientation parallel to the in-plane direction of the film. The higher content of the clay loading showed a higher clay orientation. A simple analytical scheme for SAXS data analysis to determine the orientation parameter (P{sub 2}) was demonstrated, the results of which are in agreement with the gas permeation properties of the nanocompositefilms.

36 MATERIALS SCIENCE↗

Synthesis and Characterization of Self-assembled c-axis Oriented Bi2Sr3Co2Oy Thin Films by the Sol gel Method

Bi{sub 2}Sr{sub 3}Co{sub 2}Oy thin films are prepared on SrTiO{sub 3} (100), (110) and (111) single crystal substrates using the sol-gel method. All the thin films are c-axis oriented regardless of the orientation of the substrate suggesting self-assembled c-axis orientation, and X-ray photoelectron spectroscopy results give evidence of coexistence of Co{sup 3+} and Co{sup 2+} ions in the derived films. Transmission electronic microscopy observations reveal that all samples are c-axis oriented with no obvious differences for different samples, and the c-axis lattice constant is determined as 15 {angstrom} suggesting the misfit structure. A phenomenological thermodynamic phase diagram for self-assembled c-axis orientation is established for misfit cobaltate-based films using chemical solution deposition. All samples behave like semiconductors due to the coexistence of Co{sup 3+}/Co{sup 2+} ions, and the resistivity at 350 K is 47, 39 and 17 m{Omega} cm for the thin films on SrTiO{sub 3} (100), (110) and (111), respectively, whereas the Seebeck coefficient at 300 K is 97, 89 and 77 {micro}V K{sup -1}. The successful attainment of Bi{sub 2}Sr{sub 3}Co{sub 2}O{sub y} thin films with self-assembled c-axis orientation will provide an effective prototype for investigation of growth mechanisms in complex oxide thin films with a misfit structure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗