Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “optical pumping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Final amplifier of an ultra-intense all-OPCPA system with 13-J output signal energy and 41% pump-to-signal conversion efficiency

Optical parametric chirped-pulse amplification (OPCPA) using high-energy Nd:glass lasers has the potential to produce ultra-intense pulses (>10 23 W/cm 2 ). We report on the performance of the final high-efficiency amplifier in an OPCPA system based on large-aperture (63 × 63-mm 2 ) partially deuterated potassium dihydrogen phosphate (DKDP) crystals. The seed beam (180-nm bandwidth, 110 mJ) was provided by the preceding OPCPA stages. A maximum pump-to-signal conversion efficiency of 41% and signal energy up to 13 J were achieved with a 52-mm-long DKDP crystal due to the flattop super-Gaussian pump beam profile and flat-in-time pulse shape.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Time-resolved magneto-optical effects in the altermagnet candidate MnTe

α -MnTe is an antiferromagnetic semiconductor with above room temperature T N = 310 K, which is promising for spintronic applications. Recently, it was reported to be an altermagnet, containing bands with momentum-dependent spin splitting; time-resolved experimental probes of MnTe are, therefore, important both for understanding novel magnetic properties and potential device applications. Here, we investigate ultrafast spin dynamics in epitaxial MnTe(001)/InP(111) thin films using pump-probe magneto-optical measurements in the Kerr configuration. At room temperature, we observe an oscillation mode at 55 GHz that does not appear at zero magnetic field. Combining field and polarization dependence, we identify this mode as a magnon, likely originating from inverse stimulated Raman scattering. Magnetic field-dependent oscillations persist up to at least 335 K, which could reflect coupling to known short-range magnetic order in MnTe above T N . Additionally, we observe two optical phonons at 3.6 and 4.2 THz, which broaden and redshift with increasing temperature.

Gray, Isaiah↗
DOE OSTI2022

Gain roll-off in cadmium selenide colloidal quantum wells under intense optical excitation

Colloidal quantum wells, or nanoplatelets, show among the lowest thresholds for amplified spontaneous emission and lasing among solution-cast materials and among the highest modal gains of any known materials. Using solution measurements of colloidal quantum wells, this work shows that under photoexcitation, optical gain increases with pump fluence before rolling off due to broad photoinduced absorption at energies lower than the band gap. Despite the common occurrence of gain induced by an electron–hole plasma found in bulk materials and epitaxial quantum wells, under no measurement conditions was the excitonic absorption of the colloidal quantum wells extinguished and gain arising from a plasma observed. Instead, like gain, excitonic absorption reaches a minimum intensity near a photoinduced carrier sheet density of 2 × 10 13 cm –2 above which the absorption peak begins to recover. To understand the origins of these saturation and reversal effects, measurements were performed with different excitation energies, which deposit differing amounts of excess energy above the band gap. Across many samples, it was consistently observed that less energetic excitation results in stronger excitonic bleaching and gain for a given carrier density. Transient and static optical measurements at elevated temperatures, as well as transient X-ray diffraction of the samples, suggest that the origin of gain saturation and reversal is a heating and disordering of the colloidal quantum wells which produces sub-gap photoinduced absorption.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Organic Cation Influence on Organic–Inorganic Thermal Equilibration within 2D Metal Halide Perovskites

Two-dimensional inorganic–organic lead halide perovskites exhibit tunable optoelectronic properties that are dictated by alternating layers of metal halide octahedra and organic cations. In such hybrid materials, vibrational coupling and thermalization between the low mass, insulating, organic cation spacers, and high mass inorganic octahedra remains poorly understood. Here, in this study, using femtosecond infrared-pump electronic-probe (IPEP) spectroscopy, we investigate the role of organic cation identity regarding the kinetics of vibrational energy exchange and sublattice mechanical coupling. Linear aliphatic cation-containing 2D perovskites with 4, 6, or 8 carbons (butylammonium = BA, hexylammonium = HA, and octylammonium = OA) were produced as thin films and mid-infrared pump pulses and then selectively excited organic cation stretch vibrations. Thermal energy introduction was evaluated via visible-wavelength optical probing that conveys inorganic octahedra response, owing to changes in electronic absorption. Multiple distinct spectral shifts appear upon excitation of the organic cations. Following an initial optical Stark shift caused by pump–probe temporal overlap, a redshift occurs within the first 10 ps that we attribute to compression of the octahedra by the expanded organic layers. Subsequently, a blueshift of the bandgap occurs commensurate with equilibration of both sublattices at an elevated temperature with a time constant of 21.8 to 31.6 ps depending on the spacer identity, with thermal energy transfer slowing by nearly 50% for the longest linker. By examining the effect that altered cation identity has on vibrational energy exchange, this work begins to offer routes to tune nonequilibrium response as well as provides insight into the fundamental impacts of organic spacers on thermal energy exchange in perovskite materials.

Peifer, Shoshanna E. [Northwestern Univ., Evanston↗
DOE OSTI2025

Full complex amplitude control of second-harmonic generation via electrically tunable intersubband polaritonic metasurfaces

Nonlinear intersubband polaritonic metasurfaces based on coupling of the intersubband nonlinear optical response of quantum-engineered semiconductor heterostructures and electromagnetic modes of nanoresonators provide efficient frequency mixing with moderate pump intensities. The resonant nonlinear optical response, represented as a complex function, can be modulated via Stark tuning of intersubband transition energies under applied voltages. However, achieving full complex amplitude control (both phase and magnitude) remains challenging. In this work, we present and experimentally validate electrically tunable nonlinear intersubband polaritonic metasurfaces that achieve complete complex amplitude control for second-harmonic generation (SHG). Through a design featuring two in-plane flipped meta-atoms per unit cell, we achieve complete electrical control of both the amplitude and phase of the metasurface second-order nonlinear susceptibility, with a tuning range of 0 to 30 nm V −1 for the magnitude and 0-2π for the phase of the nonlinear optical response. Using these properties, we achieve complete on-off SHG modulation and beam diffraction tuning through electrically controlled amplitude and phase gratings.

Science & Technology - Other Topics↗
DOE OSTI2021

2D monochromatic x-ray imaging for beam monitoring of an x-ray free electron laser and a high-power femtosecond laser

Single-shot simultaneous beam monitoring of an x-ray free electron laser (XFEL) and a high-power femtosecond laser is demonstrated using 2D monochromatic Kα imaging. In a pump-probe experiment carried out at the Matter in Extreme Conditions end-station of the Linac Coherent Light Source, a thin solid titanium foil irradiated by a 25-TW relativistic intensity laser for fast electron isochoric heating was probed by a 7.0 keV XFEL beam for x-ray Thomson scattering measurements. Using a spherical crystal imager (SCI), the spatial overlap of the beams was examined by measuring 4.5 keV titanium Kα x rays produced by laseraccelerated fast electrons and the x-ray beam. Changes in XFEL-induced Kα emission patterns were observed down to a ~20×40 μm2 rectangular shape as the beam was focused. Laser-only and two-beam shots reveal that large spatial offsets of laser-induced Kα spots in a horizontal direction is attributed to imprecise target positioning rather than shot-to-shot laser pointing variations. As a consequence, successful beam overlapping was observed on ~58% of all two-beam shots for 10 μm thick samples. The Kα measurements also show a linear relationship between total Kα yields and integrated x-ray scattering signals. Monochromatic xray imaging with SCI could be used as an on-shot beam pointing diagnostic in XFEL-laser or multiple short-pulse laser experiments.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Exploring the relationship between deposition method, microstructure, and performance of Nb/Si-based superconducting coplanar waveguide resonators

Superconducting quantum circuits (SQC) are one of the most promising hardware platforms for quantum computing, yet their performance is currently limited by the presence of various structural defects inside the circuit's structure. Despite impressive progress in the past decade, a precise understanding of the origin of these defects from various fabrication processes and their impact on coherence is still lacking. Here, in this study, we performed a comprehensive investigation on the microstructure, superconductivity, and resonator quality factor of Nb films deposited by high-power impulse magnetron sputtering (HiPIMS) and direct current (DC) magnetron sputtering. A suite of characterization techniques, including electron microscopy with spectroscopy, secondary ion mass spectrometry, magneto-optical microscopy, and pump-probe reflectivity spectroscopy is used. We reveal that niobium (Nb) resonators fabricated using HiPIMS exhibit a smaller average grain size, thicker surface oxide with larger thickness variations (rougher surface), and a thicker amorphous Nb/Si interface layer compared to samples deposited by DC sputtering. We identified that the amorphous Nb oxides (mainly located at the Nb surface and along the grain boundaries) and Nb-Si amorphous layers (at the Nb/Si interface) are major and potential sources of two-level system (TLS), while off-stochiometric oxides and suboxides of Nb close to the surface, crystalline defects (i.e., dislocations at grain boundary, point defects introduced during deposition) are main contributors of non-TLS sources. Our findings clarify the relationship between different defects and coherence loss mechanisms, highlighting the importance of material microstructure control on performance optimization in SQC.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Spatio-Kinetic Electronic Heterogeneity in MoS 2 Revealed by Ultrafast Electron Microscopy: Implications for Optoelectronics

There is broad interest in layered, two-dimensional (2D) semiconductors owing to their high optical absorption and ability to heterogeneously integrate with various substrates. In such layered semiconductors, mesoscopic imperfections, such as surface step edges, may affect charge carrier kinetics and device performance, but studying their effects on carrier transport with sufficient spatial and temporal resolution is a challenge. Using scanning ultrafast electron microscopy, we image the near-surface charge carrier kinetics with μm/ps spatiotemporal resolution in single-crystal MoS 2 samples with surface steps tens of nanometers in height. We find an approximately 3-fold increase in surface trap density near such surface steps compared to the uniform, flat surface regions. Despite the difference in trap state density, filling of the traps occurs over the same time scale (∼100 ps), but carrier recovery is much slower near the step compared to the uniform regions of the material. Furthermore, these results provide an approach to measure ultrafast dynamics and determine the required uniformity of layered materials depending on the speed limit constraints for specific applications.

SEM↗
DOE OSTI2022

Quantum Shells Boost the Optical Gain of Lasing Media

Auger decay of multiple excitons represents one of the main obstacles to photonic applications of semiconductor quantum dots (QDs). These non-radiative processes are particularly detrimental to the performance of QD-based electroluminescent and lasing devices. Here, we demonstrate that by using semiconductor quantum shells with an “inverted” QD geometry, it is possible to inhibit Auger recombination, allowing extraordinary improvements to their multi-exciton characteristics. Additionally, we show that quantum shells result in ultralong biexciton lifetimes (>10 ns), and an associated biexciton quantum yield of up to 81%. Furthermore, the energy-dispersive architecture of quantum shells leads to exciton-exciton repulsion, which splits the single-exciton and bi-exciton optical transitions. In this regime, quantum shells produce the longest optical gain lifetime reported for colloidal QDs to date (> 6 ns) over a broad amplification bandwidth. Therefore, the employment of quantum shells in optically- or electrically-pumped gain media can lead to a substantial improvement in device performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Anisotropic ultrafast spin dynamics in epitaxial cobalt

We investigate the ultrafast spin dynamics in an epitaxial hcp($1\bar100$) cobalt thin film. By performing pump–probe magneto-optical measurements with the magnetization along either the easy or hard magnetic axis, we determine the demagnetization and recovery time for the two axes. We observe an average of 33% slower dynamics along the easy magnetization axis, which we attribute to magneto-crystalline anisotropy of the electron–phonon coupling, supported by our ab initio calculations. This points toward an unambiguous and previously undisclosed role of anisotropic electron–lattice coupling in ultrafast magnetism.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

3D velocity map imaging of electrons with TPX3CAM

In this report we demonstrate three-dimensional velocity map imaging of low energy electrons using a TPX3CAM, where the three-dimensional momentum information [$p_x, p_y, p_z$] is encoded in position and timing [x, y, t] of hits on the camera sensor. We make use of the camera sensor for the [x, y] information and a constant fraction discriminator and fast time to digital converter in the camera for the time information. We illustrate the capabilities of our apparatus by presenting above threshold ionization measurements of xenon, which produces well defined structures in the momentum resolved photoelectron yield.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Optically Induced Anisotropy in Time-Resolved Scattering: Imaging Molecular-Scale Structure and Dynamics in Disordered Media with Experiment and Theory

Time-resolved scattering experiments enable imaging of materials at the molecular scale with femtosecond time resolution. However, in disordered media they provide access to just one radial dimension thus limiting the study of orientational structure and dynamics. Here we introduce a rigorous and practical theoretical framework for predicting and interpreting experiments combining optically induced anisotropy and time-resolved scattering. Using impulsive nuclear Raman and ultrafast x-ray scattering experiments of chloroform and simulations, we demonstrate that this framework can accurately predict and elucidate both the spatial and temporal features of these experiments.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

High-efficiency narrow-bandwidth KTP optical parametric oscillator for kHz–MHz planar laser-induced fluorescence

The electronic excitation of key combustion species or flow tagging of chemical species requires a narrowband tunable UV source. In this work, a potassium titanyl phosphate (KTP) burst-mode optical parametric oscillator (OPO) pumped by a 532 nm laser is developed to generate a spectrally narrow signal and an idler output with 1.48 ± 0.19 cm −1 bandwidth without the need for injection seeding. The idler (1410–1550 nm range) is further mixed with 355 or 266 nm to generate 284 or 226 nm for OH or NO planar laser-induced fluorescence (PLIF), respectively, with up to 1.9% conversion efficiency from 1064 nm to the UV. MHz-rate burst profiles are reported, and OH and NO PLIF are demonstrated in a rotating detonation combustor at rates up to 200 kHz.

Webb, Austin M. (ORCID:0000000155897474)↗
DOE OSTI2021

Thermal Infrared Detectors: expanding performance limits using ultrafast electron microscopy

This project aimed to identify the performance-limiting mechanisms in mid- to far infrared (IR) sensors by probing photogenerated free carrier dynamics in model detector materials using scanning ultrafast electron microscopy (SUEM). SUEM is a recently developed method based on using ultrafast electron pulses in combination with optical excitations in a pump- probe configuration to examine charge dynamics with high spatial and temporal resolution and without the need for microfabrication. Five material systems were examined using SUEM in this project: polycrystalline lead zirconium titanate (a pyroelectric), polycrystalline vanadium dioxide (a bolometric material), GaAs (near IR), InAs (mid IR), and Si/SiO 2 system as a prototypical system for interface charge dynamics. The report provides detailed results for the Si/SiO 2 and the lead zirconium titanate systems.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Time-resolved probing of laser-induced nanostructuring processes in liquids

Laser synthesis and processing of colloids (LSPC) in liquids has gained widespread applications in producing nanomaterials of different classes of solids. While the technical processes in different cases of ablation, fragmentation or colloidal fusion may look macroscopically different in each application, the underlying fundamental mechanisms are always the same cascade of laser interaction with matter, non-thermal or thermal energy deposition, phase transitions, and the subsequent structure formation processes. Disentangling these mechanisms represents a veritable challenge, as ultrafast and structurally sensitive experimental methods are required. This review presents a discussion of how state-of-the-art experimental protocols using ultrafast lasers and sensitive structural probes, such as electrons or X-rays are able to address this challenge. In particular, it is possible to investigate LSPC on single objects using single probe pulses and avoid accumulation effects in a heterogeneous sample. The presented results capture structure formation with femtosecond and atomic scale resolution. Ultrafast time-resolved probing approaches are key to revealing the transient states and pathways that govern material transformation in LSPC.

X-ray scattering↗
DOE OSTI2024

Truncated nonlinear interferometer-based sensor system

A truncated non-linear interferometer-based sensor system includes an input port that receives an optical beam and a non-linear amplifier that amplifies the optical beam with a pump beam and renders a probe beam and a conjugate beam. The system's local oscillators have a relationship with the respective beams. The system includes a sensor that transduces an input with the probe beam and the conjugate beam or their respective local oscillators. It includes one or more phase-sensitive detectors that detect a phase modulation between the respective local oscillators and the probe beam and the conjugate beam. Output from the phase-sensitive-detectors is based on the detected phase modulation. The phase-sensor-detectors include measurement circuitry that measure the phase signals. The measurement is the sum or difference of the phase signals in which the measured combination exhibit a quantum noise reduction in an intensity difference or a phase sum or an amplitude difference quadrature.

Pooser, Raphael C.↗
DOE OSTI2020

Nonlinear interferometer systems and methods

Nonlinear interferometers include a nonlinear optical medium that is situated to produce a conjugate optical beam in response to a pump beam and a probe beam. The pump, probe, and conjugate beams propagate displaced from each other along a common optical path. One of the beams is selectively phase shifted, and the beams are then returned to the nonlinear medium, with the selectively phase shift beam phase shifted again. The nonlinear medium provides phase sensitive gain to at least one of the probe or conjugate beams, and the amplified beam is detected to provide an estimate of the phase shift.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Anomalous ultrafast all-optical Hall effect in gapped graphene

We propose an ultrafast all-optical anomalous Hall effect in two-dimensional (2D) semiconductors of hexagonal symmetry such as gapped graphene (GG), transition metal dichalcogenides (TMDCs), and hexagonal boron nitride (h-BN). To induce such an effect, the material is subjected to a sequence of two strong-field single-optical-cycle pulses: A chiral pump pulse followed within a few femtoseconds by a probe pulse linearly polarized in the armchair direction of the 2D lattice. Due to the effect of topological resonance, the first (pump) pulse induces a large chirality (valley polarization) in the system, while the second pulse generates a femtosecond pulse of the anomalous Hall current. The proposed effect is fundamentally the fastest all-optical anomalous Hall effect possible in nature. It can be applied to ultrafast all-optical storage and processing of information, both classical and quantum.

36 MATERIALS SCIENCE↗