Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “miller cycle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Facile Synthesis of Boron-Doped rGO as Cathode Material for High Energy Li–O 2 Batteries

To improve the electrochemical performance of the high energy Li–O2 batteries, it is important to design and construct a suitable and effective oxygen-breathing cathode. Herein, a three-dimensional (3D) porous boron-doped reduction graphite oxide (B-rGO) material with a hierarchical structure has been prepared by a facile freeze-drying method. In this design, boric acid as the boron source helps to form the 3D porous structure, owing to its cross-linking and pore-forming function. This architecture facilitates the rapid oxygen diffusion and electrolyte penetration in the electrode. Meanwhile, the boron–oxygen functional groups linking to the carbon surface or edge serve as additional reaction sites to activate the ORR process. It is vital that boron atoms have been doped into the carbon lattices to greatly activate the electrons in the carbon π system, which is beneficial for fast charge under large current densities. Density functional theory calculation demonstrates that B-rGO exhibits much stronger interactions with Li5O6 clusters, so that B-rGO more effectively activates Li–O bonds to decompose Li2O2 during charge than rGO does. With B-rGO as a catalytic substrate, the Li–O2 battery achieves a high discharge capacity and excellent rate capability. Moreover, catalysts could be added into the B-rGO substrate to further lower the overpotential and enhance the cycling performance in future.

Wu, Feng↗

Using the Time-Correlated Induced Fission Method to Simultaneously Measure the 235 U Content and the Burnable Poison Content in LWR Fuel Assemblies

The uranium neutron coincidence collar uses thermal neutron interrogation to verify the 235 U mass in low-enriched uranium (LEU) fuel assemblies in fuel fabrication facilities. Burnable poisons are commonly added to nuclear fuel to increase the lifetime of the fuel. The high thermal neutron absorption by these poisons reduces the active neutron signal produced by the fuel. Burnable poison correction factors or fast-mode runs with Cd liners can help compensate for this effect, but the correction factors rely on operator declarations of burnable poison content, and fast-mode runs are time-consuming. Finally, this paper describes a new analysis method to measure the 235 U mass and burnable poison content in LEU nuclear fuel simultaneously in a timely manner, without requiring additional hardware.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

TEM-based phase characterization of $\mathrm{U–19Pu–10Zr}$ irradiated in ATR

We report the results of the microstructural examination of the irradiated U–19Pu–10Zr fuel. New insights gained using selective area electron diffraction analysis in a transmission electron microscope provide crystallographic information on the phases previously identified based primarily on the chemical compositions. After irradiation, the microstructure of the fuel separates into γ-(U, Pu, Zr) in the central region with a secondary nanocrystalline UO 2 phase, γ-(U, Pu, Zr) with a secondary ZrO 2 phase in the intermediate, and ζ-(U, Pu) in the outer regions. While the surface microstructural features and porosity indicate separation into three concentric zones consistent with the existing constituent redistribution model, crystallographically the fuel consists of two zones: inner (with γ-(U, Pu, Zr) as a matrix phase) and outer (with ζ-(U, Pu) as a matrix phase). Our results highlight the importance of crystal structure in phase identification and can be used to supplement the existing constituent redistribution model.

extreme environment↗

Microstructural Examinations of Reactor Pressure Vessel Surveillance and Test Reactor Irradiated Materials

The reactor pressure vessel (RPV) in a light-water reactor (LWR) represents the first line of defense against a release of radiation in case of an accident. Thus, regulations that govern the operation of commercial nuclear power plants require conservative margins of fracture toughness, both during normal operation and under accident scenarios. In the unirradiated condition, the RPV has sufficient fracture toughness such that failure is implausible under any postulated condition, including pressurized thermal shock (PTS) in pressurized water reactors (PWR). In the irradiated condition, however, the fracture toughness of the RPV may be severely degraded, with the degree of toughness loss dependent on the radiation sensitivity of the materials. As stated in previous progress reports, the available embrittlement predictive models, e.g. [1], and our present understanding of radiation damage are not fully quantitative, and do not treat all potentially significant variables and issues, particularly considering extension of operation to 80y. The major issues regarding irradiation effects are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NEAMS Workbench and Bison Fuel Performance Remote Application Configuration

The mission of the US Department of Energy (DOE) Nuclear Energy Advanced Modeling and Simulation (NEAMS) Program is to develop, apply, deploy, and support state-of-the-art predictive modeling and simulation tools for the design and analysis of current and future nuclear energy systems. This is accomplished using computing architectures that range from laptops to leadership class facilities. The NEAMS Workbench [1,2,3] initiative will facilitate the transition from conventional computer codes to high-fidelity ones by providing a common analysis environment and interface for model creation, review, execution, output review, and visualization for integrated codes. The BISON fuel performance code [4] is a finite element method (FEM)-based software being developed by multiple organizations led by the Idaho National Laboratory for the US Department of Energy Office of Nuclear Energy. BISON can simulate a variety of fuel and cladding compositions and geometries in varying dimensionalities, depending upon the problem type and complexity, including one-dimensional (1D), 1.5D, 2D axially symmetric (2D-rz), 2D radial-azimuthal (2D-rθ), or 3D models. The NEAMS Workbench allows execution of the BISON fuel performance code on local and remote compute resources. In this report, the detailed instructions of configuring the NEAMS Workbench for remote execution of the BISON fuel performance code on a portable batch system (PBS)-scheduled compute resource, as well the transfer of associated Bison files, is illustrated.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Autoradiography Using OSL for Monitoring Warhead Dismantlement

The use of radiation imaging techniques to provide increased confidence in a dismantlement verification regime is still under investigation. Currently, radiation measurements can be used to confirm attributes such as the presence, quality, and mass of containerized nuclear material. However, imaging techniques can be used to confirm the shape, size, and/or symmetry of the object being interrogated. Imaging can be used as a complementary technique to radiation measurements to confirm a declaration or as a chain of custody measure to confirm that an item has not been tampered with. As with other attribute measurements, the image data must be protected behind an information barrier and analyzed to give an unclassified result when compared to an agreed upon threshold. This paper will discuss the use of Optically Stimulated Luminescence to perform autoradiography of sources using coded apertures to differentiate between point sources and various distributed sources. The coded aperture chosen for this application is based on modified uniform redundant arrays (mURAs) which resulted in the design and manufacture of an efficient, high-resolution mURA mask/antimask system. The potential use of the autoradiography technique with the coded aperture as an intrinsic information barrier and the required protection of the mask and unfolding algorithm will also be discussed. This project has been supported by the US Department of Energy’s National Nuclear Security Administration’s Office of Dismantlement and Transparency (DOE/NNSA/NA-241).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural Characterization of Burnable Absorber Materials Being Evaluated for Application in LEU U-Mo Fuel Plates

The starting microstructure of a fuel plate will impact how it performs during irradiation. As a result, microstructural characterization has been performed on as-fabricated monolithic fuel plates to determine the changes in fuel plate microstructure that may result from changes in fabrication parameters. Particular focus has been given to the fuel plate U-10Mo/Zr and Zr/AA6061 cladding interfaces, since the integrity of these interfaces will play a big role in determining the overall performance of the fuel plate during irradiation. In addition, burnable absorber materials for potential incorporation into monolithic fuel plates have been characterized to identify their as-fabricated microstructures. This information will be important when trying to understand the PIE data from fuel plates with burnable absorbers that are irradiated in future irradiation experiments. This paper will focus on the microstructures observed using optical metallography, X-ray diffraction, and scanning and transmission electron microscopy for monolithic fuel plates exposed to different fabrication parameters and for as-fabricated burnable absorber materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

U-10Mo Monolithic Fuel Qualification Plan

The Material Management and Minimization (M3) Program’s primary objective within the U.S. Department of Energy/National Nuclear Security Administration is to achieve permanent threat reduction by minimizing and when possible, eliminating weapon-usable nuclear material around the world. Under M3’s Office of Conversion, the U.S. High Performance Research Reactor (USHPRR) Project, is pursuing a fuel qualification and licensing effort focused on converting high-performance research reactors in the United States from using highly enriched uranium (HEU) fuel to using low-enriched uranium (LEU) fuel. The body of this document is focused on defining the activities required for generic qualification of high density, LEU fuel that then allows reactor conversions to proceed for the four high-performance research reactors and the critical assembly that will operate using the U-10Mo monolithic fuel design (see Subsection 1.3): MITR, MURR, NBSR, ATR, and ATRC. Fuel qualification in this report means generic fuel acceptance of the U-10Mo monolithic fuel form by the NRC for use in reactor conversions in the United States, which allows the fuel to be used in subsequent reactor specific licensing requests. The U 10Mo Monolithic Fuel Research, Development, and Qualification Plan utilizes the functions and requirements of the USHPRR Project that was established in the Functions and Requirements Document (F&RD) [1] and expands on these requirements to ensure that planned tests have traceable results that will ensure the requirement has been met. The methods by which data will be collected to show that these requirements have been met are described in this document.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A perspective on the interaction between the NCSD and ANSI/ANS-8 standards

The intent of this paper is to illuminate the reasons behind the culture of standards involvement by the criticality safety community in the NCSD (Nuclear Criticality Safety Division), and specifically highlight those NCSD activities that build/support this culture. Many NCSD members are currently active in ANSI/ANS-8 and other standards and have been for the last half century. This paper was inspired by a request from ANS's Professional Divisions Committee concerning how the professional divisions could 'increase support to Standards development as Subject Matter Experts'. The healthy level of involvement (i.e., culture) by the NCSD membership in standards was noted. A history of the ANSI/ANS-8 series standards is provided, with roots going back to 1955. The need became apparent during a cluster of nuclear criticality accidents that occurred between 1958-1962. The first NCS related standard was the American Standard N6.1-1964, the parent of ANSI/ANS-8.1, which was prepared in 1958 and adopted in 1964. Thus, the involvement in standards by the NCS community goes back more than 50 years. The NCSD continues to help foster a culture of standards use and development. However, the support provided by the NCSD is frequently not recognized, and standards activities are often viewed as separate from the NCSD. This paper highlights the interaction between the NCSD and the ANSI/ANS-8 standards activities as well as the benefit of this support. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The Impact of Furnace-Testing on the Microstructure of an Irradiated U-Mo Fuel Plate

The Material Management and Minimization Program (formerly known as the Reduced Enrichment for Research and Test Reactor Program) is responsible for converting research reactors that use highly enriched uranium (HEU) fuels to ones that use low-enriched uranium (LEU) fuels. As part of the development of LEU fuels, a variety of irradiation experiments are being conducted using the Advanced Test Reactor. In addition to the reactor tests, there is interest in generating information about the transient behavior of irradiated fuel plates. For example, it is of interest to determine the temperature at which a blister will form on the surface of a fuel plate, due to fission gas release from the fuel meat, for a particular fuel plate design. Since in-pile testing to determine the 'blister threshold' (the temperature where a blister forms on the surface of a fuel plate) in plate-type fuel is very difficult and expensive and has historically been deemed impractical for fuel qualification testing, an out-of-pile 'blister test' has been developed and employed. This post-irradiation blister anneal test was developed as a conservative simulation of in-pile behavior and has been routinely used for many research reactor fuel designs currently in use. In this test, the irradiated fuel plate is inserted into a furnace at a given temperature, soaked for a period of time, and removed for inspection. If no visible blisters appear, the furnace temperature is increased, and the plate is soaked and inspected again. This process continues until blisters are observed. Recently, a section from an irradiated U-7Mo dispersion fuel plate with Al-4043 matrix, which has a nominal composition of 4.81Si-0.20Fe-0.14Ti-0.16Cu-0.01Cr 0.01Mn-bal Al, was tested in a furnace located in the Hot Fuel Examination Facility, located at the Idaho National Laboratory, up to 500 deg. C, at which point blisters were observed on the surface of the fuel plate section. A sample near the blistered region of the fuel plate section was then characterized using scanning electron (SEM) and transmission electron microscopy (TEM). This paper discusses the results of this characterization and how they compare to those generated for a similar sample characterized after fabrication but before irradiation and for a sample characterized after irradiation but before furnace testing. One goal of this work is to identify the changes in the microstructure during blister testing that contribute to the eventual release of fission gas that results in the development of blisters. SEM analysis of the furnace-tested sample showed that in some locations of the U-7Mo particles, Al-4043 matrix constituents (primarily Si) had penetrated the microstructure along grain boundaries. This provided potential pathways for increased fission gas migration in the fuel meat microstructure during the furnace heating process. Some attack of these boundaries was also observed in the as-fabricated U-7Mo/Al-4043 sample, but there appeared to be additional attack during the furnace annealing. Besides the changes observed in grain boundary features, the TEM analysis showed that the fission gas bubbles that are typically present in the intra-granular regions of the as-irradiated U-7Mo microstructure as a fission gas bubble superlattice had changed in size, morphology, and distribution. The result of this may be an increase in the mobility of the fission gas in intra-granular regions of the fuel. The complete implications of the changes in fission gas morphology and distribution in the fuel meat microstructure and their impact on blistering continues to be investigated. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Radiation Effect on Microstructural Stability of RERTR Fuel

Three depleted uranium alloys are successfully cast for the radiation stability studies of the fuel-cladding interaction product using proton irradiation. SEM analysis indicates the presence of the phases of interest: U(Si,Al)3, (U,Mo)(Si,Al)3 and a mixture of UMo2Al20, U6Mo4Al43, and UAl4. Irradiation with 2.6 MeV protons at 200ºC to the doses of 0.1, 1.0 and 3.0 dpa are carried out.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Evaluation of Fracture Stress for the SiC Layer of TRISO-Coated Fuel Particles by A Modified Crush Testing

Fracture stress data for the chemical vapor deposition (CVD) SiC coatings of tri-isotropic (TRISO) carbon/silicon carbide coated fuel particles were obtained using a newly developed testing and evaluation method, and their relationship with microstructure investigated. A crush testing technique using a blanket foil at load-transferring contact has been developed for hemispherical shell SiC specimens based on finite element (FE) analysis results. Mean fracture stress varied with test material in the range of 330 650 MPa, and was connected to the combined characteristics of inner surface roughness and porosity.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Construction and experimental validation of a simple, compact, resealable, and reliable Vycor{sup ®} superleak assembly for use at low temperatures

A new method of constructing a superleak assembly for use in experiments involving {sup 4}He or {sup 3}He-{sup 4}He mixtures at very low temperatures is described. Superleaks are made of a porous medium with very small pores and channels. Superleaks are often incorporated in thermomechanical pumps, superfluid magnetic pumps, dilution refrigerators, and superfluid helium transfer systems. We used several cylindrical pieces of Vycor, a permeable glass with average pore diameter of 40 Å and porosity of 28%, as a candidate to be used in our superleak assembly. Our design is simple and compact. Our superleak assembly can be disassembled and easily reassembled for reuse. We successfully tested and validated this device at temperatures between 1.4 K and 2.7 K. We experienced no superfluid leaks into the surrounding vacuum. We also report that thermal cycling caused no performance degradation. It is our goal to share the design and construction techniques of this new superleak assembly.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A One-Year Study of the Diurnal Cycle of Meteorology, Clouds, and Radiation in the West African Sahel Region

The diurnal cycles of meteorological and radiation variables are analyzed during the wet and dry seasons over the Sahel region of West Africa during 2006 using surface data collected by the Atmospheric Radiation Measurement (ARM) program’s Mobile Facility, satellite radiation measurements from the Geostationary Earth Radiation Budget (GERB) instrument aboard Meteosat 8, and reanalysis products from the National Center for Environmental Prediction (NCEP). The meteorological analysis builds upon past studies of the diurnal cycle in the region by incorporating diurnal cycles of lower tropospheric wind profiles, thermodynamic profiles, integrated water vapor and liquid water measurements, and cloud radar measurements of frequency and location. These meteorological measurements are complemented by 3-hour measurements of the diurnal cycles of the TOA and surface shortwave (SW) and longwave (LW) radiative fluxes and cloud radiative effects (CREs), and the atmospheric radiative flux divergence (RFD) and atmospheric CREs. Cirrus cloudiness during the dry season is shown to peak in coverage in the afternoon, while convective clouds during the wet season are shown to peak near dawn and have an afternoon minimum related to the rise of the Lifting Condensation Level into the Saharan Air Layer. The LW and SW RFDs and CREs exhibit diurnal cycles during both seasons, but there is a relatively small difference in the LW cycles during the two seasons (10-30 Wm^(-2) depending on the variable and time of day). Small differences in the TOA CREs during the two seasons are overwhelmed by large differences in the surface SW CREs, which exceed 100 Wm^(-2). A significant surface SW CRE during the wet season combined with a negligible TOA SW CRE produces a diurnal cycle in the atmospheric CRE that is modulated primarily by the SW surface CRE, peaks at midday at ~150 Wm^(-2), and varies widely from day to day.

Marquardt-Collow, Allison↗

Sr- and Mn-doped LaAlO 3-δ for solar thermochemical H 2 and CO production

The increasing global appetite for energy within the transportation sector will inevitably result in the combustion of more fossil fuel. A renewable-derived approach to carbon-neutral synthetic fuels is therefore needed to offset the negative impacts of this trend, which include climate change. In this communication we report the use of nonstoichiometric perovskite oxides in two-step, solar-thermochemical water or carbon dioxide splitting cycles. We find that LaAlO 3 doped with Mn and Sr will efficiently split both gases. Moreover the H 2 yields are 9× greater, and the CO yields 6× greater, than those produced by the current state-of-the-art material, ceria, when reduced at 1350 °C and re-oxidized at 1000 °C. The temperature at which O 2 begins to evolve from the perovskite is fully 300 °C below that of ceria. The materials are also very robust, maintaining their redox activity over at least 80 CO 2 splitting cycles. This discovery has profound implications for the development of concentrated solar fuel technologies.

54 ENVIRONMENTAL SCIENCES↗

Oscillating flow loss test results in Stirling engine heat exchangers

The results are presented for a test program designed to generate a database of oscillating flow loss information that is applicable to Stirling engine heat exchangers. The tests were performed on heater/cooler tubes of various lengths and entrance/exit configurations, on stacked and sintered screen regenerators of various wire diameters and on Brunswick and Metex random fiber regenerators. The test results were performed over a range of oscillating flow parameters consistent with Stirling engine heat exchanger experience. The tests were performed on the Sunpower oscillating flow loss rig which is based on a variable stroke and variable frequency linear drive motor. In general, the results are presented by comparing the measured oscillating flow losses to the calculated flow losses. The calculated losses are based on the cycle integration of steady flow friction factors and entrance/exit loss coefficients.

Koester, G.↗

GPS Monitoring of Surface Change During and Following the Fortuitous Occurrence of the M(sub w) = 7.3 Landers Earthquake in our Network

Accomplishments: (1) Continues GPS monitoring of surface change during and following the fortuitous occurrence of the M(sub w) = 7.3 Landers earthquake in our network, in order to characterize earthquake dynamics and accelerated activity of related faults as far as 100's of kilometers along strike. (2) Integrates the geodetic constraints into consistent kinematic descriptions of the deformation field that can in turn be used to characterize the processes that drive geodynamics, including seismic cycle dynamics. In 1991, we installed and occupied a high precision GPS geodetic network to measure transform-related deformation that is partitioned from the Pacific - North America plate boundary northeastward through the Mojave Desert, via the Eastern California shear zone to the Walker Lane. The onset of the M(sub w) = 7.3 June 28, 1992, Landers, California, earthquake sequence within this network poses unique opportunities for continued monitoring of regional surface deformation related to the culmination of a major seismic cycle, characterization of the dynamic behavior of continental lithosphere during the seismic sequence, and post-seismic transient deformation. During the last year, we have reprocessed all three previous epochs for which JPL fiducial free point positioning products available and are queued for the remaining needed products, completed two field campaigns monitoring approx. 20 sites (October 1995 and September 1996), begun modeling by development of a finite element mesh based on network station locations, and developed manuscripts dealing with both the Landers-related transient deformation at the latitude of Lone Pine and the velocity field of the whole experiment. We are currently deploying a 1997 observation campaign (June 1997). We use GPS geodetic studies to characterize deformation in the Mojave Desert region and related structural domains to the north, and geophysical modeling of lithospheric behavior. The modeling is constrained by our existing and continued GPS measurements, which will provide much needed data on far-field strain accumulation across the region and on the deformational response of continental lithosphere during and following a large earthquake, forming the basis for kinematic and dynamic modeling of secular and seismic-cycle deformation. GPS geodesy affords both regional coverage and high precision that uniquely bear on these problems.

Miller, M. Meghan↗