Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “methyl esters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

In situ measurement of power conversion efficiency and molecular ordering during thermal annealing in P3HT:PCBM bulk heterojunction solar cells

Bulk heterojunction organic solar cells hold much promise as commercially viable sources of renewable energy due to their relatively inexpensive fabrication. Developing a fundamental knowledge of how processing conditions influence solar power conversion efficiency will enable rational and efficient design, optimization, and control of new organic solar cell materials. In this report, we use a combination of in situ current–voltage measurements and grazing-incidence wide-angle X-ray scattering experiments at elevated temperature to correlate the changes in photoconversion efficiency to the changes in the molecular ordering of a poly(3-hexylthiophene):[6,6]-phenyl-C₆₁-butyric acid methyl ester (P3HT:PCBM) bulk heterojunction active layer. In situ measurements of current–voltage characteristics were used to optimize the power conversion efficiency and the resulting thermal processing was in agreement with studies from repeated heating and cooling cycles. The improvements in short circuit current with thermal annealing were correlated to an increase in the population of face-on oriented crystallites of P3HT rather than improvements in molecular ordering of PCBM.

14 SOLAR ENERGY↗

Directed Self-assembly of Nanoparticles at the Polymer Surface by Highly Compressible Supercritical Carbon Dioxide

We report a versatile route for self-assembly of polymer-soluble nanoparticles at the polymer surface using highly compressible supercritical carbon dioxide (scCO{sub 2}). Polystyrene and poly(methyl methacrylate)-based nanocomposite thin films with functionalized polyhedral oligomeric silsesquioxane and phenyl C{sub 61} butyric acid methyl ester nanoparticles were prepared on Si substrates and exposed to scCO{sub 2} at different pressures under the isothermal condition of 36 C. The resultant structures could be then preserved by the vitrification process of the glassy polymers via quick pressure quench to atmospheric pressure and subsequently characterized by using various surface sensitive experimental techniques in air. We found that the surface segregation of these nanoparticles is induced in the close vicinity of P = 8.2 MPa where the excess absorption of the fluid into the polymers maximizes. However, when the film thickness becomes less than about 4R{sub g} thick (where R{sub g} is the radius of polymer gyration), the uniform dispersion of the nanoparticles is favorable instead even at the same CO{sub 2} conditions. We clarify that the phase transition is correlated with the emergence of a concentration gradient of the fluid at the polymer/CO{sub 2} interface and is a general phenomenon for different polymer-nanoparticle interactions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Recent progress in the morphology of bulk heterojunction photovoltaics

A review of current research in the characterization of the morphology of semiconducting polymer:fullerene bulk heterojunctions (BHJs) is presented. BHJs are complex blends of polymers and fullerenes with nanostructures that are highly dependent on materials, processing conditions, and post-treatments to films. Recent work on the study of the morphology of BHJs is surveyed. Emphasis is placed on emerging work on BHJs of poly(3-hexylthiophene), P3HT, and [6,6]-phenyl-C61-butyric acid methyl ester, PCBM, along with BHJs of donor–acceptor polymers that have high power conversion efficiency.

14 SOLAR ENERGY↗

Enhanced charge separation in organic photovoltaic films doped with ferroelectric dipoles

A key requirement for realizing efficient organic photovoltaic (OPV) cells is the dissociation of photogenerated electron-hole pairs (singlet-excitons) in the donor polymer, and charge-transfer-excitons at the donor–acceptor interface. However, in modern OPVs, these excitons are typically not sufficiently harnessed due to their high binding energy. Here, we show that doping the OPV active-layers with a ferroelectric polymer leads to localized enhancements of electric field, which in turn leads to more efficient dissociation of singlet-excitons and charge-transfer-excitons. Bulk-heterojunction OPVs based on poly(3-hexylthiophene):[6,6]-phenyl-C61-butyric acid methyl ester are fabricated. Upon incorporating a ferroelectric polymer as additive in the active-layer, power conversion efficiencies increase by nearly 50%, and internal quantum efficiencies approach 100% – indicating complete exciton dissociation at certain photon energies. Similar enhancements in bilayer-heterojunctions, and direct influence of ferroelectric poling on device behavior show that improved dissociation is due to ferroelectric dipoles rather than any morphological change. Enhanced singlet-exciton dissociation is also revealed by photoluminescence lifetime measurements, and predicted by simulations using a numerical device model.

36 MATERIALS SCIENCE↗

Low-Temperature, Solution-Processed Molybdenum Oxide Hole-Collection Layer for Organic Photovoltaics

We have utilized a commercially available metal-organic precursor to develop a new, low-temperature, solution-processed molybdenum oxide (MoO{sub x}) hole-collection layer (HCL) for organic photovoltaic (OPV) devices that is compatible with high-throughput roll-to-roll manufacturing. Thermogravimetric analysis indicates complete decomposition of the metal-organic precursor by 115 C in air. Acetonitrile solutions spin-cast in a N{sub 2} atmosphere and annealed in air yield continuous thin films of MoO{sub x}. Ultraviolet, inverse, and X-ray photoemission spectroscopies confirm the formation of MoO{sub x} and, along with Kelvin probe measurements, provide detailed information about the energetics of the MoO{sub x} thin films. Incorporation of these films into conventional architecture bulk heterojunction OPV devices with poly(3-hexylthiophene) and [6,6]-phenyl-C{sub 61} butyric acid methyl ester afford comparable power conversion efficiencies to those obtained with the industry-standard material for hole injection and collection: poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS). The MoO{sub x} HCL devices exhibit slightly reduced open circuit voltages and short circuit current densities with respect to the PEDOT:PSS HCL devices, likely due in part to charge recombination at Mo{sup 5+} gap states in the MoO{sub x} HCL, and demonstrate enhanced fill factors due to reduced series resistance in the MoO{sub x} HCL.

14 SOLAR ENERGY↗

New Insights into Dynamics and Morphology of P3HT:PCBM Active Layers in Bulk Heterojunctions

Organic photovoltaics (OPVs) are topic of extensive research for their potential application in solar cells. Recent work has led to the development of a coarse-grained model for studying poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C 61 -butyric acid methyl ester (PCBM) blends with molecular simulations. Here we provide further validation of the force field and use it to study the thermal annealing process of P3HT:PCBM blends. A key finding of our study is that, in contrast to a previous report, the annealing process does not converge at the short time scales reported. Rather, we find that the self assembly of the blends is characterized by three rate dependent stages that require much longer simulations to approach convergence. Using state-of-the- art high performance computing, we are able to study annealing at length and time scales commensurate with devices used in experiments. Our simulations show different phase segregated morphologies dependent on the P3HT chain length and PCBM volume fraction in the blend. For short chain lengths, we observed a smectic morphology containing alternate P3HT and PCBM domains. In contrast, a phase segregated morphology containing domains of P3HT and PCBM distributed randomly in space is found for longer chain lengths. Theoretical arguments justifying stabilization of these morphologies due to shape anisotropy of P3HT (rod-like) and PCBM (sphere-like) are presented. Furthermore, results on structure factor, miscibility of P3HT and PCBM, domain spacing and kinetics of phase segregation in the blends are presented in detail. Qualitative comparison of these results with small-angle neutron scattering experiments from literature is presented and an excellent agreement is found.

14 SOLAR ENERGY↗

Correlation of polymeric compatibilizer structure to its impact on the morphology and function of P3HT:PCBM bulk heterojunctions

Here we present the impact of various polymeric compatibilizers, including end-functionalized P3HTs and diblock copolymers containing P3HT, on the structure and function of poly(3-hexylthiophene) (P3HT):[6,6]-phenyl-C61-butyric acid methyl ester (PCBM) bulk heterojunctions. Careful analyses of small angle neutron scattering curves provide a measure of the miscibility of PCBM in P3HT, the average PCBM domain size, and the interfacial area between PCBM and the P3HT-rich phase in the uncompatibilized and compatibilized systems. Differential scanning calorimetry (DSC) also provides information regarding the changes in the crystallinity of P3HT due to the presence of the compatibilizer. Results show that most compatibilizers cause the domain sizes to decrease and the P3HT crystallinity to increase; however, some cause an increase in domain size, suggesting that they are not effective interfacial modifiers. The correlation of morphology with photovoltaic activity shows that the decreased domain size, increased crystallinity and increased interfacial area do not always result in improved power conversion efficiency (PCE). It appears that the introduction of an insulating molecule at the PCBM:P3HT interface as a compatibilizer results in a decrease in PCE. Thus, the presence of the compatibilizer at this interface dominates the photovoltaic activity, rather than the morphological control.

36 MATERIALS SCIENCE↗

A faux hawk fullerene with PCBM-like properties

Reaction of C 60 , C 6 F 5 CF 2 I, and SnH(n-Bu) 3 produced, among other unidentified fullerene derivatives, the two new compounds 1,9-C 60 (CF 2 C 6 F 5 )H (1) and 1,9-C 60 (cyclo-CF 2 (2-C 6 F 4 )) (2). The highest isolated yield of 1 was 35% based on C60. Depending on the reaction conditions, the relative amounts of 1 and 2 generated in situ were as high as 85% and 71%, respectively, based on HPLC peak integration and summing over all fullerene species present other than unreacted C60. Compound 1 is thermally stable in 1,2-dichlorobenzene (oDCB) at 160 °C but was rapidly converted to 2 upon addition of Sn 2 (n-Bu) 6 at this temperature. In contrast, complete conversion of 1 to 2 occurred within minutes, or hours, at 25 °C in 90/10 (v/v) PhCN/C 6 D 6 by addition of stoichiometric, or sub-stoichiometric, amounts of proton sponge (PS) or cobaltocene (CoCp 2 ). DFT calculations indicate that when 1 is deprotonated, the anion C 60 (CF 2 C 6 F 5 )- can undergo facile intramolecular SNAr annulation to form 2 with concomitant loss of F-. To our knowledge this is the first observation of a fullerene-cage carbanion acting as an S N Ar nucleophile towards an aromatic C–F bond. The gas-phase electron affinity (EA) of 2 was determined to be 2.805(10) eV by low-temperature PES, higher by 0.12(1) eV than the EA of C 60 and higher by 0.18(1) eV than the EA of phenyl-C 61 -butyric acid methyl ester (PCBM). In contrast, the relative E 1/2 (0/-) values of 2 and C 60 , -0.01(1) and 0.00(1) V, respectively, are virtually the same (on this scale, and under the same conditions, the E1/2(0/-) of PCBM is -0.09 V). Time-resolved microwave conductivity charge-carrier yield × mobility values for organic photovoltaic active-layer-type blends of 2 and poly-3-hexylthiophene (P3HT) were comparable to those for equimolar blends of PCBM and P3HT. The structure of solvent-free crystals of 2 was determined by single-crystal X-ray diffraction. The number of nearest-neighbor fullerene–fullerene interactions with centroid···centroid (⊙···⊙) distances of ≤10.34 Å is significantly greater, and the average ⊙···⊙ distance is shorter, for 2 (10 nearest neighbors; ave. ⊙···⊙ distance = 10.09 Å) than for solvent-free crystals of PCBM (7 nearest neighbors; ave. ⊙···⊙ distance = 10.17 Å). Finally, the thermal stability of 2 was found to be far greater than that of PCBM.

14 SOLAR ENERGY↗

Performance enhancement of fullerene based solar cells upon NIR laser irradiation

Photovoltaic performance enhancement of fullerene based solar cells was achieved upon exposure to near-infrared (NIR) laser pulses. In this work, the solar cells were fabricated with poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl C 61 -butyric acid methyl ester (PCBM) under ambient conditions. The cells were then post-treated with NIR femto-second laser pulses at 800 nm for different intervals of time. An enhancement of 50% in the power conversion efficiency was achieved for the devices with 15 minutes of NIR laser irradiation compared to that of the control device. The enhancement in the power conversion efficiency is attributed to the formation of a covalent linkage between P3HT and PCBM as suggested by Matrix-assisted laser desorption/ionization time of flight mass spectroscopic analysis on a blend of a thiophene oligomer and PCBM before and after NIR laser exposure.

36 MATERIALS SCIENCE↗

Efficient lipid extraction and quantification of fatty acids from algal biomass using accelerated solvent extraction (ASE)

Accelerated solvent extraction (ASE), a commercially available pressurized fluid extraction technique and conventional manual extraction were compared to identify the most effective chloroform–methanol extraction method for algal lipids. Using optimal ASE operating conditions (methanol/chloroform = 2 : 1 by vol, 100 °C, static time of 5 min, and four static cycles), the lipid contents of Chlorella vulgaris, C. sorokiniana, C. zofingiensis and Nannochloropsis gaditana were 27.5%, 25.8%, 15.2%, 29.8% of dry biomass, respectively. Here, the total fatty acid methyl ester (FAME) content of dry biomass from ASE extraction was found to be 1.3–2.7 fold higher than that from conventional manual extract from these species, demonstrating that ASE exhibited significant improvement for lipid and FAME recovery. Furthermore, ASE showed the capacity to extract all-cis-5,8,11,14,17-eicosapentaenoic acid (EPA) as 3.0% of dry biomass from Nannochloropsis gaditana suggesting that ASE has the potential to obtain polyunsaturated fatty acids (PUFAs) as well.

09 BIOMASS FUELS↗

Wide bandgap OPV polymers based on pyridinonedithiophene unit with efficiency >5%

We report the properties of a new series of wide band gap photovoltaic polymers based on the N -alkyl 2-pyridone dithiophene (PDT) unit. These polymers are effective bulk heterojunction solar cell materials when blended with phenyl-C 71 -butyric acid methyl ester (PC 71 BM). They achieve power conversion efficiencies (up to 5.33%) high for polymers having such large bandgaps, ca. 2.0 eV (optical) and 2.5 eV (electrochemical). As a result, grazing incidence wide-angle X-ray scattering (GIWAXS) reveals strong correlations between π–π stacking distance and regularity, polymer backbone planarity, optical absorption maximum energy, and photovoltaic efficiency.

14 SOLAR ENERGY↗

Vertical and lateral morphology effects on solar cell performance for a thiophene–quinoxaline copolymer:PC 70 BM blend

The distribution of electron donor and acceptor in the active layer is known to strongly influence the electrical performance of polymer solar cells for most of the high performance polymer:fullerene systems. The formulation of the solution from which the active layer is spincoated plays an important role in the quest for morphology control. We have studied how the choice of solvent and the use of small amounts of a low vapour pressure additive in the coating solution influence the film morphology and the solar cell performance for blends of poly[2,3-bis-(3-octyloxyphenyl)quinoxaline-5,8-diyl-alt-thiophene-2,5-diyl] (TQ1) and [6,6]-phenyl C 71 -butyric acid methyl ester (PC 70 BM). We have investigated the lateral morphology using atomic force microscopy (AFM) and scanning transmission X-ray microscopy (STXM), the vertical morphology using dynamic secondary ion mass spectrometry (d-SIMS) and variable-angle spectroscopic ellipsometry (VASE), and the surface composition using near-edge X-ray absorption fine structure (NEXAFS). The lateral phase-separated domains observed in films spincoated from single solvents, increase in size with increasing solvent vapour pressure and decreasing PC 70 BM solubility, but are not observed when 1-chloronaphthalene (CN) is added. A strongly TQ1-enriched surface layer is formed in all TQ1:PC 70 BM blend films and rationalized by surface energy differences. The photocurrent and power conversion efficiency strongly increased upon the addition of CN, while the leakage current decreased by one to two orders of magnitude. The higher photocurrent correlates with the finer lateral structure and stronger TQ1-enrichment at the interface with the electron-collecting electrode. This indicates that the charge transport and collection are not hindered by this polymer-enriched surface layer. Neither the open-circuit voltage nor the series resistance of the devices are sensitive to the differences in morphology.

36 MATERIALS SCIENCE↗

Parallel bulk heterojunction photovoltaics based on all-conjugated block copolymer additives

We demonstrated that the addition of block copolymers to binary donor–acceptor blends represents an effective approach to target equilibrium, co-continuous morphologies of interpenetrating donors and acceptors in our recent study. We report a study of the impact of all-conjugated poly(thieno[3,4-b]-thiophene-co-benzodithiophene)-b-polynaphthalene diimide (PTB7-b-PNDI) block copolymer additives on the electronic properties and photovoltaic performance of bulk heterojunction organic photovoltaic active layers comprised of a PTB7 donor and a phenyl-C61-butyric acid methyl ester (PCBM61) acceptor. We find that small amounts of BCP additives lead to improved performance due to a large increase in the device open-circuit voltage (VOC), and the VOC is pinned to this higher value for higher BCP additive loadings. Such results contrast prior studies of ternary blend OPVs where either a continuous change in VOC or a value of VOC pinned to the lowest value is observed. We hypothesize and provide evidence in the form of device and morphology analyses that the impact of VOC is likely due to the formation of a parallel bulk heterojunction made up of isolated PCBM and PNDI acceptor domains separated by intermediate PTB7 donor domains. Our work demonstrates that all-conjugated block copolymers can be utilized as additives to both dictate morphology and modulate the electronic properties of the active layer.

36 MATERIALS SCIENCE↗

Building intermixed donor–acceptor architectures for water-processable organic photovoltaics

A modified synthesis method for aqueous nanoparticle printing inks, based upon vacuum-assisted solvent removal, is reported. Poly(3-hexylthiophene):phenyl C 61 butyric acid methyl ester nanoparticle inks were prepared via this modified miniemulsion method, leading to both an improvement in photoactive layer morphology and a substantial reduction in the ink fabrication time. A combination of UV-visible spectroscopy, photoluminescence spectroscopy and scanning transmission X-ray microscopy measurements revealed a nanoparticle morphology comprising highly intermixed donor–acceptor domains. Consistent with these measurements, dynamic mechanical thermal analysis of the nanoparticles showed a glass transition temperature (T g ) of 104 °C, rather than a pure polymer phase or pure fullerene phase T g . Together the spectroscopy, microscopy and thermomechanical data indicate that rapid solvent removal generates a more blended nanoparticle morphology. As such, this study highlights a new experimental lever for optimising nanostructure in the photoactive layer of nanoparticulate organic photovoltaic devices by enabling highly intermixed donor–acceptor architectures to be built from customised nanoparticulate inks.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A new family of fullerene derivatives: fullerene-curcumin conjugates for biological and photovoltaic applications

The synthesis and characterization of a family of [60]fullerocurcuminoids obtained via Bingel reactions is reported. The new C 60 derivatives include curcumin and curcuminoids with a variety of end groups. Preliminary biological experiments show the potential activity of the compound containing a curcumin addend, which exhibits moderate anti-HIV-1 and radical scavenger properties, but no anti-cancer activity. In addition, the new fullerocurcuminoids exhibit HOMO/LUMO energy levels that are reasonably matched with those of perovskites and when they were tested in perovskite solar cells (PSCs) as the electron transporting material (ETM), photoconversion efficiencies ranging from 14.04–14.95% were obtained, whereas a value of 16.23% was obtained for [6,6]-phenyl-C61-butyric acid methyl ester (PC 61 BM) based devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Is there such a thing as a molecular organic alloy?

In inorganic materials, an alloy is a mixture of two or more substances that generally exhibits electronic and/or physical properties that differ from those of its constituents. In organic systems, the formation of a “molecular alloy” comprising mixtures of molecular organic materials has also been proposed. We test the validity of this concept via the study of the optoelectronic properties of a ternary system that has previously been identified to form a molecular acceptor alloy, namely a blend of a poly(3-hexylthiophene) (P3HT) donor, with two acceptors indene-C 60 bisadduct (ICBA) and phenyl-C 61 -butyric acid methyl ester (PC 61 BM) [R. A. Street, et al., J. Am. Chem. Soc., 2013, 135, 986–989]. Using photoelectron spectroscopy, we find that the ICBA:PC 61 BM blend shows the same highest occupied molecular orbital and exciton energies as that of ICBA, indicating the absence of a new exciton state in the blend. Furthermore, charge transfer state spectra of ternary blends are found to comprise a simple linear superposition of the corresponding binaries. From these results, no evidence of new, emergent electronic states is found to support the existence of a molecular alloy in this system. To our knowledge there is as yet no clear evidence of the existence of an alloy in any organic semiconductor system. Finally, we discuss the criteria that should be met by a molecular organic alloy and procedures needed for their unambiguous identification.

36 MATERIALS SCIENCE↗

Improving the efficiencies of small molecule solar cells by solvent vapor annealing to enhance J-aggregation

Here, we report highly efficient small molecule organic solar cells (SM-OSCs) based on a porphyrin derivative electron donor of ZnP2-DPP and an electron acceptor of [6,6]-phenyl-C 61 -butyric acid methyl ester (PC 60 BM) by using a solvent vapor annealing (SVA) method with a series of low boiling solvents. Absorption spectral studies indicate that carbon disulfide (CS 2 ) SVA induces J-aggregation in blend films accompanied by expanded and enhanced absorption which contributes largely to the fabrication of broader light response and larger short-circuit current (J SC ) solar cell devices. In addition, we systematically analyze the relationship between the film morphology and device performance. Finally, the electronic study shows that the CS 2 SVA-treated device showed a higher exciton generation rate and enhanced carrier collection efficiency. And the morphology study indicates that the blend films treated with CS2 SVA exhibit tighter molecular packing, better crystallization and an appropriate phase separation length scale. In other words, these collective electronic and morphological features correlate well with the champion J SC , the fill factor (FF) and the power conversion efficiency (PCE) of the CS 2 treated devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Neutral rhenium( i ) tricarbonyl complexes with sulfur-donor ligands: anti-proliferative activity and cellular localization

Rhenium(I) tricarbonyl complexes are widely studied for their cell imaging properties and anti-cancer and anti-microbial activities, but the complexes with S-donor ligands remain relatively unexplored. A series of six fac-[Re(NN)(CO) 3 (SR)] complexes, where (NN) is 2,2'-bipyridyl (bipy) or 1,10-phenanthroline (phen), and RSH is a series of thiocarboxylic acid methyl esters, have been synthesized and characterized. Cellular uptake and anti-proliferative activities of these complexes in human breast cancer cell lines (MDA-MB-231 and MCF-7) were generally lower than those of the previously described fac-[Re(NN)(CO) 3 (OH 2 )]+ complexes; however, one of the complexes, fac-[Re(CO) 3 (phen)(SC(Ph)CH 2 C(O)OMe)] (3b), was active (IC 50 ~ 10 μM at 72 h treatment) in thiol-depleted MDA-MB-231 cells. Moreover, unlike fac-[Re(CO) 3 (phen)(OH 2 )]+, this complex did not lose activity in the presence of extracellular glutathione. Taken together these properties show promise for further development of 3b and its analogues as potential anti-cancer drugs for co-treatment with thiol-depleting agents. Conversely, the stable and non-toxic complex, fac-[Re(bipy)(CO) 3 (SC(Me)C(O)OMe)] (1a), predominantly localized in the lysosomes of MDA-MB-231 cells, as shown by live cell confocal microscopy (λ ex = 405 nm, λ em = 470–570 nm). It is strongly localized in a subset of lysosomes (25 μM Re, 4 h treatment), as shown by co-localization with a Lysotracker dye. Longer treatment times with 1a (25 μM Re for 48 h) resulted in partial migration of the probe into the mitochondria, as shown by co-localization with a Mitotracker dye. These properties make complex 1a an attractive target for further development as an organelle probe for multimodal imaging, including phosphorescence, carbonyl tag for vibrational spectroscopy, and Re tag for X-ray fluorescence microscopy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗