High-Energy Lateral Mapping (HELM) Studies of Inhomogeneity and Failure Mechanisms in NMC622/Li Pouch Cells
Explore the source record for details and available documents.
99 GENERAL AND MISCELLANEOUS↗
SEARCH · Engineering Papers
Results for “manufacturing process”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Development of a Generalized Residual Stress Inversion Technique
Residual stress is a common result of manufacturing processes, but it is one that is often overlooked in design and qualification activities. There are many reasons for this oversight, such as lack of observable indicators and difficulty in measurement. Traditional relaxation-based measurement methods use some type of material removal to cause surface displacements, which can then be used to solve for the residual stresses relieved by the removal. While widely used, these methods may offer only individual stress components or may be limited by part or cut geometry requirements. Diffraction-based methods, such as X-ray or neutron, offer non-destructive results but require access to a radiation source. With the goal of producing a more flexible solution, this LDRD developed a generalized residual stress inversion technique that can recover residual stresses released by all traction components on a cut surface, with much greater freedom in part geometry and cut location. The developed method has been successfully demonstrated on both synthetic and experimental data. The project also investigated dislocation density quantification using nonlinear ultrasound, residual stress measurement using Electronic Speckle Pattern Interferometry Hole Drilling, and validation of residual stress predictions in Additive Manufacturing process models.
42 ENGINEERING↗
In situ liquid SIMS analysis of uranium oxide
Trace analysis of nuclear materials in solid particles collected in the environment or particles in liquid slurry generated in nuclear material manufacturing processes can pinpoint elemental, organic, and isotopic signatures of nuclear fuel cycle activities and processes. Such information can support nuclear safeguards programs by increasing our ability to detect undeclared nuclear materials, routine activities for safeguarding at declared facilities, and illicit activities. However, trace radioactive material analysis in liquids and slurries is challenging using bulk approaches. For example, one drawback of sensitive analysis such as inductively coupled plasma mass spectrometry (ICP-MS) is that sample is consumed or destroyed as a result of the technical approach. We developed a vacuum compatible microfluidic interface to enable surface analysis of liquids and liquid-solid interactions using time-of-flight secondary ion mass spectrometry (ToF-SIMS). In this work, we illustrate initial results of liquid standards containing uranium using in situ liquid SIMS. Specifically a series of diluted uranium standards used for ICPMS analysis were studied and the limit of detection was estimated. Since the liquid SIMS analysis is almost nondestructive, the same sample can be analyzed by other more destructive approaches afterwards or saved for future references. Consequently, multimodal analysis is possible. Our results demonstrate that in situ liquid SIMS can be used as a new approach to analyze radioactive materials in liquid and slurry forms of relevance to the IAEA safeguards missions.
In situ liquid ToF-SIMS, uranium, limit of detecti↗
Radio-Frequency Rapid Thermal Processing Enabling Spatial Phase Transformation and Nanocrystallization of Soft Magnetic Amorphous Alloys
Thermal processing of soft magnetic amorphous and nanocrystalline alloys is explored under the influence of radio-frequency induction-heating techniques. Direct induction-heating concepts based on longitudinal and transverse flux heating are examined and the details of electromagnetic fields interaction with metallic strips are discussed by analytical calculations as well as finite element analysis. Initial experimental results confirming spatial control of phase transformations and nanocrystallization within a single strip of Finemet Fe-based amorphous ribbons are reported. Here, the degree to which primary and secondary crystallization temperature are achieved depends on the spacing between the ribbon relative to the induction coil as well as the coil design and configuration. For transverse coil configurations, the local temperature and therefore microstructural evolution is different across the lateral dimension of processed ribbons, with reduced gap sizes producing enhanced peak temperatures and larger temperature distributions with greater spatial variation in microstructure. In addition, indirect susceptor-based induction heating under tension is performed and the impact of microstructure is demonstrated. Herein, potential for exploiting spatially optimized phase transformations is illustrated through electromagnetic field–assisted processing in a scalable manufacturing process with amorphous and nanocrystalline soft magnetic alloys.
36 MATERIALS SCIENCE↗
Understanding solidification of near eutectic alloy using Cellular Automata (CA)
The solidification microstructure of an alloy strongly influences the mechanical properties. Dendritic and eutectic solidification are two important pathways of alloy solidification. The formation of phases, and their size and distribution depend on which pathway to take. In contrast to the Scheil model that has been widely used in describing the solidification pathways of alloys manufactured from conventional casting approach, more sophisticated solidification models are required to describe the state-of-the art manufacturing processes, such as additive manufacturing where distinctly different phase morphology, size and distribution than conventional casting can form, due to the vast difference in cooling conditions. Therefore, this work is to develop a computational Cellular Automata framework which includes the modeling of nucleation and growth of dendritic and eutectic solidification, as well as their competition as a function of alloy composition, undercooling and cooling rate. Further, after individual solidification models were validated against analytical solutions, the models were then combined to predict the competition between dendritic and eutectic solidification in alloys with off-eutectic compositions. This work predicts increased cooling rates suppress the dendritic solidification and promote eutectic solidification. Although quantitative validation is needed, this finding is consistent with qualitative observation in literature.
36 MATERIALS SCIENCE↗
Alternating conduction and convection drying of paper – an experimental analysis with a continuous data acquisition approach
In conventional multi-cylinder drying of paper and board, both conductive drying from steam-heated dryer cylinders and convective drying by flowing air over the paper surface in the pockets are used. Conductive drying from steam-heated drying cylinders is a critical component in providing the necessary thermal energy to paper and board as they dry. Steam temperature and internal and external resistances at the contacting surface are critical process parameters influencing the conductive drying process. An experimental setup was developed to study the alternating conductive and convective drying of paper and board. Paper sheet moisture, temperature, and temperature distribution within the heated platen and the instantaneous heat flux as the sheet was being dried were measured. The instantaneous heat flux, contact heat transfer coefficient, and drying rates were determined as drying proceeds. Experimental results, as well as comparisons to literature and commercial data, are presented. The conductive heat transfer coefficients determined were compared to traditional correlations normally used in the modeling of paper drying. Similarly, the convective heat and mass transfer coefficients are also determined and compared to literature data. In addition to the evaluation of alternating conductive and convective drying characteristics of paper and board, the potential inclusion of auxiliary energy components will also be included. Experimental results from the conduction and convection drying system are presented. Furthermore, this data will be useful in process development, intensification of manufacturing processes, and modeling and simulation of paper drying processes.
42 ENGINEERING↗
Techno-Economic Assessment of a Novel Continuous Hot-Roll Process for Manufacturing Nanograin NdFeB Magnets
Not Available
Shakelly, Neha↗
A Hybrid Aerosol Jet Printing and Electrochemical Deposition Process for Manufacturing Multi-Layer Inductors and Transformers
Explore the source record for details and available documents.
Tsui, Lok-Kun↗
Advanced Materials & Manufacturing Technology (AMMT): Development of Additive Manufacturing Agnostic Process Parameter Procedure, 316H Stainless Steel Readiness Level Data Sets, and Machine Maintenance Plan
The University of California, Davis is involved in a project to deploy and enhance an artificial intelligence (AI) system for predicting and preventing plasma disruptions on the DIII D tokamak, under the funding from Department of Energy DE-SC0023500 (title: AI/Deep Learning FRNN Software for Prediction & Real-Time Control of DIII-D Plasma Control System (PCS)). The overarching goal is to demonstrate that real-time, AI-guided intervention can proactively modify the plasma state to avoid or mitigate disruptions—a critical challenge for the future of fusion energy.
36 MATERIALS SCIENCE↗
Efficient Silicon Carbide (SiC) Fiber Manufacture: Continuous Processing of Novel Precursors via Modified Material Handling
General Atomics Electromagnetic Systems (GA-EMS) together with The Nonwovens Institute (NWI) and Harper International have executed on a development project to improve the production efficiency and reduce the production cost of silicon carbide (SiC) fiber – a critical material that advances US energy security and aerospace leadership. In the first budget period (BP1), the modified tow throughput (MTT) apparatus was developed, enabling fiber spinning in the form of loose coils rather than tightly packed spools (Figure 1) for batch processing of SiC fiber. This coil-based approach was proven to be capable of uniform fiber crosslinking and ceramic conversion, as well as demonstrating key process efficiencies while meeting the program fiber property targets.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Competitiveness Improvement Project Informational Workshop
The National Renewable Energy Laboratory (NREL) is hosted an in-person workshop and webinar for the distributed wind Competitiveness Improvement Project (CIP) on Tuesday, December 17, 2019, at NREL's Flatirons Campus. The CIP is a periodic solicitation issued by NREL on behalf of the U.S. Department of Energy's Wind Energy Technologies Office. Through a competitive process, component suppliers and manufacturers of small- to medium-sized wind turbine technology are awarded cost-shared subcontracts to optimize their designs, develop advanced manufacturing processes, and perform turbine testing. The CIP aims to make wind energy cost competitive with other distributed generation technologies and increase the number of wind turbine designs certified to national performance and safety standards.
17 WIND ENERGY↗
Process for manufacturing SiC composite ceramics
A method is described for manufacturing a ceramic composite structure. The method includes wrapping ceramic fibers (22), such as SiC fibers, about the external surface of at least one form. The method further includes heating the wrapped fibers (22) to a temperature no greater than a first temperature, infiltrating voids (24) in the wrapped fibers (22) with the ceramic composite in a first vessel (12) at the first temperature, transferring the infiltrated wrapped fibers (22) from the first vessel (12) to a second vessel (14), distinct from the first vessel (12), and coating the infiltrated wrapped fibers (22) with the ceramic composite in the second vessel (14) at a second temperature, higher than the first temperature.
Lahoda, Edward J.↗
Powder Injection Molding Processes for Manufacture of Fast Reactor Nuclear Fuels
Explore the source record for details and available documents.
Moo, Patrick John [J. Foster & Associates.; J. Fos↗
The National Laboratory of the Rockies Strengthens U.S. Critical Minerals Supply Chains
The National Laboratory of the Rockies (NLR) is working to overcome bottlenecks and secure the U.S. critical mineral supply chain - delivering lower-cost, lower-risk pathways from unconventional and secondary feedstocks to validated products. NLR achieves this through cross-sector partnerships to advance U.S. critical minerals across the mining, processing, manufacturing, usage, and end-of-life stages.
29 ENERGY PLANNING, POLICY, AND ECONOMY↗
Editorial: Multi-Omics Technologies for Optimizing Synthetic Biomanufacturing
Industrial manufacturing endures as an essential human activity yielding a variety of useful products; it plays a significant role in the global economy with huge impacts in everyday life. However, the manufacturing process requires consumption of various raw materials (especially petroleum derivatives), generates a variety of harmful waste products, causes pollution, and is energetically inefficient. Biological manufacturing from sustainable, affordable, and scalable feedstocks potentially enables the displacement of the entire portfolio of currently available products produced by industrial processes, enabling the manufacturing of renewable and eco-friendly products (Clomburg et al., 2017). Thus, successful development of a robust biomanufacturing strategy and technology platform, based on the latest advances in synthetic biology and chemical catalysis, will decrease both the cost and production time compared with previous manufacturing processes. Development of biomanufacturing processes using a synthetic biology platform requires the multidisciplinary efforts of science and engineering fields including molecular biology, microbiology, genetic engineering, informatics, metabolic modeling and chemical or process engineering (El Karoui et al., 2019).
59 BASIC BIOLOGICAL SCIENCES↗
Coupling of Spark Plasma Sintering with Advanced Modeling to Enable Process Scale-Up: Presentation to DOE-NE [Slides]
The research goal of this project is to develop at Idaho National Laboratory (INL) a first-of-its-kind Multiphysics Object-Oriented Simulation Environment (MOOSE)-based, multiscale, multiphysics spark plasma sintering (SPS) modeling and simulation code application, termed “Freya.” Freya will simulate the thermo-mechanical-electrical aspects of the SPS fabrication process and will be paired with lower length scale sub-models, such as phase-field, to predict the resulting microstructure. SPS is an advanced manufacturing process that can be used to solve a variety of material manufacturing challenges; however, this process is an extremely challenging problem for modeling and simulation. The SPS process is inherently multiphysics and multi-scale, with the macroscale electro-thermo-mechanical behavior linked intricately to the microstructure evolution of the part being sintered. Accurate modeling and simulation tools, specifically geared towards the SPS process, are needed to predict the influence of the multiple variables involved in the manufacturing process. Modeling and simulation accuracy is achieved and demonstrated through comparison to multiple validation experiments. The validation efforts for Freya include both separate effects and complete multiphysics SPS process experiments. One of the key benefits this Laboratory Directed Research & Development (LDRD) project offers stems from the emphasis placed on experimental validation of the Freya models, both on the individual length scales and of the final coupled multiscale multiphysics simulations. Experimental validation of Freya’s multiscale coupling capability provides the technical credibility necessary for potential future industry and research partners to accept the simulation predictions.
36 MATERIALS SCIENCE↗
Towards developing multiscale-multiphysics models and their surrogates for digital twins of metal additive manufacturing
Artificial intelligence (AI) embedded within digital models of manufacturing processes can be used to improve process productivity and product quality significantly. The application of such advanced capabilities particularly to highly digitalized processes such as metal additive manufacturing (AM) is likely to make those processes commercially more attractive. AI capabilities will reside within Digital Twins (DTs) which are living virtual replicas of the physical processes. DTs will be empowered to operate autonomously in a diagnostic control capacity to supervise processes and can be interrogated by the practitioner to inform the optimal processing route for any given product. The utility of the information gained from the DTs would depend on the quality of the digital models and, more importantly, their faster-solving surrogates which dwell within DTs for consultation during rapid decision-making. In this article, we point out the exceptional value of DTs in AM and focus on the need to create high-fidelity multiscale-multiphysics models for AM processes to feed the AI capabilities. We identify technical hurdles for their development, including those arising from the multiscale and multiphysics characteristics of the models, the difficulties in linking models of the subprocesses across scales and physics, and the scarcity of experimental data. We discuss the need for creating surrogate models using machine learning approaches for real-time problem-solving. We further identify non-technical barriers, such as the need for standardization and difficulties in collaborating across different types of institutions. We offer potential solutions for all these challenges, after reflecting on and researching discussions held at an international symposium on the subject in 2019. Here, we argue that a collaborative approach can not only help accelerate their development compared with disparate efforts, but also enhance the quality of the models by allowing modular development and linkages that account for interactions between the various sub-processes in AM. A high-level roadmap is suggested for starting such a collaboration.
36 MATERIALS SCIENCE↗
Techno-Economic Wind Blade Manufacturing Model to Identify Opportunities for Cost Improvements Phase II IACMI Project 4.6/4.8
In IACMI Project 4.6 and IACMI Project 4.8, an Excel-based Techno-Economic Model (TEM) of the manufacturing process for composite wind turbine blades and a DELMIA Factory Flow Simulation of a generic wind blade manufacturing facility was developed. Together, these two tools provide a combined economic modeling capability that accounts for the material, labor, overhead and full-lifecycle operating costs associated with wind blade manufacturing as well as the impact of process flow and factory layout on overall manufacturing efficiency. The tools provide a novel means of detailed comparative analysis of the economic feasibility of proposed technologies and process changes for blade manufacturing. The modeling tools were developed with close support from members of industry and visits to multiple blade manufacturing facilities. With industry oversight, a detailed generalized manufacturing process plan and facility layout were developed with manufacturing parameters, material costs and economic factors based on historical data. Dassault Systèmes and the University of Texas at Dallas (UTD) contributed to the development of the Techno-Economic Model by providing macros to enable the generation of Bill of Material (BOM) data from a 3D blade design in either CATIA or NuMAD format, respectively. The TEM was built with the capability to directly import a Bill of Materials for economic analysis, and with the addition of the macros provided by Dassault and UTD, the TEM can directly import blade designs from both CATIA and NuMAD file formats. The modeling tools developed in Project 4.6 were used to investigate four wind blade manufacturing concepts in detail and select one to explore with laboratory-scale experimentation in Project 4.8. The four manufacturing concepts that were investigated were down-selected by the full project team from a larger list of concepts. The selections were made based on a number of criteria ranking viability and level of interest for each concept. The ‘One-Step Close’ manufacturing concept was ultimately selected for investigation in Project 4.8 and the demonstration was performed at the NREL CoMET facility. The TPI advanced manufacturing facility in Warren, RI contributed the production of several prototype components, the designs for which were developed by Janicki Industries. The demonstration project provided clear indication of the viability of the One-Step Close manufacturing concept for blade manufacturing and good validation of the Techno-Economic Model’s prediction of its economic impact.
17 WIND ENERGY↗