Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “least square approximations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Free-Spinning and Tumbling Tests of a 1/16-Scale Model of the McDonnell XP-85 Airplane

The teat results showed that with either of the three tail arrangements, the model usually spun in flat attitudes with oscillations about the lateral and longitudinal axes. In general, full reversal of the rudder pedals did not stop the spinning rotation. To make the model satisfactorily meet-the spin-recovery requirements it was found that installation of either a very large ventral fin (l7.9 square feet, full scale) below the tail or a somewhat smaller ventral fin and rudder (12.4 square feet, total . full-scale area) with a rudder throw of at least +/-22deg was required. Either a 21.3-foot tail parachute or a 6.4-foot wing-tip parachute (drag coefficient approximately 0.70) appears necessary as an emergency spin-recovery device during demonstration spins.

Klinar, Walter J.↗

A Comparative Study of Interferometric Regridding Algorithms

THe paper discusses regridding options: (1) The problem of interpolating data that is not sampled on a uniform grid, that is noisy, and contains gaps is a difficult problem. (2) Several interpolation algorithms have been implemented: (a) Nearest neighbor - Fast and easy but shows some artifacts in shaded relief images. (b) Simplical interpolator - uses plane going through three points containing point where interpolation is required. Reasonably fast and accurate. (c) Convolutional - uses a windowed Gaussian approximating the optimal prolate spheroidal weighting function for a specified bandwidth. (d) First or second order surface fitting - Uses the height data centered in a box about a given point and does a weighted least squares surface fit.

Hensley, Scott↗

Empirical correction for earth sensor horizon radiance variation

A major limitation on the use of infrared horizon sensors for attitude determination is the variability of the height of the infrared Earth horizon. This variation includes a climatological component and a stochastic component of approximately equal importance. The climatological component shows regular variation with season and latitude. Models based on historical measurements have been used to compensate for these systematic changes. The stochastic component is analogous to tropospheric weather. It can cause extreme, localized changes that for a period of days, overwhelm the climatological variation. An algorithm has been developed to compensate partially for the climatological variation of horizon height and at least to mitigate the stochastic variation. This method uses attitude and horizon sensor data from spacecraft to update a horizon height history as a function of latitude. For spacecraft that depend on horizon sensors for their attitudes (such as the Total Ozone Mapping Spectrometer-Earth Probe-TOMS-EP) a batch least squares attitude determination system is used. It is assumed that minimizing the average sensor residual throughout a full orbit of data results in attitudes that are nearly independent of local horizon height variations. The method depends on the additional assumption that the mean horizon height over all latitudes is approximately independent of season. Using these assumptions, the method yields the latitude dependent portion of local horizon height variations. This paper describes the algorithm used to generate an empirical horizon height. Ideally, an international horizon height database could be established that would rapidly merge data from various spacecraft to provide timely corrections that could be used by all.

Hashmall, Joseph A.↗

Stratospheric temperature profile from balloon-borne measurements of the 10.4-micron band of CO2

The technique of nonlinear least squares spectral curve fitting has been used to derive the stratospheric vertical temperature profile from balloon-borne measurements of the 10.4 micron band of CO2. The spectral data were obtained at sunset with the approximately 0.02 per cm resolution University of Denver interferometer system from a float altitude of 33.5 km near Alamogordo, New Mexico, on 23 March 1981. The r.m.s. deviation between the retrieved temperature profile and correlative radiosonde measurements is 2.2 K.

Rinsland, C. P.↗

The Moderate Resolution Imaging Spectrometer-tilt (MODIS-T)

There will be several state-of-the-art spectrometers in operation on the NASA Polar Oribting Platform (NPOP-1) as part of the Earth Observing System. The Moderate Resolution Imaging Spectrometer (MODIS) will consist of two imaging spectroradiometric instruments, one nadir-viewing (MODIS-N) and the other tiltable (MODIS-T) for ocean observation and land bidirectional reflectance studies. The MODIS-T instrument is required to cover the wavelength range of 400 to 880 nm in approximately 15 steps, have less than 2.3 percent instrument-induced polarization, be calibrated to an absolute radiometric accuracy of at least 5 percent over the full dynamic range of the instrument, have a 1.1 kilometer square instantaneous field of view at nadir, and be capable of + or - 50-deg along-track tilt.

Magner, Thomas J.↗

A case study of view-factor rectification procedures for diffuse-gray radiation enclosure computations

The view factors which are used in diffuse-gray radiation enclosure calculations are often computed by approximate numerical integrations. These approximately calculated view factors will usually not satisfy the important physical constraints of reciprocity and closure. In this paper several view-factor rectification algorithms are reviewed and a rectification algorithm based on a least-squares numerical filtering scheme is proposed with both weighted and unweighted classes. A Monte-Carlo investigation is undertaken to study the propagation of view-factor and surface-area uncertainties into the heat transfer results of the diffuse-gray enclosure calculations. It is found that the weighted least-squares algorithm is vastly superior to the other rectification schemes for the reduction of the heat-flux sensitivities to view-factor uncertainties. In a sample problem, which has proven to be very sensitive to uncertainties in view factor, the heat transfer calculations with weighted least-squares rectified view factors are very good with an original view-factor matrix computed to only one-digit accuracy. All of the algorithms had roughly equivalent effects on the reduction in sensitivity to area uncertainty in this case study.

Taylor, Robert P.↗

A Systematic Solution Approach for Neutron Transport Problems in Diffuse Regimes

A systematic solution approach for the neutron transport equation, based on a least-squares finite-element discretization, is presented. This approach includes the theory for the existence and uniqueness of the analytical as well as of the discrete solution, bounds for the discretization error, and guidance for the development of an efficient multigrid solver for the resulting discrete problem. To guarantee the accuracy of the discrete solution for diffusive regimes, a scaling transformation is applied to the transport operator prior to the discretization. The key result is the proof of the V-ellipticity and continuity of the scaled least-squares bilinear form with constants that are independent of the total cross section and the absorption cross section. For a variety of least-squares finite-element discretizations this leads to error bounds that remain valid in diffusive regimes. Moreover, for problems in slab geometry a full multigrid solver is presented with V(1, 1)-cycle convergence rates approximately equal to 0.1, independent of the size of the total cross section and the absorption cross section.

Manteuffel, T. A.↗

Decline in Aerobic Fitness After Long-Term Stays on the International Space Station

U.S. and non-Russian International Partner astronauts who participate in long-term International Space Station (ISS) expeditions perform submaximal cycle exercise tests before, during, and after space flight. The heart rate (HR) and oxygen uptake (VO2) responses to exercise are used to estimate peak VO2 (EVO2pk). Purpose: To determine if the following factors are associated with the preflight-to-post flight change in EVO2pk: gender, age, body weight (BW), number of aerobic exercise sessions/wk- during flight, length of flight, EVO2pk measured before and late during the flight, ISS Expedition number and time between landing and the first post flight test. Methods: Records of 37 ISS astronauts (30 male, BW=81.6 plus or minus 8.6 kg; 7 female BW=66.1 plus or minus 4.9 kg [mean plus or minus SD]), age 46 plus or minus 4 years, were retrospectively examined. Peak HR and VO2 were measured approximately 9 months before flight to establish the test protocol. The submaximal cycle test consisted of three 5-minute stages designed to elicit 25, 50, and 75% of VO2pk. EVO2pk was calculated using linear least-squares extrapolation of average HR and VO2 during the last minute of each stage to predict VO2 at maximal HR. VO2 was not measured during flight and was assumed to not be different from preflight. Testing was performed 45 days before launch, late during flight, and during the week after landing. A random-intercept multivariate model was used to determine which characteristics significantly contributed to post flight EVO2pk. Results: In-flight aerobic exercise averaged 5.4 plus or minus 1.2 sessions/wk. ISS flight duration averaged 163 plus or minus 39 d. Mean EVO2pk values were 3.41 plus or minus 0.64 L (raised dot) per minute before flight, 3.09 plus or minus 0.57 L (raised dot) per minute late in flight, and 3.02 plus or minus 0.65 L (raised dot) per minute after flight. Late- and after-flight values were lower (p less than 0.05) than preflight values and did not differ from each other. Time between landing and post flight testing was 4.5 plus or minus 1.6 days. The only factor significantly associated with the post flight EVO2pk value was the late-flight EVO2pk score. Conclusion: Testing performed late during a mission provides a prediction of EVO2pk after landing. This approach may be implemented during longer missions.

Lynn, Peggy A.↗

Recommendations for Using Noise Monitors to Estimate Noise Exposure During X-59 Community Tests

A low fidelity simulation approach is used to explore how to place and use noise monitors during X-59 QueSST community tests, where people’s annoyance to the noise produced by the X-59 aircraft will be gathered. Several recommendations are provided including: 1) the desired number of sparsely spaced noise monitor sites within the survey area, 2) whether to group and average measurements across multiple noise monitors located at a site, 3) what spacing should be used if grouped noise monitors are used, 4) an approach to mitigate ambient noise contamination at the measurement sites, 5) a method to combine empirical and predicted dose estimates to provide a single dose estimate for respondents, and 6) assessing how changes in turbulence intensity and array configuration affect dose uncertainty. To make these recommendations, the error that is expected when fitting contrived, smoothly varying sonic boom “reference exposure surfaces” is studied when a spatially sparse and scattered set of samples is used as responses for the fit. The reference exposure surfaces mimic the sonic boom exposure at ground level that might be expected in the X-59 survey area in the absence of atmospheric turbulence, ambient noise, and other localized effects. The spatial extent of these surfaces varies and is representative of the different survey area sizes that might be expected during future X-59 community overflight tests. These contrived reference surfaces are sampled, and those reference samples are then perturbed to mimic atmospheric turbulence, ambient noise and other localized effects that might affect noise monitor measurements within overflown communities. Two different surface fitting methods are investigated when fitting these perturbed samples to approximate the reference surface. The first method uses interpolation between the perturbed data at the scattered sites to compute the fit. The second method fits a polynomial surface model to the perturbed data using ordinary least squares regression analysis. For both fitting methods, the root mean square fit error is computed from the pointwise difference between the fit surface and the reference surface as the count and configuration of the sites is varied while also averaging the error across many different realizations of both the smooth variation of the reference exposure surface and the random, localized perturbations at the sample sites. Different site configurations are compared using this error statistic to make the recommendations noted above. Additionally, the two fitting approaches (interpolation vs linear regression) are compared based on the fit error observed in these simulations. These analyses, comparisons, and recommendations should inform future decisions on the noise monitor placement and the methods used to analyze the noise monitor data that is collected during X-59 community overflights.

sonic boom↗

Mean Winds and Tides over Urbana, Illinois During November 16-22, 1981

The Urbana Meteor Radar uses a high power pulse transmitter to achieve high echo rates, and an interferometer to spatially locate the individual echoes. The irregularly spaced observations of range, radial velocity, and direction cosines are reduced to a rectangular grid, evenly spaced in time and height, of estimates of the zonal and meridional wind. This is accomplished using the method of GROVES whereby a constant horizontal wind is fitted, using least squares, to all echoes occurring within a fixed time/height interval. This interpolation region is then stepped in time and height. the size of the interpolation region is 2 hours by 5 km, the time step is approximately 11 minutes, and the height step is 2 km. The filtering of high temporal and spatial frequencies is somewhat reduced by weighting the echoes according to their distance from the center of the interpolation box.

Tetenbaum, D.↗

Prediction of Unsteady Aerodynamic Coefficients at High Angles of Attack

The nonlinear indicial response method is used to model the unsteady aerodynamic coefficients in the low speed longitudinal oscillatory wind tunnel test data of the 0.1 scale model of the F-16XL aircraft. Exponential functions are used to approximate the deficiency function in the indicial response. Using one set of oscillatory wind tunnel data and parameter identification method, the unknown parameters in the exponential functions are estimated. The genetic algorithm is used as a least square minimizing algorithm. The assumed model structures and parameter estimates are validated by comparing the predictions with other sets of available oscillatory wind tunnel test data.

Pamadi, Bandu N.↗

Information Retrieval from SAGE II and MFRSR Multi-Spectral Extinction Measurements

Direct beam spectral extinction measurements of solar radiation contain important information on atmospheric composition in a form that is essentially free from multiple scattering contributions that otherwise tend to complicate the data analysis and information retrieval. Such direct beam extinction measurements are available from the solar occultation satellite-based measurements made by the Stratospheric and Aerosol Gas Experiment (SAGE II) instrument and by ground-based Multi-Filter Shadowband Radiometers (MFRSRs). The SAGE II data provide cross-sectional slices of the atmosphere twice per orbit at seven wavelengths between 385 and 1020 nm with approximately 1 km vertical resolution, while the MFRSR data provide atmospheric column measurements at six wavelengths between 415 and 940 nm but at one minute time intervals. We apply the same retrieval technique of simultaneous least-squares fit to the observed spectral extinctions to retrieve aerosol optical depth, effective radius and variance, and ozone, nitrogen dioxide, and water vapor amounts from the SAGE II and MFRSR measurements. The retrieval technique utilizes a physical model approach based on laboratory measurements of ozone and nitrogen dioxide extinction, line-by-line and numerical k-distribution calculations for water vapor absorption, and Mie scattering constraints on aerosol spectral extinction properties. The SAGE II measurements have the advantage of being self-calibrating in that deep space provides an effective zero point for the relative spectral extinctions. The MFRSR measurements require periodic clear-day Langley regression calibration events to maintain accurate knowledge of instrument calibration.

Lacis, Andrew A.↗

Molecular dynamics study of interstitial He clusters in nickel

This study presents a molecular dynamics analysis focusing on the behavior of interstitial helium (He) clusters in nickel (Ni), examining their formation, stability, and migration energetics. Consistent with previous research, we found that the binding energies of interstitial helium within a helium cluster are positive and increase with the cluster size, indicating a preference for helium atoms to cluster together. However, our findings also reveal that while the formation energy increases monotonically with cluster size, the increase in binding energy is non-monotonic. Importantly, small He clusters were observed to be thermally unstable at reactor operational temperatures (approximately 600 K), with the He 2 cluster exhibiting instability even at room temperature. With a binding energy of 0.49 eV for a He 4 cluster, we hypothesize that for helium bubbles to form via homogeneous nucleation (i.e., through trap mutation) at reactor operating temperatures, the helium concentration must be high enough to facilitate the formation of helium clusters of at least size 4 or larger. As expected, interstitial helium and small helium clusters are highly mobile. This mobility was observed not only at room temperature but also at temperatures as low as approximately 200 K. Furthermore, the mean squared displacement method has been utilized to determine the migration barriers and the corresponding prefactors for clusters ranging from He 1 to He 6

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Standardising the “Gregory method” for calculating equilibrium climate sensitivity

The equilibrium climate sensitivity (ECS) – the equilibrium global mean temperature response to a doubling of atmospheric CO 2 – is a high-profile metric for quantifying the Earth system's response to human-induced climate change. A widely applied approach to estimating the ECS is the “Gregory method” (Gregory et al., 2004), which uses an ordinary least squares (OLS) regression between the net radiative flux, N, and surface air temperature anomalies, ΔT, from a 150 year experiment in which atmospheric CO 2 concentrations are quadrupled. The ECS is determined by extrapolating the linear fit to N=0, i.e. the ΔT-intercept, indicating the point at which the system is back in equilibrium. This method has been used to compare ECS estimates across the CMIP5 and CMIP6 ensembles and will likely be a key diagnostic for CMIP7. Despite its widespread application, there is little consistency or transparency between studies in how the climate model data is processed prior to the regression, leading to potential discrepancies in ECS estimates. We identify 32 alternative data processing pathways, varying by differences in global mean weighting, net radiative flux variable, anomaly calculation method, and linear regression fit. Using 44 CMIP6 models, we systematically assess the impact of these choices on ECS estimates and calculate uncertainty ranges using two bootstrap approaches. While the inter-model ECS range is insensitive to the data processing pathway, individual outlier models exhibit notable differences. Approximating a model's native grid cell area (if irregular) with cosine of the latitude can decrease the ECS by 11 %, the choice of N-variable can change the ECS by 6 %, and some anomaly calculation methods can introduce spurious temporal correlations in the processed data. Beyond data processing choices, we also evaluate an alternative linear regression method – total least squares (TLS) – which has a more statistically robust basis than OLS. However, for consistency with previous literature, and given TLS may reduce the ECS compared to OLS (by up to 24 %), thereby making a known bias in the Gregory method worse, we do not feel there is sufficient clarity to recommend a transition to TLS in all cases. To improve reproducibility and comparability in future studies, we recommend a standardised Gregory method: weighting the global mean by cell area, using the top of the atmosphere (as opposed to the top of model) N-variable, and calculating anomalies by first applying a rolling average to the preindustrial control timeseries then subtracting from the raw CO 2 quadrupling experiment. This approach accounts for model drift while reducing noise in the data to best meet the pre-conditions of the linear regression. While CMIP6 results of the multi-model mean ECS appear insensitive to these processing choices, similar assumptions may not hold for CMIP7, underscoring the need for standardised data preparation in future climate sensitivity assessments.

Geosciences↗

Direct stellarator coil optimization for nested magnetic surfaces with precise quasi-symmetry

We present a robust optimization algorithm for the design of electromagnetic coils that generate vacuum magnetic fields with nested flux surfaces and precise quasi-symmetry. The method is based on a bilevel optimization problem, where the outer coil optimization is constrained by a set of inner least squares optimization problems whose solutions describe magnetic surfaces. The outer optimization objective targets coils that generate a field with nested magnetic surfaces and good quasi-symmetry. The inner optimization problems identify magnetic surfaces when they exist, and approximate surfaces in the presence of magnetic islands or chaos. We show that this formulation can be used to heal islands and chaos, thus producing coils that result in magnetic fields with precise quasi-symmetry. We show that the method can be initialized with coils from the traditional two-stage coil design process, as well as coils from a near-axis expansion optimization. We present a numerical example where island chains are healed and quasi-symmetry is optimized up to surfaces with aspect ratio 6. Another numerical example illustrates that the aspect ratio of nested flux surfaces with optimized quasi-symmetry can be decreased from 6 to approximately 4. In conclusion, the last example shows that our approach is robust and a cold-start using coils from a near-axis expansion optimization.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Optimizing GRACE/GRACE-FO Data and A priori Hydrological Knowledge for Improved Global Terrestial Water Storage Component Estimates

The comprehensive information of global terrestrial water storage (TWS) components (soil moisture, groundwater, snow, surface water) is essential for effective assessment of water resource availability, climate variation, and disaster mitigation measures. Observational data provided by the Gravity Recovery And Climate Experiment (GRACE) and GRACE Follow-On satellite missions offer global TWS variation (ΔTWS) in terms of an integrated water column. However, GRACE spatial resolution is relatively coarse (i.e., 3°), and the vertically integrated value cannot be separated into ΔTWS components directly. This study demonstrates the feasibility to estimate ΔTWS components at any desired spatial-vertical resolution by effectively maintaining the native resolution of the employed hydrological knowledge. It utilizes a least-squares with constraints (LSC) approach to rigorously incorporate GRACE and GRACE-FO data and a priori hydrological knowledge, with the aim to improve global ΔTWS components’ accuracy and spatial resolution. The 3°×3° GRACE mascon derived ΔTWS data is disaggregated into the 0.5°×0.5° anomalous soil moisture storage (ΔSMS), groundwater storage (ΔGWS), snow water equivalent (ΔSWE), and surface water storage (ΔSWS) based on the covariance information obtained from the Community Atmosphere Biosphere Land Exchange (CABLE) and the PCRaster Global Water Balance (PCR-GLOBWB) models. Evaluation with different ground measurements and satellite products between 2002 and 2019 exhibits significantly improved accuracy in all individual ΔTWS components. This improvement is of particular note in ΔGWS and ΔSWS, where the LSC approach increases the globally averaged correlation values by approximately 0.13 and 0.05, respectively. Reliable prior knowledge leads to a more accurate ΔTWS component estimate, and the use of ensemble-mean knowledge yields the best result.

GRACE↗

A storm of type 3 bursts observed by RAE-1 in August 1968

Curves of the number of type 3 bursts as a function of time are presented for six fixed frequencies (2.8, 1.65, 1.31, 0.995, 0.700, and 0.54 MHz). The curves peak at approximately 0500 UT August 20, 1968, and are symmetrical on both sides. Sakurai (1971) has shown that this time correlates well with the CMP of the McMath Region 9597. The maximum rate of bursts is approximately 150 per hour at the higher frequency of 2.8 MHz. Over 20,000 bursts were counted during the 15-day period from August 13 to August 27 when the active region was visible to the earth. A least-squares normal curve has been fitted to the observational data and calculations of variance and standard deviation are given.

Howard, E. G.↗

Progressive Response Surfaces

Response surface functions are often used as simple and inexpensive replacements for computationally expensive computer models that simulate the behavior of a complex system over some parameter space. Progressive response surfaces are ones that are built up progressively as global information is added from new sample points in the parameter space. As the response surfaces are globally upgraded based on new information, heuristic indications of the convergence of the response surface approximation to the exact (fitted) function can be inferred. Sampling points can be incrementally added in a structured fashion, or in an unstructured fashion. Whatever the approach, at least in early stages of sampling it is usually desirable to sample the entire parameter space uniformly. At later stages of sampling, depending on the nature of the quantity being resolved, it may be desirable to continue sampling uniformly over the entire parameter space (Progressive response surfaces), or to switch to a focusing/economizing strategy of preferentially sampling certain regions of the parameter space based on information gained in early stages of sampling (Adaptive response surfaces). Here we consider Progressive response surfaces where a balanced indication of global response over the parameter space is desired.We use a variant of Moving Least Squares to fit and interpolate structured and unstructured point sets over the parameter space. On a 2-D test problem we compare response surface accuracy for three incremental sampling methods: Progressive Lattice Sampling; Simple-Random Monte Carlo; and Halton Quasi-Monte-Carlo sequences. We are ultimately after a system for constructing efficiently upgradable response surface approximations with reliable error estimates.

Romero, V. J.↗