Results for “laser directionality” — Page 14

NASA NTRS2011

Using Innovative Technologies for Manufacturing Rocket Engine Hardware

Many of the manufacturing techniques that are currently used for rocket engine component production are traditional methods that have been proven through years of experience and historical precedence. As the United States enters into the next space age where new launch vehicles are being designed and propulsion systems are being improved upon, it is sometimes necessary to adopt innovative techniques for manufacturing hardware. With a heavy emphasis on cost reduction and improvements in manufacturing time, rapid manufacturing techniques such as Direct Metal Laser Sintering (DMLS) are being adopted and evaluated for their use on NASA s Space Launch System (SLS) upper stage engine, J-2X, with hopes of employing this technology on a wide variety of future projects. DMLS has the potential to significantly reduce the processing time and cost of engine hardware, while achieving desirable material properties by using a layered powder metal manufacturing process in order to produce complex part geometries. Marshall Space Flight Center (MSFC) has recently hot-fire tested a J-2X gas generator (GG) discharge duct that was manufactured using DMLS. The duct was inspected and proof tested prior to the hot-fire test. Using a workhorse gas generator (WHGG) test fixture at MSFC's East Test Area, the duct was subjected to extreme J-2X hot gas environments during 7 tests for a total of 537 seconds of hot-fire time. The duct underwent extensive post-test evaluation and showed no signs of degradation. DMLS manufacturing has proven to be a viable option for manufacturing rocket engine hardware, and further development and use of this manufacturing method is recommended.

Betts, E. M.↗

NASA NTRS2012

Piezocomposite Actuator Arrays for Correcting and Controlling Wavefront Error in Reflectors

Three reflectors have been developed and tested to assess the performance of a distributed network of piezocomposite actuators for correcting thermal deformations and total wave-front error. The primary testbed article is an active composite reflector, composed of a spherically curved panel with a graphite face sheet and aluminum honeycomb core composite, and then augmented with a network of 90 distributed piezoelectric composite actuators. The piezoelectric actuator system may be used for correcting as-built residual shape errors, and for controlling low-order, thermally-induced quasi-static distortions of the panel. In this study, thermally-induced surface deformations of 1 to 5 microns were deliberately introduced onto the reflector, then measured using a speckle holography interferometer system. The reflector surface figure was subsequently corrected to a tolerance of 50 nm using the actuators embedded in the reflector's back face sheet. Two additional test articles were constructed: a borosilicate at window at 150 mm diameter with 18 actuators bonded to the back surface; and a direct metal laser sintered reflector with spherical curvature, 230 mm diameter, and 12 actuators bonded to the back surface. In the case of the glass reflector, absolute measurements were performed with an interferometer and the absolute surface was corrected. These test articles were evaluated to determine their absolute surface control capabilities, as well as to assess a multiphysics modeling effort developed under this program for the prediction of active reflector response. This paper will describe the design, construction, and testing of active reflector systems under thermal loads, and subsequent correction of surface shape via distributed peizeoelctric actuation.

piezoelectric actuation↗

NASA NTRS2015

Computational Process Modeling for Additive Manufacturing (OSU)

Powder-Bed Additive Manufacturing (AM) through Direct Metal Laser Sintering (DMLS) or Selective Laser Melting (SLM) is being used by NASA and the Aerospace industry to "print" parts that traditionally are very complex, high cost, or long schedule lead items. The process spreads a thin layer of metal powder over a build platform, then melts the powder in a series of welds in a desired shape. The next layer of powder is applied, and the process is repeated until layer-by-layer, a very complex part can be built. This reduces cost and schedule by eliminating very complex tooling and processes traditionally used in aerospace component manufacturing. To use the process to print end-use items, NASA seeks to understand SLM material well enough to develop a method of qualifying parts for space flight operation. Traditionally, a new material process takes many years and high investment to generate statistical databases and experiential knowledge, but computational modeling can truncate the schedule and cost -many experiments can be run quickly in a model, which would take years and a high material cost to run empirically. This project seeks to optimize material build parameters with reduced time and cost through modeling.

Bagg, Stacey↗

NASA NTRS2016

Architecture for Mitigating Short-Term Warning Cosmic Threats: READI Project

Earth is being constantly bombarded by a large variety of celestial bodies and has been since its formation 4.5 billion years ago. Among those bodies, mainly asteroids and comets, there are those that have the potential to create large scale destruction upon impact. The only extinction-level impact recorded to date was 65 million years ago, during the era of dinosaurs. The probability of another extinction-level, or even city-killer, impact may be negligible, but the consequences can be severe for the biosphere and for our species. Therefore it is highly imperative for us to be prepared for such a devastating impact in the near future, especially since humanity is at the threshold of wielding technologies that allow us to do so. Majority of scientists, engineers, and policymakers have focused on long-term strategies and warning periods for Earth orbit crossing Near-Earth Objects (NEOs), and have suggested methods and policies to tackle such problems. However, less attention has been paid to short warning period NEO threats. Such NEOs test current technological and international cooperation capabilities in protecting ourselves, and can create unpredictable devastation ranging from local to global scale. The most recent example is the Chelyabinsk incident in Russia. This event has provided a wakeup call for space agencies and governments around the world towards establishing a Planetary Defense Program. The Roadmap for EArth Defense Initiative (READI) is a project by a team of international, intercultural, and interdisciplinary participants of the International Space University's Space Studies Program 2015 hosted by Ohio University, Athens, OH proposing a roadmap for space agencies, governments, and the general public to tackle NEOs with a short warning before impact. Taking READI as a baseline, this paper presents a technical description of methodologies proposed for detection and impact mitigation of a medium-sized comet (up to 800m across) with a short-warning period of two years on a collision course with Earth. The hypothetical comet is on a highly-inclined orbit having a high probability for Earth impact after its perihelion. For detection, we propose a space-based infrared detection system consisting of two satellites located at the Earth-Moon Lagrange points L1 and L2 coupled with space observatories, like the James Webb telescope and the Centennial telescope. These telescopes are supported by ground-based telescopes, like the Arecibo and Green Bank telescope, in the search for NEOs. Upon detection, the comet is tracked constantly using space- and ground-based telescopes. The deflection system is two-pronged, firstly involving the use of a high energy Directed Energy Laser Terminals (DELT) placed at Sun-Earth Lagrange points L4 and L5 so as to initiate and increase the ablation rate of the comet and deviate it from its collision trajectory, and secondly by the Hypervelocity Comet Intercept Vehicle (HCIV), a space-borne system combining a kinetic impactor with a thermonuclear device. The policy and international collaboration aspects to implement these methods are also outlined in the paper. The techniques mentioned could also be applied to mitigate medium-to-large sized asteroids (up to 2km across).

Laser Applications↗

NASA NTRS2016

An Assessment of Nondestructive Evaluation Capability for Complex Additive Manufacturing Aerospace Components

The primary focus of this work is to investigate some of the fundamental relationships between processing, mechanical testing, materials characterization, and NDE for additively manufactured (AM) components using the powder bed fusion direct melt laser sintered process. The goal is to understand the criticality of defects unique to the AM process and then how conventional nondestructive evaluation methods as well as some of the more non-traditional methods such as computed tomography, are effected by the AM material. Specific defects including cracking, porosity and partially/unfused powder will be addressed. Besides line-of-site NDE, as appropriate these inspection capabilities will be put into the context of complex AM geometries where hidden features obscure, or inhibit traditional NDE methods.

Walker, James↗

NASA NTRS2016

Applying Additive Manufacturing to a New Liquid Oxygen Turbopump Design

A liquid oxygen turbopump has been designed at Marshall Space Flight Center as part of the in-house, Advanced Manufacturing Demonstrator Engine (AMDE) project. Additive manufacturing, specifically direct metal laser sintering (DMLS) of Inconel 718, is used for 77% of the parts by mass. These parts include the impeller, turbine components, and housings. The near-net shape DMLS parts have been delivered and final machining is underway. Fabrication of the traditionally manufactured hardware is also proceeding. Testing in liquid oxygen is planned for Q2 of FY2017. This topic explores the design of the turbopump along with fabrication and material testing of the DMLS hardware.

O'Neal, Derek↗

NASA NTRS2016

Planetary Defense Architecture for Mitigating Short-Term Warning Cosmic Threats: READI Project

Earth is being constantly bombarded by a large variety of celestial bodies and has been since its formation 4.5 billion years ago. Among those bodies, mainly asteroids and comets, there are those that have the potential to create large scale destruction upon impact. The only extinction-level impact recorded to date was 65 million years ago, during the era of dinosaurs. The probability of another extinction-level, or even city-killer, impact may be negligible, but the consequences can be severe for the biosphere and for our species. Therefore it is highly imperative for us to be prepared for such a devastating impact in the near future, especially since humanity is at the threshold of wielding technologies that allow us to do so. Majority of scientists, engineers, and policymakers have focused on long-term strategies and warning periods for Earth orbit crossing Near-Earth Objects (NEOs), and have suggested methods and policies to tackle such problems. However, less attention has been paid to short warning period NEO threats. Such NEOs test current technological and international cooperation capabilities in protecting ourselves, and can create unpredictable devastation ranging from local to global scale. The most recent example is the Chelyabinsk incident in Russia. This event has provided a wakeup call for space agencies and governments around the world towards establishing a Planetary Defense Program. The Roadmap for EArth Defense Initiative (READI) is a project by a team of international, intercultural, and interdisciplinary participants of the International Space University's Space Studies Program 2015 hosted by Ohio University, Athens, OH proposing a roadmap for space agencies, governments, and the general public to tackle NEOs with a short warning before impact. Taking READI as a baseline, this paper presents a technical description of methodologies proposed for detection and impact mitigation of a medium-sized comet (up to 800m across) with a short-warning period of two years on a collision course with Earth. The hypothetical comet is on a highly-inclined orbit having a high probability for Earth impact after its perihelion. For detection, we propose a space-based infrared detection system consisting of two satellites located at the Earth-Moon Lagrange points L1 and L2 coupled with space observatories, like the James Webb telescope and the Centennial telescope. These telescopes are supported by ground-based telescopes, like the Arecibo and Green Bank telescope, in the search for NEOs. Upon detection, the comet is tracked constantly using space- and ground-based telescopes. The deflection system is two-pronged, firstly involving the use of a high energy Directed Energy Laser Terminals (DELT) placed at Sun-Earth Lagrange points L4 and L5 so as to initiate and increase the ablation rate of the comet and deviate it from its collision trajectory, and secondly by the Hypervelocity Comet Intercept Vehicle (HCIV), a space-borne system combining a kinetic impactor with a thermonuclear device. The policy and international collaboration aspects to implement these methods are also outlined in the paper. The techniques mentioned could also be applied to mitigate medium-to-large sized asteroids (up to 2km across).

Laser Applications↗

NASA NTRS2016

Applying Additive Manufacturing to a New Liquid Oxygen Turbopump Design

A liquid oxygen turbopump has been designed at Marshall Space Flight Center as part of the in-house, Advanced Manufacturing Demonstrator Engine (AMDE) project. Additive manufacturing, specifically direct metal laser sintering (DMLS) of Inconel 718, is used for 77% of the parts by mass. These parts include the impeller, turbine components, and housings. This paper discusses the impacts of the DMLS fabrication technique on the design of the turbopump and lessons learned during DMLS hardware fabrication and material testing.

O’Neal, T. Derek↗

NASA NTRS2017

High Density Packaging Technologies for RF Electronics in Small Spacecraft

This paper will describe a few high density packaging technologies which we are currently exploring for use in current and future small spacecraft applications. The three categories of technologies include organic multichip modules (MCMs), ceramic leadless surface mount technology (SMT) and 3D printed waveguide structures. There are many other packaging technologies that currently exist but these three were selected in part due to their long heritage in various commercial, military and space applications along with each having a relatively clear path to flight. For each of these technologies, detailed examples will be included in which hardware has been fabricated and tested for use in RF electronics for spacecraft transponders. The organic MCM example will be described in most detail and it utilizes a packaging technology by the name of CoreEZ which is a trademark of i3 Electronics. This MCM has shrunk a portion of our electronics down to 1/8th of its previous area. The CoreEZ technology has been shown to be rad hard beyond a total ionizing dose (TID) of 300kRad and the MCM which was fabricated has gone through thermal cycling and shown to have no degradation in performance. The ceramic leadless package examples include packages from high reliability manufactures by the name of KCB solutions and Barry Industries. In the case of KCB solutions, we have multiple products that will be described including a hermetic ceramic carrier which houses three microwave monolithic integrated circuits (MMICs) along with small discrete components. Finally, we will discuss the results of our search for a 3D printing process that allows us to reduce the cost and volume of our waveguide filters and diplexers for low cost small satellite applications. We have fabricated a few prototypes using direct metal laser sintering (DMLS) and metal coated plastics. Each of these packaging technology discussions will have a brief overview of its current and future use.

Aquirre, Fernando↗

NASA NTRS2019

Fabrication of Phononic-Isolated Kinetic Inductance Detectors

Kinetic inductance detectors (KID) have received increased interest due to their relative ease of fabrication, low noise, and scalability to large format arrays required by next generation of astronomical telescopes. The development of KIDs has progressed rapidly, with very low noise equivalent power demonstrated by several groups and KIDs arrays implemented in several ground-based and air-borne instruments. In this paper, we describe a new fabrication process which consists of a membrane isolated KID incorporating a phononic bandgap structure tuned to block recombination phonons from escaping to the thermal bath. This architecture is designed to increase the quasi-particle lifetime and results in increased responsivity to signal photons and lower noise. These devices have been fabricated as lumped-element resonators with hafnium inductors and Nb capacitors on low stress silicon nitride and silicon-on-insulator membranes. We discuss the fabrication process, which uses a combination of sub-micron laser based direct write lithography and nanoscale electron beam lithography.

Denis, Kevin L.↗

NASA NTRS2019

Using Computational Flow Imaging to Optimize Filtered Rayleigh Scattering Measurements of an Isolator Shock Train

Filtered Rayleigh scattering (FRS) is a laser diagnostic where the intensity of elastically scattered light is measured after it passes through a molecular absorption filter. The filter removes background interference that overwhelms the relatively weak scattering from the gas molecules. However, with a filter, the measured light intensity depends on many of the scattering gas properties, including pressure, density, temperature, and velocity. In this work, CFD simulations of an isolator shock train flow field are input into a physics-based model to predict the values of FRS intensity measurements in a proposed experiment. The goal is to evaluate if a simplistic FRS setup (that utilizes one camera, laser, and absorption filter) can be used to accurately quantify number density despite the fact that the scattered light intensity also depends on other gas properties. It is found that the experimental setup can be optimized such that a linear relationship describes the number density with an average prediction error of 2%. The vast majority of the flow exhibits prediction errors of less than 3%, but small regions of the flow reach up to 11% error. A sensitivity analysis shows that the prediction error increases with the central wavelength of the incident laser light and decreases with the angle between the camera and laser propagation directions. The optimal experimental parameters are chosen based on a compromise between the prediction error, spatial resolution, and the amount of unfiltered light. In the future, the proposed FRS setup will be implemented to acquire new and valuable information on an isolator shock train, a flow field that has been traditionally studied using wall static pressure measurements and path-integrated visualization techniques, such as schlieren and shadowgraphy.

Hunt, Robin L.↗

NASA NTRSDate not supplied

Metal Fused Filament Fabrication of Titanium Alloy for In Space Manufacturing

NASA is developing materials and processes for the in-space manufacturing of many items for the International Space Station (ISS) and future exploration platforms. These new manufacturing processes will require the further development of current 3D printing processes to achieve high-performance metal parts within the power and space constraints of the ISS. Manufacturing Ti-6Al-4V alloy parts with 3D printing using a metal fused filament fabrication (MF3) process is an alternative process to the Direct Metal Laser Sintering (DMLS) of the metal powders additive manufacturing process. Our initial work fabricating Ti-6Al-4V parts from Ti-6Al-4V powder-binder feedstock and processed with the MF3 process has resulted in 95-97% sintered densities. The current development work of optimized sintered properties investigates the effects of variation in sintering time, temperature, and vacuum on the sintered properties of Ti-6Al-4V MF3 printed tensile bars. Sintered properties such as density, hardness, and tensile properties were characterized followed by microstructural and chemical (O/C/N) analysis to understand the role of sintering process on the ensuing material properties. Future development of the MF3 process will also involve investigation of the effects of micro-milling the Ti-64Al-4V powder to nanometer particle sizes and the investigation of laser sintering of the 3D printed devices. This new micro-milling technique will have broad application to other areas that require particle size reduction of hard metallic materials, such as Nuclear Thermal Propulsion and other NASA technologies. Laser sintering in lieu of high temperature thermal sintering should allow for significant power reduction and improved processing speeds.

sintering, alloys, 3D printing↗

NASA NTRS2016

High Density Packaging Technologies for RF Electronics in Small Spacecraft

This paper will describe a few high density packaging technologies which we are currently exploring for use in current and future small spacecraft applications. The three categories of technologies include organic multichip modules (MCMs), ceramic leadless surface mount technology (SMT) and 3D printed waveguide structures. There are many other packaging technologies that currently exist but these three were selected in part due to their long heritage in various commercial, military and space applications along with each having a relatively clear path to flight. For each of these technologies, detailed examples will be included in which hardware has been fabricated and tested for use in RF electronics for spacecraft transponders. The organic MCM example will be described in most detail and it utilizes a packaging technology by the name of CoreEZ which is a trademark of i3 Electronics. This MCM has shrunk a portion of our electronics down to 1/8th of its previous area. The CoreEZ technology has been shown to be rad hard beyond a total ionizing dose (TID) of 300kRad and the MCM which was fabricated has gone through thermal cycling and shown to have no degradation in performance. The ceramic leadless package examples include packages from high reliability manufactures by the name of KCB solutions and Barry Industries. In the case of KCB solutions, we have multiple products that will be described including a hermetic ceramic carrier which houses three microwave monolithic integrated circuits (MMICs) along with small discrete components. Finally, we will discuss the results of our search for a 3D printing process that allows us to reduce the cost and volume of our waveguide filters and diplexers for low cost small satellite applications. We have fabricated a few prototypes using direct metal laser sintering (DMLS) and metal coated plastics. Each of these packaging technology discussions will have a brief overview of its current and future use.

Schatzel, Donald↗

NASA NTRSDate not supplied

Advancing GRCop-based Bimetallic Additive Manufacturing to Optimize Component Design and Applications for Liquid Rocket Engines

Additive manufacturing (AM) is advancing many applications of component design for liquid rocket engines. The ability to rapidly design and manufacture components has provided significant opportunities for development and flight programs across the propulsion industry. AM has demonstrated significant advantages that include cost and schedule savings in addition to performance improvements through new design opportunities. While these performance advantages can be in the characteristics of complex design features, they can also be in the form of new materials. AM has been demonstrated in these various component applications using a variety of metal alloys, many of which are traditional alloys for extreme environments. Additional developments were completed using AM to provide new alloys and maturing these material uses for high performance applications. Almost all of the prior developments across component applications have focused on single-alloys in these AM processes. NASA and industry partners have focused in recent years to advance processing to create bimetallic and multicomponent AM processes and materials. The role of multi-alloy AM offers advantages since it can further optimize weight, optimize reliability and performance by increasing the strength to weight ratio of a component, and can optimize materials for various engineering requirements. This is particularly important in liquid rocket engine combustion devices that must reject heat in high heat flux environments yet maintain adequate structural margins under high operational pressure. NASA has been exploring several AM processes, materials, and applications for combustion devices, specifically combustion chambers, injectors, nozzles, and ignition systems. These components require fine geometric features for internal flow or cooling functionality. They experience high thermal gradients across thin-walls and must survive high pressures and temperatures from propellants and the combustion process. A copper-based alloy is normally used to provide high thermal conductivity, but at the detriment of increased weight if used as a single alloy in an AM chamber. Various AM processes were demonstrated on these components using a copper-based alloy/superalloy bimetallic solution. The AM processes being explored individually and in combination for bimetallic applications include Laser Powder Bed Fusion (L-PBF), Laser Powder Directed Energy Deposition (LP-DED), and cold spray. The combination of bimetallic material combinations explored in this research include copper-based material primarily and superalloys, Inconel 625 or NASA HR-1. The various aspects of the additive manufacturing processes and challenges, materials characterization, and the testing of bimetallic components in a relevant environment will be discussed.

Additive Manufacturing↗

NASA NTRSDate not supplied

Advancing GRCop-based Bimetallic Additive Manufacturing to Optimize Component Design and Applications for Liquid Rocket Engines

Additive manufacturing (AM) is advancing many applications of component design for liquid rocket engines. The ability to rapidly design and manufacture components has provided significant opportunities for development and flight programs across the propulsion industry. AM has demonstrated significant advantages that include cost and schedule savings in addition to performance improvements through new design opportunities. While these performance advantages can be in the characteristics of complex design features, they can also be in the form of new materials. AM has been demonstrated in these various component applications using a variety of metal alloys, many of which are traditional alloys for extreme environments. Additional developments were completed using AM to provide new alloys and maturing these material uses for high performance applications. Almost all of the prior developments across component applications have focused on single-alloys in these AM processes. NASA and industry partners have focused in recent years to advance processing to create bimetallic and multicomponent AM processes and materials. The role of multi-alloy AM offers advantages since it can further optimize weight, optimize reliability and performance by increasing the strength to weight ratio of a component, and can optimize materials for various engineering requirements. This is particularly important in liquid rocket engine combustion devices that must reject heat in high heat flux environments yet maintain adequate structural margins under high operational pressure. NASA has been exploring several AM processes, materials, and applications for combustion devices, specifically combustion chambers, injectors, nozzles, and ignition systems. These components require fine geometric features for internal flow or cooling functionality. They experience high thermal gradients across thin-walls and must survive high pressures and temperatures from propellants and the combustion process. A copper-based alloy is normally used to provide high thermal conductivity, but at the detriment of increased weight if used as a single alloy in an AM chamber. Various AM processes were demonstrated on these components using a copper-based alloy/superalloy bimetallic solution. The AM processes being explored individually and in combination for bimetallic applications include Laser Powder Bed Fusion (L-PBF), Laser Powder Directed Energy Deposition (LP-DED), and cold spray. The combination of bimetallic material combinations explored in this research include copper-based material primarily and superalloys, Inconel 625 or NASA HR-1. The various aspects of the additive manufacturing processes and challenges, materials characterization, and the testing of bimetallic components in a relevant environment will be discussed.

Additive Manufacturing↗

NASA NTRSDate not supplied

Advancement of Novel Additively Manufactured Alloys for Space Applications

NASA has been involved in the development and maturation of metal additive manufacturing (AM) for space applications since the late 2000’s. Several efforts have focused on the understanding of AM processes through material characterization and testing, standards development, component fabrication, and infusion into development and flight applications. While many common aerospace alloys have been and continue to be a focus of ongoing development, the need for custom-alloy developments for high performance applications enabled by AM processes has been realized. The applications being targeted are liquid rocket engines with high heat fluxes, high pressure, and that utilize propellants such as hydrogen, which can degrade the alloy. NASA has recently focused on the development and advancement of novel alloy advancement using AM for use in these harsh environments, such as GRCop-42, GRCop-84, NASA HR-1, and JBK-75. These alloys have been evaluated using the laser powder bed fusion (L-PBF) and laser powder directed energy deposition (LP-DED) processes. The results from these processes have demonstrated that AM can enable rapid development of new alloy systems that can yield higher performances. These alloys have undergone the fundamental metallurgical evaluations, heat treatment study, and microstructure characterization and mechanical testing campaign. This, combined with direct application-specific component fabrication and hot-fire testing, enabled the increase of the Technology Readiness Level (TRL). This presentation will provide a background and overview of these AM-enabled novel alloys, AM processing development including metallurgical and mechanical property studies. It will also cover the latest advancement in the parallel component development and testing and future developments. The goal of these alloy development is to allow for technology infusion into NASA and commercial spaceflight missions as well as to establish and sustain the needed commercial AM supply chain.

Additive Manufacturing↗

NASA NTRSDate not supplied

Advancement of Extreme Environment Additively Manufactured Alloys for Next Generation Space Propulsion Applications

The National Aeronautics and Space Administration (NASA) has been involved in the development and maturation of metal additive manufacturing (AM) for space applications since the late 2000’s. Several efforts focused on the understanding of AM processes through material characterization and testing, standards development, component fabrication, and infusion into propulsion development and flight applications. NASA matured commonly used aerospace alloys from various alloy families (Nickel, Copper, Stainless and Steel, Aluminum, and Titanium-based) through detailed AM process and heat treatment characterization, in addition to mechanical and thermophysical testing. While these alloys are actively used in many propulsion applications, there is a need for ongoing AM optimized alloys using integrated computational materials engineering (ICME) and process development for high performance applications. The applications targeted are liquid rocket engines; advanced propulsion systems; and in-space propulsion with high heat fluxes, high pressure, and/or that use propellants that can degrade alloys (e.g., hydrogen). This paper highlights the characterization and physical properties of the more common AM alloys using laser powder bed fusion (L-PBF) and laser powder directed energy deposition (LP-DED) processes. Additionally, this paper discusses some of the ongoing novel alloy development and maturation using AM for use in these harsh environments, such as GRCop-42, GRCop-84, NASA HR-1, GRX-810, and C-103. The results from these processes demonstrated that AM could enable rapid development and ongoing efforts for optimized alloys using ICME, yielding higher performances. These alloys have undergone modeling, fundamental metallurgical evaluations, heat treatment studies, detailed microstructure characterization, and mechanical testing campaigns. This, combined with direct application-specific component fabrication and hot-fire testing, enabled the increase of the Technology Readiness Level (TRL) through high duty-cycle testing. A background and overview of these novel AM-enabled alloys and AM processing developments including metallurgical and mechanical property studies is presented here. The latest advancement in the parallel component development and hot-fire testing and future developments for these alloys is also discussed.

Additive Manufacturing↗

NASA NTRSDate not supplied

Maturation of Additive Manufactured Aerospace Alloys and Development of Mechanical and Thermophysical Properties for Space Applications

The National Aeronautics and Space Administration (NASA) has been involved in the development and maturation of metal additive manufacturing (AM) for space applications since the late 2000’s. Several efforts have focused on the understanding of AM processes through design optimization, component fabrication, material characterization, testing, standards development, and infusion into propulsion development for flight applications. NASA and partners have matured commonly used aerospace alloys from various alloy families (Nickel, Steel, Iron, Aluminum, and Titanium) and AM processes. An extensive effort has been ongoing between NASA, industry partners, and academia to complete detailed AM process and heat treatment characterization, in addition to generating temperature-dependent mechanical and thermophysical properties. This presentation highlights the characterization and property results using laser powder bed fusion (L-PBF) and laser powder directed energy deposition (LP-DED) processes among various alloys. In addition to commonly used alloys, there is a need for ongoing AM optimized alloys using integrated computational materials engineering (ICME) and process development for high performance applications. The applications targeted are launch vehicles, liquid rocket engines, advanced propulsion systems, advanced power systems, and in-space propulsion with high heat fluxes, high pressure, and that utilize propellants such as hydrogen, which can degrade alloys. This presentation will also discuss some of the ongoing novel alloy development and maturation using AM for use in these harsh environments, such as GRCop-42, GRCop-84, NASA HR-1, and C-103. The results from these processes have demonstrated that AM can enable rapid development and new AM optimized alloys can yield higher performance. These alloys have undergone modeling, fundamental metallurgical evaluations, heat treatment studies, and microstructure characterization and mechanical testing campaigns. This, combined with direct application-specific component fabrication and hot-fire testing, can enable the increase of the Technology Readiness Level (TRL) through high duty-cycle testing. This presentation provides a background and overview of these various common and AM-enabled alloys and processing developments including the initial effort related to metallurgical, mechanical, and thermophysical property studies. It also covers the latest advancement in the parallel component development, hot-fire testing, and future developments for these alloys.

Additive Manufacturing↗