Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “integrated circuit modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

237 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Low-Temperature Plasma Treatment for Enhanced Recovery of Highly Valued Critical REEs from Coal (Final Report)

The principle objective of this project was to develop a novel process flowsheet using low-temperature plasma treatment (LTP) integrated with conventional hydrometallurgical processes to recover rare earth elements (REEs), especially highly valued REEs (i.e. scandium and critical REEs), from coal and coal byproducts. LTP treatment was used to pretreat the solid feed material prior to leaching in an effort to improve the leaching characteristics of the REEs and potentially reduce acid consumption. Initially, a detailed experimental program was performed on a laboratory LTP furnace to identify a set of process parameter values to be used for assessing the enhanced leaching performance achieved on four specific gravity fractions of West Kentucky No. 13 and Fire Clay coarse coal refuse materials. High-temperature oxidation (HTO)) was also evaluated as a means for improving REE leachability on the same fractions of both coal sources. The lixiviants used to assess leachability improvements included: i) untreated water, ii) 0.1 M ammonium sulfate solution and iii) 1.2 M sulfuric acid solution at a temperature of 75°C. The laboratory data was used to develop multiple process flow sheets using HTO only to produce a rare earth oxide mix concentrate or utilizing both LTP and HTO treatment processes to generate a high purity heavy REO mix concentrate and a light REO mix concentrate. A techno-economic analysis was performed on each circuit. Low-temperature plasma oxidation was found to enhance REE leaching characteristics for all specific gravity (SG) fractions of the West Kentucky No. 13 coarse refuse material. The leaching recovery improvement was preferentially achieved for the heavy REEs with higher values obtained when treating the lower density fraction material. For example, the leaching recovery for the heavy REEs in the untreated 1.6 SG Float fraction material was 8% in a 0.1 M ammonium sulfate solution. After LTP treatment for 32 hours, heavy REE recovery increased to 33%. The corresponding recovery value for the light REEs was 10%. These findings indicate a strong affinity of the heavy REEs with the organic material, which is the component being reduced in content during the LTP treatment. Scanning electron micrographs showed the development of a honeycomb structure with increased LTP treatment with higher surface area as confirmed from BET measurements. Higher surface area promotes improved leaching efficiency due to enhance chemical interactions. When using 1.2 M sulfuric acid, the LTP treatment was found to provide a heavy REE recovery increase from 23% to 53% for the 1.6 SG Float fraction which corresponded to an ash content increase from around 20% to 35%. However, LTP treatment provided no improvement in leaching characteristic for the 2.2 SG sink material in the acid solution, which was likely due to the low organic content. The LTP treatment of the Fire Clay SG fractions provided no improvement in REE leaching characteristic, which may be due to the association with REE minerals such as monazite and REE-associated mineral matter such as clays. High temperature oxidation using temperatures in the range of 600-750OC was found to significantly enhance the leaching characteristics of both the light and heavy REEs for all density fractions in both coarse coal refuse materials. Generally, the increase in light REE recovery for the West Kentucky material was from 15% for the untreated material to 90% for the HTO treated material at 600°C. Recovery values dropped significantly when using temperatures below 600°C and above 750°C. The impact of the excessive temperatures was most likely a result of sintering. For the heavy REEs, HTO significantly improved recovery in the lighter SG fractions, which may be due to an affinity with the organic content. Only limited heavy REE recovery improvement was obtained for the denser SG fractions. Another benefit of HTO is the conversion of calcium-based minerals to a very soluble calcium oxide, which is removable using a mild acid solution, and the conversion of Fe minerals to relatively insoluble minerals such as hematite and magnetite. The pregnant leaching solution produced from the leaching of all SG fractions obtained from both coal sources was treated using two stages of solvent extraction procedurally modeling a rougher-cleaner circuit followed by oxalic acid precipitation. Rare earth oxide products having a purity greater than 97% was produced from nearly all of the SG fractions. A novel process flowsheet was developed based on the selective leaching of heavy REEs that was made possible through LTP treatment of West Kentucky No. 13 coarse refuse followed by salt leaching. In the flowsheet, coal refuse material is ground to a top size of 1mm and then treated by LTP. The treated material is mixed into a 0.1 M ammonium sulfate solution and then filtered to produce a heavy REE enriched pregnant leach solution. The heavy REEs are concentrated by two stages of selective precipitation to produce a heavy REE mix oxalate and then roasted to obtain a heavy REO mix concentrate. The solid residues remaining after salt leaching is dried and then subjected to HTO treatment followed by concentration using selective precipitation and roasting to produce a light REO mix concentrate. An alternative circuit was developed using HTO treatment only to treat 100% of the coarse refuse material followed by selective precipitation and roasting to generate a high purity REO mix product. A techno-economic analysis performed for the treatment of West Kentucky No. 13 and Fire Clay coarse refuse based on a hypothetical 500-tph plant revealed that the net present value for all scenarios was significantly negative. Primary reasons include: i) a substantial decrease in the basket value of the final product relative to the feed and ii) high chemical costs relative to the amount of product generated. The basket value reduction was primarily due to little to no scandium recovery due to poor leaching characteristics when using low acid concentrations as necessitated by the low feed grades. Operating costs were primarily influenced by the chemical costs relative to the kilograms of concentrate produced and feed grade. For the Fire Clay coarse refuse material, the total operating cost was estimated to be $354 per kg of REO produced which was higher than the basket value of the REO product ($276/kg). Approximately 37% of the total cost was the sulfuric acid used during the leaching process. A comparative analysis performed to assess the economic viability of using low-temperature plasma furnaces found that market value enhancement for the generation of both heavy REO and light REO concentrates will be needed in addition to significant technology advancements to reduce the cost of plasma furnaces.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2021

Development of NDE/NDT Tools for High-Volume & High-Speed Inspection of CFRP Structures in Automotive Manufacturing

Main advantages of the air-coupled ultrasound testing (ACUT) and electromagnetic testing (EMT) techniques for NDE of CFRP composites were non-contact sensing, scalability for high-speed inspection, cost-effectiveness, and non-hazardous operation. Despite these advantages, no systems that would satisfy the project requirements were commercially available. Hence, one of the major efforts of the Michigan State University (MSU) team at the initial stage of the project was to close this technological gap by developing, optimizing, and validating array sensors that would provide sufficient sensitivity, spatial coverage, and resolution for robust defect detection. Optimization of the ACUT and EMT sensor designs was performed using experimentally validated finite element models. Initial experiments using array probes were conducted on relatively flat CFRP samples. In parallel, the MSU team designed and assembled a portable platform with two robotic arms. The robots were equipped with newly designed sensors that enabled high-speed NDE of curved CFRP parts. Presently, the developed robotic platform can be used as a demo/template NDE system, which is easily adaptable to manufacturing environments and in-line NDE. The ACUT NDE system developed by the MSU team used a high-power 4-channel pulser receiver for parallel data acquisition. The array probes were designed by stacking commercially available ACUT transducers, which operated in the frequency range between 100 kHz and 500 kHz. MSU optimized the excitation procedure and developed wave focusing cones so as to reduce the crosstalk between the transducers and to provide higher pulse repletion frequency (PRF). The through-transmission (TT) and single-side access (SSA) inspection modes were successfully implemented. In the TT-ACUT, structural defects in CFRP were detected by passing ultrasonic waves through the test part. Hence, the ACUT transmitters and receivers needed to be placed on the opposite sides of the test part. In the SSA-ACUT, guided waves (GW) were excited in the test part using the transmitters and were sensed by the receivers from the same side. Multi-channel TT-ACUT and SSA-ACUT provided high-speed NDE, and were successfully validated on CFRP test samples with interlaminar delaminations and other embedded defects The EM techniques developed by the MSU team included: 1) eddy current testing (ECT), 2) capacitive imaging (CI) and hybrid dual-mode imaging. In ECT, structural damage was detected in CFRP using coils sensor arrays. In ECT, the excitation magnetic field is generated by passing an alternating current through a coil, which is placed above the test sample. The excitation field penetrates the conductive sample and induces the eddy currents in its transect. In turn, the eddy currents generate the reaction field, which affects the total field sensed by a coil. Hence, the presence of structural flaws will alter the eddy current flow and the picked-up signal. ECT is mostly sensitive to local changes of the electric conductivity of the test sample, and CFRPs are mostly conductive in the direction of carbon fibers. Hence, ECT was well suited for the detection of fiber damage/fiber irregularities. The MSU team developed printed circuit boards (PCB) with coil sensor arrays optimized for NDE of CFRP. Unlike most commercial probes designed for ECT of metallic structures, the MSU array probes were designed for operation in [1-10] MHz frequency range, which was optimal for low-conductive CFRP. Multiple sensing topologies (coil groups excitation/sensing arrangements) were implemented and successfully validated. Capacitive Imaging (CI) technique developed by MSU was complementary to ECT. In contrast to ECT, which was sensitive to local changes of the electrical conductivity, the CI was sensitive to local changes of the dielectric constant. Therefore, CI could provide information about matrix damage/matrix irregularities in CFRP. The MSU CI sensor arrays were made of multiple circular or rectangular open-plate capacitors printed on PCB. Sensors of this type are not commercially available. In addition to ECT and CI, the MSU team developed a hybrid (dual-mode) inductive/capacitive measurement technique that synergistically combined the benefits of inductive and capacitive sensing for rapid NDE of fiber reinforced polymer (FRP) composite structures. Fiber damage and fiber irregularities in FRPs were detected by configuring hybrid sensors as coil sensors. Similarly, matrix damage, matrix irregularities and interlaminar delaminations were detected by configuring hybrid sensors as capacitive sensors. ECT and CI were performed sequentially by means of electronic switching. Hence, eliminating the need for mounting two separate sensor arrays on the probe. Portable robotic platform was developed by MSU for multi-technique high-speed NDE of CFRP test parts. The platform had two 6-axis robots, which enabled inspection of curved parts in approximately a 6×6×6 ft 3 active scan area. On the software side, the MSU team integrated scripts for NDE hardware control with scripts for robot motion control. MSU also implemented automated path planning for the robots, reconstruction of part’s surfaces via stereovision, 3D rendering of inspection data, and image processing algorithms for enhanced defect detection. Automotive composite parts manufactured by Plasan Composites from Phase I were used to validate the ACUT and EMT techniques on representative testbeds. Among those parts were three X-braces for a Dodge Viper, one composite calibration plaque with known defects at known locations, and four other test sections, including sections from a front splitter, a corner section from a composite hood, and a high-pressure RTM panel made using non crimp fabric. Other test samples included CFRP and GFRP calibration plates with fiber/matrix defects fabricated at MSU/CVRC.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Pilot-Scale Testing of an Integrated Circuit for the Extraction of Rare Earth Minerals and Elements from Coal and Coal Byproducts Using Advanced Separation Technologies

The primary objective of this project was to develop and demonstrate an integrated pilot-scale circuitry for recovering high-value rare earth elements (REEs) from coal and coal byproducts. The target performance was to produce a mixed REE product with content of at least two percent by weight on a dry mass basis in a cost-effective and environmentally benign manner. During the first nine months of the project period (Phase 2 Budget Period 2), pilot plant construction was completed including all field site startup activities such as permitting, engineering design, procurement/bidding, unit fabrication, site construction, equipment installation, module assembly, safety training, and circuit shakedown. During the remaining 21 months of project period (Phase 2 Budget Period 3), detailed field-testing activities were performed including feedstock sample collection and preparation, exploratory testing, circuit modification, detailed parametric study, and performance optimization. A detailed techno-economic analysis was performed based on the pilot plant testing findings which provided various scenarios for REE production. The project successfully accomplished the proposed target performance by producing mixed rare earth oxide (REO) with greater than 90% purity by weight in a continuous pilot scale operation from two distinctly different coarse refuse materials (i.e., West Kentucky No. 13 and Fire Clay coal seams), and at least three secondary sources (i.e., heap leach process and naturally formed acid mine drainage system). Project partners included the University of Kentucky, Virginia Tech, West Virginia University, Alliance Coal, Blackhawk Mining, Mineral Refining Company, and Mineral Separation Technologies. The pilot scale test facility was constructed at a former mining complex owned by Alliance Natural Resource Partners (Alliance Coal). The site was rehabilitated to accommodate the equipment installation, construction and fabrication, electrical power requirement, water line management and containment. The process units constructed and installed included X-ray sorting unit, crushing and grinding unit, physical separation unit, acid leaching unit, solvent extraction unit, and wastewater management unit. A rare earth mineral concentration unit was constructed as a standalone unit for flexible operation. A detailed environmental assessment and control plan was carried out to identify and quantify any potential impacts of the pilot-scale processing circuitry on the human and eco-system health and well-being. Corresponding mitigation strategies and control measures were provided. A conceptual flowsheet was developed to effectively remove thorium and uranium from high purity rare earth oxide mix or any potential radionuclide enriched stream. The two distinct feedstock materials were secured from the Blackhawk Mining Complex in eastern Kentucky where the Fire Clay (Hazard No. 4) seam is processed. The West Kentucky No. 13 (Baker) coarse refuse material was collected from an active process stream at an Alliance coal preparation plant located in western Kentucky. Characterization analysis indicated that both of feed materials generated from the two sources contained >300 ppm of TREEs on a dry whole mass basis which met the requirements for a qualified feed stock. The two feedstocks were further upgraded using a dual x-ray sorter to prepare the feed material for hydrometallurgical circuit. Thermal treatment on feed material prior to leaching was found to: 1) improve the leaching recovery of REEs, 2) increase the leaching kinetics, and 3) allow the leaching reaction to occur at lower acidity. Roasting at 600°C was selected as the pre-treatment condition for both West Kentucky No. 13 and Fire Clay coarse refuse material. Over 40% of leaching recovery was achieved by roasting West Kentucky No. 13 material having a top particle size of 3 mm in the pilot scale operation using 1.2M sulfuric acid leaching at 75OC. Initial pilot scale testing involved continuous operation of the pilot plant for 94 hours. The leaching unit was operated at solid-to-liquid ratio of 1 to 10 (w/v) using 0.5M sulfuric acid solution at a temperature of 75°C. The continuous solvent extraction circuit utilized rougher and cleaner units with DEHPA and TBP as the extractants. An innovative stripping circuit was developed to accumulate the REE concentration in the stripping solution to a level above 600 ppm. A bleed stream from the recycled strip solution was treated using oxalic acid precipitation which produced a high grade rare earth oxalate. The oxalate product was roasted to remove the oxalate which produced a rare earth oxide product having a purity greater 90%. Due to high concentrations of contaminant ions in the pregnant leach solution (PLS), a modified flowsheet was developed that involved pre-concentration of the REEs using multiple stages of precipitation and redissolution. The advantage of this process was improved removal of contamination before the downstream purification process and a significant cost reduction relative to the circuit that utilized the solvent extraction process. The modified circuitry included processes involving leaching, multistage precipitation, redissolution, and oxalate precipitation followed by roasting of the oxalate product. The circuit produced a mixed REO that was 92.96% pure from the initial test. A detailed parametric test plan was carried out which involved varying key parameters including solids feed rate, acid flowrate, acid concentration, multistage precipitation pH, redissolution pH, oxalate precipitation dosage and pH. The response variables included REE recovery, contaminant recovery, REO product grade and overall chemical consumption. Test results indicated that the acid-to-solid ratio is the key parameter to leaching efficiency as performance deteriorated with an increase in solids concentration. The optimal pH determined for REE precipitation and redissolution was 6.5 and 2.5, respectively. Additional tests were conducted to further improve the flowsheet. Recirculating a portion of the PLS to the feed of the leach tanks improved the leaching performance by lowering the pH of the leaching system and reducing the contamination recovery by shortening the residence time. Moreover, the removal of Al prior to REE precipitation significantly reduced the oxalic acid consumption in the oxalate precipitation circuit. The modified circuit produced over 90% grade REO by weight from both West Kentucky No. 13 and Fire Clay coarse refuse material in pilot scale continuous test programs. A case analysis model was developed to project the REE and major contaminants concentration in each PLS stream based on the leaching condition, pH cut point, and oxalic acid dosage. A correlation was established using empirical and semi-empirical models. Using the models, chemical consumption required for each stage was predicted based on the projected performance of the hydrometallurgy circuit. After identifying the optimum conditions, validation tests were carried out for the treatment of both West Kentucky No. 13 and Fire Clay coarse refuse materials in the pilot plant. The actual circuit performance and chemical consumptions were very close to the model predictions. Other than the two coarse refuse sources, several secondary feedstocks were also tested in the pilot plant facility. A “heap leach” system was constructed using the coarse refuse material generated from cleaning the West Kentucky No. 13 seam coal. Using the two stage SX rougher and cleaner circuit, a concentrate with a grade >90% REO was produced while recovering >97% of the REEs from the heap leach PLS. Naturally generated acid mine drainage (AMD) from West Kentucky No.13 mine was processed using the multistage precipitation circuit in the pilot plant in a test conducted for a period of 32 hours. The final grade of the mix RE oxide produced from the AMD was 90.84% with an overall circuit recovery of 64%. The primary source of REE was the selective precipitation steps involving iron and aluminum rejection. The hydrophobic-hydrophilic separation (HHS) process was proven to effectively recover coal from fine waste materials. For REM recovery, the HHS process was able to produce concentrates at grades of approximately 1.8% REE on an ash basis; however, recovery values were typically low, <10%, under the optimal conditions determined in the laboratory-scale testing. Staged testing of the pilot-scale HHS process for coal recovery and semi-continuous laboratory testing for REM testing showed that a total concentration ratio of more than 15x was observed for the REM recovery process. A circuit simulation package was developed for REE extraction and purification using a spreadsheet-based platform (Microsoft Excel). The REESim circuit simulation package is configured to track the mass and volume flows of components passing through a series of unit operations specified and configured by the user. The mass rates can then be utilized by the user to determine important performance indicators such as product mass yields, concentrate purity levels, element-by-element recoveries, and so forth. The techno-economic analysis showed that the roasting and leaching operations were the most expensive capital items, each contributing approximately 30% to the total capital cost. One notable contributor to the high production costs was the low REE recovery observed in the pilot scale trials. The product basket price was shown to have a strong influence on the economic viability of the scenarios, with the scandium price being the most significant influencer. Operating cost was shown to be extremely sensitive to REE recovery, REE feed grade, and leaching acid consumption. An analysis of ten different scenarios for a 500 t/h commercial operation revealed that three were economically favorable, producing internal rates of return varying from 27.7% to 33.1% and payback periods of 4 to 5 years. The project successfully developed and demonstrated a process to recover REEs from coal and coal byproducts in a pilot-plant operation which consistently produced over 90% grade REO mix from varies types of feedstocks. Commercialization analysis showed that the technology readiness level successfully achieved TRL 6 at the end of the project and demonstrated the need and the potential for scaling the process to further advance the technologies toward the goal of providing a domestic supply of REEs at a commercial scale.

01 COAL, LIGNITE, AND PEAT↗