Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “hot plasma”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

A High Specific Output Gasoline Low Temperature Combustion Engine

This report summarizes activities conducted in support of the project “A High Specific Output Gasoline Low Temperature Combustion Engine” under COOPERATIVE AGREEMENT NUMBER DE-EE0007788. This cooperative agreement was structured as a 51%/49% recipient/DOE NETL cost share with two Go / no-Go decision gates spanning three budget periods. The primary objective of the program is the development and demonstration of a downsized boosted, lean, low temperature gasoline combustion engine system capable of demonstrating a 15-17% fuel economy improvement relative to a contemporary naturally aspirated stoichiometric combustion engine consistent with relevant emissions constraints and the use of marketplace gasolines. The program focused on maximizing internal combustion engine fuel economy potential by combining the benefits of downsized boosted engine technology with next generation gasoline lean-burn, low temperature combustion and novel low temperature plasma ignition. The project achieved a 20.5% improvement from hot FTP cycle test and 18.9% improvement from cold FTP cycle test while meeting stringent SULEV30 emissions regulation for both test cycles (HOT FTP: 15.37 mg of NOx+HC; 0.16 g/mile of CO, COLD FTP: 23.1 mg of NOx+HC; 0.33 g/mile of CO).

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

QCD Equilibrium and Dynamical Properties from Holographic Black Holes

By using gravity/gauge correspondence, we employ an Einstein-Maxwell-Dilaton model to compute the equilibrium and out-of-equilibrium properties of a hot and baryon rich strongly coupled quark-gluon plasma. The family of 5-dimensional holographic black holes, which are constrained to mimic the lattice QCD equation of state at zero density, is used to investigate the temperature and baryon chemical potential dependence of the equation of state. We also obtained the baryon charge conductivity, and the bulk and shear viscosities with a particular focus on the behavior of these observables on top of the critical end point and the line of first order phase transition predicted by the model.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Plasma parameters and the reduction potential at a plasma-liquid interface

We report nonthermal plasmas in contact with liquids have been shown to generate a variety of reactive species capable of initiating reduction–oxidation (redox) reactions at the electrochemically active plasma–liquid interface. In conventional electrochemical cells, selective redox chemistry is achieved by controlling the reduction potential at the solid electrode–electrolyte interface by applying a bias via an external circuit. In the case of plasma–liquid systems, an analogous means of tuning the reduction potential near the interface has not clearly been identified. When treated as a floating surface, the liquid is expected to adopt a net negative charge to balance the flux of hot electrons and relatively cold positive ions. The reduction potential near the plasma–liquid interface is hypothesized to be proportional to the floating potential, which can be approximated using an analytical model provided the plasma parameters are known. Herein, we present a framework for correlating the electron density and electron temperature of a noble gas plasma jet to the reduction potential near the plasma–liquid interface. The plasma parameters were acquired for an argon atmospheric plasma jet in contact with an aqueous solution by means of laser Thomson scattering. The reduction potential was determined using identical reference electrodes to measure the potential difference between the plasma–liquid interface and bulk solution. Interestingly, the measured reduction potentials near the plasma–liquid interface were found to be in good agreement with the model-predicted values determined using the plasma parameters obtained from the Thomson scattering experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

An ignition criterion for inertial fusion boosted by microturbulence

Turbulence on fine spatial scales enhances fusion reactivity, enabling ignition at lower temperature. A modified Lawson-like ignition criterion is derived for inertially confined plasmas harboring turbulent kinetic energy. For some turbulent energy spectra, hot spots ignite at lower energy density and smaller volume. While detrimental mixing effects typically accompany turbulence and obscure these advantages, targets might be engineered to drive flow in regions where it is beneficial. The optimal length scale for this driving is identified, typically lying in the micrometer range.

Alpha particles↗
DOE OSTI2024

Extracting the speed of sound in quark–gluon plasma with ultrarelativistic lead–lead collisions at the LHC

Abstract Ultrarelativistic nuclear collisions create a strongly interacting state of hot and dense quark–gluon matter that exhibits a remarkable collective flow behavior with minimal viscous dissipation. To gain deeper insights into its intrinsic nature and fundamental degrees of freedom, we determine the speed of sound in an extended volume of quark–gluon plasma using lead–lead (PbPb) collisions at a center-of-mass energy per nucleon pair of 5.02 TeV. The data were recorded by the CMS experiment at the CERN LHC and correspond to an integrated luminosity of 0.607 nb −1 . The measurement is performed by studying the multiplicity dependence of the average transverse momentum of charged particles emitted in head-on PbPb collisions. Our findings reveal that the speed of sound in this matter is nearly half the speed of light, with a squared value of 0.241 ± 0.002 ( stat ) ± 0.016 ( syst ) in natural units. The effective medium temperature, estimated using the mean transverse momentum, is 219 ± 8 ( syst ) MeV . The measured squared speed of sound at this temperature aligns precisely with predictions from lattice quantum chromodynamic (QCD) calculations. This result provides a stringent constraint on the equation of state of the created medium and direct evidence for a deconfined QCD phase being attained in relativistic nuclear collisions.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

Plasma Facing Component Characterization and Correlation With Plasma Conditions in Lithium Tokamak Experiment-β

Lithium coatings in the Lithium Tokamak eXperiment (LTX) led to flat temperature profiles. The flat temperature profiles were observed along with a hot, low density edge, implying a broad, collisionless scrape-off layer (SOL). Additionally, in vacuo X-ray photoelectron spectroscopy (XPS) measurements established that lithium coatings evaporatively deposited onto high-Z plasma facing components (PFCs) became oxidized while retaining the ability to achieve good plasma performance long after lithium was applied to the PFCs. Longstanding theory predicted flat temperature profiles with low recycling walls, which was presumed to be due to hydrogen binding with elemental lithium to form lithium hydride. The presence of oxidized lithium, however, raised questions regarding the exact mechanism of hydrogen retention in LTX. To investigate these questions, the upgraded facility LTX- β includes a new sample exposure probe (SEP) for more detailed in vacuo analysis of PFC samples. The SEP is equipped with a vacuum suitcase capable of transporting samples representative of the LTX- β outer midplane PFCs to a stand-alone XPS system while maintaining pressures lower than the LTX- β base vacuum to limit the contamination between sample exposure and analysis. The low-energy resolution XPS system used in past experiments could only enable the determination of elemental percentages on the PFC sample surfaces. Because the new XPS system has higher energy resolution, it is more direct to assign chemical compounds to the measured binding energies. This capability has been confirmed by comparing XPS data from PFC test samples with measurements using a commercial high-resolution XPS system. Quartz crystal microbalances (QCMs) were used to quantify the thickness of the deposited lithium on the LTX- β PFCs. This article describes the application of the SEP to characterize the PFC surfaces using XPS and their relationship to plasma conditions.

Maan, Anurag↗
DOE OSTI2026

Utilizing the deuterium-tritium fusion resonance to diagnose thermal runaway in igniting plasmas

For high-efficiency inertial confinement fusion implosions, it is predicted that a burning hot spot will successfully encompass all surrounding fuel and then transition into a thermal runaway where the internal energy increase from fusion occurs on a timescale faster than the expansion of the fuel is able to quench the fusion chain reaction after ignition occurs. Observation of this dynamic phase transition would indicate distinct burn properties and indicate an implosion's robustness. A technique for diagnosing the presence of thermal runaway from measurements of nuclear reaction history is presented. The technique is based on taking the logarithmic derivative of the nuclear reaction history, called the 𝛼 curve, and allowing a mathematical decoupling of the mass, volume, and thermal reactivity in the fusion reaction rate equation. During thermal runaway, where the thermal temperature dominates the burn dynamics, a maximum in the 𝛼 curve is found where there is a maximum in the first derivative of the thermal fusion reactivity, an effect to the deuterium-tritium (DT) fusion cross-section resonance. This provides a distinct signature related to the fundamental nature of the DT fusion nuclear resonance and signifies the transition into the fusion thermal instability. Impacts of charged particle transport on the effect are also assessed and the analytical formulas are compared and found to be in agreement with radiation hydrodynamic codes.

high-energy-density plasmas↗
DOE OSTI2021

Looking through the photoionisation wake: Vela X-1 at φ orb ≈ 0.75 with Chandra /HETG

In this work, we detect and identify five narrow radiative recombination continua (Mg XI-XII, Ne IX-X, O VIII) and several emission lines from Fe, S, Si, Mg, Ne, Al, and Na, including four He-like triplets (S XV, Si XIII, Mg XI, and Ne IX). Photoionisation models reproduce the overall spectrum well, except for the near-neutral fluorescence lines of Fe, S, and Si. We conclude that the plasma is mainly photoionised, but more than one component is most likely present, which is consistent with a multi-phase plasma scenario, where denser and colder clumps of matter are embedded in the hot, photoionised wind of the companion star. Simulations with the future X-ray satellites Athena and XRISM show that a few hundred seconds of exposure is sufficient to disentangle the lines of the Fe Kα doublet and the He-like Fe XXV, improving, in general, the determination of the plasma parameters.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Variable magnetic field electron spectrometer to measure hot electrons in the range of 50–460 keV

Resonance absorption (RA) occurs when a p-polarized electromagnetic wave, obliquely incident on an inhomogeneous plasma, tunnels past its turning point and resonantly excites an electron plasma wave (EPW) at the critical density. This phenomenon is important, for instance, in the direct drive approach to inertial fusion energy and is a particular example of a wider phenomenon in plasma physics known as mode conversion, which is crucial for heating magnetic fusion devices, such as tokamaks, via RF heating. Direct measurement of these RA-generated EPW accelerated hot electrons, with energy in the range of a few tens to a few hundreds of keV, is a challenging task due to the relatively low deflecting magnetic fields needed. The solution described here is a magnetic electron spectrometer (MES) with a continually changing magnetic field, lower at the entrance of the MES and gradually increasing toward the end, that enables the measurement of a wide spectral range of electrons with energies between 50 and 460 keV. Electron spectra taken in a LaserNetUS RA experiment were acquired from plasmas generated by irradiating polymer targets with the combination of an ~300 ps pulse followed by a series of ten high intensity 50–200 fs duration laser pulses from the ALEPH laser at Colorado State University. In conclusion, the high intensity beam is designed as spike trains of uneven duration and delay pulses in order to modify the RA phenomenon.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Experimental achievement and signatures of ignition at the National Ignition Facility

An inertial fusion implosion on the National Ignition Facility, conducted on August 8, 2021 (N210808), recently produced more than a megajoule of fusion yield and passed Lawson's criterion for ignition [Phys. Rev. Lett. 129, 075001 (2022)]. Here we describe the experimental improvements that enabled N210808 and present the first experimental measurements from an igniting plasma in the laboratory. Ignition metrics like the product of hot-spot energy and pressure squared, in the absence of self-heating, increased by ~ 35%, leading to record values and an enhancement from previous experiments in the hot-spot energy (~ 3×), pressure (~ 2×), and mass (~ 2×). These results are consistent with self-heating dominating other power balance terms. The burn rate increases by an order of magnitude after peak compression, and the hot-spot conditions show clear evidence for burn propagation into the dense fuel surrounding the hot spot. These novel dynamics and thermodynamic properties have never been observed on prior inertial fusion experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Electron acceleration at oblique angles via stimulated Raman scattering at laser irradiance >10 16 W cm –2 μm 2

The generation of hot, directional electrons via laser-driven stimulated Raman scattering (SRS) is a topic of great importance in inertial confinement fusion (ICF) schemes. Little recent research has been dedicated to this process at high laser intensity, in which back, side, and forward scatter simultaneously occur in high energy density plasmas, of relevance to, for example, shock ignition ICF. In this paper, we present an experimental and particle-in-cell (PIC) investigation of hot electron production from SRS in the forward and near-forward directions from a single speckle laser of wavelength λ 0 = 1.053μm, peak laser intensities in the range I 0 = 0.2–1.0×10 17 Wcm –2 and target electron densities between ne = 0.3–1.6% n c , where n c is the plasma critical density. As the intensity and density are increased, the hot electron spectrum changes from a sharp cutoff to an extended spectrum with a slope temperature T = 34 ± 1 keV and maximum measured energy of 350 keV experimentally. Multidimensional PIC simulations indicate that the high energy electrons are primarily generated from SRS-driven electron plasma wave phase fronts with k vectors angled ~50° with respect to the laser axis. These results are consistent with analytical arguments that the spatial gain is maximized at an angle which balances the tendency for the growth rate to be larger for larger scattered light wave angles until the kinetic damping of the plasma wave becomes important. The efficiency of generated high energy electrons drops significantly with a reduction in either laser intensity or target electron density, which is a result of the rapid drop in growth rate of Raman scattering at angles in the forward direction.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Study of $\langle {p}_{\text{T}}\rangle$ and its higher moments, and extraction of the speed of sound in Pb-Pb collisions with ALICE

Ultrarelativistic heavy-ion collisions produce a state of hot and dense strongly interacting QCD matter called quark-gluon plasma (QGP). On an event-by-event basis, the volume of the QGP in ultracentral collisions is mostly constant, while its total entropy can vary significantly due to quantum fluctuations, leading to variations in the temperature of the system. Exploiting this unique feature of ultracentral collisions allows for the interpretation of the correlation of the mean transverse momentum ($\langle$p T $\rangle$) of produced charged hadrons and the number of charged hadrons as a measure for the speed of sound, c s . This speed is related to the rate at which compression waves travel in the QGP and is determined by fitting the relative increase in $\langle$p T $\rangle$ with respect to the relative change in the average charged-particle density ($\langle$dN ch /dη$\rangle$) measured at mid-rapidity. This study reports the event-average $\langle$p T $\rangle$ of charged particles as well as the variance, skewness, and kurtosis of the event-by-event transverse momentum per charged particle ([p T ]) distribution in ultracentral Pb-Pb collisions at a center-of-mass energy of 5.02 TeV per nucleon pair using the ALICE detector. Different centrality estimators based on charged-particle multiplicity or the transverse energy of the event are used to select ultracentral collisions. By ensuring a pseudorapidity gap between the region used to define the centrality and the region used to perform the measurement, the influence of biases and their potential effects on the rise of the mean transverse momentum is tested. The measured c$^{2}_{s}$ is found to strongly depend on the exploited centrality estimator and ranges between 0.1146±0.0028 (stat.)±0.0065 (syst.) and 0.4374±0.0006 (stat.)±0.0184 (syst.) in natural units. The self-normalized variance shows a steep decrease towards ultracentral collisions, while the self-normalized skewness variables show a maximum, followed by a fast decrease. These non-Gaussian features are understood in terms of the vanishing of the impact-parameter fluctuations contributing to the event-to-event [p T ] distribution.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

High-magnification Faraday rotation imaging and analysis of X-pinch implosion dynamics

An X-pinch load driven by an intense current pulse (>100 kA in ~100 ns) can result in the formation of a small radius, runaway compressional micro-pinch. A micro-pinch is characterized by a hot (>1 keV), current-driven (>100 kA), high-density plasma column (near solid density) with a small neck diameter (1–10 µm), a short axial extent (<1 mm), and a short duration (≲1 ns). With material pressures often well into the multi-Mbar regime, a micro-pinch plasma often radiates an intense, sub-ns burst of sub-keV to multi-keV x rays. A low-density coronal plasma immediately surrounding the dense plasma neck could potentially shunt current away from the neck and thus reduce the magnetic drive pressure applied to the neck. Here, to study the current distribution in the coronal plasma, a Faraday rotation imaging diagnostic (1064 nm) capable of producing simultaneous high-magnification polarimetric and interferometric images has been developed for the MAIZE facility at the University of Michigan. Designed with a variable magnification (1–10×), this diagnostic achieves a spatial resolution of ~35 µm, which is useful for resolving the ~100-μm-scale coronal plasma immediately surrounding the dense core. This system has now been used on a reduced-output MAIZE (100–200 kA, 150 ns) to assess the radial distribution of drive current immediately surrounding the dense micro-pinch neck. The total current enclosed was found to increase as a function of radius, r, from a value of ≈ 50 ± 25 kA at r ≈ 140 µm (at the edge of the dense neck) to a maximal value of ≈150 ± 75 kA for r ≥ 225 µm. This corresponds to a peak magnetic drive pressure of ≈75 ± 50 kbar at r ≈ 225 µm. The limitations of these measurements are discussed in the paper.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

High-Magnification Faraday Rotation Imaging and Analysis of X-pinch Implosion Dynamics

An X-pinch load driven by an intense current pulse (>100 kA in ~100 ns) can result in the formation of a small radius, runaway compressional micro-pinch. A micro-pinch is characterized by a hot (>1 keV), current-driven (>100 kA), high-density plasma column (near solid density) with a small neck diameter (1–10 μm), a short axial extent (<1 mm), and a short duration (.1 ns). With material pressures often well into the multi-Mbar regime, a micro-pinch plasma often radiates an intense, sub-ns burst of sub-keV to multi-keV x-rays. A low-density coronal plasma immediately surrounding the dense plasma neck could potentially shunt current away from the neck and thus reduce the magnetic drive pressure applied to the neck. To study the current distribution in the coronal plasma throughout the implosion process, a Faraday rotation imaging diagnostic (1064 nm) capable of producing simultaneous high-magnification polarimetric and interferometric images has been developed for the 1-MA, 100-ns MAIZE facility at the University of Michigan. Designed with a variable magnification (1–10&times;), this diagnostic achieves a spatial resolution of approximately 35 μm, which is useful for resolving the ~100-μm-scale coronal plasma region immediately surrounding the dense core. Combined with the corresponding interferogram, which provides the radial density distribution in the low-density coronal plasma, the measured rotation can be used to diagnose the delivery of the driver current, and thus the magnetic drive pressure, to the micro-pinch plasma as it approaches minimal radius. Using this technique on MAIZE, we have measured

Dowhan, G. V.↗
DOE OSTI2022

Hot-electron preheat and mitigation in polar-direct-drive experiments at the National Ignition Facility

Target preheat by superthermal electrons from laser–plasma instabilities is a major obstacle to achieving thermonuclear ignition via direct-drive inertial confinement fusion at the National Ignition Facility (NIF). Polar-direct-drive surrogate plastic implosion experiments were performed on the NIF to quantify preheat levels at ignition-relevant scale and develop mitigation strategies. Here, the experiments were used to infer the hot-electron temperature, energy fraction, divergence, and to directly measure the spatial hot-electron energy deposition profile inside the imploding shell. Silicon layers buried in the ablator are shown to mitigate the growth of laser–plasma instabilities and reduce preheat, providing a promising path forward for ignition designs at an on-target intensity of about 10 15 W/cm 2 .

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Black Hole Flares: Ejection of Accreted Magnetic Flux through 3D Plasmoid-mediated Reconnection

Magnetic reconnection can power bright, rapid flares originating from the inner magnetosphere of accreting black holes. We conduct extremely high-resolution (5376 × 2304 × 2304 cells) general-relativistic magnetohydrodynamics simulations, capturing plasmoid-mediated reconnection in a 3D magnetically arrested disk for the first time. We show that an equatorial, plasmoid-unstable current sheet forms in a transient, nonaxisymmetric, low-density magnetosphere within the inner few Schwarzschild radii. Magnetic flux bundles escape from the event horizon through reconnection at the universal plasmoid-mediated rate in this current sheet. The reconnection feeds on the highly magnetized plasma in the jets and heats the plasma that ends up trapped in flux bundles to temperatures proportional to the jet's magnetization. The escaped flux bundles can complete a full orbit as low-density hot spots, consistent with Sgr A* observations by the GRAVITY interferometer. Reconnection near the horizon produces sufficiently energetic plasma to explain flares from accreting black holes, such as the TeV emission observed from M87. The drop in the mass accretion rate during the flare and the resulting low-density magnetosphere make it easier for very-high-energy photons produced by reconnection-accelerated particles to escape. The extreme-resolution results in a converged plasmoid-mediated reconnection rate that directly determines the timescales and properties of the flare.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Time-resolved measurements of HO 2 radical in a heated plasma flow reactor

Time-resolved, absolute HO 2 number density in diluted H 2 –O 2 –Ar, CH 4 –O 2 -Ar, and C 2 H 4 –O 2 –Ar mixtures excited by a repetitive ns pulse discharge in a heated plasma flow reactor is measured by Cavity Ringdown Spectroscopy (CRDS). The experimental results are obtained at $\textit{T}$ = 300-600 K and $\textit{P}$ = 130 Torr, both during the discharge pulse burst and in the afterglow. In this work, the HO 2 number density is inferred from the CRDS data using a spectral model exhibiting good agreement with previous measurements of absolute HO 2 absorption cross sections. In the room-temperature H 2 –O 2 mixture, as well as in CH 4 –O 2 and C 2 H 4 –O 2 mixtures over the entire temperature range studied, HO2 is generated only during the discharge burst and decays in the afterglow. However, in the H 2 –O 2 mixture at elevated temperatures, $\textit{T}$ = 400-600 K, HO 2 persists in the afterglow up to 10 ms after the discharge burst, comparable with the flow residence time in the reactor. Comparison with kinetic modeling shows that the sustained reactivity after the source of radicals is turned off is due to a chain propagation / hydrogen oxidation process, which dominates the radical recombination reactions. The kinetic modeling predictions are in good agreement with the relative HO 2 number density measured in all three mixtures, although the model underpredicts the absolute number densities in H 2 –O 2 at $\textit{T}$ = 400-600 K by up to a factor of two. Detection of the sustained low-temperature reactivity in H 2 –O 2 , initiated by the radical generation in the plasma, suggests that the plasma excitation may also affect kinetics of oxidation and reforming of fuels exhibiting low-temperature chemistry below hot ignition point.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

ITER cold VDEs in the limit of perfectly conducting walls

Recently, it has been shown that a vertical displacement event (VDE) can occur in ITER even when the walls are perfect conductors, as a consequence of the current quench (CQ) [A. H. Boozer, Phys. Plasmas 26, 114501 (2019)]. We used the extended-MHD code M3D-C1 with an ITER-like equilibrium and induced a CQ to explore cold VDEs in the limit of perfectly conducting walls, using different wall geometries. In the case of a rectangular first wall with the side walls far away from the plasma, we obtained very good agreement with the analytical model developed by Boozer that considers a top/bottom flat-plates wall. We show that the solution in which the plasma remains at the initial equilibrium position is improved when bringing the side walls closer to the plasma. When approximating the ITER first wall as a perfect conductor, the plasma remains stable at the initial equilibrium position far beyond the value predicted by the flat-plates wall limit. When considering an opposite limit in which only the inner shell of the ITER vacuum vessel acts as a perfect conductor, the plasma is displaced during the CQ, but the edge safety factor remains above 2 longer in the current decay compared to the flat-plates wall limit. In all the simulated cases, the VDE is found to be strongly dependent on the plasma current, in agreement with a similar finding in the flat-plates wall limit, showing an important difference with hot VDEs in which the CQ is not a necessary condition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗