Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “grain boundary diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Simultaneous shunt protection and back contact formation for CdTe solar cells with single wall carbon nanotube layers

Thin film photovoltaic (PV) devices and modules prepared by commercial processes can be severely compromised by through-device low resistance electrical pathways. The defects can be due to thin or missing semiconductor material, metal diffusion along grain boundaries, or areas containing diodes with low turn-on potentials. We report the use of single wall carbon nanotube (SWCNT) layers to enable both protection against these defects and back contact formation for CdTe PV devices. Samples prepared with a SWCNT back contact exhibited good efficiency and did not require shunt protection, while devices prepared without shunt protection using a standard metal back contact performed poorly. We describe the mechanism by which the SWCNT layer functions. In addition to avoiding the need for shunt protection by other means, the SWCNT film also provides a route to higher short circuit currents.

14 SOLAR ENERGY↗

STEM/EELS Study of Fission Product Transport in Neutron Irradiated TRISO Fuel Particles (NSUF report)

The objectives of this project are to study the distribution, composition and structure of fission products in neutron irradiated SiC layer of the TRISO particles, using electron microscopy including scanning transmission electron microscopy (STEM), energy dispersive x-ray spectroscopy (EDS), electron energy loss spectroscopy (EELS), high-resolution transmission electron microscopy (HRTEM) and precession electron diffraction (PED), in an effort to enhance the understanding of distribution, composition, structure and transport mechanisms of fission products. In the past 40 years, numerous studies, including reactor experiments, out-of-pile experiments, and simulations, have been performed to investigate the fission product transport behavior and mechanisms. Grain boundary (GB) diffusion, neutron-induced diffusion, catalytic Pd-assisted transport, and vapor-phase migration all have been suggested as possible governing transport mechanisms. The previous studies, however, have not been able to reproduce the transport behavior of fission products and the mechanisms remain poorly understood. This project is anticipated to contribute to enhancing the understanding of the mechanisms of fission product transport in irradiated SiC layer of the TRISO particles. Thorough understanding of fission product transport mechanisms in the SiC layer will improve fuel modeling and design and better SiC layers and TRISO coated particles can be designed to enhance retention of fission products and reduce their release. Eventually, TRISO coated particles with improved performance can be fabricated, and such advancement will expedite the qualifying and licensing processes for TRISO coated particles. Hence, this research is contributing to achieving the objectives of DOE-NE to develop the next generation nuclear reactors, particularly high-temperature gas reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Liquid Metal Intrusion Testing Final Report

Los Alamos National Lab (LANL) is concerned about potential interactions between a tin-antimony pewter material used for localized radiation shielding and stainless-steel containers used for storage and movement of radioactive materials when containers are subjected to elevated temperatures. The specific concern is whether pewter constituents can diffuse into grain boundaries and lead to embrittlement of the stainless steel, potentially compromising the ability of stainless steel components to maintain containment. This work will provide a qualitative and quantitative understanding of the depth of penetration of the pewter coating constituents into stainless steel when the test coupons are subjected to a range of thermal environments. The results of the present work will allow LANL to determine conditions for safely using the pewter lined containers.

36 MATERIALS SCIENCE↗

Development of bubble evolution model for new mechanistic transient fission gas release capability in BISON

This report summarizes efforts within NEAMS to investigate the mechanisms that govern fission gas behavior in UO 2 . In particular, the focus is on understanding how fission gas behavior causes transient fission gas release and fragmentation/pulverization of high burnup structure (HBS) in UO 2 . HBS forms in the periphery of the pellet where temperatures are relatively low. Previously, MD simulations were performed to determine the reaction energies for various Xe and U defects with bubbles, as a function of Xe to vacancy ratio or, equivalently, pressure. As had been shown in FY22, it was found that the unmodified version of the Simple Integrated Fission Gas Release and Swelling (SIFGRS) model within BISON greatly over-predicted the number gas atoms per vacancy in the bubbles in the outer rim of the pellet (a ratio of > 1 million). This was due to slow grain boundary vacancy diffusivity and not accounting for the pressure-dependent reaction energy for Xe interstitials with bubbles. The application of the pressure dependent reaction energies was able to restrict Xe to vacancy ratios to 2:1, which is far more realistic than those originally obtained from SIFGRS.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Multiscale Thermomechanical Damage Model with Internal State Variables for Ceramic Matrix Composites

A length scale-dependent matrix damage model has been developed to simulate the response of ceramic matrix composites (CMCs). This model captures damage initiation and propagation in the brittle matrix material by employing internal state variable (ISV) theory within a multiscale modeling framework to obtain damaged matrix stress-strain constitutive relationships at each length scale. Material degradation due to matrix cracking is captured by a damage variable determined using fracture mechanics and the self-consistent scheme. An additional state variable is introduced to capture the nucleation and growth of matrix porosity, a key mechanism contributing to matrix nonlinearity. Porosity occurs as a result of material diffusion around grain boundaries and the growth of the porosity state variable is related to the material entropy dissipation and the volumetric strain. The nonlinear predictive capabilities of the material model are demonstrated for monolithic silicon carbide, unidirectional (UD) carbon fiber/silicon carbide matrix (C/SiC) CMC, and five-harness satin (5HS) woven C/SiC CMC.

Skinner, Travis D.↗

Elevated temperature deformation of TD-nickel base alloys

Sensitivity of the elevated temperature deformation of TD-nickel to grain size and shape was examined in both tension and creep. Elevated temperature strength increased with increasing grain diameter and increasing L/D ratio. Measured activation enthalpies in tension and creep were not the same. In tension, the internal stress was not proportional to the shear modulus. Creep activation enthalpies increased with increasing L/D ratio and increasing grain diameter, to high values compared with that of the self diffusion enthalpy. It has been postulated that two concurrent processes contribute to the elevated temperature deformation of polycrystalline TD-nickel: (1) diffusion controlled grain boundary sliding, and (2) dislocation motion.

Petrovic, J. J.↗

Elevated temperature deformation of thoria dispersed nickel-chromium

The deformation behavior of thoria nickel-chromium (TD-NiCr) was examined over the temperature range 593 C (1100 F) to 1260 C (2300 F) in tension and compression and at 1093 C (2000 F) in creep. Major emphasis was placed on: (1) the effects of the material and test related variables (grain size, temperature, stress and strain rate) on the deformation process; and (2) the evaluation of single crystal TD-NiCr material produced by a directional recrystallization process. Elevated temperature yield strength levels and creep activation enthalpies were found to increase with increasing grain size reaching maximum values for the single crystal TD-NiCr. Stress exponent of the steady state creep rate was also significantly higher for the single crystal TD-NiCr as compared to that determined for the polycrystalline materials. The elevated temperature deformation of TD-NiCr was analyzed in terms of two concurrent, parallel processes: diffusion controlled grain boundary sliding, and dislocation motion.

Kane, R. D.↗

Creep deformation of TD-nickel chromium

An investigation was conducted of the mechanical behavioral characteristics of thoria-dispersed (TD) NiCr materials at elevated temperatures. The experimental procedure used is discussed along with the significance of the obtained results. Attention is given to basic creep behavior and creep thermal activation parameter measurements. It is found that the overall creep behavior of TD-NiCr can be explained on the basis of the relative contributions of two parallel-concurrent deformation mechanisms, including diffusion controlled grain boundary sliding and dislocation motion.

Kane, R. D.↗

Analysis of defect structure in silicon. Characterization of samples from UCP ingot 5848-13C

Statistically significant quantitative structural imperfection measurements were made on samples from ubiquitous crystalline process (UCP) Ingot 5848 - 13 C. Important trends were noticed between the measured data, cell efficiency, and diffusion length. Grain boundary substructure appears to have an important effect on the conversion efficiency of solar cells from Semix material. Quantitative microscopy measurements give statistically significant information compared to other microanalytical techniques. A surface preparation technique to obtain proper contrast of structural defects suitable for QTM analysis was perfected.

Natesh, R.↗

Analysis of defect structure in silicon. Characterization of SEMIX material. Silicon sheet growth development for the large area silicon sheet task of the low-cost solar array project

Statistically significant quantitative structural imperfection measurements were made on samples from ubiquitous crystalline process (UCP) Ingot 5848 - 13C. Important correlation was obtained between defect densities, cell efficiency, and diffusion length. Grain boundary substructure displayed a strong influence on the conversion efficiency of solar cells from Semix material. Quantitative microscopy measurements gave statistically significant information compared to other microanalytical techniques. A surface preparation technique to obtain proper contrast of structural defects suitable for quantimet quantitative image analyzer (QTM) analysis was perfected and is used routinely. The relationships between hole mobility and grain boundary density was determined. Mobility was measured using the van der Pauw technique, and grain boundary density was measured using quantitative microscopy technique. Mobility was found to decrease with increasing grain boundary density.

Natesh, R.↗

High temperature tensile and creep behaviour of low pressure plasma-sprayed Ni-Co-Cr-Al-Y coating alloy

The high temperature tensile and creep behavior of low pressure plasma-sprayed plates of a typical Ni-Co-Cr-Al-Y alloy has been studied. From room temperature to 800 K, the Ni-Co-Cr-Al-Y alloy studied has nearly a constant low ductility and a high strength. At higher temperatures, it becomes weak and highly ductile. At and above 1123 K, the behavior is highly dependent on strain rate and exhibits classic superplastic characteristics with a high ductility at intermediate strain rates and a strain rate sensitivity of about 0.5. At either higher or lower strain rates, the ductility decreases and the strain rate sensitivities are about 0.2. In the superplastic deformation range, the activation energy for creep is 120 + or - 20 kJ/mol, suggesting a diffusion-aided grain boundary sliding mechanism. Outside the superplastic range, the activation energy for creep is calculated to be 290 + or - 20 kJ/mol.

Hebsur, M. G.↗

Atomistic modeling of metal–nonmetal interphase boundary diffusion

Atomistic computer simulations are applied to investigate the atomic structure, thermal stability, and diffusion processes in Al–Si interphase boundaries as a prototype of metal–ceramic interfaces in composite materials. Some of the most stable orientation relationships between the phases found in this work were previously observed in epitaxy experiments. Here, a non-equilibrium interface can transform to a more stable state by a mechanism that we call interface-induced recrystallization. Diffusion of both Al and Si atoms in stable Al–Si interfaces is surprisingly slow compared with diffusion of both elements in Al grain boundaries but can be accelerated in the presence of interface disconnections. A qualitative explanation of the sluggish interphase boundary diffusion is proposed. Atomic mechanisms of interphase boundary diffusion are similar to those in metallic grain boundaries and are dominated by correlated atomic rearrangements in the form of strings and rings of collectively moving atoms.

36 MATERIALS SCIENCE↗

Precipitation behavior and phase transformation mechanism of super austenitic stainless steel S32654 during isothermal aging

Highlights: • σ phase formed following a sequence: intergranular, cellular and intragranular. • Cellular σ phase was firstly detected in S32654 aged at 800–900 °C. • Cellular σ growth is controlled by both intergranular and bulk Cr, Mo diffusion. • N-rich zone and Cr diffusion near σ phase induced the nucleation of Cr{sub 2}N. • Local needle-like σ transformed into Cr{sub 2}N and R phase through Cr, Mo diffusion. - Abstract: Thermodynamic calculation as well as microstructure characterization was carried out to investigate the precipitation behavior of super austenitic stainless steel S32654 aged at 700–1100 °C. The corresponding precipitation characteristics and transformation mechanisms of secondary phases were proposed. The results demonstrate that σ phases with various morphologies formed during isothermal aging, and followed a sequence of intergranular, cellular and intragranular with aging temperature. The intergranular σ phase nucleated much faster than the intragranular one due to the lower nucleation energy and higher element diffusion rate at grain boundary. Most intragranular σ phase grew into needle-like shape because of the great difference in mobility of the interfaces formed around it. The cellular σ phase was firstly detected in S32654, and its growth process was successively controlled by intergranular diffusion and then by bulk diffusion of Cr and Mo. Both Cr and Mo bulk diffusion and large needle-like σ phase resulted in the incompleteness of cellular precipitation of σ phase. Another new phenomenon was found that σ phase could induce the precipitation of Cr{sub 2}N ahead of cell boundary, between lamellar σ phases and at the σ/γ interfaces. Meanwhile, local parts of needle-like σ phase gradually transformed into Cr{sub 2}N and R phase through Cr and Mo diffusion from the former to the latters.

36 MATERIALS SCIENCE↗

Effect of stacking sequence on crystallization in Al/a-Ge bilayer thin films

Two types of bilayer thin films with different deposition sequences, i.e., amorphous Ge under Al (a-Ge/Al) and the inverse (Al/a-Ge), were prepared by magnetron sputtering at room temperature. In-situ and ex-situ thermal annealing were compared to study the effect of the stacking sequence on crystallization of amorphous Ge. Although metal-induced crystallization occurred in both cases at low temperature, layer exchange was observed only in a-Ge/Al. In fact, compressive stress could usually be produced when Ge atoms diffused into Al grain boundaries and crystallized there. In the a-Ge/Al system, the stress could be released through diffusion of Al atoms onto the surface and formation of hillocks. Thus, grain boundary (GB) mediated crystallization was dominant in the whole process and layer exchange occurred. However, in the Al/a-Ge system, it was difficult for stress to be relaxed because the Ge sublayer and substrate restricted the diffusion of Al atoms. GB-mediated crystallization was, therefore, considerably suppressed and interface-mediated crystallization was preferred without layer exchange. This leads to distinct morphologies of dendrites in the two systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

CVD-Based Valence-Mending Passivation for Crystalline-Si Solar Cells

The objective of this project is to investigate a new surface passivation technique, valence-mending passivation, for its applications in crystalline-Si solar cells to achieve significant efficiency improvement and cost reduction. As the enabling technique, the project includes the development of chemical vapor deposition recipes to passivate textured Si(100) and multicrystalline-Si surfaces by sulfur and the characterization of the passivated Si surfaces, including thermal stability, Schottky barrier height, contact resistance and surface recombination. One important application is to replace the Ag finger electrode in Si cells with Al to reduce cost, by ~$0.1/Wp, and allow terawatt-scale deployment of crystalline-Si solar cells. These all-Al Si cells require a low-temperature metallization process for the Al electrode, to be compatible with valence-mending passivation and to prevent Al diffusion into n-type Si. Another application is to explore valence-mending passivation of grain boundaries in multicrystalline Si by diffusing sulfur into grain boundaries, to reduce the efficiency gas between monocrystalline-Si solar cells and multicrystalline-Si cells. The major accomplishments of this project include: 1) Demonstration of chemical vapor deposition processes for valence-mending passivation of both monocrystalline Si(100) and multicrystalline Si surfaces. Record Schottky barriers have been demonstrated, with the new record-low barrier of less than 0.08 eV between Al and sulfur-passivated n-type Si(100) and the new record-high barrier of 1.14 eV between Al and sulfur-passivated p-type Si(100). On the textured p-type monocrystalline Si(100) surface, the highest barrier with Al is 0.85 eV by valence-mending passivation. 2) Demonstration of a low-temperature metallization process for Al in crystalline-Si solar cells. The new metallization process is based on electroplating of Al in a room-temperature ionic liquid. The resistivity of the electroplated Al is ~7×10–6 ohm-cm, similar to that of screen-printed Ag. 3) Demonstration of two all-Al, Ag-free Si solar cells, with an electroplated Al front electrode and a screen-printed Al back electrode. One cell is an industrial p-type front-emitter cell, and the other is an n-type back-emitter cell. The efficiency of the p-type cell is close to 15%. This is an industrial cell and its efficiency is capped at ~18%. 4) Demonstration of grain boundary passivation by both hydrogen and sulfur using hydrogen sulfide (H2S). When the new grain boundary passivation is combined with Al2O3 surface passivation and post-annealing, the minority carrier lifetime in the p-type multicrystalline Si samples shows a significant improvement up to 68 fold. 5) In a side project, a simple green process is developed which is capable of recycling over 90% of the Si material in end-of-life crystalline-Si solar cells. The recycled Si meets the specifications for solar-grade Si and can be used as a new poly-Si feedstock for ingot growth.

14 SOLAR ENERGY↗

Role of W and Mn for reliable 1X nanometer-node ultra-large-scale integration Cu interconnects proved by atom probe tomography

We used atom probe tomography (APT) to study the use of a Cu(Mn) as a seed layer of Cu, and a Co(W) single-layer as reliable Cu diffusion barriers for future interconnects in ultra-large-scale integration. The use of Co(W) layer enhances adhesion of Cu to prevent electromigration and stress-induced voiding failures. The use of Cu(Mn) as seed layer may enhance the diffusion barrier performance of Co(W) by stuffing the Cu diffusion pass with Mn. APT was used to visualize the distribution of W and Mn in three dimensions with sub-nanometer resolution. W was found to segregate at the grain boundaries of Co, which prevents diffusion of Cu via the grain boundaries. Mn was found to diffuse from the Cu(Mn) layer to Co(W) layer and selectively segregate at the Co(W) grain boundaries with W, reinforcing the barrier properties of Co(W) layer. Hence, a Co(W) barrier coupled with a Cu(Mn) seed layer can form a sufficient diffusion barrier with film that is less than 2.0-nm-thick. The diffusion barrier behavior was preserved following a 1-h annealing at 400 °C. The underlayer of the Cu interconnects requires a large adhesion strength with the Cu, as well as low electrical resistivity. The use of Co(W) has previously been shown to satisfy these requirements, and addition of Mn is not expected to deteriorate these properties.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thermally stable perpendicular magnetic anisotropy features of Ta/TaO{sub x}/Ta/CoFeB/MgO/W stacks via TaO{sub x} underlayer insertion

We report that a TaO{sub x} underlayer enhances the stability of perpendicular magnetic anisotropy (PMA) in TaO{sub x}/Ta/CoFeB/MgO stacks during annealing; control of oxygen content in the TaO{sub x} layer is critical. X-ray photoelectron spectroscopy observations revealed clear suppression of Ta atom diffusion towards the CoFeB/MgO interface or MgO regions. The TaO{sub x} underlayer possibly served as a diffusion sponge, permitting some thermally activated Ta atoms to impregnate the TaO{sub x} underlayer via a diffusion path, such as grain boundaries. We propose a possible mechanism for enhanced PMA stability based on diffusion of thermally activated Ta atoms.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗