SEARCH · Engineering Papers

Results for “geometry optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS2014

Aerostructural Level Set Topology Optimization for a Common Research Model Wing

The purpose of this work is to use level set topology optimization to improve the design of a representative wing box structure for the NASA common research model. The objective is to minimize the total compliance of the structure under aerodynamic and body force loading, where the aerodynamic loading is coupled to the structural deformation. A taxi bump case was also considered, where only body force loads were applied. The trim condition that aerodynamic lift must balance the total weight of the aircraft is enforced by allowing the root angle of attack to change. The level set optimization method is implemented on an unstructured three-dimensional grid, so that the method can optimize a wing box with arbitrary geometry. Fast matching and upwind schemes are developed for an unstructured grid, which make the level set method robust and efficient. The adjoint method is used to obtain the coupled shape sensitivities required to perform aerostructural optimization of the wing box structure.

Dunning, Peter D.↗

NASA NTRS2020

SCExAO/CHARIS Near-infrared Integral Field Spectroscopy of the HD 15115 Debris Disk

We present new, near-infrared (1.1–2.4 μm) high-contrast imaging of the debris disk around HD 15115 with the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) system coupled with the Coronagraphic High Angular Resolution Imaging Spectrograph (CHARIS). The SCExAO/CHARIS resolves the disk down to ρ ∼ 0."2 (r(proj) ∼ 10 au), a factor of ∼3–5 smaller than previous recent studies. We derive a disk position angle of PA ∼ 279.°4–280.°5 and an inclination of i ∼ 85.°3–86.2.°. While recent SPHERE/IRDIS imagery of the system could suggest a significantly misaligned two-ring disk geometry, CHARIS imagery does not reveal conclusive evidence for this hypothesis. Moreover, optimizing models of both one- and two-ring geometries using differential evolution, we find that a single ring having a Hong-like scattering phase function matches the data equally well within the CHARIS field of view (ρ ≲ 1''). The disk's asymmetry, well evidenced at larger separations, is also recovered; the west side of the disk appears, on average, around 0.4 mag brighter across the CHARIS bandpass between 0farcs25 and 1''. Comparing Space Telescope Imaging Spectrograph (STIS) 50CCD optical photometry (2000–10500 Å) with CHARIS near-infrared photometry, we find a red (STIS/50CCD−CHARIS broadband) color for both sides of the disk throughout the 0farcs4–1'' region of overlap, in contrast to the blue color reported at similar wavelengths for regions exterior to ∼2''. Further, this color may suggest a smaller minimum grain size than previously estimated at larger separations. Finally, we provide constraints on planetary companions and discuss possible mechanisms for the observed inner disk flux asymmetry and color.

Kellen Lawson↗

NASA NTRS2003

Nonlinear Resonant Oscillations of Gas in Optimized Acoustical Resonators and the Effect of Central Blockage

Optimizing resonator shapes for maximizing the ratio of maximum to minimum gas pressure at an end of the resonator is investigated numerically. It is well known that the resonant frequencies and the nonlinear standing waveform in an acoustical resonator strongly depend on the resonator geometry. A quasi-Newton type scheme was used to find optimized axisymmetric resonator shapes achieving the maximum pressure compression ratio with an acceleration of constant amplitude. The acoustical field was solved using a one-dimensional model, and the resonance frequency shift and hysteresis effects were obtained through an automation scheme based on continuation method. Results are presented for optimizing three types of geometry: a cone, a horn-cone and a half cosine- shape. For each type, different optimized shapes were found when starting with different initial guesses. Further, the one-dimensional model was modified to study the effect of an axisymmetric central blockage on the nonlinear standing wave.

Li, Xiao-Fan↗

NASA NTRS2003

Nonlinear Resonant Oscillations of Gas in Optimized Acoustical Resonators and the Effect of Central Blockage

Optimizing resonator shapes for maximizing the ratio of maximum to minimum gas pressure at an end of the resonator is investigated numerically. It is well known that the resonant frequencies and the nonlinear standing waveform in an acoustical resonator strongly depend on the resonator geometry. A quasi-Newton type scheme was used to find optimized axisymmetric resonator shapes achieving the maximum pressure compression ratio with an acceleration of constant amplitude. The acoustical field was solved using a one-dimensional model, and the resonance frequency shift and hysteresis effects were obtained through an automation scheme based on continuation method. Results are presented for optimizing three types of geometry: a cone, a horn-cone and a half cosine-shape. For each type, different optimized shapes were found when starting with different initial guesses. Further, the one-dimensional model was modified to study the effect of an axisymmetric central blockage on the nonlinear standing wave.

Li, Xiaofan↗

NASA NTRS1990

Mission and sampling analyses for atmospheric satellite experiments

Orbital analyses, instrument-viewing geometry studies, and sampling simulations are performed to define mission concepts for advanced atmospheric research satellite experiments. These analyses are conducted in collaboration with NASA Headquarters and working groups consisting of atmospheric scientists and experiment developers. Analytical techniques are developed and used to optimize geographical coverage, sensor-viewing geometries, data gathering strategies, sampling schemes, orbital characteristics, satellite launch times, and operational modes of the various experiments and mission concepts. Short-term (7 day) Shuttle Missions, the Upper Atmosphere Research Satellite (UARS), and multisatellite missions such as the Earth Observing System (EOS) are being studied. Atmospheric experiments which are being analyzed include nadir-viewing sounders, limb-emission scanners, laser systems, and solar-occultation techniques.

Harrison, Edwin F.↗

NASA NTRS1982

The use of optimization techniques to design controlled diffusion compressor blading

A method for automating compressor blade design using numerical optimization, and applied to the design of a controlled diffusion stator blade row is presented. A general purpose optimization procedure is employed, based on conjugate directions for locally unconstrained problems and on feasible directions for locally constrained problems. Coupled to the optimizer is an analysis package consisting of three analysis programs which calculate blade geometry, inviscid flow, and blade surface boundary layers. The optimizing concepts and selection of design objective and constraints are described. The procedure for automating the design of a two dimensional blade section is discussed, and design results are presented.

Sanger, N. L.↗

NASA NTRS2017

Reconfigurable Cellular Composite Structures for Lighter than Air Vehicles with Scalable Size and Endurance

Engineered non-stochastic cellular materials show promising characteristics on the laboratory scale,with nearly ideal specific stiffness and strength scaling at ultralight mass density. These propertiessuggest performance benefits in any application with combined stiffness and mass constraints, suchas air vehicles. We investigate here the application of re-configurable cellular composite materialsand structures to lighter than air vehicles. We describe the properties and applicability of these materials,provide an example analysis of governing loading conditions associated with airships, showan example optimization method for navigating the design space, and describe how recent advancesin cellular material manufacturing and reconfiguration enable system performance benefits includingnew concepts of operation. Lastly, we propose lighter than air vehicles that are assembled andmaintained in-flight, eliminating structural compromises associated with transitional flight modesand ground handling.Engineered non-stochastic cellular material properties suggest performance benefits in lighter than air vehicles due tostiffness and mass constraints that are intrinsic to the airship design problem. Recent advances in cellular materialmanufacturing and reconfiguration enable system performance benefits including new concepts of operation, such aslighter than air vehicles that are assembled and maintained in-flight, eliminating structural compromises associatedwith transitional flight modes and ground handling. Existing engineered cellular materials display properties allowinglarge large scale airships design as monocoque cellular solids. Inevitable improvements in cellular material propertiesand manufacturing will improve feasibility even further. Given the suggestion that the two most significant technologygaps exist across all current airship projects are manufacturing and assembly processes and ground handling [7],a strategy that encompasses construction and maintenance in flight could provide critical rephrasing of the systemdesign problem through these new concepts of operation. Refactoring of traditional manufacturing, operation, andservice process constraints could extend to other domains in aerospace systems and manufacturing in general.In future work, the complexity of the design task would benefit from a form of optimization in order to find themost suitable geometry for a chosen application. For example, the Sequential Least SQuares Programming (SLSQP)function from within the SciPy Minimize library is a multiobjective constrained optimization method that has beenapplied to fixed wing aircraft design. [17] In this situation it would allow for several objective functions such as drag,bending stiffness, buoyancy and cost of transport to be incorporated into a composite objective function.

Copplestone, Grace↗

NASA NTRS1982

Mathematical models for the synthesis and optimization of spiral bevel gear tooth surfaces

The geometry of spiral bevel gears and to their rational design are studied. The nonconjugate tooth surfaces of spiral bevel gears are, in theory, replaced (or approximated) by conjugated tooth surfaces. These surfaces can be generated by two conical surfaces, and by a conical surface and a revolution. Although these conjugated tooth surfaces are simpler than the actual ones, the determination of their principal curvatures and directions is still a complicated problem. Therefore, a new approach, to the solution of these is proposed. Direct relationships between the principal curvatures and directions of the tool surface and those of the generated gear surface are obtained. With the aid of these analytical tools, the Hertzian contact problem for conjugate tooth surfaces can be solved. These results are useful in determining compressive load capacity and surface fatigue life of spiral bevel gears. A general theory of kinematical errors exerted by manufacturing and assembly errors is developed. This theory is used to determine the analytical relationship between gear misalignments and kinematical errors. This is important to the study of noise and vibration in geared systems.

Litvin, F. L.↗

NASA NTRS1990

Computational analysis of flow in 3D propulsive transition ducts

A numerical analysis of fully three dimensional, statistically steady flows in propulsive transition ducts being considered for use in future aircraft of higher maneuverability is investigated. The purpose of the transition duct is to convert axisymmetric flow from conventional propulsion systems to that of a rectangular geometry of high aspect ratio. In an optimal design, the transition duct would be of minimal length in order to reduce the weight penalty, while the geometrical change would be gradual enough to avoid detrimental flow perturbations. Recent experiments conducted at the Propulsion Aerodynamics Branch have indicated that thrust losses in ducts of superelliptic cross-section can be surprisingly low, even if flow separation occurs near the divergent walls. In order to address the objective of developing a rational design procedure for optimal transition ducts, it is necessary to have available a reliable computational tool for the analysis of flows achieved in a sequence of configurations. Current CFD efforts involving complicated geometries usually must contend with two separate but interactive aspects: namely, grid generation and flow solution. The first two avenues of the present investigation were comprised of suitable grid generation for a class of transition ducts of superelliptic cross-section, and the subsequent application of the flow solver PAB3D to this geometry. The code, PAB3D, was developed as a comprehensive tool for the solution of both internal and external high speed flows. The third avenue of investigation has involved analytical formulations to aid in the understanding of the nature of duct flows, and also to provide a basis of comparison for subsequent numerical solutions. Numerical results to date include the generation of two preliminary grid systems for duct flows, and the initial application of PAB3D to the corresponding geometries, which are of the class tested experimentally.

Sepri, Paavo↗

NASA NTRS1991

Design, optimization, and analysis of a self-deploying PV tent array

A tent shaped PV array was designed and the design was optimized for maximum specific power. In order to minimize output power variation a tent angle of 60 deg was chosen. Based on the chosen tent angle an array structure was designed. The design considerations were minimal deployment time, high reliability, and small stowage volume. To meet these considerations the array was chosen to be self-deployable, form a compact storage configuration, using a passive pressurized gas deployment mechanism. Each structural component of the design was analyzed to determine the size necessary to withstand the various forces to which it would be subjected. Through this analysis the component weights were determined. An optimization was performed to determine the array dimensions and blanket geometry which produce the maximum specific power for a given PV blanket. This optimization was performed for both lunar and Martian environmental conditions. Other factors such as PV blanket types, structural material, and wind velocity (for Mars array), were varied to determine what influence they had on the design point. The performance specifications for the array at both locations and with each type of PV blanket were determined. These specifications were calculated using the Arimid fiber composite as the structural material. The four PV blanket types considered were silicon, GaAs/Ge, GaAsCLEFT, and amorphous silicon. The specifications used for each blanket represented either present day or near term technology. For both the Moon and Mars the amorphous silicon arrays produced the highest specific power.

Collozza, Anthony J.↗

NASA NTRS1991

Design and optimization of a self-deploying PV tent array

A study was performed to design a self-deploying tent shaped PV (photovoltaic) array and optimize the design for maximum specific power. Each structural component of the design was analyzed to determine the size necessary to withstand the various forces it would be subjected to. Through this analysis the component weights were determined. An optimization was performed to determine the array dimensions and blanket geometry which produce the maximum specific power for a given PV blanket. This optimization was performed for both Lunar and Martian environmental conditions. The performance specifications for the array at both locations and with various PV blankets were determined.

Colozza, Anthony J.↗

NASA NTRS2007

Parametric Study of Biconic Re-Entry Vehicles

An optimization based on hypersonic aerodynamic performance and volumetric efficiency was accomplished for a range of biconic configurations. Both axisymmetric and quasi-axisymmetric geometries (bent and flattened) were analyzed. The aerodynamic optimization wag based on hypersonic simple Incidence angle analysis tools. The range of configurations included those suitable for r lunar return trajectory with a lifting aerocapture at Earth and an overall volume that could support a nominal crew. The results yielded five configurations that had acceptable aerodynamic performance and met overall geometry and size limitations

Steele, Bryan↗

NASA NTRS2024

Usage of ChatGPT for Engineering Design and Analysis Tool Development

ChatGPT, a generative AI large language model, has recently captured significant attention in both the computer science community and the broader public domain. It has demonstrated a wide range of capabilities, from answering simple questions to writing fully functional computer code. This study spotlights both the capabilities and limitations of ChatGPT when addressing engineering problems. The model's capacity to generate practical engineering tools is highlighted through an example of a prompt that leads to an interactive plotting tool, enabling the examination of the fluid boundary layer around a fan blade. Subsequently, the paper also uncovers potential pitfalls in ChatGPT’s application, shown through an unsuccessful attempt to use ChatGPT to automate a process in Ansys Workbench through scripting. The research further investigates ChatGPT's proficiency in addressing inquiries and providing explanations about the functionalities of OpenMDAO, an open-source, multidisciplinary design, analysis, and optimization tool developed at NASA Glenn Research Center. Finally, an optimization methodology, developed with ChatGPT’s help, is applied to the structural optimization of a fan blade. The developed optimization method utilizes T-Blade3 for geometry generation, Ansys Mechanical for meshing and finite element analysis, and sci-kit learn’s MLPRegressor method to generate a trained neural network model of the design space. OpenMDAO is then used to find the optimal point within the design space. The outcome is a significant reduction in stress in the optimized model—less than one-fifth of the stress value in the baseline model.

Design↗

NASA NTRSDate not supplied

Usage of ChatGPT for Engineering Design and Analysis Tool Development

Design↗

NASA NTRS1989

Autonomous spacecraft attitude control using magnetic torquing only

Magnetic torquing of spacecraft has been an important mechanism for attitude control since the earliest satellites were launched. Typically a magnetic control system has been used for precession/nutation damping for gravity-gradient stabilized satellites, momentum dumping for systems equipped with reaction wheels, or momentum-axis pointing for spinning and momentum-biased spacecraft. Although within the small satellite community there has always been interest in expensive, light-weight, and low-power attitude control systems, completely magnetic control systems have not been used for autonomous three-axis stabilized spacecraft due to the large computational requirements involved. As increasingly more powerful microprocessors have become available, this has become less of an impediment. These facts have motivated consideration of the all-magnetic attitude control system presented here. The problem of controlling spacecraft attitude using only magnetic torquing is cast into the form of the Linear Quadratic Regulator (LQR), resulting in a linear feedback control law. Since the geomagnetic field along a satellite trajectory is not constant, the system equations are time varying. As a result, the optimal feedback gains are time-varying. Orbit geometry is exploited to treat feedback gains as a function of position rather than time, making feasible the onboard solution of the optimal control problem. In simulations performed to date, the control laws have shown themselves to be fairly robust and a good candidate for an onboard attitude control system.

Musser, Keith L.↗

NASA NTRS2003

Optimized Shapes of Ocsillating Resonators for Generating High-Amplitude Pressure Waves

It is well known that the resonator geometry strongly influences the resonant frequencies of an acoustical resonator and the generated nonlinear standing pressure waveform. Maximizing the ratio of maximum to minimum gas pressure at an end of an oscillating resonator by optimizing the cavity contour is investigated numerically. A quasi-Newton type scheme is used to find optimized axisymmetric resonator shapes to achieve the maximum pressure compression ratio. The acoustical field is solved using a one-dimensional model, and the resonance frequency shift and hysteresis effects are obtained through an automation scheme based on continuation methods. Results are presented from optimizing cone, horn-cone, and cosine resonator geometries. Significant performance improvement is found in the optimized shapes over others previously published. Different optimized shapes are found when starting with different initial guesses, indicating multiple local extrema. The numerical model is validated by comparing with the experimental results of a horn-cone shaped resonator.

Li, Xiao-Fan↗

NASA NTRS1972

Fastening on the F-14A for cost effective fatigue resistance

Cost effectiveness airframe considerations dictated a variable geometry wing design that requires weight optimization, maximum working stress resistance and minimum fatigue concentration factors. The extensive use of titanium structural materials employed electron beam welding methods and interference fit fastening techniques as principle mechanical joining means for economic F-14A production and reliability engineering.

Beal, B. H.↗

NASA NTRS1979

Optimization of multi-layer front-contact grid patterns for solar cells

In a front-contact grid pattern for a solar cell there is a trade-off necessary between shadowing loss and excessive power loss due to voltage drop in the metalization itself. If the metalization is too little there may be excessive contact resistance to the underlying semiconductor and insufficient coverage to control losses in the thin front-surface layer of the solar cell. Optimization of grid pattern area and geometry is considered analytically to minimize total losses. Worthwhile performance advantages are shown to be possible, particularly in concentrator systems, if multi-layer grid patterns are used. The current carrying fingers should be approximately square in metal cross section and the main current feedout bars should not only be wider but also thicker than the primary collecting fingers. This is termed multi-level metalization. Effective use of multi-level grid metalization allows much greater concentration-to-loss ratio for a cell of large area and permits good performance from cells of high front-layer sheet resistance.

Flat, A.↗