Results for “friction stir processing” — Page 14

NASA NTRS2011

2014/2219 Tri-Point Crack Analysis

Friction stir welding (FSW) is a solid state welding process with potential advantages for aerospace and automotive industries dealing with light alloys. Self-reacting friction stir welding (SR-FSW) is one variation of the FSW process being developed at the National Aeronautics and Space Administration (NASA) for use in the fabrication of propellant tanks. Friction plug welding is used to seal the exit hole that remains in a circumferential SR-FSW. The objective of this study was to evaluate the deformation response at the tips of cracks located in the heat affected zone of friction plug welds and to study the fracture behavior of welds with defects in the form of fatigue cracks. The study used existing 2014-T6 to 2219-T87 self-reacting friction stir weld panels with 2219-T87 friction plug welds. Electro-discharge machined (EDM) notches were machined into the heat affected zone of the plug at the plug-to-base metal interface. Samples were then cycled to generate a fatigue crack emanating from the notch. After the fatigue crack reached a pre-defined length, a speckle pattern was applied and the ARAMIS system (a three dimensional imaging correlation system) was used to measure the deformations at the crack tip under a sequence of loads. Testing was conducted at ambient laboratory conditions. Fracture data from the testing was analyzed to evaluate residual strength capability of the panel as a function of flaw size. ARAMIS strain data was evaluated to examine strain and deformation patterns that develop around the crack tip and at the plug/weld interfaces. Four samples were used in this study, with three samples in a post-weld heat treated condition. Three samples contained large diameter plugs (M5) and one sample contained a small diameter plug (M3). Two samples were 4 inches in width and two samples were 8.5 inches in width. All samples failed through the precrack with residual strengths ranging from 37 ksi to 42 ksi.

Horton, Karla Renee↗

NASA NTRS1998

Loading Considerations for Implementing Friction STIR Welding for Large Diameter Tank Fabrication

The main objectives of the research presented here are to determine the reaction loads associated with friction stir welding (FSW) and to determine the suitability of an existing welding fixture for implementing this welding process in the fabrication of large diameter tanks. Friction stir welding is a relatively new process which is being investigated as a method for joining aluminum alloys. The aluminum-lithium alloy, Al-Li 2195, which is being used to fabricate the super-light-weight shuttle external tank has proven difficult to join using fusion techniques. Therefore, FSW and its potential applicability to joining Al-Li 2195 are of particular interest to NASA.

Adams, Glynn↗

NASA NTRS2011

Microhardness and Strain Field Characterization of Self-Reacting Friction Stir and Plug Welds of Dissimilar Aluminum Alloys

Friction stir welding (FSW) is a solid state welding process with potential advantages for aerospace and automotive industries dealing with light alloys. Self-reacting friction stir welding (SR-FSW) is one variation of the FSW process being developed at the National Aeronautics and Space Administration (NASA) for use in the fabrication of propellant tanks. Friction plug welding is used to seal the exit hole that remains in a circumferential SR-FSW. This work reports on material properties and strain patterns developed in a SR-FSW with a friction plug weld. Specifically, this study examines the behavior of a SR-FSW formed between an AA 2014-T6 plate on the advancing side and an AA 2219-T87 plate on the retreating side and a SR-FSW (AA 2014-T6 to AA 2219-T87) with a 2219-T87 plug weld. This study presents the results of a characterization of the micro-hardness, joint strength, and strain field characterization of SR-FSW and FPW joints tested at room temperature and cryogenic temperatures.

Horton, Karla Renee↗

NASA NTRS2025

Physics-Based Modeling and Simulation of Self-Reacting Friction Stir Welding Using Computational Fluid Dynamics

A physics-based model was developed to simulate the behavior of material in a self-reacting friction stir welding (SR-FSW) process for the joining of metals. This steady-state model builds upon fundamental computational fluid dynamic (CFD) principles within Ansys Fluent to solve the discretized equations. The effective viscosity is calculated using a viscoplastic model using a Sheppard-Wright formulation of flow stress. Numerous advancements have been made in the incorporated physics including (1) temperature-dependent material properties; (2) locally adaptable flow and thermal boundary conditions; and (3) adapting material properties in nugget in response to microstructural changes. Simulation strategies to accelerate computation and improve numerical stability include adapting the mesh refinement and solver relaxation factors during simulation. The result is a highly robust and computationally efficient model capable of providing the material flow and temperature history across the domain. As material history determines the local microstructure and ultimately weld strength, an accurate and detailed physics-based model has the potential to accelerate SR-FSW process development. The model is highly adaptable to changes in process parameters, tool design, or alloy.

Process Modeling↗

NASA NTRS2008

Thermal Stir Welding Development at Marshall Space Flight Center

Solid state welding processes have become the focus of welding process development at NASA's Marshall Space Flight Center. Unlike fusion weld processes such as tungsten inert gas (TIG), variable polarity plasma arc (VPPA), electron beam (EB), etc., solid state welding processes do not melt the material during welding. The resultant microstructure can be characterized as a dynamically recrystallized morphology much different than the casted, dentritic structure typical of fusion weld processes. The primary benefits of solid state processes over fusion weld processes include superior mechanic properties and the elimination of thermal distortion and residual stresses. These solid state processes attributes have profoundly influenced the direction of advanced welding research and development within the NASA agency. Thermal Stir Welding (TSW) is a new solid state welding process being developed at the Marshall Space Flight Center. Unlike friction stir welding, the heating, stirring and forging elements of the weld process can be decoupled for independent control. An induction coil induces energy into a workpiece to attain a desired plastic temperature. An independently controlled stir rod, captured within non-rotating containment plates, then stirs the plasticized material followed by forging plates/rollers that work the stirred weld joint. The independent control (decoupling) of heating, stirring and forging allows, theoretically, for the precision control of microstructure morphology. The TSW process is being used to evaluate the solid state joining of Haynes 230 for ARES J-2X applications. It is also being developed for 500-in (12.5 mm) thick commercially pure grade 2 titanium for navy applications. Other interests include Inconel 718 and stainless steel. This presentation will provide metallurgical and mechanical property data for these high melting temperature alloys.

Ding, Robert J.↗

DOE OSTI2024

Nuclear Energy Critical Material Waste Minimization Enabled by AM Techniques

This project provides evidence of the successful recycling of solid waste offcuts resulting from conventional manufacturing processes from three relevant alloys to next-generation nuclear reactor developers, providing a potentially upscalable circular process where no critical elements will be lost. Furthermore, iMOF-based adsorbents were successfully designed for CM extraction from aqueous solution, thereby providing a pathway for future upscaling for salvaging dissolved Ni ions. This research has achieved its goal of showing the impact of novel applications of recycling technologies for solid and liquid wastes that can be upscaled for application.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

NASA NTRS2011

Investigation of Microstructure and Microhardness in Self-Reacting Friction Stir Welded AA2014-T6 and AA2219-T87

Friction stir welding (FSW) is a solid state welding process with potential advantages for aerospace and automotive industries dealing with light alloys. Self-reacting friction stir welding (SR-FSW) is one variation of the FSW process being developed at the National Aeronautics and Space Administration (NASA) for use in the fabrication of propellant tanks. This work reports on the microstructure and microhardness of SR-FSW between two dissimilar aluminum alloys. Specifically, the study examines the cross section of the weld joint formed between an AA2014-T6 plate on the advancing side and an AA2219-T87 plate on the retreating side. The microstructural analysis shows an irregularly displaced weld seam from the advancing side past the thermo-mechanical affected zone (TMAZ) into the weld nugget region. There are sharp variations in the microhardness across the weld. These variations are described in the paper and mechanisms for their formation are discussed.

Horton, K. Renee↗

NASA NTRS2016

Friction Stir Welding and NASA

Friction stir welding (FSW) is a solid state welding process with potential advantages for aerospace and automotive industries dealing with light alloys. Self-reacting friction stir welding (SR-FSW) is one variation of the FSW process being developed at the National Aeronautics and Space Administration (NASA) for use in the fabrication of propellant tanks and other areas used on the Space Launch System (SLS) NASA's SLS is an advanced, heavy-lift launch vehicle which will provide an entirely new capability for science and human exploration beyond Earth's orbit. The SLS will give the nation a safe, affordable and sustainable means of reaching beyond our current limits and open new doors of discovery from the unique vantage point of space This talk will elaborate on the SR-FSW process and it's usage on the current Space Launch System Program at NASA.

Horton, K Renee↗

DOE OSTI2023

A High-Speed Rotational Diamond Anvil Cell for In Situ Analysis of Hierarchical Microstructural Evolution of Metallic Alloys during Extreme Shear Deformation

High speed shear deformation is ubiquitous in engineering applications, ranging from material processing methods such as friction stir processing/extrusion and in tribological contacts. However, analyzing the microstructural evolution of materials while they are undergoing high speed shear deformation have been a long-standing challenge. This led to predominant reliance on ex situ microscopy before and after shear deformation. But ex situ microscopy lacks the ability to analyze dynamic and transient hierarchical microstructural evolution mechanisms that could occur during shear deformation of materials. Therefore, to better understand the dynamic mechanisms of mass and energy transfer in materials under shear deformation, we developed a first of its kind high-speed rotational diamond anvil cell (HS-RDAC) for synchrotron-based in situ high-energy x-ray diffraction (XRD). We studied the time resolved lattice strain evolution, XRD peak broadening and changes in spatial variation of shear deformation induced alloying in pure metal and metal alloy sheets and powder mixture using the HS-RDAC. These in situ results were combined with detailed ex situ microstructural characterization before and after the shear deformation using transmission electron microscopy and atom probe tomography, which revealed the different stages of evolution of a shear deformation induced hierarchical nanostructure. Multiscale computational simulations including computational fluid dynamics, crystal plasticity, molecular dynamic simulation and density functional theory uncovered the mechanisms behind morphological changes, evolution of defect structures and changes in driving force for shear deformation induced intermixing. In conclusion, this in situ HS-RDAC capability, in combination with ex situ microstructural characterization and computational simulations, can provide new insights into the hierarchical microstructural evolution pathway during shear deformation.

36 MATERIALS SCIENCE↗

NASA NTRS2012

Friction-Stir-Welded and Spin-Formed End Domes for Cryogenic Tanks

Manufacturing of single-piece end domes for cryogenic tanks employing spin forming of tailored, friction-stir-welded blanks of Al-Li alloy 2195 plate offers cost and reliability benefits. The introduction of plastic deformation into a friction stir weld is a unique feature of the proposed manufacturing route. This investigation addressed abnormal grain growth [AGG] within the friction stir weldments during postfabrication processing of a prototype dome. The phenomenon of AGG was observed during the solution heat treatment [SHT] phase of T8 tempering and is a major concern for meeting specifications. Such abrupt microstructural transitions can be detrimental to notch-sensitive mechanical properties, such as ductility and/or fracture toughness. If the issue of AGG cannot be resolved, then the acceptance of this approach as a viable manufacturing route may be in jeopardy. The innovative approach adopted in this investigation was the insertion of a stand-alone, Intermediate Annealing Treatment [IAT] between the spin forming and T8 processing operations. A simple, recovery annealing step was deemed to be the most readily-scalable solution when fabricating thin-walled, ellipsoidal domes. The research effort culminated in the development of an effective IAT, which resulted in a significant decrease in AGG following SHT. The processing philosophy adopted in designing the IAT is outlined and the microstructural reasons for success are discussed. The analytical results presented are consistent with promoting continuous grain growth during the IAT, thereby suppressing AGG during the SHT.

Hales, S. J.↗

DOE OSTI2018

Friction Stir Scribe Joining of Carbon Fiber Reinforced Polymer (CFRP) to Aluminum

The purpose of this project was to develop the critical process technology, models, and tools necessary to advance the Friction Stir Scribe, FSS, joining method through experimentation, validation at the laboratory scale, and integration into a production-like robotic environment. Implementation of FSS technology for joining polymer composites to metals will enable greater use of lightweight materials by providing technology capable of joining linear configurations without the use of adhesives or other third-body fasteners by creating an in-situ joint from the parent materials. As FSS technology provides the capability to join multi-material structures on robotic platforms using linear configurations, the development of this technology for use on the BIW will impact a great diversity of CFRP joints within the vehicle; thus, allowing a greater reduction in vehicle mass through more specifically designed structures. The FSS process has been developed to include integration of the FSS tool with a stationary shoulder, which has been shown to be required to achieve the desired surface quality (i.e., crown flash level). However, the targeted joint strength has not been achieved because the resulting stirred CFRP microstructure does not provide similar performance as the as-molded composite leading to low fracture strengths despite our efforts investigating various unique alternative approaches. In support of the experimental work, a process-structure model was developed and validated for the FSS joining (FSSJ) process using surrogate materials (steel and Al). The cyclic corrosion testing of the FSS joints and self-piercing riveted (SPR) joints revealed different modes of galvanic corrosion in the two types of joints. The SPR samples exhibited a greater amount of corrosion on the external surfaces. The presence of steel rivets in these joints exacerbated the situation, with the rivets getting preferentially corroded. The FSSJ samples despite exhibiting less surface corrosion, exhibited severe corrosion under the joint overlap area.

36 MATERIALS SCIENCE↗

DOE OSTI2024

NuMI/LBNF Horn and Stripline Welding

Focusing horns for secondary particles are critical components for creating a stable beam of neutrinos. These components need to survive in a harsh environment and withstand high stresses. Extending the lifetime of the horns is critical as spare fabrication takes approximately two years and has many subcomponents with strict quality control. Two key aspects of the fabrication process include the inner conductor CNC TIG welding and the friction stir welding of the stripline pieces. The process for welding requires steps such as sample welding, x-ray imaging, and tensile pull tests. Having a perfect weld retains as much of the original strength of the base metal and reduces the risk of failure. As FNAL ramps up in power to 2.4MW, the lifetime of the horn and stripline will more heavily rely on continuing to have high quality welding procedures and thorough quality assurance.

Orea, Adrian↗

DOE OSTI2018

Influence of Welding Combined Plastic Forming on Microstructure Stability and Mechanical Properties of Friction Stir-Welded Al-Cu Alloy

A new tailor-welded process, which combines stages of welding, plastic forming, and heat treatment strengthening, was developed to produce a friction stir-welded (FSW) Al-alloy joint. The Al-Cu sheets were FSW under different welding parameters and then were plastic-deformed. The microstructural evolution and mechanical properties of the FSW joint were investigated by scanning electron microscopy and tensile tests. It was found that high heat input during FSW and low solution temperature suppress the abnormal grain growth (AGG) of the joint due to the differential in grain size and grain boundary energy. The microstructure heterogeneity of the FSW joint is effectively improved, as no AGG occurs. The retention of fine equiaxed grains and the increase in the density of precipitates result in excellent mechanical properties. The increase in the strength and micro-hardness of the joint mainly depends on the plastic deformation prior to aging treatment.

36 MATERIALS SCIENCE↗

NASA NTRS2010

Development of Weld Inspection of the Ares I Crew Launch Vehicle Upper Stage

NASA is designing a new crewed launch vehicle called Ares I to replace the Space Shuttle after its scheduled retirement in 2010. This new launch vehicle will build on the Shuttle technology in many ways including using a first stage based upon the Space Shuttle Solid Rocket Booster, advanced aluminum alloys for the second stage tanks, and friction stir welding to assemble the second stage. Friction stir welding uses a spinning pin that is inserted in the joint between two panels that are to be welded. The pin mechanically mixes the metal together below the melting temperature to form the weld. Friction stir welding allows high strength joints in metals that would otherwise lose much of their strength as they are melted during the fusion welding process. One significant change from the Space Shuttle that impacts NDE is the implementation of self-reacting friction stir welding for non-linear welds on the primary metallic structure. The self-reacting technique differs from the conventional technique because the load of the pin tool pressing down on the metal being joined is reacted by a nut on the end of the tool rather than an anvil behind the part. No spacecraft has ever flown with a self-reacting friction stir weld, so this is a major advancement in the manufacturing process, bringing with it a whole new set of challenges for NDE to overcome. The metal microstructure and possible defects are different from other weld processes. Friction plug welds will be used to close out the hole remaining in the radial welds when friction stir welded. This plug welding also has unique challenges in inspection. The current state of development of these inspections will be presented, along with other information pertinent to NDE of the Ares I.

Russell, Sam↗

DOE OSTI2024

Breaking Boundaries: Deformation Processing Techniques for the Next Generation of Lightweight and High-Strength Materials

This chapter emphasizes the importance of solid phase processing (SPP) techniques in developing advanced materials for lightweight and high-strength applications. SPP methods like friction stir welding, and shear-assisted processing can create new microstructures and process materials in novel ways. SPP can enhance mechanical performance via various strengthening mechanisms like solid solution supersaturation, Hall-Petch and Orowan effects, and misorientation angle grain boundaries. The potential for in situ alloying or joining of components with near-net shape and low energy inputs, even for immiscible systems with high enthalpies of mixing, is also discussed. The chapter explores the concept of metastability through microstructural manipulation and the role of advanced characterization for atomistic understanding. The formation of metastable grain, shear-driven chemical mixing, and transformation pathways are also discussed. Finally, the emerging trends for SPP and the challenges that need to be addressed before realizing the full potential of these techniques are presented.

Lastovich, Michael↗

DOE OSTI2024

Chloride-Induced Stress Corrosion Cracking of Friction Stir-Welded 304L Stainless Steel: Effect of Microstructure and Temperature

Dry storage canisters of used nuclear fuels are fabricated using SUS 304L stainless steel. Chloride-induced stress corrosion cracking (CISCC) is one of the major failure modes of dry storage canisters. The cracked canisters can be repaired by friction stir welding (FSW), a low-heat input ‘solid-phase’ welding process. It is important to evaluate the ClSCC resistance of the friction stir welded material. Stress corrosion cracking (SCC) studies were carried out on mill-annealed base materials and friction stir welded 304L stainless U-bend specimens in 3.5% NaCl + 5 N H2SO4 solution at room temperature and boiling MgCl2 solution at 155 °C. The engineering stress on the outer fiber of the FSW U-bend specimen was ~60% higher than that of the base metal (BM). In spite of the higher stress level of the FSW, both materials (FSW and BM) showed almost similar SCC failure times in the two different test solutions. The SCC occurred in the thermo-mechanically affected zone (TMAZ) of the FSW specimens in the 3.5% NaCl + 5 N H2SO4 solution at room temperature, while the stirred zone (SZ) was relatively crack-free. The failure occurred at the stirred zone when tested in the boiling MgCl2 solution. Hydrogen reduction was the cathodic reaction in the boiling MgCl2 solution, which promoted hydrogen-assisted cracking of the heavily deformed stirred zone. The emergence of the slip step followed by passive film rupture and dissolution of the slip step could be the SCC events in the 3.5% NaCl + 5 N H2SO4 solution at room temperature. However, the slip step height was not sufficient to cause passivity breakdown in the fine-grained SZ. Therefore, the SCC occurred in the partially recrystallized softer TMAZ. Overall, the friction-stirred 304L showed higher tolerance to ClSCC than the 304L base metal.

304L austenitic stainless steel↗

DOE OSTI2018

ADVANCED WELDING TECHNOLOGY DEVELOPMENT FOR NUCLEAR REACTOR REPAIR

Welding is widely used for repair, maintenance, and upgrade of nuclear reactor components. As a critical technology for supporting the extension of nuclear power plant service lifetimes beyond 60 years, there has been an industry need in further developing welding technology for highly irradiated materials. During welding of irradiated materials, Helium, which is a transmutation byproduct from Boron and Nickel contained in the structural alloys, can coalesce into bubbles along grain boundaries in the material under driving forces of high temperature and thermal tensile stress. This leads to embrittlement and potential intergranular cracking in the Heat Affected Zone (HAZ) of the weld. In this paper, irradiated 304 stainless steel coupons containing 5, 10 and 20 ppm Boron prior to radiation were successfully welded by advanced laser beam welding (LBW) and friction stir welding (FSW). Facilities and welding machine design, welding processes development, cold material welded joints evaluation, process safety control and documentation, and irradiated material welding are discussed. Both laser and friction stir welded coupons of the irradiated material exhibited high welding quality and surface finish. No Helium induced welding defects were observed on the weld surfaces or adjacent base metals.

Tang, Wei↗

DOE OSTI2019

Adaptive relay autotuning under static and non-static disturbances with application to friction stir welding

When a traditional relay feedback test is biased, asymmetry is induced, erroneous system identification occurs, and the test may stop oscillating. Adaptive methods which restore symmetry to the relay test are developed, and additional methods are presented to detect and recover from a non-oscillation condition. This is demonstrated both in simulation and in a process with significant transients and disturbances - friction stir welding (FSW). In testing, it is shown that the adaptive method is able to restore symmetry even in the presence of severe and changing disturbances, including after the weld plunge where temperature gradients change rapidly. Finally, these improvements enable system identification of systems such as FSW in a more robust and accurate manner.

42 ENGINEERING↗