Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flow reactor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Autoignition measurements and a validated kinetic model for the biodiesel surrogate, methyl butanoate

The autoignition of methyl butanoate has been studied at 1 and 4 atm in a shock tube over the temperature range 1250-1760 K at equivalence ratios of 1.5, 1.0, 0.5, and 0.25 at fuel concentrations of 1.0 and 1.5%. These measurements are complemented by autoignition data from a rapid compression machine over the temperature range 640-949 K at compressed gas pressures of 10, 20, and 40 atm and at varying equivalence ratios of 1.0, 0.5, and 0.33 using fuel concentrations of 1.59 and 3.13%. The autoignition of methyl butanoate is observed to follow Arrhenius-like temperature dependence over all conditions studied. These data, together with speciation data reported in the literature in a flow reactor, a jet-stirred reactor, and an opposed-flow diffusion flame, were used to produce a detailed chemical kinetic model. It was found that the model correctly simulated the effect of change in equivalence ratio, fuel fraction, and pressure for shock tube ignition delays. The agreement with rapid compression machine ignition delays is less accurate, although the qualitative agreement is reasonable. The model reproduces most speciation data with good accuracy. In addition, the important reaction pathways over each regime have been elucidated by both sensitivity and flux analyses. (author)

09 BIOMASS FUELS↗

Catalytic Upgrading of Renewable Feedstock (Final Technical Report)

The goal of this DOE-funded project was to investigate the fundamental science related to the development of homogeneous (de)hydrogenation catalysts in order to enable energy-relevant transformations of bio-relevant chemical feedstocks including ethanol. The primary focus was to improve the activity of ethanol upgrading catalysts, specifically informed through mechanistic studies, in order to enable rational design optimization strategies. Following in depth mechanistic studies, targeted reaction optimization approaches included ligand redesign to improve catalyst stability, developing new carbon-carbon bond forming reactions using ethanol as a precursor, and examining photochemically-mediated reactions, ultimately to integrate within other reactor designs such as continuous flow reactors. The high modularity of the catalyst components (ligands) has enabled the preparation and analyses of multiple catalyst precursors. These studies uncovered an unexpectedly beneficial substitution pattern of the ligand structure that led to the development of new catalysts that are the best in class for upgrading ethanol to butanol with a turnover number of 155,890 and a turnover frequency of 12,690 h –1 . In addition to upgrading ethanol to butanol, cascade reaction sequences were developed to form new C-C bonds using ethanol as a bio-relevant feedstock, providing access to platform chemicals from renewable sources. As part of the reaction discovery process, new mechanistic details were uncovered that provided insights into: a) catalyst speciation, b) decomposition pathways, c) carbon monoxide releasing pathways, and d) carbon-carbon and carbon hydrogen bond breaking pathways. Most of these outcomes were previously not known; however, they provide important directions for new catalyst design strategies. Finally, use of high throughput and in situ photochemical reaction analyses enabled detailed studies into changes to the catalyst structure upon irradiation. Irradiation was found to improve hydrogen transfer catalysis, by promoting a ligand dissociation event.

09 BIOMASS FUELS↗

Development of a model and computer code to describe solar grade silicon production processes

Mathematical models, and computer codes based on these models were developed which allow prediction of the product distribution in chemical reactors in which gaseous silicon compounds are converted to condensed phase silicon. The reactors to be modeled are flow reactors in which silane or one of the halogenated silanes is thermally decomposed or reacted with an alkali metal, H2 or H atoms. Because the product of interest is particulate silicon, processes which must be modeled, in addition to mixing and reaction of gas-phase reactants, include the nucleation and growth of condensed Si via coagulation, condensation, and heterogeneous reaction.

Srivastava, R.↗

Controlling product selectivity in hybrid gas/liquid reactors using gas conditions, voltage, and temperature

For the conversion of CO 2 into fuels and chemical feedstocks, hybrid gas/liquid-fed electrochemical flow reactors provide advantages in selectivity and production rates over traditional liquid phase reactors. However, fundamental questions remain about how to optimize conditions to produce desired products. Here, using an alkaline electrolyte to suppress hydrogen formation and a gas diffusion electrode catalyst composed of copper nanoparticles on carbon nanospikes, we investigate how hydrocarbon product selectivity in the CO 2 reduction reaction in hybrid reactors depends on three experimentally controllable parameters: (1) supply of dry or humidified CO 2 gas, (2) applied potential, and (3) electrolyte temperature. Changing from dry to humidified CO 2 dramatically alters product selectivity from C 2 products ethanol and acetic acid to ethylene and C 1 products formic acid and methane. Water vapor evidently influences product selectivity of reactions that occur on the gas-facing side of the catalyst by adding a source of protons that alters reaction pathways and intermediates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of a plant-wide dynamic model of an integrated gasification combined cycle (IGCC) plant

In this presentation, development of a plant-wide dynamic model of an advanced Integrated Gasification Combined Cycle (IGCC) plant with CO2 capture will be discussed. The IGCC reference plant generates 640 MWe of net power using Illinois No.6 coal as the feed. The plant includes an entrained, downflow, General Electric Energy (GEE) gasifier with a radiant syngas cooler (RSC), a two-stage water gas shift (WGS) conversion process, and two advanced 'F' class combustion turbines partially integrated with an elevated-pressure air separation unit (ASU). A subcritical steam cycle is considered for heat recovery steam generation. Syngas is selectively cleaned by a SELEXOL acid gas removal (AGR) process. Sulfur is recovered using a two-train Claus unit with tail gas recycle to the AGR. A multistage intercooled compressor is used for compressing CO2 to the pressure required for sequestration. Using Illinois No.6 coal, the reference plant generates 640 MWe of net power. The plant-wide steady-state and dynamic IGCC simulations have been generated using the Aspen Plus{reg_sign} and Aspen Plus Dynamics{reg_sign} process simulators, respectively. The model is generated based on the Case 2 IGCC configuration detailed in the study available in the NETL website1. The GEE gasifier is represented with a restricted equilibrium reactor model where the temperature approach to equilibrium for individual reactions can be modified based on the experimental data. In this radiant-only configuration, the syngas from the Radiant Syngas Cooler (RSC) is quenched in a scrubber. The blackwater from the scrubber bottom is further cleaned in the blackwater treatment plant. The cleaned water is returned back to the scrubber and also used for slurry preparation. The acid gas from the sour water stripper (SWS) is sent to the Claus plant. The syngas from the scrubber passes through a sour shift process. The WGS reactors are modeled as adiabatic plug flow reactors with rigorous kinetics based on the mid-life activity of the shift-catalyst. The SELEXOL unit consists of the H2S and CO2 absorbers that are designed to meet the stringent environmental limits and requirements of other associated units. The model also considers the stripper for recovering H2S that is sent as a feed to a split-flow Claus unit. The tail gas from the Claus unit is recycled to the SELEXOL unit. The cleaned syngas is sent to the GE 7FB gas turbine. This turbine is modeled as per published data in the literature. Diluent N2 is used from the elevated-pressure ASU for reducing the NOx formation. The heat recovery steam generator (HRSG) is modeled by considering generation of high-pressure, intermediate-pressure, and low-pressure steam. All of the vessels, reactors, heat exchangers, and the columns have been sized. The basic IGCC process control structure has been synthesized by standard guidelines and existing practices. The steady-state simulation is solved in sequential-modular mode in Aspen Plus{reg_sign} and consists of more than 300 unit operations, 33 design specs, and 16 calculator blocks. The equation-oriented dynamic simulation consists of more than 100,000 equations solved using a multi-step Gear's integrator in Aspen Plus Dynamics{reg_sign}. The challenges faced in solving the dynamic model and key transient results from this dynamic model will also be discussed.

97 MATHEMATICS AND COMPUTING↗

Pyrolysis of aseptic packages (tetrapak) in a laboratory screw type reactor and secondary thermal/catalytic tar decomposition

Highlights: ► Pyrolysis of aseptic packages was carried out in a laboratory flow reactor. ► Distribution of tetrapak into the product yields was obtained. ► Composition of the pyrolysis products was estimated. ► Secondary thermal and catalytic decomposition of tars was studied. ► Two types of catalysts (dolomite and red clay marked AFRC) were used. - Abstract: Pyrolysis of aseptic packages (tetrapak cartons) in a laboratory apparatus using a flow screw type reactor and a secondary catalytic reactor for tar cracking was studied. The pyrolysis experiments were realized at temperatures ranging from 650 °C to 850 °C aimed at maximizing of the amount of the gas product and reducing its tar content. Distribution of tetrapak into the product yields at different conditions was obtained. The presence of H{sub 2}, CO, CH{sub 4}, CO{sub 2} and light hydrocarbons, HCx, in the gas product was observed. The Aluminum foil was easily separated from the solid product. The rest part of char was characterized by proximate and elemental analysis and calorimetric measurements. The total organic carbon in the tar product was estimated by elemental analysis of tars. Two types of catalysts (dolomite and red clay marked AFRC) were used for catalytic thermal tar decomposition. Three series of experiments (without catalyst in a secondary cracking reactor, with dolomite and with AFRC) at temperatures of 650, 700, 750, 800 and 850 °C were carried out. Both types of catalysts have significantly affected the content of tars and other components in pyrolytic gases. The effect of catalyst on the tetrapack distribution into the product yield on the composition of gas and on the total organic carbon in the tar product is presented in this work.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Simplified Numerical Approach to Characterize the Thermal Response of a Moving Bed Solar Reactor

Abstract Concentrated solar thermochemical storage in the form of a zero-emission fuel is a promising option to produce long-duration energy storage. Solar fuel is produced using a cavity reactor that captures concentrated solar radiation from a solar field of heliostats. In this paper, heat transfer model of a tubular plug-flow reactor designed and manufactured for a solar fuel production is presented. Experimental data collected from a fixed bed tubular reactor testing are used for model comparison. The system consists of an externally heated tube with counter-current flowing gas and moving solid particles as the heated media. The proposed model simulates the dynamic behavior of temperature profiles of the tube wall, gas, and particles under various gas flowrates and residence times. The heat transfer between gas–wall, solid particle–wall, and gas–solid particle is numerically studied. The model results are compared with the results of experiments done using a 4 kW furnace with a 150 mm heating zone surrounding a horizontal alumina tube (reactor) with 50.8 mm outer diameter and thickness of 3.175 mm. Solid fixed particles of magnesium manganese oxide (MgMn2O4) with the size of 1 mm are packed within the length of 250 mm at the center of the tube length. Simulation results are assessed with respect to fixed bed experimental data for four different gas flowrates, namely, 5, 10, 15, and 20 standard liters per minute of air, and furnace temperatures in the range of 200–1200 °C. The simulation results showed good agreement with maximum steady state error that is less than 6% of those obtained from the experiments for all runs. The proposed model can be implemented as a low-order physical model for the control of temperature inside plug-flow reactors for thermochemical energy storage applications.

Engineering↗

Comparison of uranium(VI) removal by Shewanella oneidensis MR-1 in flow and batch reactors

To better understand the interactions among metal contaminants, nutrients, and microorganisms in subsurface under fracture-flow conditions, iron-reducing biofilms (pure cultures of Shewanella oneidensis MR-1) were grown in six fracture flow reactors (FFRs) of different geometries. The spatial and temporal distribution of nutrients, contaminant, and bacteria were examined using a tracer dye (brilliant blue FCF) and microscopy. The results showed that plugging by bacterial cells depended on the geometry of the reactor; and iron-reducing biofilms grown in FFRs had a definite U(VI)-reduction capacity. To find out the U(VI)-reduction capacity of iron-reducing biofilms, batch experiments of U(VI) reduction were performed in repetitive addition mode. U(VI)-reduction rates of stationary phase grown iron-reducing cultures with and without spent medium decreased after each U(VI) addition. At the end of the fourth U(VI)-addition, stationary phase iron-reducing cultures treated with U(VI) with and without spent medium yielded grey and black precipitates, respectively. These grey and black U precipitates were analyzed using High Resolution-Transmission Electron Microscopy, Energy-dispersive X-ray spectroscopy, and X-ray diffraction. Data for randomly selected area of black and grey U precipitates showed that reduced U particles (3-6 nm) were crystalline and amorphous in nature, respectively. This information obtained in this study could be used to develop substrate addition strategies for metal immobilization in subsurface fracture flow systems.

54 ENVIRONMENTAL SCIENCES↗

Effects of water addition on the combustion of iso -octane investigated in laminar flames, low-temperature reactors, and an HCCI engine

In this work, the effect of H 2 O injection on the combustion process of iso -octane was investigated with the aim to better understand the suitability of water addition as a potential engine control parameter for homogeneous-charge compression ignition (HCCI) combustion. Several experiments were combined including premixed low-pressure flames, a jet-stirred reactor (JSR) and a plug-flow reactor (PFR), both at atmospheric pressure, and a single-cylinder research engine (SCRE) operated with either iso -octane or RON 98 gasoline. The thermal effect of H 2 O addition was determined in laminar premixed iso -octane/O 2 /Ar flames (equivalence ratio $Φ$=1.4, 40 mbar) with H 2 O mole fractions of 0 to 0.22, where water addition reduced the temperature measured by laser-induced fluorescence (LIF) by up to 110 K. Speciation data were obtained from these flames as well as in the JSR ($Φ$=0.65, 933 mbar) and PFR experiments ($Φ$=0.65, 970 mbar) with and without H 2 O addition in the low- to intermediate temperature regime from 700–1100 K. The chemical analysis in these flame and reactor experiments was performed using molecular-beam mass spectrometry (MBMS) employing either electron ionization (EI) in the PFR and premixed flame or single-photon ionization (PI) by tunable vacuum-ultraviolet radiation in the JSR. The effects on species mole fractions were small which is supported by predictions from chemical-kinetic simulations. Quantitative speciation data of the exhaust gas of the SCRE were obtained by using Fourier-transform infrared (FTIR) spectroscopy. A very similar species pool was detected in the laboratory-scale experiments and for the engine operation. It is thus assumed that these results could assist in guiding both the improvement of fundamental chemical-kinetic as well as HCCI engine control models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Kinetic modelling of an environmentally friendly carbamazepine synthesis via urea and iminostilbene in batch and continuous processes

Accurate kinetic models for reaction systems allow for improved process understanding and greater quality control, which is particularly beneficial as the pharmaceutical industry shifts from batch to continuous manufacturing (CM). In this work, a first principles kinetic model has been developed for the synthesis of carbamazepine (CBZ) from iminostilbene and urea, starting in a batch reactor and subsequently in a continuous flow reactor. An eco-friendly reaction pathway using urea was selected to avoid the toxic reagents that are typically used for synthesis of CBZ. The kinetic parameters determined from batch reactions were utilized in a MATLAB based kinetic model to simulate the yield for the continuous process. Overall, good agreement between the model prediction and corresponding experimental values was observed for the batch and continuous reaction systems within the full factorial design space. However, the model slightly overpredicted the yield of the continuous reaction system for higher conversion values (>60%) since it did not account for the reverse reaction that can occur at the studied reaction conditions. Here, the use of broken order kinetics was compared with whole number orders, and it was determined that the whole number orders resulted in better agreement at all conversion values for the continuous system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ediesel: Diesel Additive production from ethanol and bio-diesel coproducts

This project has focused on supporting and expanding the U.S. ethanol industry by developing new conversion routes and products from ethanol and the byproducts made in ethanol fermentation. The work is relevant to the DOE program goals of developing high-margin chemical products in the biorefinery to economically support large-scale biofuel production. The higher alcohols from condensation of ethanol, alkylated amine compounds made by electrocatalytic alkyation, and fusel alcohols produced by modified fermentation microorganisms are all existing or potentially large-scale commodity or specialty chemicals with well-defined uses in industry. The formation of higher alcohols from ethanol in the condensed phase developed several catalysts, first in stirred batch autoclave reactors and then in a continuous flow reactor system, to achieve significant yields of n-butanol and higher alcohols. The best selectivity to higher alcohols exceeded 80% of theoretical at ethanol conversions of 30-40%. From the laboratory experiments and analysis of the phase equilibria of the species involved, a process concept was generated and simulated in AspenPlus to determine the specifications of the various equipment involved in the process. Results show that for the conversion and selectivity described above, the required n-butanol selling price of ~$1.60/kg is in the range of current n-butanol selling price in the marketplace. Several additional permutations of the process, along with evaluation of higher conversion and selectivities to desired alcohol products, showed that the production of n-butanol from ethanol should be competitive in the marketplace as the science and engineering behind the process improves with continued development. A second aspect of the project focused on producing fusel alcohols in increased quantities during ethanol fermentation. Fusel alcohols, which are composed primarily of isoamyl alcohol and minor quantities of C3-C6 alcohols, have potential as higher value feed stocks for specialty chemical production. Several strains of yeast were evaluated for fusel alcohol production, and the most efficient process for separating and purifying fusel alcohols was developed from both experiments and simulation. Finally, model fusel alcohol mixtures were subjected to condensation reactions with ethanol to prepare higher alcohols that again have potential for specialty chemical or solvent applications. In this preliminary work, measurable quantities of several species were observed, including some species that were previously unknown or uncharacterized in the literature. The third aspect of the project involved the electrocatalytic alkylation of amines with alcohols to form alkyl amines. Ethanol has been demonstrated to serve as an effective ethyl group transfer agent to the nitrogen centers of amines, a reaction with only water as a byproduct. Mild reaction conditions (60 °C, aqueous solution) are enabled by the novel use of simple, undivided electrochemical cell reactors that include long-lived, low cost catalytic electrodes. Direct polyalkylation of ammonia and isolation of the resulting triethylamine product was readily achieved in high yield. Though classical high temperature and pressure industrial scale alkylations reactions will likely continue to be used for production of simple product such as triethylamine, this approach has opened the door to the low cost, low waste use of ethanol and related primary and secondary alcohols to alkylate more delicate amines that were heretofore difficult to synthesize.

02 PETROLEUM↗

An Open-Source Framework for the Computational Analysis and Design of Autothermal Chemical Processes

The main project object was to develop software tools for simulating non-equilibrium autothermal processes, improving the prospects for identifying and designing such systems. The project demonstrates the use of these tools to simulate autothermal pyrolysis, a process recently developed at the pilot-plant scale at Iowa State University. In such process, instead of externally heating a reactor to pro-vide the enthalpy of pyrolysis, sufficient oxygen in the form of air is introduced into the reactor to support partial oxidation of reactants and products with the exothermic energy released supporting endothermic pyrolysis reactions. A fluidized bed is used to assure good mixing of biomass and oxidant and provide an isothermal reaction environment. The amount of oxygen required depends upon the kind of biomass being pyrolyzed and parasitic heat losses from the reactor. For example, for woody biomass pyrolyzed under conditions that simulate adiabatic operation, equivalence ratios can be as low as 0.06, compared to 0.20 or higher for autothermal gasifiers. By removing the heat transfer bottleneck of conventional pyrolysis, operation in autothermal mode allowed a significant increase in reactor throughput process, approaching five times the throughput of the conventionally operated pyrolyzer. Different simulation strategies were considered and developed: a zero-dimensional chemistry model was used to verify the applicability of kinetic schemes to predict biomass fast pyrolysis in autothermal conditions. Conventional chemical reactor models such as the plug flow reactor and the partially stirred reactor were used to investigate the role of mixing in the fluidized bed pyrolyzer and to establish the impact of mixing time on the gas-phase reactions. A comprehensive multiphase computational fluid dynamics (mCFD) framework, including polydisperse granular phase modeling and detailed chemical kinetics was formulated and used to model the experimental setup for autothermal biomass fast pyrolysis at ISU. Multiphase CFD was also used to investigate the role of biomass feed positioning on the mixing of biomass in the pyrolizer. Finally, a reduced order model (ROM), suitable to be implemented in process simulators was obtained. Both the mCFD and the ROM were validated against experiments.

09 BIOMASS FUELS↗

Systems and methods of making carbon nanotubes

A method of producing a carbon nanotube may include heating a convergent flow nozzle and a flow chamber of a carbon nanotube reactor, flowing a vaporized reactant stream through the nozzle and collecting a carbon nanotube product from an outlet of a heated flow chamber disposed downstream of the heated convergent flow nozzle. The vaporized reactant stream may include a carbon nanotube nucleation carbon source, a carbon nanotube growth carbon source, and a carbon nanotube catalyst precursor. The nozzle may have a nozzle contraction ratio of from 3:1 to 300:1.

Wang, Yuhuang↗

Chemical Reactor Network Modeling of Ammonia Rich-Quench-Lean Combustion Using a Partially Stirred Reactor Approach

Ammonia is a promising alternative to hydrogen with high energy density and favorable storage and transport characteristics. However, low flammability and a propensity for high nitrogen oxide (NO x ) emissions make direct utilization challenging. Recently, two-stage rich-quench-lean (RQL) combustion strategies have shown promise in achieving low NO x emissions with ammonia. In this approach, the rich stage serves to oxidize a portion of the fuel while thermally decomposing as much of the remaining ammonia as possible, generating hydrogen. In the second (lean) stage, air is rapidly introduced, burning out the hydrogen and residual ammonia. Two-stage RQL combustion of ammonia has been investigated in the open literature both experimentally and numerically. In general, idealized chemical reactor network (CRN) models predict NO x concentrations below those of 2D/3D computational fluid dynamics models and experiments. The primary drivers of these discrepancies may be largely attributed to finite rate mixing nonadiabatic operation. The typical CRN model is comprised of a perfectly-stirred-reactor (PSR), followed by a plug-flow-reactor (PFR), meant to represent the flame, and postflame zones, respectively. In the two-stage RQL approach two PSR-PFR networks are arranged sequentially, corresponding to the rich and lean stages, with secondary air injection in between. In the authors' past work, this arrangement has demonstrated the significant sensitivity of exit NO x to the rich stage equivalence ratio, while the amount of secondary air injection was shown to be less critical. In this paper, the CRN model is extended to (1) include the impacts of heat loss and (2) utilize a partially-stirred-reactor (PaSR) approach to study the impacts of mixing on emissions performance. Varying amounts of heat loss are applied to the rich relaxation zone to understand emissions performance and changes to optimization of equivalence ratio and residence time. Premixed and nonpremixed configurations are considered in the rich stage PaSR, with varying degrees of mixing intensity to study the interaction between mixing, transport, and kinetic timescales. Critically, the impact of mixing between hot products and secondary air injection is studied to understand practical injector needs. Results show unburnt ammonia leaving the rich stage as a primary contributor to NO x emissions – driven both by increased heat loss and reduced mixing rates. Furthermore, heat losses have been shown to create conditions that are conducive to increased N 2 O formation in the lean stage. In conclusion, the results of this study will be considered in the context of developing optimized two-stage RQL combustors for ammonia.

Combustion↗

Sensitizing effects of NO{sub x} on CH{sub 4} oxidation at high pressure

The CH{sub 4}/O{sub 2}/NO{sub x} system is investigated in a laboratory-scale high pressure laminar flow reactor with the purpose of elucidating the sensitizing effects of NO{sub x} on CH{sub 4} oxidation at high pressures and medium temperatures. Experiments are conducted at 100, 50, and 20 bar, 600-900 K, and stoichiometric ratios ranging from highly reducing to oxidizing conditions. The experimental results are interpreted in terms of a detailed kinetic model drawn from previous work of the authors, including an updated reaction subset for the direct interactions of NO{sub x} and C{sub 1-2} hydrocarbon species relevant to the investigated conditions. The results reveal a significant decrease in the initiation temperature upon addition of NO{sub x}. A similar effect is observed with increasing pressure. The sensitizing effect of NO{sub x} is related to the hydrocarbon chain-propagating NO/NO{sub 2} cycle operated by NO{sub 2}+CH{sub 3}{r_reversible}NO+CH{sub 3}O and NO+CH{sub 3}OO{r_reversible}NO{sub 2}+CH{sub 3}O as well as the formation of chain-initiating OH radicals from interactions between NO/NO{sub 2} and the H/O radical pool. At low temperatures, reactions between NO/NO{sub 2} and CH{sub 3}O/CH{sub 2}O also gain importance. The results indicate a considerable intermediate formation of nitromethane (CH{sub 3}NO{sub 2}) as a characteristic high-pressure phenomenon. The formation of CH{sub 3}NO{sub 2} represents an inactivation of NO{sub x}, which may result in a temporary reduction of the overall hydrocarbon conversion rate. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A circular combustor configuration with multiple injection ports for mixing enhancement

A circular combustor design by Ghorashi (1988) which resembles a continuously-stirred tank reactor with multiple injection ports is presented with a view to the enhanced control of mixing, NO(x) reduction, and combustion efficiency maximization. Attention is given to the prototype apparatus for this type of circular combustor, which takes the form of a transparent cold-flow reactor for flow visualization studies under 'chemically frozen' conditions.

Ghorashi, B.↗