Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electronic thermal conductivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Nanoscale Decoupling of Carrier-Phonon Transport in Carbon Nanotube-Halide Perovskite Heterostructures

In conventional semiconductors, electrical and thermal conductivity are typically coupled, posing a challenge in optimizing both simultaneously. Overcoming this inherent trade-off enables strategies for advancing electronic applications. Herein, a strategy is demonstrated to decouple electrical and thermal conductivity trade-off by creating heterostructures of highly conductive single-walled carbon nanotubes (SWCNTs) coated with low conductivity hybrid perovskites. Coating SWCNTs with methylammonium lead iodide perovskite results in an enhancement in electrical conductivity (408-1266 S cm-1) due to p-type doping followed by a threefold decrease of the in-plane thermal conductivity (3.3-1 W m-1 K-1), compared to pristine SWCNTs. Molecular dynamics simulations uncover phonon boundary scattering at the SWCNT/perovskite interface as well as localization of methylammonium-related and softening of the Pb-I-related phonon modes in methylammonium lead iodide perovskite decreasing the thermal conductivity.

14 SOLAR ENERGY↗
NASA NTRS1977

Thermally conductive flows in coronal holes

A treatment of polytropic solar wind flows in non-radial expansion regions, developed by Kopp and Holzer (1976), is extended to include the effect of thermal conduction. Thermal conductive and polytropic flows in the lower corona under specified high-speed stream conditions at 1 AU are compared; the thermally conductive flows more closely model the observed phenomena, though predicted electron density is still too low and the predicted temperature too high. It is suggested that another mechanism (such as wave pressure), in conjunction with thermal conduction, may provide an accurate explanation for solar wind flows originating in coronal holes.

Steinolfson, R. S.↗
DOE OSTI2025

Photocurrent Nanoscopy of Quantum Hall Bulk

Understanding nanoscale electronic and thermal transport of two-dimensional (2D) electron systems in the quantum Hall regime, particularly in the bulk insulating state, poses considerable challenges. One of the primary difficulties arises from the presence of chiral edge channels, whose transport behavior obscures the investigation of the insulating bulk. Using near-field optical and photocurrent nanoscopy, we probe real-space variations of the optical and thermal dynamics of graphene in the quantum Hall regime without relying on complex sample or electrode geometries. Near the charge-neutrality point, we detect strong optical and photothermal signals from resonant inter-Landau-level (LL) magnetoexciton excitations between the zeroth and ± 1 st LLs, which gradually weaken with increasing doping due to Pauli blocking. Interestingly, at higher doping levels and full-integer LL fillings, photothermal signals reappear across the entire sample over an approximately 10 − μ m scale, indicating unexpectedly long cooling lengths and nonlocal photothermal heating through the insulating bulk. This observation suggests that thermal conductivity persists for the localized states even as electronic transport is suppressed—a clear violation of the Wiedemann-Franz law. Our experiments provide novel insights into nanoscale thermal and electronic transport in incompressible 2D gases, highlighting the roles of magnetoexcitons and chiral edge states in the thermo-optoelectric dynamics of the Dirac quantum Hall state. Published by the American Physical Society 2025

36 MATERIALS SCIENCE↗
NASA NTRS1998

Conditions for Aeronomic Applicability of the Classical Electron Heat Conduction Formula

Conditions for the applicability of the classical formula for heat conduction in the electrons in ionized gas are investigated. In a fully ionised gas ( V(sub en) much greater than V(sub ei)), when the mean free path for electron-electron (or electron-ion) collisions is much larger than the characteristic thermal scale length of the observed system, the conditions for applicability break down. In the case of the Venus ionosphere this breakdown is indicated for a large fraction of the electron temperature data from altitudes greater than 180 km, for electron densities less than 10(exp 4)/cc cm. In a partially ionised gas such that V(sub en) much greater than V(sub ei) there is breakdown of the formula not only when the mean free path of electrons greatly exceeds the thermal scale length, but also when the gradient of neutral particle density exceeds the electron thermal gradient. It is shown that electron heat conduction may be neglected in estimating the temperature of joule heated electrons by observed strong 100 Hz electric fields when the conduction flux is limited by the saturation flux. The results of this paper support our earlier aeronomical arguments against the hypothesis of planetary scale whistlers for the 100 Hz electric field signal. In turn this means that data from the 100 Hz signal may not be used to support the case for lightning on Venus.

Cole, K. D.↗
DOE OSTI2022

Thermal conductivity of RHIC superconducting magnet insulation materials at low temperatures

The Electron-Ion Collider (EIC) is planned to be built upon the Relativistic Heavy Ion Collider (RHIC), which vacuum chamber will need to be upgraded to host the EIC hadron beams. For the beam pipe section running through the RHIC superconducting (SC) magnets, the baseline is to insert a screen that will get cooled by thermal contact to the 4.55 K beam pipe of RHIC. Knowing the material properties of the cold mass is thus crucial to understand which is the final temperature that the screen and the superconducting coils in the magnets will reach during the passage of the EIC beams. The thermal conductivities of two insulation materials in the RHIC superconducting magnets and a reference material were measured at cryogenic temperatures at the Magnet Science and Technology division of the National High Magnetic Field Laboratory (NHMFL). The measurements were performed in a Quantum Design physical property measurement system. This report explains the motivation behind this work and summarizes the measurement method and results.

43 PARTICLE ACCELERATORS↗
NASA NTRS1980

Limits on the streaming and escape of electrons in thermal models for solar hard X-ray emission

Upper limits on the number of fast electrons streaming through and escaping from a plasma whose electrons have been heated to approximately 100 billion K and confined by a collisionless ion-acoustic thermal conduction front are determined. It is shown that such a front is fairly transparent to fast electrons with velocities much larger than the thermal velocity because the anisotropic ion-acoustic waves cannot scatter them, making them collisionless on a scale much larger than the thickness of the front. The collisionless analog of the collisional thermoelectric field is derived self-consistently and shown to offer a significant impediment to fast electrons because they must climb over a larger potential barrier than in the collisional case. The only factors limiting the escape of electrons able to surmount this barrier are their rate of production and the requirement that they carry less heat flux than the maximum heat flux allowable. The rate of production is determined for the case of a Maxwellian whose tail is being filled collisionally.

Smith, D. F.↗
NASA NTRS1996

Skutterudites for Thermoelectric Applications

ct given. Summary - This paper says an exploratory search at JPL for new, high-performance thermoelectric materials identified a skutterudite family. Skutterudites might be of interest for electronics, and other applications. Several skutterudites have shown very interesting properties: very low thermal conductivity, very high p-type mobility values, large n-type Seebeck values, large number of isostructural materials. A systematic investigation of skutterudites found: it's necessary to understand trends in properties, and the goal should be to determine the best approach for high ZT.

materials↗
DOE OSTI2023

Exploring the $A$-V-Sb landscape beyond $A$$\mathrm{V_3}$ $\mathrm{Sb_5}$: A case study on the $\mathrm{KV_6}$ $\mathrm{Sb_6}$ Kagome compound

Kagome compounds have garnered attention in the past few years for their intriguing magnetic properties arising from spin frustration dictated by the geometry of the Kagome sublattice. In this paper, we highlight the success of the unconventional hydride route for the fast and easy synthesis of the Kagome compound $\mathrm{KV_6}$ $\mathrm{Sb_6}$. Here, high-temperature in situ powder x-ray diffraction (PXRD) studies proved to be useful in hinting at the existence of $\mathrm{KV_6}$ $\mathrm{Sb_6}$, identifying its synthesis conditions, and understanding the reaction mechanism. The crystal structure for $\mathrm{KV_6}$ $\mathrm{Sb_6}$ was determined from high-resolution PXRD data. The compound has a layered structure [$R\overline{3}m, a = 5.5318$ (9) Å, $c = 34.23$ (3)Å 3 $Z = 3$] at room temperature] and features a Kagome bilayer of V atoms. $\mathrm{KV_6}$ $\mathrm{Sb_6}$ is isostructural to the previously reported $\mathrm{RbV_6}$ $\mathrm{Sb_6}$ and $\mathrm{CsV_6}$ $\mathrm{Sb_6}$ compounds. $\mathrm{KV_6}$ $\mathrm{Sb_6}$ is thermally stable in vacuum up to 1173 K, as evident from the high-temperature in situ PXRD and differential scanning calorimetric analysis. Investigation of magnetic properties for $\mathrm{KV_6}$ $\mathrm{Sb_6}$ between 2 and 300 K reveals temperature-independent paramagnetism and an absence of superconductivity, like the Rb and Cs analogs. Furthermore, we compare the magnetic properties of K V 3 Sb 5 , another ternary Kagome compound, synthesized via two different methods: the hydride route and the traditional route from elements. Low-temperature transport property measurements of $\mathrm{KV_6}$ $\mathrm{Sb_6}$ indicate metallic behavior and an intrinsically low thermal conductivity of $\mathrm{1.0 W K^-1}$ $\mathrm{m^-1}$ at 300 K. The layered structure of $\mathrm{KV_6}$ $\mathrm{Sb_6}$ makes it an attractive candidate for deintercalation and doping studies to tune both magnetic and transport properties, laying a foundation for further studies.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ultimate Suppression of Thermal Transport in Amorphous Silicon Nitride by Phononic Nanostructure.

Engineering the thermal conductivity of amorphous materials is highly essential for the thermal management of future electronic devices. Here, we demonstrate the impact of ultrafine nanostructuring on the thermal conductivity reduction of amorphous silicon nitride (a-Si3N4) thin films, in which the thermal transport is inherently impeded by the atomic disorders. Ultrafine nanostructuring with feature sizes below 20 nm allows us to fully suppress contribution of the propagating vibrational modes (propagons), leaving only the diffusive vibrational modes (diffusons) to contribute to thermal transport in a-Si3N4. A combination of the phonon-gas kinetics model and the Allen-Feldmann theory reproduced the measured results without any fitting parameters. The thermal conductivity reduction was explained as extremely strong diffusive boundary scattering of both propagons and diffusIons. These findings give rise to substantial tunability of thermal conductivity of amorphous materials, which enables us to provide better thermal solutions in microelectronic devices.

Tambo, Naoki↗
NASA NTRS1975

Combined environmental effects on polymers

A series of space simulation tests on FEP Teflon and other polymeric thermal control coatings was conducted using UV, electrons, protons and Lyman-alpha wavelength vacuum UV radiation. Interest was centered on simulating synchronous altitude radiation environment conditions. Physical changes in materials included loss of specularity and introduction of a high density of photographable tracking defects on a microscopic scale. An example shows the discharge of trapped electrons when dielectric strength is exceeded. This leaves a portion of the Teflon volume no longer clear, but diffusely transmitting and reflecting. Thermophysical changes included degradation of solar absorptance coefficients as much as five-fold. The situation that prevails for earth orbit contrasted with polymer performance in the solar wind. It is suggested that conductive overcoatings be developed for polymers and other flexible materials, comparable or superior to those available for fused silica SSMs.

Fogdall, L. B.↗
NASA NTRS1975

Propagation of acoustic modes in the transitional ionosphere

Continuum theory is unsatisfactory for describing wave propagation in the transitional ionosphere, since the mean free path is of the same order as the characteristic length (i.e., Knudsen number in this region is of the order of unity). Therefore a transition model in which isotropic electrons behave as a fluid while the ions are governed by the kinetic equation modified by ion-electron collision effects is proposed to study acoustic wave propagation in the upper atmosphere in the altitude region from 500 to 2000 km. The results show that the dissipation of acoustic waves by electrons is through the viscous and thermal conduction effects, and the dissipation of acoustic waves by ions is through Landau damping. Comparisons of the characteristics of acoustic mode propagation and wave dissipation mechanisms in the collision-dominated, transitional from collisional to collisionless, and collisionless media are also discussed.

Hung, R. J.↗
DOE OSTI2022

Understanding Fission Gas Bubble Distribution and Zirconium Redistribution in Neutron-irradiated U-Zr Metallic Fuel Using Machine Learning

U-10wt.% Zr (U-10Zr) based metallic fuel is the leading candidate for next-generation sodium cooled fast reactor in United States. Currently, Idaho National Laboratory (INL) has been the leading national laboratory for research, development, and demonstration (RD&D) on metallic fuel. Advanced post-irradiation characterization will help to understand fuel microstructure and property change during irradiation, benefiting fuel qualification for commercial application. Characterization capabilities ranging from sub-nanometer to micrometer, such as scanning electron microscopy (SEM), focused ion beam (FIB) sampling, transmission electron microscopy (TEM) characterization, and local thermal conductivity microscopy (TCM), have been utilized recently on irradiated U-10Zr fuel samples to gain a better understanding of nuclear fuel microstructure and property evolution inside a reactor. The FIB/SEM coupled with energy dispersive X-ray spectroscopy (EDS) can capture the essential information to achieve better understanding of fuel behaviors. Inside a nuclear reactor, the phase and microstructure of U-10Zr is constantly changing under neutron bombardment. For example, the gaseous fission product atoms have a limited solubility inside fuel matrix and tend to precipitate out in bubble form, which not only contribute to fuel thermal conductivity degradation but also provide a shortcut for movement of fission products, i.e. lanthanides. The resultant deposition of lanthanides at the cladding inner surface will potentially trigger a chemical reaction/interaction between nuclear fuel and cladding at reactor operational conditions, threatening fuel integrity and safety. FIB/SEM coupled with EDS can provide the fission bubble information as well as probe into phase separation or Zr redistribution, which is fundamental to predict the fuel performance. With high velocity image data generating method, such as FIB/SEM, an automatic way to extract the microstructural information quantitively can better serve the needs from post irradiation characterization. A trained machine learning model, named Decision Tree, is employed to generate a bubble classifier and to categorize bubbles into three categories: isolated bubble, connected without lanthanides, and connected with lanthanides bubbles[3]. This work presents a showcase of this approach on six regions of a fuel cross-section along the radial temperature gradient. We obtained distributions of bubble categories and porosity rates along the six regions. Moreover, a secondary phase U-Zr2 was determined and found on regions 5 and 6. The secondary phase fraction was increasing from 15.61% in region 5 to 34.79% in region 6 based on this approach . This quantitative data offers insights into the lanthanide migration and potentially thermal conductivity degradation. This information from machine learning will be fed into fuel design code for better prediction of fuel performance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Thermal Conductivity Measurement of Extrusion-Printed Silver Using Modulated Photothermal Radiometry

Flexible printed electronics is a rapidly growing field with applications in conformal and flexible devices. However, the physical properties of the films created by many state-of-the-art printing methods become highly dependent on printing parameters, resulting in varying thermal properties often differing significantly from their bulk ink components. To understand the influence of the printing process, we build upon our previous work, where a noncontact optical technique, known as modulated photothermal radiometry (MPTR), was used to measure the thermal conductivity of aerosol-jet-printed thin films. In this work, we use the method to study the thermal properties of extrusion-printed silver on glass and alumina substrates. A noise-resistant data analysis fitting technique is applied using a 2-D heat transfer model. Here, the thermal conductivity measurement is validated using the Weidemann-Franz (WF) relationship from measured electrical conductivity values.

42 ENGINEERING↗
DOE OSTI2020

Optical properties of cubic boron arsenide

The ultrahigh thermal conductivity of cubic boron arsenide (BAs) makes it a promising material for next-generation electronics and optoelectronics. Here, we report measured optical properties of BAs crystals, including the complex dielectric function, refractive index, and absorption coefficient in the ultraviolet, visible, and near-infrared wavelength range. In this work, the data were collected at room temperature using spectroscopic ellipsometry and transmission and reflection spectroscopy. We further calculated the optical response using density functional theory and many-body perturbation theory, considering quasiparticle and excitonic corrections. The computed values for the direct and indirect bandgaps (4.25 eV and 2.07 eV) agree well with the measured results (4.12 eV and 2.02 eV). Our findings pave the way for using BAs in future electronic and optoelectronic applications that take advantage of its demonstrated ultrahigh thermal conductivity and predicted high ambipolar carrier mobility.

74 ATOMIC AND MOLECULAR PHYSICS↗
NASA NTRSDate not supplied

Thermal Vacuum Testing of the Cryostat Heat Removal System for COSI SMEX

The Cryostat Heat Removal System (CHRS) of the Compton Spectrometer and Imager (COSI) consists of cryocooler, three transport aluminum ammonia Constant Conductance Heat Pipes (CCHP), three radiators with CCHP spreaders and Cryocooler Control Electronics (CCE) attached to a separate radiator. A Thermal Vacuum (TVAC) test was conducted at NASA Goddard Space Flight Center to characterize the integrated COSI CHRS in the flat configuration. This presentation summarizes the measured COSI CHRS performance along with lessons learned.

Pipes↗
NASA NTRSDate not supplied

Conductive Tether Coating for Electrodynamic Tethers

The Propulsive Small Expendable Deployer System (ProSEDS), which is an on-orbit demonstration of the propulsion capabilities of electrodynamic tethers in space, is a secondary payload on a Delta 11 unmanned expendable booster. The ProSEDS tether consists of a 5 km bare electrodynamic tether and a 1 0-km non-conductive leader tether. Near the Delta 11, 160 m of the conductive tether is insulated to prevent plasma electron collection from the plasma contactor and for other science requirements. The remainder of the 5-km conductive tether is coated with a new conductive coating to collect plasma electrons. A bare metal tether easily collects electrons from the plasma, but thermal concerns preclude this design. A highly emissive conductive polymer developed by Triton Systems, Inc. has been optimized for both conductivity and thermo-optical properties. The current design for the ProSEDS conductive tether is seven individually coated strands of 28 AWG aluminum wire, coated with an atomic oxygen-resistant conductive polymer composed of a mixture of COR (Colorless Oxygen Resistant) and polyanaline (PANI) known as C-COR (Conductive-Colorless Oxygen Resistant). The conductive-coated wire strands are cold-welded to individually coated strands of the insulated tether. The insulated tether is coated with 1 mil of polyimide and an atomic oxygen resistant polymer TOR-BP. The insulated tether must stand off the entire voltage of the tether (1 200 V) at various times during the mission. All seven wires are twisted around a Kevlar-29 core using the Hi-wire design. Extensive testing has been performed at the Marshall Space Flight Center to qualify both the conductive coating and insulating coating for use on the ProSEDS tether. The conductive coating has been exposed to a plasma to verify the coatings ability to collect electrons from the space plasma from 0 to 1500 V, and to verify the coatings ability to collect electrons after atomic oxygen exposure. The insulated coating has been tested to verify its dielectric strength both in a vacuum and air. Thermal optical properties on both coatings have been measured before and after atomic oxygen testing. The results of these tests will be presented.

Jason A Vaughn↗