Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electrical safety”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Applications of thermal infrared imagery for energy conservation and environmental surveys

The survey procedures, developed during the winter and summer of 1976, employ color and color infrared aerial photography, thermal infrared imagery, and a handheld infrared imaging device. The resulting imagery was used to detect building heat losses, deteriorated insulation in built-up type building roofs, and defective underground steam lines. The handheld thermal infrared device, used in conjunction with the aerial thermal infrared imagery, provided a method for detecting and locating those roof areas that were underlain with wet insulation. In addition, the handheld infrared device was employed to conduct a survey of a U.S. Army installation's electrical distribution system under full operating loads. This survey proved to be cost effective procedure for detecting faulty electrical insulators and connections that if allowed to persist could have resulted in both safety hazards and loss in production.

Carney, J. R.↗
NASA NTRS1979

Phase 1 of the near team hybrid passenger vehicle development program. Appendix C: Preliminary design data package. Volume 2: Appendices

The design, development, efficiency, manufacturability, production costs, life cycle cost, and safety of sodium-sulfur, nickel-zinc, and lead-acid batteries for electric hybrid vehicles are discussed. Models are given for simulating the vehicle handling quality, and for finding the value of: (1) the various magnetic quantities in the different sections in which the magnetic circuit of the DC electric machine is divided; (2) flux distribution in the air gap and the magnetization curve under load conditions; and (3) the mechanical power curves versus motor speed at different values of armature current.

Piccolo, R.↗
NASA NTRS1980

Health and safety: Preliminary comparative assessment of the Satellite Power System (SPS) and other energy alternatives

Data readily available from the literature were used to make an initial comparison of the health and safety risks of a fission power system with fuel reprocessing; a combined-cycle coal power system with a low-Btu gasifier and open-cycle gas turbine; a central-station, terrestrial, solar photovoltaic power system; the satellite power system; and a first-generation fusion system. The assessment approach consists of the identification of health and safety issues in each phase of the energy cycle from raw material extraction through electrical generation, waste disposal, and system deactivation; quantitative or qualitative evaluation of impact severity; and the rating of each issue with regard to known or potential impact level and level of uncertainty.

Habegger, L. J.↗
NASA NTRS1982

Design description of the Tangaye Village photovoltaic power system

The engineering design of a stand alone photovoltaic (PV) powered grain mill and water pump for the village of Tangaye, Upper Volta is described. The socioeconomic effects of reducing the time required by women in rural areas for drawing water and grinding grain were studied. The suitability of photovoltaic technology for use in rural areas by people of limited technical training was demonstrated. The PV system consists of a 1.8-kW (peak) solar cell array, 540 ampere hours of battery storage, instrumentation, automatic controls, and a data collection and storage system. The PV system is situated near an improved village well and supplies d.c. power to a grain mill and a water pump. The array is located in a fenced area and the mill, battery, instruments, controls, and data system are in a mill building. A water storage tank is located near the well. The system employs automatic controls which provide battery charge regulation and system over and under voltage protection. This report includes descriptions of the engineering design of the system and of the load that it serves; a discussion of PV array and battery sizing methodology; descriptions of the mechanical and electrical designs including the array, battery, controls, and instrumentation; and a discussion of the safety features. The system became operational on March 1, 1979.

Martz, J. E.↗
NASA NTRS1987

The results of application studies for space nuclear power

The results are summarized of the studies over the last several years to identify and characterize potential applications for the SP-100 space nuclear reactor power system in powering spacecraft. SP-100 is a space power system based on a fast spectrum nuclear reactor with thermoelectric power conversion and liquid metal and heat pipe thermal transport. SP-100 reactor systems are designed to provide electric power with user designated characteristics at levels in the range from 10 to 1000 kWe. The use of nuclear reactors such as SP-100 as a power source provides a potential means of providing uninterrupted electrical power as required for many of todays space missions within acceptable cost and safety constraints.

Isenberg, L.↗
NASA NTRS1987

Past, present, and future activities in space power technology in the United States of America

Space power technology research in the U.S. is examined. The objectives for advanced power systems are long life, safety, flexibility, modularity, growth capability, and autonomy. Research in the areas of photovoltaic arrays, electrical energy storage, and the development of solar dynamic power systems and radio thermal generators is described. The applications of advances in power generation, energy storage, and power management and distribution to the Space Station are discussed.

Ambrus, Judith H.↗
NASA NTRS1995

Improved Spline Coupling For Robotic Docking

Robotic docking mechanism like one described in "Self-Aligning Mechanical and Electrical Coupling" (GSC-13430) improved. Spline coupling redesigned to reduce stresses, enchancing performance and safety of mechanism. Does not involve significant increase in size. Convex spherical surfaces on spline driver mate with concave spherical surfaces on undersides on splines in receptacle. Spherical surfaces distribute load stresses better and tolerate misalignments better than flat and otherwise shaped surfaces.

Vranish, John M.↗
NASA NTRS2003

A Brighter Choice for Safety

Emergency exit signs can be lifesavers, but only if they remain visible when people need them. All too often, power losses or poor visibility can render the signs ineffective. Luna Technologies International, Inc., of Kent, Washington, is shining new light on this safety issue. The company s LUNAplast(trademark) product line illuminates without the need for electricity, maintenance, or a power connection. LUNAplast, which benefited from tests conducted at Johnson Space Center, is so successful that NASA engineers selected it for the emergency exit pathway indicators on the International Space Station (ISS).

Source record↗
NASA NTRS2021

NASA Engineering and Safety Center Technical Bulletin No. 19-01-1: Mitigating Risks of Single-Event Effects in Space Applications

Since most Electrical, Electronic, and Electromechanical (EEE) parts are intended for terrestrial applications, they are susceptible to a range of radiation threats in the space environment if the resulting effects are not properly characterized and mitigated. Even specially designed radiation-hardened parts may not be tolerant to all types of radiation effects. Radiation hardness is a multi-dimensional property of any part that describes intrinsic abilities to tolerate various radiation environments [1,2]. Effects to be concerned with include total ionizing dose, total non-ionizing dose, and single-event effects (SEE) – all of which depend on the mission, environment, application, and lifetime. Radiation effects concerns may be the same whether a EEE part is Commercial-Off-The-Shelf (COTS), MIL-SPEC, or some other variant, all of which are susceptible to the same radiation threats [3]. SEE consequences range from recoverable faults to catastrophic failure. Like other random faults, SEE can be mitigated with informed circuit design practices at the device, card, and/or system level.

Single-event effects↗
NASA NTRS2000

Ruthenium Oxide Electrochemical Super Capacitor Optimization for Pulse Power Applications

Electrical actuator systems are being pursued as alternatives to hydraulic systems to reduce maintenance time, weight and costs while increasing reliability. Additionally, safety and environmental hazards associated with the hydraulic fluids can be eliminated. For most actuation systems, the actuation process is typically pulsed with high peak power requirements but with relatively modest average power levels. The power-time requirements for electrical actuators are characteristic of pulsed power technologies where the source can be sized for the average power levels while providing the capability to achieve the peak requirements. Among the options for the power source are battery systems, capacitor systems or battery-capacitor hybrid systems. Battery technologies are energy dense but deficient in power density; capacitor technologies are power dense but limited by energy density. The battery-capacitor hybrid system uses the battery to supply the average power and the capacitor to meet the peak demands. It has been demonstrated in previous work that the hybrid electrical power source can potentially provide a weight savings of approximately 59% over a battery-only source. Electrochemical capacitors have many properties that make them well-suited for electrical actuator applications. They have the highest demonstrated energy density for capacitive storage (up to 100 J/g), have power densities much greater than most battery technologies (greater than 30kW/kg), are capable of greater than one million charge-discharge cycles, can be charged at extremely high rates, and have non-explosive failure modes. Thus, electrochemical capacitors exhibit a combination of desirable battery and capacitor characteristics.

Merryman, Stephen A.↗
NASA NTRS1988

Commercial objectives, technology transfer, and systems analysis for fusion power development

Fusion is an inexhaustible source of energy that has the potential for economic commercial applications with excellent safety and environmental characteristics. The primary focus for the fusion energy development program is the generation of central station electricity. Fusion has the potential, however, for many other applications. The fact that a large fraction of the energy released in a DT fusion reaction is carried by high energy neutrons suggests potentially unique applications. In addition, fusion R and D will lead to new products and new markets. Each fusion application must meet certain standards of economic and safety and environmental attractiveness. For this reason, economics on the one hand, and safety and environment and licensing on the other, are the two primary criteria for setting long range commercial fusion objectives. A major function of systems analysis is to evaluate the potential of fusion against these objectives and to help guide the fusion R and D program toward practical applications. The transfer of fusion technology and skills from the national labs and universities to industry is the key to achieving the long range objective of commercial fusion applications.

Dean, Stephen O.↗
NASA NTRSDate not supplied

Urban Air Mobility Airspace Dynamic Density Safety Metric

NASA’s Advanced Air Mobility (AAM) project focuses on enabling emerging aviation markets by accelerating development of safe, high-volume flight operations.[1] It involves development and validation of vehicles, airspace, and automation changes required to support concepts such as Urban Air Mobility, a vision for electric or hybrid electric, vertical or short take-off and landing vehicles that can transport passengers and cargo over an urban environment.[2] NASA’s System Wide Safety (SWS) project is coordinating with AAM by understanding how safety could be affected by these emerging operations. We approach the assessment of airspace safety by identifying threats to operations and then monitoring and predicting the evolution of those threats encoded in a set of safety metrics.[3] Toward this end, we have been developing a dynamic density metric to predict the likelihood of vehicle conflicts in the airspace.

Dynamic Density↗
NASA NTRS1980

The MOD-OA 200 kilowatt wind turbine generator design and analysis report

The project requirements, approach, system description, design requirements, design, analysis, system tests, installation safety considerations, failure modes and effects analysis, data acquisition, and initial performance for the MOD-OA 200 kw wind turbine generator are discussed. The components, the rotor, driven train, nacelle equipment, yaw drive mechanism and brake, tower, foundation, electrical system, and control systems are presented. The rotor includes the blades, hub and pitch change mechanism. The drive train includes the low speed shaft, speed increaser, high speed shaft, and rotor brake. The electrical system includes the generator, switchgear, transformer, and utility connection. The control systems are the blade pitch, yaw, and generator control, and the safety system. Manual, automatic, and remote control and Dynamic loads and fatigue are analyzed.

Andersen, T. S.↗
NASA NTRS1973

Nuclear safety considerations for the design of a shuttle launched 500 to 2000 watt isotope Brayton power system.

An extensive study was conducted to evaluate the safety requirements for the design of a heat source assembly for use in a shuttle launched, isotope Brayton electric power system for the 500-W(e) to 2 kWe range. The assembly is a self-contained package which supplies heat to a power conversion system. A typical mission profile for a shuttle launched, earth orbital mission was assumed. Critical mission accidents were identified and evaluated to determine their impact upon the design of the Heat Source Assembly. Earth-orbital decay reentry analyses were performed to demonstrate survivability of the heat source. Safety design requirements were developed to ensure survivability under credible accident conditions including loss of the power conversion system in orbit.

Garate, J. A.↗
NASA NTRSDate not supplied

Power System Human Machine Interfaces for the X-57 Mod II Aircraft

The transition from a Tecnam (Costruzioni Aeronautiche Tecnam srl) (Sapua, Italy) P2006T twin-engine aircraft into the fully electric X-57 Modification II (Mod II) configuration required the development of cockpit displays and controls to allow the pilot to properly monitor and interface with the research electric system. This paper describes the machine interfaces developed to interface with the X-57 Mod II traction battery system and the unique considerations of developing interfaces and monitoring tools for electric aircraft. The key design philosophy during the X-57 cockpit development was to retain or make minor modifications to the stock P2006T aircraft wherever possible and to use highly reliable commercial displays for monitoring of safety critical parameters. From these efforts, development of accurate estimates of battery state of charge and energy meters designed specifically for flight applications for future electric aircraft development is recommended.

James Reynolds↗