SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Thin-film electrically resistive heater applies high, controlled flux of heat to surface of object. Heater mounted directly on surface of object. It is small, simple to operate, and less expensive than laser and arc heating facilities. Because only other equipment needed appropriate power supply, thin-film heater essentially portable device useful in wide range of eventual applications in research and in field.
Doping polyimides with cobalt ion causes the room temperature direct current electrical resistivity to decrease relative to the polymer alone, the reduction being most pronounced for the air-side of the cobalt modified polyimides. At a constant electrical field, resistivity for the volume, air-side and glass-side modes decreases yet further with an increase in temperature as expected for semiconductors and insulators. X-ray photoelectron spectroscopy indicates the air-side of the cobalt modified polyimides is predominantly Co3O4. The bulk resistivity of the air-side and activation energy of conduction for this surface are comparable to high purity sintered Co3O4. Charging characteristics at room temperature indicate a substantial polymer matrix contribution to both the glass-side and volume mode measurements but a negligible contribution to the air-side electrical properties. Volume electrical resistivity for similar additive levels is reduced by increasing the molecular flexibility of the host polymer.
Explore the source record for details and available documents.
A predictive analytical model is presented for the electrical conductivity of multi-principal-element alloys (MPEAs), including those containing aluminum, transition metals, and refractory metals. Given that the lattice parameter of the Wigner-Seitz cell of an MPEA is similarly variable to a bulk metallic glass, it is postulated that electron scattering can be approximated by a series of two-level systems. Here, the resulting reduced-order model enabled an accurate determination of electrical resistivity and electron thermal conductivity based on the scattering of electrons in a two-level system across a Bloch-potential-based virtual crystal approximation. Model results are compared to experimental four-point probe electrical resistivity measurements between 300 K and 700 K for Al 0.3 CoCrCuFeNi, CoCrFeMnNi, (CoCrFeMnNi) 0.98 W 0.02 , (CoCrFeMnNi) 0.95 W 0.05 , and Nb 4 Ta 4 V 3 Ti, for model validation.
Misfit dislocation arrays (MDAs) at semi-coherent heterogeneous interface have been demonstrated effectiveness to trap and then outgas helium (He) for alleviating void swelling in metals, but limited by atomic-level thin film deposition that is difficult to scale-up for industrial production. In this work, we proposed an innovative strategy that could generate semi-coherent homophase interfaces in a same grain by varying surface energy density assisted by high-temperature graphene (Gr) deposition. This strategy transforms strain energy and surface energy, two originally distinctive processes into successive processes, and demonstrates experimentally and theoretically by introducing {111} copper (Cu) in a {100} Cu grain. Subsequent He implantation and electrical resistivity measurement results suggest that high-density MDAs originated at this {111}/{100} interface could form stable He nanochannels near Cu surface with Gr assistance, manifesting by ultra-low increased ratio of the electrical resistivity (i.e. ~3800% of Cu vs. ~90% of Gr/Cu) after He implantation. Finally, the present findings may provide a new strategy for efficiently managing He and achieving surface protection of advanced metals, merely by depositing a super-rigid material on metal surface to greatly reduce surface energy density.
Utilizing a combination of dynamical mean field theory (DMFT) and density functional theory, it has been theoretically proposed that PuB 6 is a strongly correlated topological insulator characterized by nontrivial 𝐙 2 topological invariants and metallic surface states [X. Deng et al., Phys. Rev. Lett. 111, 176404 (2013)]. Here, we demonstrate through low-temperature magnetotransport measurements and first-principles calculations that PuB 6 exhibits characteristics of a topological Kondo insulating state. These features include a transition in electrical resistivity from high-temperature, thermally activated behavior with a narrow gap at the Fermi level (Δ𝜌 ∼ 20 meV) to a distinctive low-temperature plateau, as well as a surface-to-volume dependence of electrical resistivity at low temperatures. The topological nature of PuB 6 is further supported by the theoretical calculations, which show that GGA + 𝑈 is capable of capturing electronic, topological, and lattice properties of PuB 6 with much lower computational cost than DMFT.
Abstract The long‐term containment of high‐level radioactive waste in geological disposal repositories relies on Engineered Barrier Systems (EBS), with bentonite clay emerging as a candidate material due to its unique properties. Understanding moisture dynamics within bentonite buffers is crucial for EBS performance, as it directly influences the material's swelling capacity, thermal and hydraulic conductivity, mechanical properties, and long‐term evolution under complex thermal‐hydrological‐mechanical (THM) processes. This study develops an advanced Electrical Resistivity Tomography (ERT)‐based framework to quantitatively monitor moisture dynamics under THM conditions. Our framework extends the Waxman‐Smits model to incorporate the coupled effects of temperature, water content, fluid chemistry, and mechanical changes on bentonite's electrical properties. Utilizing HotBENT‐Lab data from our companion paper, which includes electrical conductivity, CT density, and thermocouple measurements, this study offers a novel methodological framework bridging different scales of the model. Our results show that the extended model can estimate water content from ERT data, capturing spatial and temporal variations in moisture distribution within bentonite columns. However, the model tends to overestimate water content compared to CT density‐derived measurements. We address this discrepancy by incorporating a simplified swelling effect model, which improves agreement between ERT and CT density‐based water content estimates. We also discuss model limitations, including simplified treatment of swelling and micropore effects, and propose a conceptual framework for transitioning from laboratory to field applications, addressing challenges such as parameter scalability, field validation methods, and integration of diverse data sources. This ERT‐based framework can potentially advance real‐world moisture monitoring of bentonite‐based EBS in nuclear waste repositories. Plain Language Summary Safely containing high‐level radioactive waste depends on barriers made from materials like bentonite clay, which is effective because it swells and seals in the waste. To ensure these barriers work well over time, it's important to understand how moisture moves through the clay. Our study developed a new method using ERT to monitor moisture levels in bentonite under conditions that mimic those in actual storage sites, including changes in temperature, water content, and mechanical stress. This study improved an existing model to better account for how these factors affect the clay, allowing us to create more accurate moisture maps. Initially, the proposed model overestimated the amount of water in the clay, but its accuracy was improved by factoring in how the clay swells when wet. This study also identified some limitations of the model and suggested ways to adapt it for use in real‐world waste storage sites. This new approach could lead to better monitoring and safety checks for nuclear waste storage systems, helping to ensure long‐term containment. Key Points This work develops an ERT‐based framework extending the Waxman‐Smits model to monitor bentonite moisture dynamics during coupled THM processes The extended model accurately estimates water content from Electrical Resistivity Tomography data, incorporating swelling effects to improve precision This work proposes a conceptual framework for transitioning from laboratory to field applications, advancing EBS monitoring in nuclear waste repositories
Researchers at the NASA Glenn Research Center have developed a new air-mass-flow sensor to solve the problems of existing mass flow sensor designs. NASA's design consists of thin-film resistors in a Wheatstone bridge arrangement. The resistors are fabricated on a thin, constant-thickness airfoil to minimize disturbance to the airflow being measured. The following photograph shows one of NASA s prototype sensors. In comparison to other air-mass-flow sensor designs, NASA s thin-film sensor is much more robust than hot wires, causes less airflow disturbance than pitot tubes, is more accurate than vane anemometers, and is much simpler to operate than thermocouple rakes. NASA s thin-film air-mass-flow sensor works by converting the temperature difference seen at each leg of the thin-film Wheatstone bridge into a mass-flow rate. The following figure shows a schematic of this sensor with air flowing around it. The sensor operates as follows: current is applied to the bridge, which increases its temperature. If there is no flow, all the arms are heated equally, the bridge remains in balance, and there is no signal. If there is flow, the air passing over the upstream legs of the bridge reduces the temperature of the upstream legs and that leads to reduced electrical resistance for those legs. After the air has picked up heat from the upstream legs, it continues and passes over the downstream legs of the bridge. The heated air raises the temperature of these legs, increasing their electrical resistance. The resistance difference between the upstream and downstream legs unbalances the bridge, causing a voltage difference that can be amplified and calibrated to the airflow rate. Separate sensors mounted on the airfoil measure the temperature of the airflow, which is used to complete the calculation for the mass of air passing by the sensor. A current application for air-mass-flow sensors is as part of the intake system for an internal combustion engine. A mass-flow sensor is used to provide accurate information about the amount of air entering the engine so that the amount of fuel can be adjusted to give the most efficient combustion. The ideal mass-flow sensor would be a rugged design that minimizes the disturbance to the flow stream and provides an accurate reading of both smooth and turbulent flows; NASA's design satisfies these requirements better than any existing design. Most of the mass-flow sensors used today are the hot wire variety. Hot wires can be fragile and cannot accurately measure a turbulent or reversing flow, which is often encountered in an intake manifold. Other types of mass-flow sensors include pitot tubes, vane anemometers, and thermocouple rakes-all of which suffer from some type of performance problem. Because it solves these performance problems while maintaining a simple design that lends itself to low-cost manufacturing techniques, NASA s thin-film resistance temperature detector air-mass-flow sensor should lead to more widespread use of mass-flow sensors.
Hafnium nitride coatings were deposited by reactive RF sputtering from a hafnium target in nitrogen and argon gas mixtures. The rate of deposition, composition, electrical resistivity and complex index of refraction were investigated as a function of target substrate distance and the fraction nitrogen, (fN2) in the sputtering atmosphere. The relative composition of the coatings is independent on fN2 for values above 0.1. The electric resistivity of the hafnium nitride films changes over 8 orders of magnitude when fN2 changes from 0.10 to 0.85. The index of refraction is almost constant at 2.8(1-0.3i) up to fN2 = 0.40 then decreases to 2.1(1 - 0.01i) for higher values of fN2.
The paper reports the results of measurements (Seebeck and Hall coefficients, electrical resistivity, and thermal conductivity) on silicon-germanium (Si-20 at. pct Ge) alloy with boron phosphide, B(6.5)P) as an additive, prepared as described by McLane et al. (1986). The power factor (Seebeck coefficient squared divided by electrical resistivity) and the thermal conductivity of SeGe/B(6.5)P material were found to be lower than for the 'standard' SiGe (Si-22 at. pct Ge) material. However, no net improvement was achieved in the figure-of-merit of the sample tested. It is suggested that structural inhomogeneities, revealed by a SEM examination, might be responsible for this lack of improvement.
More efficient power conversion devices are able to transmit greater electrical power across larger distances to satisfy growing global electrical needs. A critical requirement to achieve more efficient power conversion are the soft magnetic materials used as core materials in transformers, inductors, and motors. To that effect it is well known that the use of non-equilibrium microstructures, which are, for example, nanocrystalline or consist of single phase solid solutions, can yield high saturation magnetic polarization and high electrical resistivity necessary for more efficient soft magnetic materials. In this work, we synthesized CoFe – P soft magnetic alloys containing nanocrystalline, single phase solid solution microstructures and studied the effect of a secondary intermetallic phase on the saturation magnetic polarization and electrical resistivity of the consolidated alloy. Single phase solid solution CoFe – P alloys were prepared through mechanically alloying metal powders and phase decomposition was observed after subsequent consolidation via spark plasma sintering (SPS) at various temperatures. The secondary intermetallic phase was identified as the orthorhombic (Co x Fe 1-x ) 2 P phase and the magnetic properties of the (Co x Fe 1-x ) 2 P intermetallic phase were found to be detrimental to the soft magnetic properties of the targeted CoFe – P alloy.
Aluminum alloys are finding increasing use in the aerospace and automobile industries due to their attractive low density-high modulus and low density-high strength characteristics. Unfortunately, cyclic stress-strain deformation alters the microstructure of the material. These structural changes can lead to fatigue damage and ultimately service failure. Therefore, in order to assess the integrity of the alloy, a correlation between fatigue damage and a measurable microstructural property is needed. Aluminum 2024-T3, a commonly used commercial alloy, contains many grains (individual crystals) of various orientations. The sizes and orientations of these grains are known to affect the strength, hardness, and magnetic permeability of polycrystalline alloys and metals; therefore, perhaps a relationship between a grain property and the fatigue state can be established. Tension-compression cycling in aluminum alloys can also induce changes in their dislocation densities. These changes can be studied from measurements of the electrical resistivities of the materials. Consequently, the goals of this investigation were: to study the grain orientation of aluminum 2024-T3 and to seek a correlation between the grain orientation and the fatigue state of the material; and to measure the electrical resistivities of fatigued samples of aluminum 2024-T3 and to interpret the findings.
Immiscible GaBi alloys were solidified during free fall in the NASA Marshall Space Flight Center drop tower, which provides about 4.5 seconds of low gravity. The electrical resistivity and magnetic susceptibility were measured as a function of pressure (up to 18 kbar) and temperature (300 K to 4.2 K) of drop tower (DT) and ground control (GC) samples prepared under identical conditions, except for gravity. At ambient pressure the electrical resistance of the DT sample exhibits a broad maximum at 100 K, while that of GC sample decreases rapidly as temperature decreases. Both DT and GC samples become superconducting at 7.7 K. However, a minor second superconducting phase with a transition temperature at 8.3 K is observed only in the DT samples.
The design and control of a novel proof-of-concept active jet engine intake using Nickel-Titanium (Ni-Ti or Nitinol) shape memory alloy (SMA) wire actuators is used to demonstrate the potential of an adaptive intake to improve the fuel efficiency of a jet engine. The Nitinol SMA material is selected for this research due to the material's ability to generate large strains of up to 5 percent for repeated operations, a high power-to-weight ratio, electrical resistive actuation, and easy fabrication into a variety of shapes. The proof-of-concept engine intake employs an overlapping leaf design arranged in a concentric configuration. Each leaf is mounted on a supporting bar that rotates upon actuation by SMA wires electrical resistive heating. Feedback control is enabled through the use of a laser range sensor to detect the movement of a leaf and determine the radius of the intake area. Due to the hysteresis behavior inherent in SMAs, a nonlinear robust controller is used to direct the SMA wire actuation. The controller design utilizes the sliding-mode approach to compensate for the nonlinearities associated with the SMA actuator. Feedback control experiments conducted on a fabricated proof-of-concept model have demonstrated the capability to precisely control the intake area and achieve up to a 25 percent reduction in intake area. The experiments demonstrate the feasibility of engine intake area control using the proposed design.
Several approaches for applying high resistance coatings continuously to graphite yarn were investigated. Two of the most promising approaches involved (1) chemically vapor depositing (CVD) SiC coatings on the surface of the fiber followed by oxidation, and (2) drawing the graphite yarn through an organo-silicone solution followed by heat treatments. In both methods, coated fibers were obtained which exhibited increased electrical resistances over untreated fibers and which were not degraded. This work was conducted in a previous program. In this program, the continuous CVD SiC coating process used on HTS fiber was extended to the coating of HMS, Celion 6000, Celion 12000 and T-300 graphite fiber. Electrical resistances three order of magnitude greater than the uncoated fiber were measured with no significant degradation of the fiber strength. Graphite fibers coated with CVD Si3N4 and BN had resistances greater than 10(exp 6) ohm/cm. Lower pyrolysis temperatures were used in preparing the silica-like coatings also resulting in resistances as high as three orders of magnitude higher than the uncoated fiber. The epoxy matrix composites prepared using these coated fibers had low shear strengths indicating that the coatings were weak.
The synthesis of new materials is the lifeline of solid-state science, and it continues to offer us unique opportunities for testing various theoretical formulations and models on a practical material. Such an avenue, therefore, provides a breeding ground for technological innovations and advancements that can completely revolutionize our world. Here, we report the results of our exploratory syntheses in the Yb–Cd–Sb compositional space that lead to the identification of two new Zintl antimonides, namely, Yb10CdSb9 and Yb14CdSb11. Their crystal structures were established via single-crystal X-ray diffraction methods; the basic electronic and transport properties of the new materials were also characterized. Yb10CdSb9 crystallizes in a disordered variant of the tetragonal Ca10LiMgSb9 structure type with unit cell parameters a = 11.8473(8) Å and c = 17.1302(12) Å (space group P42/mnm). Yb14CdSb11 crystallizes in the tetragonal Ca14AlSb11 structure type with unit cell parameters: a = 16.605(3) Å and c = 12.144(7) Å (space group I41/acd). Although the structures of both compounds can be rationalized within the framework of the Zintl formalism, based on the partitioning of the valence electrons in the much disordered Yb10CdSb9 phase, the charge is indicative of a slightly electron-rich composition. Electronic structure calculations in both cases support the notion of intrinsic semiconductor behavior, as expected for a Zintl phase. The temperature dependence of the electrical resistivity of a single crystal of Yb10CdSb9 is in line with that, and the evolution of the Seebeck coefficient indicates an electron-dominated transport mechanism, and a respectable power factor of 0.71 μW/cm K2 at 460 K can be calculated for Yb10CdSb9. The electrical resistivity of Yb14CdSb11, however, evolves in a semimetallic manner, which could suggest an overdoped sample or degenerate semiconducting behavior.
Here, we report the single crystal growth and characterization of EuIn 2 , a magnetic topological semimetal candidate according to our density functional theory (DFT) calculations. We present results from electrical resistance, magnetization, Mössbauer spectroscopy, and X-ray resonant magnetic scattering (XRMS) measurements. We observe three magnetic transitions at T N1 ~ 14.2 K, T N2 ~ 12.8 K and T N3 ~ 11 K, signatures of which are consistently seen in anisotropic temperature dependent magnetic susceptibility and electrical resistance data. Mössbauer spectroscopy measurements on ground crystals suggest an incommensurate sinusoidally modulated magnetic structure below the transition at T N1 ~ 14 K, followed by the appearance of higher harmonics in the modulation on further cooling roughly below T N2 ~ 13 K, before the moment distribution squaring up below the lowest transition around T N3 ~ 11 K. XRMS measurements showed the appearance of magnetic Bragg peaks below T N1 ~ 14 K, with a propagation vector of $τ$ = ($τ_h$, $\overline{τ}_h$, 0), with $τ_h$ varying with temperature, and showing a jump at T N3 ~ 11 K. The temperature dependence of $τ_h$ between ~ 11 K and 14 K shows incommensurate values consistent with the Mössbauer data. XRMS data indicate that $τ_h$ remains incommensurate at low temperatures and locks into $τ_h$ = 0.3443(1).
Efforts are underway to develop inexpensive, low-power electronic sensors, based on single-walled carbon nanotubes (SWCNTs), for measuring part-per-million and part-per-billion of selected gases (small molecules) at room temperature. Chemically unmodified SWCNTs are mostly unresponsive to typical gases that one might wish to detect. However, the electrical resistances of SWCNTs can be made to vary with concentrations of gases of interest by coating or doping the SWCNTs with suitable materials. Accordingly, the basic idea of the present development efforts is to incorporate thus-treated SWCNTs into electronic devices that measure their electrical resistances.