SEARCH · Engineering Papers

Results for “drag estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS1985

The atmospheric heat budget over the western part of the Tibetan plateau during MONEX, 1979

The heat sources over the western part of the Tibetan Plateau for the period from May 19-August 31, 1979 are calculated. The use of the direct method to compute the total atmospheric heat source is examined. The values for the heat source over western, northwestern, and southwestern Tibet are presented. It is concluded that the atmospheric heat source is smaller during the summer than had been previously estimated; this difference is due to reduced drag coefficients. The northwestern and southwestern heat source values are compared, and it is observed that the northwestern heat source is independent on sensible heating and the southwestern heat source relates to the latent heat (LH). The calculated values correlate with the surface hydrology of these two regions. Time series analyses of the heat source components over the southwestern region reveal that LH is the primary modulator of the total atmospheric heat sources. The relation between the vertical heat distribution and Indian summer monsoons is studied.

Feng, Z.↗

NASA NTRS2010

A Study of Fluid Interface Configurations in Exploration Vehicle Propellant Tanks

The equilibrium shape and location of fluid interfaces in spacecraft propellant tanks while in low-gravity is of interest to system designers, but can be challenging to predict. The propellant position can affect many aspects of the spacecraft such as the spacecraft center of mass, response to thruster firing due to sloshing, liquid acquisition, propellant mass gauging, and thermal control systems. We use Surface Evolver, a fluid interface energy minimizing algorithm, to investigate theoretical equilibrium liquid-vapor interfaces for spacecraft propellant tanks similar to those that have been considered for NASA's new class of Exploration vehicles. The choice of tank design parameters we consider are derived from the NASA Exploration Systems Architecture Study report. The local acceleration vector employed in the computations is determined by estimating low-Earth orbit (LEO) atmospheric drag effects and centrifugal forces due to a fixed spacecraft orientation with respect to the Earth or Moon, and rotisserie-type spacecraft rotation. Propellant/vapor interface positions are computed for the Earth Departure Stage and Altair lunar lander descent and ascent stage tanks for propellant loads applicable to LEO and low-lunar orbit. In some of the cases investigated the vapor ullage bubble is located at the drain end of the tank, where propellant management device hardware is often located.

Zimmerli, Gregory A.↗

NASA NTRS2018

Understanding Friction Stir Welding

This Technical Memorandum explains the friction stir welding process in terms of two basic concepts: the concentration of deformation in a shear surface enveloping the tool and the composition of the overall plastic flow field around the tool from simple flow field components. It is demonstrated how weld structure may be understood and torque, drag, and lateral tool forces may be estimated using these concepts. Some discrepancies between computations and accompanying empirical data are discussed in the text. This work is intended to be helpful to engineers in diagnosing problems and advancing technology.

Nunes, A. C., Jr.↗

NASA NTRS1999

Navigating Mars Global Surveyor Through the Martian Atmosphere: Aerobraking 2

The Mars Global Surveyor (MGS) spacecraft was successfully inserted into an elliptical orbit around Mars on 9/12/97, 01:53:49 UTC. This orbit was near polar (inclination=93.26 deg) with an orbital period of 44.993 hours and apoapsis and periapsis altitudes of 54,025.9 km and 262.9 km respectively. After 201 orbits and 196 days after Mars orbit insertion, the first phase of aerobraking (AB), called AB 1, has ended; after the AB 1 termination maneuver, the orbital period was 11.64 hours with apoapsis and periapsis altitudes of 17,870.3 and 170.7 Ian respectively. Thereafter, MGS was in a science phasing orbit (SPO) and acquired data from the science instruments from 3/28/98 to 9/22/98 (orbits 202 through 572). The second phase of aerobraking (AB2) began on 9/23/98 with the first descent into the atmosphere on P574 and ended with the aerobraking termination maneuver (ABX) on 2/4/99 on A 1284. Just prior to ABX, the apoapsis and periapsis altitudes were 456.5 km and 116.7 km respectively with an orbit period of 1.973 hours, a local mean solar time (LMST) at the descending node of 2 hours, 3.6 minutes and an inclination of 92.9 degrees. AB was responsible for circularization of the MGS orbit. However, two additional orbital conditions had to be satisfied simultaneously. These were a) complete AB2 when the LMST at the descending node was close to 2:00 am and b) the inclination was at 93.0 degrees. This paper describes the navigation of MGS throughout AB2; a companion paper describes the strategy and plan for aerobraking. Navigation challenges involved: a) the estimation of an atmospheric density model for every drag pass or periapsis-passage by analyzing doppler tracking data, b) the generation of a short-term, that is over one to several orbits, accurate atmospheric density predictions, c) maintaining the spacecraft's orbit within upper and lower bounds of atmospheric density or dynamic pressure during each periapsis-passage, and d) the prediction of accurate periapsis-passage times (Tp) over one to fifteen orbits. The density estimation and analysis procedure, evaluation of almost 700 atmospheric densities throughout AB2, the variation and accuracy of density predictions, the Tp prediction accuracy and how effectively we terminated AB2 are the basis of this paper and shall be presented in detail. A summary overview of AB2 is given.

Esposito, P.↗

NASA NTRSDate not supplied

CFD Validation Study of a Hypersonic Cone-Slice-Flap Variable Geometry Configuration

Model validation is the process of determining the degree of accuracy between physical reality and the model. The result of model validation can either be used to improve the model through calibration or quantify the model-form uncertainty. This work focuses on providing the model-form uncertainty through an area metric for a hypersonic cone-slice-flap variable geometry configuration given uncertainty in both the simulation and experimental data. The research here compares two different turbulence models for the simulations. For a variable geometry, performing uncertainty quantification to capture the model-form uncertainty on every configuration is computationally challenging. This work lays out a procedure that can give an accurate representation of the model-form uncertainty using a small number of high-fidelity runs and many low-fidelity runs on multiple configurations. Running this comparison provides a quantifiable measurement for the accuracy of each turbulence model for this type of design. The high-fidelity CFD solver used was VULCAN-CFD and the low-fidelity results came from Cart3D. The experimental data came from the 20-Inch Mach 6 Tunnel located at NASA Langley Research Center. The present work showed that the using both the Spalart and Allamaras and Menter Shear-Stress Transport turbulence models overpredicted the drag and lift coefficient, while underpredicting the pitching moment coefficient. The model-form uncertainty estimate resulted in up to a 13.6% change in the total uncertainty for the drag coefficient, up to a 57.4% change in total uncertainty for the lift coefficient, and up to a 100% change in total uncertainty for the pitching moment coefficient.

Laura M. White↗

NASA NTRS1995

A concept for adaptive performance optimization on commercial transport aircraft

An adaptive control method is presented for the minimization of drag during flight for transport aircraft. The minimization of drag is achieved by taking advantage of the redundant control capability available in the pitch axis, with the horizontal tail used as the primary surface and symmetric deflection of the ailerons and cruise flaps used as additional controls. The additional control surfaces are excited with sinusoidal signals, while the altitude and velocity loops are closed with guidance and control laws. A model of the throttle response as a function of the additional control surfaces is formulated and the parameters in the model are estimated from the sensor measurements using a least squares estimation method. The estimated model is used to determine the minimum drag positions of the control surfaces. The method is presented for the optimization of one and two additional control surfaces. The adaptive control method is extended to optimize rate of climb with the throttle fixed. Simulations that include realistic disturbances are presented, as well as the results of a Monte Carlo simulation analysis that shows the effects of changing the disturbance environment and the excitation signal parameters.

Jackson, Michael R.↗

NASA NTRS1990

The design and flight testing of a long endurance RPV

This paper covers the design process for a long endurance RPV. The 56-pound RPV must operate in the 25-60 knot speed range at low altitudes. An airfoil designed for low-Reynolds-number applications was used with a wing of aspect ratio 22 to reach an estimated L/D(max) of 25. Wing tip feathers were designed to reduce the induced drag. A comparison between the computed aerodynamic predictions and wind-tunnel results is given. The estimated endurance is on the order of 50 hours/gallon of fuel. A three-surface configuration was chosen, and the predicted handling quality and performance results obtained so far are given. The structural challenges in building a lightweight structure for the wing and control surfaces are outlined. The flight test program is currently underway.

Siddiqi, Shahid↗

NASA NTRS1959

Lift, Drag, and Pitching Moments of an Arrow Wing Having 80 Degree of Sweepback at Mach Numbers from 2.48 to 3.51 and Reynolds Numbers up to 11.0 Million

Measurements were made of the lift, drag, and pitching moments on an arrow wing (taper ratio of zero) having an aspect ratio of 1.4 and a leading-edge sweepback of 80 (degrees). The wing was designed to have a subsonic leading-edge and a Clark-Y airfoil with a thickness ratio of 12 percent of the chord perpendicular to the wing leading edge. The wing was tested both with and without the wing tips bent upward in an attempt to alleviate possible flow separation in the vicinity of the wing tips. Small jets of air were used to fix transition near the wing leading edge. Force results are presented for Mach numbers of 2.48, 2.75, 3.04, 3.28, and 3.51 at Reynolds numbers of 3.5 and 9.0 million and for a Mach number of 3.04 at a Reynolds number of 11.0 million. The measured aerodynamic characteristics are compared with those estimated by linear theory. The maximum lift-drag ratio measured was much less than that predicted. This difference is attributed to lack of full leading-edge thrust and to the experimental lift-curve slope being about 20 percent below the theoretical value.

Hopkins, Edward J.↗

NASA NTRS1987

Tracking the GLOMR satellite

The task of day-to-day low orbiting satellite tracking utilizing the NAVSPASUR orbital elements is discussed and methods for improving pass time predictions are presented. Estimates are needed for preprogramming of satellite-initiated communications scheduling which requires an accuracy of approximately 30 seconds. This can be achieved by removing the variance associated with the NAVSPASUR D sub 2 (decay) term. Finally, the shock evidenced in GLOMR's orbit on February 7, 1986 is documented and attributed to a severe solar storm with immediately enhanced drag. GLOMR's life expectancy in orbit is now estimated to have dropped approximately 17% by the end of orbit in early February, 1987.

Reiss, Keith W.↗

NASA NTRS2006

Mars Aerobraking Spacecraft State Estimation by Processing Inertial Measurement Unit Data

Aerobraking is an efficient technique for orbit adjustment of planetary spacecraft, such as Magellan (Venus), Mars Global Surveyor, and Mars Odyssey. Determination of the vehicle state during the aerobraking phase has conventionally been performed using only radiometric tracking data prior to and following the atmospheric drag pass. This approach is sufficiently accurate and timely to meet current mission operational requirements; however, it is expensive in terms of ground support and leads to delayed results because ofthe need for post-drag pass data. This research presents a new approach to estimation of the vehicle state during the atmospheric pass that sequentially incorporates observations from an Inertial Measurement Unit (IMU) and models of the vehicle and environment. The approach, called Inertial Measurements for Aerobraking Navigation (IMAN), is shown to perform at a level comparable to the conventional methods in terms of navigation accuracy and superior to them in terms of availability of the results immediately after completion ofthe pass. Furthermore, the research shows that IMAN can be used to reliably predict subsequent periapsis times and locations over all aerobraking regimes. IMAN also yields accurate peak dynamic pressure and heating rates, critical for a successful corridor control strategy, comparable to navigation team reconstructed values. This research also provides the first instance of the utilization of the Unscented Kalman Filter for the purpose of estimating an actual spacecraft trajectory arc about another planet.

Unscented Kalman Filter↗

NASA NTRS1980

Experimental and theoretical aerodynamic characteristics of two hypersonic cruise aircraft concepts at Mach numbers of 2.96, 3.96, and 4.63

The longitudinal and lateral directional aerodynamic characteristics for two Mach 5 cruise aircraft concepts were determined for test Mach numbers of 2.96, 3.96, and 4.63. Estimates from hypersonic impact theory and first order supersonic linearized theory were compared with data to indicate the usefulness of these methods. The method which applied tangent cone empirical theory to the body and tangent wedge theory to the wings and to the horizontal and vertical tails provided the best estimates. The tangent cone empirical theory applied to all components showed poor agreement with data, and the linear theory estimates were accurate only for lift coefficient and drag coefficient at low angles of attack.

Pittman, J. L.↗

NASA NTRS1980

A study of wing body blending for an advanced supersonic transport

Increases in supersonic cruise lift drag ratio were sought at Mach numbers 2.2 and 2.7 using wing body planform and thickness blending. Constrained twist and camber optimization was performed in the presence of nacelles. Wing and fuselage thickness distributions were optimized for either minimum volume wave drag or minimum total pressure wave drag. The zero leading edge suction lift drag ratios were determined for three wing planforms. The magnitude of the effect of leading edge suction on attainable lift drag ratio was defined on one planform and estimation of available leading edge suction was made.

Goebel, T. P.↗

NASA NTRS1960

Aerodynamic Characteristics at Mach Number 2.05 of a Series of Highly Swept Arrow Wings Employing Various Degrees of Twist and Camber

A series of arrow wings employing various degrees of twist and camber were tested in the Langley 4- by 4-foot supersonic pressure tunnel. Aerodynamic forces and moments in pitch were measured at a Mach number of 2.05 and at a Reynolds number of 4.4 x 10(exp 6) based on the mean aerodynamic chord. Three of the wings, having a leading-edge sweep angle of 70 deg. and an aspect ratio of 2.24, were designed to produce a minimum drag (in comparison with that produced for other wings in the family) at lift coefficients of 0. 0.08, and 0.16. A fourth and a fifth wing, having a 75 deg. swept leading edge and an aspect ratio of 1.65, were designed for lift coefficients of 0 and 0.16, respectively. A 70 deg. swept arrow wing with twist and camber designed for an optimum loading at a lift coefficient considerably less than that for maximum lift-drag ratio gave the highest lift-drag ratio of all the wings tested a value of 8.8 compared with a value of 8.1 for the corresponding wing without twist and camber. Two twisted and cambered wings designed for optimum loading at the lift coefficient for maximum lift-drag ratio gave only small increases in maximum lift-drag ratios over that obtained for the corresponding flat wings. However, in all cases, the lift-drag ratios obtained were far below the theoretical estimates.

Carlson, Harry W.↗

NASA NTRS2003

Direct Validation of the Wall Interference Correction System of the Ames 11-Foot Transonic Wind Tunnel

Data from the test of a large semispan model was used to perform a direct validation of a wall interference correction system for a transonic slotted wall wind tunnel. At first, different sets of uncorrected aerodynamic coefficients were generated by physically changing the boundary condition of the test section walls. Then, wall interference corrections were computed and applied to all data points. Finally, an interpolation of the corrected aerodynamic coefficients was performed. This interpolation made sure that the corrected Mach number of a given run would be constant. Overall, the agreement between corresponding interpolated lift, drag, and pitching moment coefficient sets was very good. Buoyancy corrections were also investigated. These studies showed that the accuracy goal of one drag count may only be achieved if reliable estimates of the wall interference induced buoyancy correction are available during a test.

Ulbrich, Norbert↗

NASA NTRS1991

A drag measurement technique for free piston shock tunnels

A new technique is described for measuring drag with 100-microsecond rise time on a nonlifting model in a free piston shock tunnel. The technique involves interpretation of the stress waves propagating within the model and its support. A finite element representation and spectral methods are used to obtain a mean square optimal estimate of the time history of the aerodynamic loading. Thus, drag is measured instantaneously and the previous restriction caused by the mechanical time constant of balances is overcome. The effectiveness of the balance is demonstrated by measuring the drag on cones with 5 and 15 deg semi-vertex angles in nominally Mach 5.6 flow with stagnation enthalpies from 2.6 to 33 MJ/kg.

Sanderson, S. R.↗

NASA NTRS1985

Estimating unsteady aerodynamic forces on a cascade in a three-dimensional turbulence field

An analytical method has been developed to estimate the unsteady aerodynamic forces caused by flow field turbulence on a wind tunnel turning vane cascade system (vane set). This method approximates dynamic lift and drag by linearly perturbing the appropriate steady state force equations, assuming that the dynamic loads are due only to free stream turbulence and that this turbulence is homogeneous, isotropic, and Gaussian. Correlation and unsteady aerodynamic effects are also incorporated into the analytical model. Using these assumptions, equations relating dynamic lift and drag to flow turbulence, mean velocity, and vane set geometry are derived. From these equations, estimates for the power spectra and rms (root mean squared value, delta) loading of both lift and drag can be determined.

Norman, T.↗

NASA NTRS1986

Estimating unsteady aerodynamic forces on a cascade in a three-dimensional turbulence field

An analytical method has been developed to estimate tne unsteady aerodynamic forces caused by flow field turbulence on a wind tunnel turning vane cascade system (vane set). This method approximates dynamic lift and drag by linearly perturbing the appropriate steady state force equations, assuming that the dynamic loads are due only to free stream turbulence and that this turbulence is homogeneous, isotropic, and Gaussian. Correlation and unsteady aerodynamic effects are also incorporated into the analytical model. Using these assumptions, equations relating dynamic lift and drag to flow turbulence, mean velocity, and vane set geometry are derived. From these equations, estimates for the power spectra and rms (root mean squared value, delta) loading of both lift and drag can be determined.

Norman, T. R.↗

NASA NTRS2012

NASA's Next Solar Sail: Lessons Learned from NanoSail - D2

NanoSail-D2 unfurled January 17th, 2011 and commenced a nine month Low Earth Orbit path to reentry to evaluate a sail's capacity to deploy in space and deorbit satellites. The orbit was strongly affected by variables including but not limited to: initial attitude, orbit lighting, solar radiation pressure, aerodynamic drag, gravity, and Center of Pressure offsets. The effects of these variables were evaluated through a 3-DOF rigid body simulation. The sail experienced stability in orbits which were continuously lit, i.e. did not orbit behind Earth. Probable drag area experienced by the sail for the mission is also estimated from orbital data and compared to the attitude simulation results. Analysis focuses on sail behavior in full lighting conditions to establish the limits of the sails stability in full lighting. Solar radiation pressure, aerodynamic drag, and gravity torque effects are described. Lastly, a reasonable upper bound on the variation of the Center of Pressure from the geometric center of the sail plane is established. Each of these results contributes to the design requirements for future solar sails.

Katan, Chelsea↗